Dielectric and piezoelectric properties of non-stoichiometric (K0.5Na0.5)(Nb0.9+xTa0.1)O3 ceramics

In the study, in order to develop the lead-free piezoelectric ceramics for actuator, transformer and other electronic-devices application, (K_0.5Na_0.5)(Nb_0.9+xTa_0.1)O₃ + 0.5 mol% CuO + 0.2 mol% MnO₂ ceramics were prepared by conventional mixed oxide method. The effects of B-site non-stoichiometry in [(K_0.5Na_0.5)] [(Nb_0.9+xTa_0.1)O₃] ceramics on microstructure and piezoelectric properties were investigated. The density, electromechanical coupling factor (k_p), mechanical quality factor (Q_m), piezoelectric constant (d₃₃), T_C and T_O-T of NKNT ceramics with x = 0.0065 showed the optimum values of 4.58 g/cm³, 0.427, 1554, 109 pC/N, 373 °C and 226 °C, respectively, suitable for piezoelectric motor, and transformer applications.     

Microstructure and piezoelectric properties of Bi0.5(Na0.82K0.18)0.5TiO3−NaSbO3 ceramics

Lead-free piezoelectric ceramics (1−x)Bi_0.5(Na_0.82K_0.18)_0.5TiO₃−xNaSbO₃ have been prepared by a conventional ceramics technique, and their microstructure and electrical properties have been investigated. The addition of NaSbO₃ has no remarkable effect on the crystal structure within the studied doping content; however, an obvious change in microstructure took place. With increase in NaSbO₃ content, the temperature from a ferroelectric to antiferroelectric phase transition increases, and the temperature for a transition from antiferroelectric phases to paraelectric phases changes insignificantly. Simultaneously, the temperature range between the rhombohedral phase transition point and the Curie temperature point becomes smaller. The piezoelectric properties significantly increase with increase in NaSbO₃ content and the piezoelectric constant and electromechanical coupling factor attain maximum values of d₃₃=160 pC/N and k_p=0.333 at x=0.01. The results indicate that (1−x)Bi_0.5(Na_0.82K_0.18)_0.5TiO₃−xNaSbO₃ ceramic is a promising lead-free piezoelectric candidate material.     

Dielectric and piezoelectric properties of lead-free (Na0.5K0.5)NbO3-SrTiO3 ceramics

In this article, we report successful preparation of dense [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ (x=0.005-0.100) ceramics by ordinary sintering in air. The dependence of phase structure on doping content of SrO and TiO₂ has been determined by the X-ray diffraction technique. It was found that the crystal structure changed from orthorhombic to tetragonal at x≈0.040. Dielectric study revealed that the dielectric relaxor behavior was induced by doping of SrO and TiO₂ into (Na_0.5K_0.5)NbO₃. The samples in the composition range from x=0.005 to 0.020 exhibited excellent electrical properties, piezoelectric constant of electromechanical planar and thickness coupling coefficients of k_p=26.6-32.5% and k_t=39.8-43.8%. The results show that the [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ ceramics are one of the promising lead-free materials for electromechanical transducer applications.     

Effects of A-site non-stoichiometry on the structural and electrical properties of 0.96K0.5Na0.5NbO3- 0.04LiSbO3 lead-free piezoelectric ceramics

Effects of A-site non-stoichiometry on the structural and electrical properties of 0.96K0.5+xNa0.5+xNbO3- 0.04LiSbO3 lead-free piezoelectric ceramics were examined for 0 ≤ x ≤ 0.02. The piezoelectric coefficients exhibited a maximum, d33 = 187 pC/N at x = 0.0075, coinciding with the maximum of the grain size and the apparent density at x = 0.0075. The apparent density and the piezoelectric coefficients decreased with increasing x at higher x which was likely due to the crystal geometrical distortion of 0.96K0.5+xNa0.5+xNbO3-0.04LiSbO3. In addition, super-large grains were found and this may be due to liquid phase sintering. Excess (K++Na+) attracted a sum of space charges to keep the charge neutral, resulting in charge leakage during the course of ceramic polarization, influencing the piezoelectric and ferroelectric properties. These findings are of importance for guiding the design of K0.5Na0.5NbO3-based lead-free ceramics with enhanced electrical properties.     

Na0.5K0.5NbO3-BiFeO3 lead-free piezoelectric ceramics

Lead-free (Na_0.5K_0.5)NbO₃-based piezoelectric ceramics were successfully fabricated by substituting with a small amount of BiFeO₃ (BF). Difficulty in sintering of pure NKN ceramics can be eased by adding a few molar percent of BF, and the crystalline structure is also changed, leading to a morphotropic phase boundary (MPB) between ferroelectric orthorhombic and rhombohedral phases. The MPB exists near the 1-2 mol% BF-substituted NKN compositions, exhibiting enhanced ferroelectric, piezoelectric, and electromechanical properties of P_r=23.3 μC/cm², d₃₃=185 pC/N, and k_p=46%, compared to an ordinarily sintered pure NKN ceramics. The MPB composition has a Curie temperature of ∼370 °C, comparable to that of some commercial PZT materials.     

Relationship between phase structure and electrical properties of (K0.5Na0.5)NbO3-LiTaO3 lead-free ceramics

Lead-free piezoelectric ceramics of (1−x)K_0.5Na_0.5NbO₃-xLiTaO₃ (KNN-LT) system have been investigated in this work. X-ray diffraction, Raman spectra measurements, DSC (Differential Scanning Calorimetric), and dielectric constant versus temperature provide direct evidence that the phase transition temperature between tetragonal and orthorhombic shift to lower temperature with the increasing of LT content. The KNN-0.05LT ceramics exhibit the highest high-field d₃₃ up to 220 pm/V. At the same time, we also investigated the relationship between phase structure and electric properties, showing that the orthorhombic phase presents better piezoelectric temperature stabilities than the tetragonal phase. The result may provide a new way for KNN-based lead-free ceramics.     

Structure and electrical properties of Bi0.5(Na, K)0.5TiO3−BiGaO3 lead-free piezoelectric ceramics

Lead-free piezoelectric ceramics (1 − x − y)Bi_0.5Na_0.5TiO₃−xBi_0.5K_0.5TiO₃− yBiGaO₃ have been fabricated by an ordinary sintering technique, and their structure and electrical properties and depolarization temperature have been studied. The results of X-ray diffraction reveal that Bi_0.5K_0.5TiO₃ and BiGaO₃ diffuse into the Bi_0.5Na_0.5TiO₃ lattices to form a new solid solution with a pure perovskite structure. An obvious change in microstructure with increasing concentration of Bi_0.5K_0.5TiO₃ and BiGaO₃ was observed. The piezoelectric constant d₃₃ and the electromechanical coupling factor k_p of the ceramics attain maximum values of 165 pC/N and 0.346 at y = 0.01(x = 0.18) and x = 0.21(y = 0.01), respectively. The temperature dependence of dielectric constant indicates an obvious relaxor characteristic with strong frequency dependence of dielectric constant. The depolarization temperature decreased with increasing content of BiGaO₃ and first decreases and then increases with increasing amount of Bi_0.5K_0.5TiO₃.     

Effects of Li Substitution and Sintering Temperature on Properties of Bi0.5（Na,K）0.5TiO3 Lead-Free Piezoelectric Ceramics

Bi0.5 （Na0.72K0.28- x Lix ）0.5 TiO3 （BNKLT- 100x） lead-free piezoelectric ceramics are synthesized by conventional solid state sintering techniques. The dielectric and piezoelectric properties of the BNKLT-100x ceramics as a function of Li content are systematically investigated. It is found that not only Li content but also the sintering temperature has a strong effect on the piezoelectric properties of BNKLT. The piezoelectric constant d33 Of BNKLT varies from 120 to 252pC/N in the Li content range from 0.03 to 0.16. In the sintering temperature range from 1080 to 1130℃, the d33 value of BNKLT-6 changes from 200pC/N to 252pC/N. The BNKLT-6 sample sintered at 1100℃ has the highest piezoelectric constant d33 of 252pC/N, with the electromechanical coupling factors kp of 0.32 and kt of 0.44.     

Piezoelectric properties of [Li0.03(K0.48Na0.52)0.97](Nb0.97Sb0.03)O3-(Ba0.85Ca0.15)(Ti0.90Zr0.10)O3 lead-free piezoelectric ceramics

[Li_0.03(K_0.48Na_0.52)_0.97](Nb_0.97Sb_0.03)O₃-(Ba_0.85Ca_0.15)(Ti_0.90Zr_0.10)O₃ [(1−x)LKNNS-xBCTZ] lead-free piezoelectric ceramics were prepared by the conventional solid state method, and effects of BCTZ content on the piezoelectric properties of LKNNS ceramics were mainly investigated. A stable solid solution has been formed between LKNNS and BCTZ, and a morphotropic phase boundary of (1−x)LKNNS-xBCTZ ceramics is identified in the range of 0 < x ≤ 0.02. The Curie temperature of (1−x)LKNNS-xBCTZ ceramics decreases with increasing BCTZ content. A higher ?_r value and a lower tan δ value are demonstrated for the (1−x)LKNNS-xBCTZ ceramic with x = 0.02. The (1−x)LKNNS-xBCTZ ceramic with x = 0.02 has an enhanced electrical behavior of d₃₃ ∼ 237 pC/N, k_p ∼ 48.6%, ?_r ∼ 1451, tan δ ∼ 0.037, and T_c ∼ 335 °C. As a result, (1−x)LKNNS-xBCTZ ceramics are promising candidate materials for the field of lead-free piezoelectric materials.     

Evolution from relaxor-like dielectric to ferroelectric in Ba[(Fe0.5Nb0.5)1−xTix]O3 solid solutions

Ba[(Fe_0.5Nb_0.5)_1−xTi_x]O₃ (x=0.2,0.4,0.6,0.8,0.85,0.9 and 0.95) solid solutions were synthesized by a standard solid-state reaction technique. X-ray diffraction at room temperature and dielectric characteristics over a broad temperature and frequency range were evaluated systematically. The structure of Ba[(Fe_0.5Nb_0.5)_1−xTi_x]O₃ solid solutions changed from cubic to tetragonal with increasing x. A Debye-like dielectric relaxation following the Arrhenius law similar to that in Ba(Fe_0.5Nb_0.5)O₃ was observed at lower temperature in the composition range 0.2≤x≤0.8, while the relaxor ferroelectric, diffused ferroelectric and normal ferroelectric behavior were observed for x=0.85,0.9 and 0.95, respectively. The process of the evolution of relaxor-like dielectric to ferroelectric suggested the changing from dilute polar micro-domains to polar micro-domains, polar micro/macro-domains and then polar macro-domains in the present ceramics.     

TiO2-nonstoichiometry dependence on piezoelectric properties and depolarization temperature of (Bi0.5Na0.5)0.94Ba0.06TiO3 lead-free ceramics

(Bi_0.5Na_0.5)_0.94Ba_0.06Ti_xO_1+2x lead-free piezoceramics with x varying from 0.97 to 1.03 were fabricated and characterized in order to investigate the effects of TiO₂-nonstoichiometry on the piezoelectric properties and depolarization temperature of (Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ composition. X-ray diffraction (XRD) analysis showed that all samples have a single phase of perovskite structure with rhombohedral symmetry. Piezoelectric and dielectric measurements revealed that deficiency of TiO₂ leads to an increase in the piezoelectric coefficient (d₃₃), free relative permittivity (), and loss tangent (tan δ) besides an increase in the electromechanical coupling coefficient (k_p) within a certain amount, while excess of TiO₂ results in a decrease in k_p, d₃₃, and , but an increase in tan δ. Depolarization temperature (T_d) measurement indicated a decrease and an increase in T_d as a result of increasing TiO₂ deficiency and TiO₂ excess, respectively. This TiO₂-nonstoichiometry also induced changes in the remanent polarization (P_r) and coercive field (E_c) of the ceramics.     

Effects of Li2CO3 on the sintering behavior and piezoelectric properties of Bi2O3-excess (Bi0.5Na0.5)0.94Ba0.06TiO3 ceramics

(Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ ceramics doped with Li₂CO₃ and Bi₂O₃ as sintering aids were manufactured, and their micro structural, dielectric and piezoelectric properties were investigated. All specimens could be well sintered at a low-temperature of 1080 °C. The bulk density of the specimens doped with a small amount of Li₂CO₃ was enhanced. The dielectric and piezoelectric properties of ceramics were investigated with different amounts of Li₂CO₃ substitutions. High electrical properties of d₃₃ = 167 pC/N, k_p = 0.34, P_r = 40 μC/cm² and E_c = 38 kV/cm were obtained from the specimen containing 0.1 mol% of Li₂CO₃ sintered at 1080 °C.     

Synthesis and ferroelectric properties of bismuth layer-structured (Bi7−xSrx)(Fe3−xTi3+x)O21 solid solutions

Bismuth layer-structured (Bi_7−xSr_x)(Fe_3−xTi_3+x)O₂₁ (BSFT) ceramics were synthesized and the ferroelectric properties and crystal structure were investigated. X-ray powder diffraction profiles and refinement of the lattice parameters indicated single phase BSFT was obtained in the composition range 0-1.5. The lattice parameter b of BSFT remained almost constant, while a slight decrease in the lattice parameter a was observed by the Sr and Ti substitution for Bi and Fe, respectively, which indicated an increase in the orthorhombicity. The dependence of the BSFT lattice parameter on temperature implied a phase transition from the orthorhombic to the tetragonal phase, which was in good agreement with the Curie temperature. The remnant polarization P_r, of BSFT was significantly improved by the Sr and Ti substitution for Bi and Fe, and ranged from 9 to 16 μC/cm², although no remarkable variation in the coercive field E_c was observed. As a result, a well-saturated P-E hysteresis loop of BSFT ceramic was obtained at x=0.5 with a P_r of 30 μC/cm at an applied voltage of 280 kV/cm.     

Na1−xLixNbO3 ceramics studied by X-ray diffraction, dielectric, pyroelectric, piezoelectric and Raman spectroscopy

Na_1−xLi_xNbO₃ ceramics with composition 0.05≤x≤0.30 were prepared by solid-state reaction method and sintered in the temperature range 1100-1150 °C. These ceramics were characterised by X-ray diffraction as well as dielectric permittivity measurements and Raman spectroscopy. Dielectric properties of ceramics belonging to the whole composition domain were investigated in a broad range of temperatures from 300 to 750 K and frequencies from 0.1 to 200 kHz. The Rietveld refinement powder X-ray diffraction analysis showed that these ceramics have a single phase of perovskite structure with orthorhombic symmetry for x≤0.15 and two phases coexistence of rhombohedral and orthorhombic above x=0.20. The evolution of the permittivity as a function of temperature and frequency showed that these ceramics Na_1−xLi_xNbO₃ with composition 0.05≤x≤0.15 present the classical ferroelectric character and the phase transition temperature T_C increases as x content increases. The polarisation state was checked by pyroelectric and piezoelectric measurements. For x=0.05, the piezoelectric coefficient d₃₁ is of 2pC/N. The evolution of the Raman spectra was studied as a function of temperatures and compositions. The results of the Raman spectroscopy study confirm our dielectric measurements, and they indicate clearly the transition from the polar ferroelectric phase to the non-polar paraelectric one.     

Structure and magnetization studies of Nd0.5−xPrxSr0.5MnO3 system

The structural and magnetic properties of Nd_0.5−xPr_xSr_0.5MnO₃ (x=0, 0.1, 0.2, 0.3, 0.4 and 0.5) system have been investigated. With the substitution of Pr in Nd_0.5Sr_0.5MnO₃, it shows a gradual structure transformation from the Imma orthorhombic symmetry to the tetragonal I4/mcm phase, and the crystallographic transition remains incomplete, even in Pr_0.5Sr_0.5MnO₃. A large bifurcation between zero-field-cooled (ZFC) and field-cooled (FC) susceptibility has been observed below Curie temperature (T_C), which is characteristic of coexistence of ferromagnetism (FM) and antiferromagnetism (AFM) at low temperature region. The magnetization of Pr_0.5Sr_0.5MnO₃ is larger than that of Nd_0.5Sr_0.5MnO₃, while Nd_0.5Sr_0.5MnO₃ with more CE-type AFM shows larger magnetization than Nd_0.3Pr_0.2Sr_0.5MnO_3, which mixed with CE-type (majority) and A-type (minority) AFM at low temperature, indicating that the magnetization of Nd_0.5−xPr_xSr_0.5MnO₃ system is affected by A-site disorder combined with orbital ordering of A-type AFM and CE-type AFM.     

Enhanced ferroelectric, magnetic and magnetoelectric properties of Bi1−xCaxFe1−xTixO3 solid solutions

We report on the enhanced electromechanical, magnetic and magnetoelectric properties of Bi_1−xCa_xFe_1−xTi_xO₃ solid solutions. The crystal structure of the x≈0.25 compounds are close to the rhombohedral-orthorhombic phase boundary, and the solid solutions are characterized by increased electromechanical properties due to the polarization extension near the polar-nonpolar border. The homogenous weakly ferromagnetic state is established at x>0.15 doping. The chemical doping shifts the magnetic transition close to room temperature, thus enlarging the magnetic susceptibility of the compounds. The solid solutions at the morphotropic phase boundary exhibit a nearly twofold increase in piezoelectric response, whereas the magnetoelectric coupling shows five times enhancement in comparison with the parent bismuth ferrite.     

Magnetic disorder induced enhanced magneto-resistance in La0.5Sr0.5Co1−xRuxO3

We observe a sharp increase in negative magneto-resistance ratio up to 40% for x=0.1, in La_0.5Sr_0.5Co_1−xRu_xO₃ which is due to the magnetic disorder induced by an anti-ferromagnetic interaction between Co and Ru ions. We also observe a metal to insulator and a ferromagnetic to anti-ferromagnetic transition for 0≤x≤0.3. Ruthenium (IV) ion disrupts an intermediate spin state of cobalt (Co³⁺:t_2g⁵e_g¹), forcing a double exchange mediated ferromagnetic state to an anti-ferromagnetic spin state for x≥0.2.     

Characterization of lead free (K0.5Na0.5)NbO3-LiSbO3 piezoceramic

(K_0.5Na_0.5)NbO₃ (KNN) based lead free ceramics have been fabricated by a solid state reaction. In this work, LiSbO₃ (LS) modified KNN based ceramics were sintered at atmospheric pressure and high density (>96% theoretical) was obtained. The detailed elastic, dielectric, piezoelectric and electromechanical properties were characterized by using the resonance technique combined with the ultrasonic method. The full set of material constants for the obtained polycrystalline ceramics were determined and compared to the pure hot pressed KNN counterpart. KNN-LS polycrystalline ceramic was found to have higher elastic compliance, dielectric permittivity and piezoelectric strain coefficients, but lower mechanical quality factor, when compared to pure KNN, exhibiting a “softening” behavior. However, a high coercive field (∼17 kV/cm) was found for the LS modified KNN material. The properties as a function of temperature were determined in the range of −50-250 ^°C, showing a polymorphic phase transition near room temperature, giving rise to improved piezoelectric behavior.     

A位等价与非等价取代对(K0.5Na0.5)NbO3陶瓷极化的影响

研究了在铌酸钾钠基陶瓷中,A位等价与非等价取代对陶瓷极化温度和极化电场的影响,结果表明:A位等价取代的陶瓷对极化温度和极化电场没有强烈依赖性,可以使极化足够充分,能有效提高铌酸钾钠基陶瓷的压电性能;相反,A位非等价取代的陶瓷对极化温度和极化电场敏感,容易击穿,极化不充分,限制了铌酸钾钠基陶瓷的压电性能. 关键词： 铌酸钾钠 极化 压电     

Electromechanical properties and dielectric behavior of (Bi1/2Na1/2)(1−1.5x)BixTiO3 lead-free piezoelectric ceramics

Bismuth doped bismuth sodium titanate ceramics [(Bi_1/2Na_1/2)_(1−1.5x)Bi_xTiO₃, x=0 to 0.06] were prepared, and the resulting effects on the microstructure and dielectric properties were examined. All of the Bi-doped ceramics exhibited a single phase of perovskite structure with rhombohedral symmetry. The poling leakage current was significantly reduced by the doping of Bi, facilitating the poling process of the ceramics. The doping with Bi enhances the piezoelectric properties and increases the dielectric constant and the dielectric loss of the ceramics. At 2 mol% Bi-doping level, the ceramics exhibit a large remanent polarization of 47 μC/cm² and a relatively low coercive field of 71 kV/cm, while their d₃₃ and k_p reach a maximum value of 95 pC/N and 21%, respectively.