Preparation of poly(styrene-glucidylmethacrylate)/Fe3O4 composite microspheres with high magnetite contents

Magnetic polymer composite microspheres with high magnetite contents were prepared by dispersion polymerization of styrene (St) and glucidylmethacrylate (GMA), in which Fe₃O₄ nanoparticles were co-stabilized by oleic acid and silane surfactants. The microstructure of the composite microspheres was characterized by Fourier transform infrared (FTIR) spectrometry, X-ray diffraction (XRD) and transmission electron microscopy (TEM). Results demonstrated the presence of a hybrid morphology with organic polymer-encapsulated inorganic particles. Subsequently, thermogravimetric analysis (TGA) and vibrating sample magnetometry (VSM) were used to evaluate the magnetite content of the microspheres. It was found that an accordant magnetite content of about 70 wt%, could be obtained for the magnetic polymer microspheres, a value significantly higher than those reported thus far. The possible mechanism for the formation of the microspheres was proposed.     

Structural and magnetic studies of Fe2O3/SiO2 granular nanocomposites

Fe₂O₃/SiO₂ nanocomposites were synthesized by mechanical alloying, using Fe and SiO₂ powders as precursors. After 340 h milling, the sample essentially consists of hematite and amorphous silica. TEM images show hematite particles embedded in and surrounded by an amorphous silica matrix. A broad size distribution—5–50 nm—of hematite particles is found, and other group of very small—2–3 nm—unidentified particles are observed. Room temperature Mössbauer spectra show a paramagnetic doublet, which may correspond to a non-crystalline phase in the sample (probably the small unidentified particles), and a sextet corresponding to hematite. Magnetic properties were investigated by measuring hysteresis curves at different temperatures (5–300 K) and by zero-field-cooled (ZFC) and field-cooled (FC) magnetization curves (10 mT). The hysteresis loops were well fitted by a ferromagnetic contribution. No evidence of Morin transition is found down to 5 K.     

Magnetoresistance of Fe3O4/Au/Fe3O4 and Fe3O4/Au/Fe spin-valve structures

A detailed study of the in-plane magnetotransport properties of spin valves with one and two Fe₃O₄ electrodes is presented. Fe₃O₄/Au/Fe₃O₄ spin valves exhibit a clear anisotropic magnetoresistance in small magnetic fields but no giant magnetoresistance (GMR). The absence of GMR in these structures is due to simultaneous magnetization reversal in the two Fe₃O₄ layers. By contrast, a negative GMR effect is measured on Fe₃O₄/Au/Fe spin valves. The negative GMR is attributed to an electron spin scattering asymmetry at the Fe₃O₄/Au interface or an induced spin scattering asymmetry in the Au interfacial layers.     

Electrical and magnetic properties of polyaniline/Fe3O4 nanostructures

We report on electrical and magnetic properties of polyaniline (PANI) nanotubes (150 nm in diameter) and PANI/Fe₃O₄ nanowires (140 nm in diameter) containing Fe₃O₄ nanoparticles with a typical size of 12 nm. These systems were prepared by a template-free method. The conductivity of the nanostructures is 10⁻¹–10⁻² S/cm; and the temperature dependent resistivity follows a ln ρT^−1/2 law. The composites (6 and 20 wt% of Fe₃O₄) show a large negative magnetoresistance compared with that of pure PANI nanotubes and a considerably lower saturated magnetization (M_s=3.45 emu/g at 300 K and 4.21 emu/g at 4 K) compared with the values measured from bulk magnetite (M_s=84 emu/g) and pure Fe₃O₄ nanoparticles (M_s=65 emu/g). AC magnetic susceptibility was also measured. It is found that the peak position of the AC susceptibility of the nanocomposites shifts to a higher temperature (>245 K) compared with that of pure Fe₃O₄ nanoparticles (190–200 K). These results suggest that interactions between the polymer matrix and nanoparticles take place in these nanocomposites.     

Synthesis of Co-Cu-Zn doped Fe3O4 nanoparticles with tunable morphology and magnetic properties

Co-Cu-Zn doped Fe₃O₄ nanoparticles can be successfully synthesized using a simple method. The particles in the size range 20−400 nm with different regular shapes i.e. sphere-like, regular hexane and tetrahedron are controllably achieved by changing the metal ion concentration. Compared to pure Fe₃O₄ without dopants, Co-Cu-Zn doped Fe₃O₄ nanoparticles exhibit better microwave absorbing properties at 2−18 GHz. Among three Co-Cu-Zn doped Fe₃O₄ nanoparticles with different morphologies, tetrahedral Co-Cu-Zn doped Fe₃O₄ nanoparticles represent a better dielectric loss in high frequency range. This work is believed the first known report of Co-Cu-Zn doped Fe₃O₄ nanoparticles with tunable morphology and magnetic properties through the hydrothermal process without using any organic solvents, organic metal salts or surfactants.     

Synthesis and characterization of Fe3O4@C@Ag nanocomposites and their antibacterial performance

We synthesized Fe₃O₄@C@Ag nanocomposites through a combination of solvothermal, hydrothermal, and chemical redox reactions. Characterization of the resulting samples by X-ray diffraction, Fourier-transform infrared spectroscopy, field-emission scanning and transmission electron microscopy, and magnetic measurement is reported. Compared to Fe₃O₄@Ag nanocomposites, the Fe₃O₄@C@Ag nanocomposites showed enhanced antibacterial activity. The Fe₃O₄@C@Ag nanocomposites were able to almost entirely prevent growth of Escherichia coli when the concentration of Ag nanoparticles was 10 μg/mL. Antibacterial activity of the Fe₃O₄@C@Ag nanocomposites was maintained for more than 40 h at 37 °C. The intermediate carbon layer not only protects magnetic core, but also improves the dispersion and antibacterial activity of the silver nanoparticles. The magnetic core can be used to control the specific location of the antibacterial agent (via external magnetic field) and to recycle the residual silver nanoparticles. The Fe₃O₄@C@Ag nanocomposites will have potential uses in many fields as catalysts, absorbents, and bifunctional magnetic-optical materials.     

Silane treatment of Fe3O4 and its effect on the magnetic and wear properties of Fe3O4/epoxy nanocomposites

In this study, the effect of silane treatment of Fe₃O₄ on the magnetic and wear properties of Fe₃O₄/epoxy nanocomposites was investigated. Fe₃O₄ nanopowders were prepared by coprecipitation of iron(II) chloride tetrahydrate with iron(III) chloride hexahydrate, and the surfaces of Fe₃O₄ were modified with 3-aminopropyltriethoxysilane. The magnetic properties of the powders were measured on unmodified and surface-modified Fe₃O₄/epoxy nanocomposites using SQUID magnetometer. Wear tests were performed on unmodified and surface-modified Fe₃O₄/epoxy nanocomposites under the same conditions (sliding speed: 0.18 m/s, load: 20 N).The results showed that the saturation magnetization (M_s) of surface-modified Fe₃O₄/epoxy nanocomposites was approximately 110% greater than that of unmodified Fe₃O₄/epoxy nanocomposites. This showed that the specific wear rate of surface-modified Fe₃O₄/epoxy nanocomposites was lower than that of unmodified Fe₃O₄/epoxy nanocomposites. The decrease in wear rate and the increase in magnetic properties of surface-modified Fe₃O₄/epoxy nanocomposites occurred due to the improved dispersion of Fe₃O₄ into the epoxy matrix.     

Magnetic and rheological properties of monodisperse Fe3O4 nanoparticle/organic hybrid

Fe₃O₄ nanoparticle/organic hybrids were synthesized via hydrolysis using iron (III) acetylacetonate at ∼80 °C. The synthesis of Fe₃O₄ was confirmed by X-ray diffraction, selected-area diffraction, and X-ray photoelectron spectroscopy. Fe₃O₄ nanoparticles in the organic matrix had diameters ranging from 7 to 13 nm depending on the conditions of hydrolysis. The saturation magnetization of the hybrid increased with an increase in the particle size. When the hybrid contained Fe₃O₄ particles with a size of less than 10 nm, it exhibited superparamagnetic behavior. The blocking temperature of the hybrid containing Fe₃O₄ particles with a size of 7.3 nm was 200 K, and it increased to 310 K as the particle size increased to 9.1 nm. A hybrid containing Fe₃O₄ particles of size greater than 10 nm was ferrimagnetic, and underwent Verwey transition at 130 K. Under a magnetic field, a suspension of the hybrid in silicone oil revealed the magnetorheological effect. The yield stress of the fluid was dependent on the saturation magnetization of Fe₃O₄ nanoparticles in the hybrid, the strength of the magnetic field, and the amount of the hybrid.     

Preparation of superparamagnetic Fe3O4/PMMA nano composites and their magnetorheological characteristics

Fe₃O₄/PMMA composite particles were fabricated by a simple one-pot hydrothermal method. The magnetic measurement showed that the composite particles displayed a higher saturated magnetization and superparamagnetic property. The rheological properties of the magnetorheological fluids (MRFs) based on Fe₃O₄/PMMA particles were measured on a rotational rheometer with a magnetic field generator. It was found that the MRFs exhibited better MR effect and sendimentary stability than the similar materials.     

Immiscibility in the Fe3O4-FeCr2O4 spinel binary

A recent thermodynamic model of mixing in spinel binaries, based on changes in cation disordering (x) between tetrahedral and octahedral sites [Am. Mineral. 68 (1983) 18, 69 (1984) 733], is investigated for applicability to the Fe₃O₄-FeCr₂O₄ system under conditions where incomplete mixing occurs. Poor agreement with measured consolute solution temperature and solvus [N. Jb. Miner. Abh. 111 (1969) 184] is attributed to neglect of: (1) ordering of magnetic moments of cations in the tetrahedral sublattice antiparallel to the moments of those in the octahedral sublattice and (2) pair-wise electron hopping between octahedral site Fe³⁺ and Fe²⁺ ions. Disordering free energies (ΔG_D), from which free energies of mixing are calculated, are modeled by

     

Magnetic properties of prussian blue modified Fe3O4 nanocubes

Size controlled cubic Fe₃O₄ nanoparticles in the size range 90–10 nm were synthesized by varying the ferric ion concentration using the oxidation method. A bimodal size distribution was found without ferric ion concentration and the monodispersity increased with higher concentration. The saturation magnetization decreased from 90 to 62 emu/g when the particle size is reduced to 10 nm. The Fe₃O₄ nanoparticles with average particle sizes 10 and 90 nm were surface modified with prussian blue. The attachment of prussian blue with Fe₃O₄ was found to depend on the concentration of HCl and the particle size. The saturation magnetization of prussian blue modified Fe₃O₄ varied from 10 to 80 emu/g depending on the particle size. The increased tendency for the attachment of prussian blue with smaller particle size was explained based on the surface charge. The prussian blue modified magnetite nanoparticles could be used as a radiotoxin remover in detoxification applications.     

Syntheses and properties of the Fe-Co/Fe3O4 ferrites

The Fe alloy-ferrite composites Fe-Co/Fe₃O₄ are synthesized by using disproportion of Fe (II) and reduction of Co (II) by Fe⁰ in a concentrated and boiling KOH solution. The Fe alloy and ferrites are prepared in aqueous solution without any templet and surfactants at low temperature. Their structures and magnetic properties are investigated by X-ray diffractometer (XRD) and vibrating sample magnetometer (VSM). From the results of XRD, it is shown that the samples have b.c.c and f.c.c structure of Fe, and the spinel structures of the ferrite before calcinations; the samples have b.c.c and spinel structures after calcinations at 300 °C; and the samples have only f.c.c structure and the spinel structures calcined at 500 °C.     

Preparation and characterization of bifunctional, Fe3O4/ZnO nanocomposites and their use as photocatalysts

Bifunctional magnetic-optical Fe₃O₄/ZnO nanocomposites with different molar ratio were successfully synthesized by a facile two-step strategy. Compared with the other methods, it was found to be mild, inexpensive, green, convenient and efficient. Fe₃O₄ nanocrystal was used as seed for the deposit and growth of ZnO nanoparticle. A series of the characterizations manifested that the combination of Fe₃O₄ with ZnO nanoparticles was successful. Photocatalytic activity studies confirmed that as-prepared nanocomposites had excellent photodegradating behavior to Methyl Orange (MO) compared to the pure ZnO nanoparticles. The results showed that the degradation percentage of MO was about 93.6% for 1 h when the amount of catalyst was 0.51 g L⁻¹ and initial concentration of MO was 6 × 10⁻⁵ mol L⁻¹ in the pH 7 solution. Moreover, the kinetics of photocatalytic degradation reaction could be expressed by the first-order reaction kinetic model. Furthermore, the Fe₃O₄/ZnO nanocomposites could be also served as convenient recyclable photocatalysts because of their magnetic properties.     

Preparation and microwave absorption properties of Fe-phthalocyanine oligomer/Fe3O4 hybrid microspheres

The novel nano-scale Fe-phthalocyanine oligomer/Fe₃O₄ hybrid microspheres were synthesized from bis-phthalonitrile and FeCl₃·6H₂O through a simple solvent-thermal route. The morphology and structure of the hybrid microspheres were characterized by FTIR, XRD, SEM and TEM. These results showed that the hybrids were monodispersed solid microspheres and the morphology can be adjusted by controlling the addition of bis-phthalonitrile. On the basis of these results, the formation process was discussed. Magnetization measurement indicated that saturation magnetizations decreased linearly with increasing the addition of bis-phthalonitrile, while coercivities increased. The microwave absorption properties were measured by a vector network analyzer. The dielectric loss of the hybrid microspheres was larger and a new magnetic loss peak appeared at high frequency. The microwave absorbing properties enhanced with increasing the addition of bis-phthalonitrile and a maximum reflection loss of −31.1 dB was obtained at 8.6 GHz with 1 g bis-phthalonitrile when the matching thickness was 3.0 mm. The novel hybrid materials are believed to have potential applications in the microwave absorbing performances.     

Electro-precipitation of Fe3O4 nanoparticles in ethanol

The preparation of superparamagnetic magnetite (Fe₃O₄) nanoparticles by electro-precipitation in ethanol is proposed. Particle average size can be set from 4.4 to 9 nm with a standard deviation around 20%. Combination of wide-angle X-ray scattering (WAXS), Electron energy loss spectroscopy (EELS) and Mössbauer spectroscopy characterizations clearly identifies the particles as magnetite single-crystals (Fe₃O₄).     

Fabrication and characterization of magnetic Fe3O4-CNT composites

Carbon nanotubes (CNTs) decorated with magnetite nanoparticles on their external surface have been fabricated by in situ solvothermal method, which was conducted in benzene at 500 °C with ferrocene and CNTs as starting reagents. The as-prepared composites were characterized using XRD, FTIR, SEM and TEM. It has been found that the amount of magnetite nanoparticles deposited on the CNTs can be controlled by adjusting the initial mass ratio of ferrocene to CNTs. The Fe₃O₄-CNT composites display good ferromagnetic property at room temperature, with a saturation magnetization value (M_s) of 32.5 emu g⁻¹ and a coercivity (H_c) of 110 Oe.     

Synthesis of Fe3O4@LaF3:Ce,Tb nanocomposites with bright fluorescence and strong magnetism

In this paper, fluorescent-magnetic Fe₃O₄@LaF₃:Ce,Tb nanocomposites were synthesized by combining fluorescent LaF₃:Ce,Tb and magnetic Fe₃O₄ nanoparticles into new ‘two-in-one’ entities. The obtained Fe₃O₄@LaF₃:Ce,Tb nanocomposites were small (about 30 nm in diameter) and well dispersed in water. Under ultraviolet light irradiation, the Fe₃O₄@LaF₃:Ce,Tb nanocomposites emitted bright green fluorescence, and they could be easily manipulated by an external magnetic field. Such bifunctional nanocomposites may find many biomedical applications, such as cancer detection and drug delivery. And the method we used can be extended to the synthesis of other nanocomposites based on lanthanide-doped materials and metal oxides.     

Dependence of pH and surfactant effect in the synthesis of magnetite (Fe3O4) nanoparticles and its properties

Nanoparticles of Fe₃O₄ were synthesized by co-precipitation in an aqueous solution containing ferrous and ferric salts (1:2) at varying pH with ammonia as a base. It was found that the value of pH influences the reaction mechanism for the formation of Fe₃O₄. Furthermore, the addition of mercaptoethanol significantly reduced the crystalline size of Fe₃O₄ nanoparticles from 15.03 to 8.02 nm. X-ray diffraction (XRD) spectra revealed that the synthesized nanoparticles were ε-Fe₂O₃ or Fe₃O₄ phase. To further prove the composition of the product, as-prepared Fe₃O₄ were examined by X-ray photoelectron spectroscopy (XPS). Magnetic properties of the obtained particles were determined by vibrating sample magnetometer (VSM). Further analysis of the X-ray studies shows that while maintaining a pH value of 6 and 9 in a solution containing iron salts II and III ions produces ε-Fe₂O₃. Whereas a pH value of 11 produces magnetite (Fe₃O₄) phase. All of these results show that the pH has a major role in the observed phase formation of (Fe₃O₄) nanoparticles.     

Magnetic anisotropic properties in Fe3O4 and CoFe2O4 ferrite epitaxy thin films

Epitaxial thin films of Fe₃O₄ and CoFe₂O₄ on MgO (0 0 1) substrates were grown by molecular beam epitaxy at low temperature growth process. Magnetization and hysteresis loop of both films were measured to investigate magnetic anisotropic properties at various temperatures. Anomalous magnetic properties are found to be correlated with crystalline, shape, and stress anisotropies. The Fe₃O₄ film below Verwey structural transition has a change in crystal structure, thus causing many anomalous magnetic properties. Crystalline anisotropy and anomalous magnetic properties are affected substantially by Co ions. The saturation magnetization of Co–ferrite film becomes much lower than that of Fe₃O₄ film, being very different from the bulks. It indicates that the low temperature growth process could not provide enough energy to have the lowest energy state.     

Preparation and microwave absorption properties of loose nanoscale Fe3O4 spheres

Magnetite nanoparticles are found to assemble into randomly dispersed loose nanoscale spheres with diameters ∼300 nm in ethylene glycol in the presence of polyethylene and a small quantity of polyethyleneimine. Modern analysis methods are employed to provide structure information of the magnetic loose spheres. The ferromagnetic saturation magnetization is ∼80.0 emu g⁻¹, and the coercive force is 209 Oe. The microwave electromagnetic parameters are measured by a vector network analyzer. The synthesized loose spheres exhibit novel microwave properties compared with the conventional Fe₃O₄ nanoparticles. An additional microwave loss peak appears in the Ku band, which is attributed to the loose structure.