Wiedemann effect of Fe—Ga based magnetostrictive wires

(Fe83Ga17)98Cr2 wires each with a diameter of 0.7 mm are prepared by hot swaging and warm drawing from the casting rods directly,because the ductility of Fe83Ga17 alloy is improved by adding Cr element.The Wiedemann twists and dependences on magnetostrictions of Fe83Ga17 and(Fe83Ga17)98Cr2 wires are investigated.The largest observed Wiedemann twists of 245 s·cm-1 and 182 s·cm-1 are detected in the annealed Fe83Ga17 and(Fe83Ga17)98Cr2 wires,respectively.The magnetostrictions of the annealed Fe83Ga17 and(Fe83Ga17)98Cr2 wires are 160 ppm and 107 ppm,respectively.The maximum of the Wiedemann twist increases with magnetostriction increasing.However the magnetostriction is just one important factor that affects the Wiedemann effect of alloy wire,and the relationship between magnetostriction and Wiedemann effect is a complex function rather than a simple function.     

Short range order transformation and magnetostriction of Fe83Ga17 ribbons

The relationship between magnetostriction and structure of melt-spun Fe 83 Ga 17 ribbons are investigated by XRD and M¨ossbauer spectrum technique(MS).As the heat-treatment temperature increases from 650℃ to 800℃,the magnetostriction coefficient of Fe 83 Ga 17 ribbon first increases and then decreases.The largest magnetostriction coefficient(578.4 ppm) is achieved in those specimens quenched at 750℃.According to the XRD and Mo¨ssbauer spectrum analysis,a small quantity of DO 3 phase is precipitated in Fe 83 Ga 17 ribbons when quenched from 650℃ and the DO 3 phase is gradually transformed into B2-like phase if quenched at higher temperature.However,both DO 3 and B2-like phases disappear when the temperature increases up to 800℃.From this point of view,B2-like phase might be beneficial to the enhancement of magnetostrictive properties of melt-spun ribbons.     

Synthesis, structural and magnetic properties of the nanocomposite Fe63B23Nd7Y3Nb3Cr1 magnets

The Fe₆₃B₂₃Nd₇Y₃Nb₃Cr₁ nanocomposite magnets in the form of sheets have been prepared by copper mold casting technique. The phase evolution, crystal structure, microstructural and magnetic properties have been investigated in the as-cast and annealed states. The as-cast sheets show magnetically soft behaviors which become magnetically hard by thermal annealing. The optimal annealed microstructure was composed of nanosize soft magnetic α-Fe (19-29 nm) and hard magnetic Nd₂Fe₁₄B (45-55 nm) grains. The best hard magnetic properties such as intrinsic coercivity, _jH_c of 1119 kA/m, remanence, B_r of 0.44 T, magnetic induction to saturation magnetization ratio, M_r/M_s=0.61 and maximum energy product, (BH)_max of 55 kJ/m³ was obtained after annealing at 680 °C for 15 min. The annealing treatment above 680 °C results in non-ideal phase grains growth, which degrade the magnetic properties.     

Study of the magnetostrictive strains in Pr6Fe11Ga3 alloy

Magnetoelastic properties of the Pr₆Fe₁₁Ga₃ alloy are studied by magnetostriction and thermal expansion measurements. The effects of short- and long-range magnetic ordering processes about Curie temperature clearly appear in the temperature dependence of the spontaneous magnetostriction as two increasing steps with decreasing temperatures. Thermal variations of the total magnetocrystalline anisotropy introduce pronounce changes in the isofield curves of the forced magnetostriction as a negative minimum below 200 K, a compensation phenomena about 250 K, and a positive maximum between 250 K and T_c=320 K. The observed behavior of magnetostriction is discussed in terms of the competitive anisotropies of Pr and Fe sublattices and coupling magnetostrictive constants.     

Studies of the relaxed amorphous phase in the Fe80Nb6B14 alloy

The paper presents measurements of magnetic permeability, magnetic after-effects, magnetostriction, DSC and XPS for the Fe₈₀Nb₆B₁₄ amorphous alloys preliminary annealed for 1 h at temperatures ranging from 300 to 770 K. It was shown that annealing out of free volume and internal stresses causes a decrease of magnetostriction coefficient and leads to the formation of the energetically stable relaxed amorphous state. The XPS spectra show local fluctuation of boron density. This effect was attributed to the formation of small iron clusters—the characteristic feature for the relaxed amorphous phase.     

Structure and magnetic properties of melt-spun Tb0.27Dy0.73Fex ribbons

The structure and magnetic properties of the melt-spun ribbons of Tb_0.27Dy_0.73Fe_x alloy are investigated as a function of various wheel speeds during melt-quenching using a single-roll technique. It is found that Tb_0.27Dy_0.73Fe_x alloy is difficult to be fabricated as amorphous state by using the melt-quenching method. X-ray diffractions show that all these ribbons for x=1.7−2.0 are the MgCu₂-type phase at the wheel speed of 45 m s⁻¹. For Tb_0.27Dy_0.73Fe_x alloy, the high wheel speed is beneficial to eliminate the RFe₃ phase and form the perfect MgCu₂-type phase. Compared with the bulk of Tb_0.27Dy_0.73Fe_1.95, these ribbons exhibit higher intrinsic coercivity value and their saturation magnetizations increase as well. The magnetostriction of Tb_0.27Dy_0.73Fe_1.95 composite with 4% epoxy resin is 640×10⁻⁶ at 900 kA m⁻¹.     

Structure,magnetic properties and magnetostriction of Fe81Ga19 thin films

The structure, magnetic properties and magnetostriction of Fe₈₁Ga₁₉ thin films have been investigated by using X-ray diffraction analysis, scanning electron microscope (SEM), vibrating sample magnetometer and capacitive cantilever method. It was found that the grain size of as-deposited Fe₈₁Ga₁₉ thin films is 50–60 nm and the grain size increases with increase in the annealing temperature. The remanence ratio (M_r/M_s) of the thin films slowly decreases with increase in the annealing temperature. However, the coercivity of the thin films goes the opposite way with increase in the annealing temperature. A preferential orientation of the Fe₈₁Ga₁₉ thin film fabricated under an applied magnetic field exists along 〈1 0 0〉 direction due to the function of magnetic field during sputtering. An in-plane-induced anisotropy of the thin film is well formed by the applied magnetic field during the sputtering and the formation of in-plane-induced anisotropy results in 90° rotations of the magnetic domains during magnetization and in the increase of magnetostriction for the thin film.     

Magnetostriction of Fe81Ga19 oriented crystals

The effect of the orientation on the magnetostriction in Fe 81 Ga 19 alloy has been investigated experimentally and theoretically.The Fe 81 Ga 19 [001] and [110] oriented crystals were prepared and the magnetostriction was measured under different pre-stress.The saturation magnetostriction of the [001] oriented crystal increases from 170×10-6 to 330×10-6 under the pre-stress from 0 to 50 MPa.The [110] oriented crystal has a saturation magnetostriction from 20×10-6 to 140×10-6 with the compressive pre-stress from 0 to 40 MPa.The magnetostriction of [001] and [110] oriented crystals has been simulated based on the phenomenological theory.The domain rotation path has been determined and the resultant magnetostriction calculated under different pre-stress.The experimental and simulated results both show that the [001] oriented crystal exhibits better magnetostriction than [110] oriented crystal.The enhancement of the saturation magnetostriction by the compressive pre-stress in the [110] oriented crystal is higher than that in the [001] oriented crystal.     

Beneficial effect of boron on the structural and magnetostrictive behavior of Fe77Ga23 alloy

Alloys of Fe₇₇Ga₂₃B_x (x=0, 0.025, 0.050, 0.075 and 0.1) were heat treated at 1000 °C/10 h and characterized for microstructural features and magnetostriction. The study indicates that the parent alloy consists of three phases viz. A2 as the major phase and L1₂ and DO₃ as minor phases. However, the volume fraction of L1₂ and DO₃ decreases with B addition and as a result magnetostriction improves. The decrease in volume fraction of these phases is attributed to B-segregation to the grain boundary, which seems to prevent the formation of these phases. The alloy with x=0.1, however, exhibits an additional Fe₂B phase and consequently its presence leads to the re-emergence of the DO₃ phase, affecting the magnetostriction.     

The effect of different temperature annealing on phase relation of LaFe11.5Si1.5 and the magnetocaloric effects of La0.8Ce0.2Fe11.5−xCoxSi1.5 alloys

The phase relation of LaFe_11.5Si_1.5 alloys annealed at different high-temperature from 1223 K (5 h) to 1673 K (0.5 h) has been studied. The powder X-ray diffraction (XRD) patterns show that large amount of 1:13 phase begins to form in the matrix alloy consisting of α-Fe and LaFeSi phases when the annealing temperature is 1423 K. In the temperature range from 1423  to 1523 K, α-Fe and LaFeSi phases rapidly decrease to form 1:13 phase, and LaFeSi phase is rarely observed in the XRD pattern of LaFe_11.5Si_1.5 alloy annealed at 1523 K. With annealing temperature increasing from 1573  to 1673 K, the LaFeSi phase is detected again in the LaFe_11.5Si_1.5 alloy, and there is La₅Si₃ phase when the annealing temperature reaches 1673 K. There almost is no change in the XRD patterns of LaFe_11.5Si_1.5 alloys annealed at 1523 K for 3-5 h. According to this result, the La_0.8Ce_0.2Fe_11.5−xCo_xSi_1.5 (0≤×≤0.7) alloys are annealed at 1523 K (3 h). The analysis of XRD patterns shows that La_0.8Ce_0.2Fe_11.5xCo_xSi_1.5 alloys consist of the NaZn₁₃-type main phase and α-Fe impurity phase. With the increase of Co content from x=0 to 0.7, the Curie temperature T_C increases from 180 to 266 K. Because the increase of Co content can weaken the itinerant electron metamagnetic transition, the order of the magnetic transition at T_C changes from first to second-order between x=0.3 and 0.5. Although the magnetic entropy change decreases from 34.9 to 6.8 J/kg K with increasing Co concentration at a low magnetic field of 0-2 T, the thermal and magnetic hysteresis loss reduces remarkably, which is very important for the magnetic refrigerant near room temperature.     

Structural,microstructural and magnetic properties of nanocomposite isotropic Sm(CobalFe0.1MyZr0.04B0.04)7.5 ribbons with M=Ni,Cu and y=0.09 and 0.12

In boron-substituted melt-spun Sm(Co,Fe,Cu,Zr)_7.5-type alloys a nanocomposite microstructure and high coercivities in both as-spun and short-time annealed ribbons can be obtained. In the present study three different compositions, namely Sm(Co_0.73Fe_0.1Cu_0.09Zr_0.04B_0.04)_7.5, Sm(Co_0.70Fe_0.1Cu_0.12Zr_0.04B_0.04)_7.5 and Sm(Co_0.70Fe_0.1Ni_0.12Zr_0.04B_0.04)_7.5 have been examined in order to investigate the influence of composition on the magnetic properties and the microstructure. Melt-spun ribbons have been obtained and annealing has been followed under argon atmosphere for 30–75 min at 600–870 °C. For the as-spun ribbons the TbCu₇-type of structure and fcc-Co as a secondary phase have been identified in the X-ray diffraction patterns. For the annealed ribbons above 700 °C the 1:7 phase transforms into 2:17 and 1:5 phases. The TEM studies have shown a homogeneous nanocrystalline microstructure with average grain size of 30–80 nm. Coercivity values of 15–27 kOe have been obtained from hysteresis loops traced in non-saturating fields. The coercivity decreases with temperature, but it is sufficiently large to maintain values higher than 5 kOe at 380 °C.     

Crystal growth of high magnetostrictive polycrystalline Fe81Ga19 alloys

High magnetostrictive Fe₈₁Ga₁₉ alloy was prepared by induction heating zone melting method. The microstructure, solute partition behaviour, orientation evolution and magnetostriction are investigated. During the crystal growth process, the initial small grains gradually grow into large columnar crystals, and the solid-liquid interface shows slightly concave morphology. The equilibrium solute partition coefficient (k₀), effective solute partition coefficient (k_e) and solution diffusion coefficient (D) are calculated to be 0.74, 0.76 and 1.04×10⁻⁹ m²/s, respectively. In the steady growth stage, the composition distribution of the FeGa rod is uniform with average level about 18.50 at% Ga, which is close to the nominal composition. The deviation of the 〈001〉 orientation from the axial direction evolves from about 8° to 3° along the growth direction, and the corresponding magnetostriction increases from the initial 180 ppm to the final 305 ppm.     

High-throughput characterization of BixY3−xFe5O12 combinatorial thin films by magneto-optical imaging technique

Bi_xY_3−xFe₅O₁₂ thin films have been grown on GGG (Gd₃Ga₅O₁₂) (1 1 1) substrates by the combinatorial composition-spread techniques under substrate temperature (T_sub) ranging from 410 to 700 °C and O₂ pressure of 200 mTorr. In order to study the effect of substrates on the deposition of Bi_xY_3−xFe₅O₁₂ thin films, garnet substrates annealed at 1300 °C for 3 h were also used. Magneto-optical properties were characterized by our home-designed magneto-optical imaging system. From the maps of Faraday rotation angle θ_F, it was evident that the Faraday effect appears only when T_sub = 430-630 °C. θ_F reaches to the maximum value (∼6°/μm, λ = 632 nm) at 500 °C, and is proportional to the Bi contents. XRD and EPMA analyses showed that Bi ions are easier to substitute for Y sites and better crystallinity is obtained for annealed substrates than for commercial ones.     

In-situ synchrotron X-ray diffraction study of stress-induced phase transformation in Ti50.1Ni40.8Cu9.1 thin films

Stress-induced martensitic transformation of as-sputtered and post-annealed Ti_50.1Ni_40.8Cu_9.1 thin films was investigated using in-situ synchrotron X-ray diffraction (S-XRD) technique. For the as-deposited film, in-situ S-XRD analysis showed a martensitic transformation from parent phase to martensite during initial loading, followed by reorientation of martensite variants via detwinning. This detwinning process induced a strong 〈0 2 0〉 fiber texture along the loading direction and a strong 〈0 0 2〉 fiber texture perpendicular to the loading direction. For the 650 °C annealed film, there is only elastic deformation, followed by a martensitic transformation during deformation.     

Anomalous phase transformation in magnetostrictive Fe81Ga19 alloy

In this work, we have investigated the room-temperature phase constitution of heat-treated Fe₈₁Ga₁₉ alloys cooled from 800 °C at different rates. Results show that at cooling rates in the range from 0.43 to 0.26 °C/min, in addition to the A2 matrix, an fcc phase also can be observed in Fe₈₁Ga₁₉ samples at room temperature. To investigate the precipitation of the fcc phase out of A2 matrix, a systematic study of phase constitution was carried out on the samples quenched from different temperatures during cooling from 800 °C at 0.32 °C/min, which reveals an anomalous phase transformation between A2 and fcc. Precipitation of the fcc phase from A2 matrix occurs at 500 °C and its volume fraction exhibits a sharp increase at 400 °C. However, it begins to dissolve when further decreasing the temperature and only a minor fcc phase can be retained at room temperature, which suggests that the fcc phase is metastable below 400 °C. Magnetic measurements indicate that the precipitation of fcc phase deteriorates the saturation magnetization of Fe₈₁Ga₁₉.     

Effect of Cu and Ga additions on the anisotropy of R2Fe14B/α-Fe nanocomposite die-upset magnets (R=Pr,Nd)

Fully dense nanocomposite magnets containing hard R₂Fe₁₄B and soft α-Fe phases were produced from both melt-spun and mechanically milled alloys by hot pressing and subsequent die upsetting. Although R-lean R–Fe–B alloys that do not contain the grain-boundary R-rich phase are known not to be susceptible to texture development by means of die upsetting, we found that small additions of Cu make the texturing possible. The resulting microstructure of oriented platelet grains is similar to that of the R-rich die-upset magnets. Properties of the Cu-containing R₂Fe₁₄B/α-Fe die-upset magnets can be further improved by adding Ga. The anisotropic Pr₁₂Fe₈₀Cu₁Ga₁B₆ magnet made from mechanically milled alloy and containing 17.2 wt% α-Fe had a remanence of 13 kG and a maximum energy product of 23.4 MG Oe. The Pr_11.25Fe_80.75Cu₁Ga₁B₆ magnet made from melt-spun alloy and containing 16.2 wt% α-Fe had a maximum energy product of 19.9 MG Oe. The low coercivity of 3–4 kOe typical for the Cu-containing R₂Fe₁₄B/α-Fe die-upset magnets is due to the relatively coarse α-Fe grains. The latter grains are too large for intergranular exchange interaction, but, nevertheless, they are well coupled with the R₂Fe₁₄B grains by a long-range magnetostatic interaction.     

Influence of heating rate on the crystalline properties of 0.7BiFeO3-0.3PbTiO3 thin films prepared by sol-gel process

0.7BiFeO₃-0.3PbTiO₃ (BFPT7030) thin films were deposited on SiO₂/Si substrates by sol-gel process. The influence of heating rate on the crystalline properties of BFPT7030 thin films were studied by X-ray diffraction (XRD), scanning electron microscope (SEM), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). XRD patterns of the films showed that a pure perovskite phase exists in BFPT7030 films annealed by rapid thermal annealing (RTA) technique. SEM and AFM observations demonstrated that the BFPT7030 films annealed by RTA at 700 °C for 90 s with the heating rate of 1 °C s⁻¹ could show a dense, crack-free surface morphology, and the films’ grains grow better than those of the films annealed by RTA at the same temperature with other heating rates. XPS results of the films indicated that the ratio of Fe³⁺:Fe²⁺ is about 21:10 and 9:5 for the films annealed by RTA at 700 °C for 90 s with the heating rate of 1 and 20 °C s⁻¹, respectively. That means the higher the heating rate, the higher the concentration of Fe²⁺ in the BFPT7030 thin films.     

Martensitic transformation and magnetic properties of ferromagnetic shape memory Fe66Pd30Rh4 alloys

This study mainly shows that in the Fe₆₆Pd₃₀Rh₄ (at%) alloys, the L1₀ phase plays an important role in magnetostriction due to the interplay of L1₀ martensitic twins with magnetic domains. The L1₀ martensitic twin structure exhibits a strong magnetocrystalline anisotropy energy constant (K_u=1.27-2.84×10⁶ (ergs/cm³)) along the tetragonal c axis direction. In addition, the L1₀ tetragonal martensitic twin structure shows both a perfect shape memory and a reversible shape memory effect; therefore, it is expected to be applicable in magneto-mechanical applications (such as microactuators or springs). However, in this study, we discover that solution treatment (ST) and aging heat treatments of Fe₆₆Pd₃₀Rh₄ ferromagnetic shape memory alloys influence the behavior of the martensitic transition, which is associated with the change in magnetic properties. The process of a thermoelastic L1₀+L1_m twin phase decomposition→non-thermoelastic L1₀+L1_m+α_bct structure in Fe₆₆Pd₃₀Rh₄ alloys during solution treatment and aging at 400-550 °C for various times is studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The relation of phase separation morphology to the magnetic property change is examined with a superconducting quantum interference device (SQUID) magnetometer, and magnetostriction measurement is performed with a strain gage method and magnetostrictive meter setup. The results indicate that the process of martensitic transformation during aging leads to an increase in coercivity and a decrease in magnetostriction, simultaneously.     

Corrosion behavior of Nd9.4Pr0.6Febal.Co6B6Ga0.5TixCx (x=0, 1.5, 3, 6) nanocomposites annealed melt-spun ribbons

The effect of Ti and C additions on the corrosion behavior of Nd_9.4Pr_0.6Fe_bal.Co₆B₆Ga_0.5Ti_xC_x (x=0, 1.5, 3, 6) isotropic nanocomposite melt-spun ribbons in 3.5 wt% sodium chloride solution was studied. The melt-spun ribbons were annealed at 750 °C for 10 min in argon-filled quartz capsules. The microstructure of multiphase nanocrystalline samples and corrosion products was characterized using the X-ray diffraction and electron microscopy techniques. The electrochemical behavior was assessed using potentiodynamic polarization and electrochemical impedance spectroscopy. The results show that the addition of Ti and C increases the corrosion resistance of NdFeB ribbons; the best corrosion resistance was obtained for 1.5 wt% Ti and C content.     

Microstructure and hard magnetic properties in bulk rods of Nd60Fe30Al10 glass forming alloys

The Nd₆₀Fe₃₀Al₁₀ alloy exhibits a large glass forming ability which allows to obtain relatively thick cast rods containing large volume fractions of amorphous phases. In this work the microstructure and the hard magnetic properties of as-cast rods are characterized. The alloy is processed by suction casting into a chilled copper mould to obtain cylinders 5 mm diameter and 50 mm length. This diameter is selected because it is an upper limit for this processing route, beyond which the hard properties largely deteriorate. A room temperature coercivity of 0.34 T is obtained. The sample microstructure is heterogeneous, with very different size scales near the surface and along the central zone. However, in both regions a large fraction of an amorphous ferromagnetic phase is observed; it is found that paramagnetic nanocrystalline phases – mainly Nd or Nd-rich particles, embedded in the amorphous matrix – are somewhat coarser in the central zone. These larger nanocrystals, less efficient to pin domain walls, are proposed to be responsible for the lower coercive fields observed, as compared with those found in cylinders 1–3 mm diameter where no inhomogeneities are found. This conclusion is supported by microstructure, calorimetric and magnetic observations.