Structural,magnetic and electrical properties of Co1−xZnxFe2O4 synthesized by co-precipitation method

Nanoparticles of Co_1−xZn_xFe₂O₄ with stoichiometric proportion (x) varying from 0.0 to 0.6 were prepared by the chemical co-precipitation method. The samples were sintered at 600 °C for 2 h and were characterized by X-ray diffraction (XRD), low field AC magnetic susceptibility, DC electrical resistivity and dielectric constant measurements. From the analysis of XRD patterns, the nanocrystalline ferrite had been obtained at pH=12.5–13 and reaction time of 45 min. The particle size was calculated from the most intense peak (3 1 1) using the Scherrer formula. The size of precipitated particles lies within the range 12–16 nm, obtained at reaction temperature of 70 °C. The Curie temperature was obtained from AC magnetic susceptibility measurements in the range 77–850 K. It is observed that Curie temperature decreases with the increase of Zn concentration. DC electrical resistivity measurements were carried out by two-probe method from 370 to 580 K. Temperature-dependent DC electrical resistivity decreases with increase in temperature ensuring the semiconductor nature of the samples. DC electrical resistivity results are discussed in terms of polaron hopping model. Activation energy calculated from the DC electrical resistivity versus temperature for all the samples ranges from 0.658 to 0.849 eV. The drift mobility increases by increasing temperature due to decrease in DC electrical resisitivity. The dielectric constants are studied as a function of frequency in the range 100 Hz–1 MHz at room temperature. The dielectric constant decreases with increasing frequency for all the samples and follow the Maxwell–Wagner's interfacial polarization.     

Sintering temperature dependence of room temperature magnetic and dielectric properties of Co0.5Zn0.5Fe2O4 prepared using mechanically alloyed nanoparticles

Co_0.5Zn_0.5Fe₂O₄ nanoparticles were prepared using mechanical alloying (MA) and sintering. The crystallite size, coercivity, retentivity and saturation magnetization were also measured. The frequency dependence of dielectric and the magnetic parameters, namely, real permittivity ε′, loss tanget tan δ, real permeability μ′ and loss factor μ″ were measured at room temperature for samples sintered from 600 to 1000 °C, in the frequency range 10 MHz to 1.0 GHz. The results show that the crystallite size of the resulting products ranges between 16 and 67 nm for as-milled sample and the sample sintered at 1000 °C, respectively. The sample sintered at 1000 °C, measured at room temperature exhibited a saturation magnetization of 37 emu g⁻¹. The values of permittivity remain constant within the measured frequency, but vary with sintering temperature. The permeability values, on the other hand however vary with both the sintering temperature and the frequency, thus, the absolute value of the permeability decreased after the natural resonance frequency.     

Magnetic properties of xNi0.53Cu0.12Zn0.35Fe1.88O4+(1−x)BaTiO3 nanocomposites

The nanocrystalline Ni_0.53Cu_0.12Zn_0.35Fe_1.88O₄ and BaTiO₃ powders were prepared using Microwave-Hydrothermal (M-H) method at 160 °C/45 min. The as synthesized powders were characterized using the X-ray diffraction (XRD) and Transmission Electron Microscope (TEM). The size of the powders that were synthesized using M-H system was found to be ∼30 and ∼50 nm for ferrite phase and ferroelectric phases, respectively. The powders were densified using microwave sintering method at 900 °C/30 min. The ferrite and ferroelectric phases were observed from XRD and morphology of the composites was observed with the Scanning Electron Microscope (SEM).The magnetic hysteresis loops were recorded using the Vibrating Sample Magnetometer (VSM).The frequency dependence of real (μ′) and imaginary (μ″) parts of permeability was measured in the range of 1 MHz-1.8 GHz. The permeability decreases with an increase of BaTiO₃ content at 1 MHz. The transition temperature (T_C) of ferrite was found to be 245 °C. The T_C of composite materials decreases with an increase in BaTiO₃ content.     

Improvement in electrical and magnetic properties of mixed Mg-Al-Mn ferrite system synthesized by citrate precursor technique

In the present work, mixed magnesium-manganese ferrites of composition Mg_0.9Mn_0.1Al_0.3Co_zFe_1.7−zO₄ where z=0.3, 0.5 and 0.7 have been synthesized by the citrate precursor technique. X-ray diffraction patterns of the samples confirmed the formation of single-phase spinel structure. The ferrites have been investigated for their electric and magnetic properties such as dc resistivity, Curie temperature, saturation magnetization, initial permeability and relative loss factor (RLF). Fairly constant value of initial permeability over a wide frequency range (0.1-20 MHz) and low values of the relative loss factor of the order of 10⁻⁴-10⁻⁵, in the frequency range 0.1-30 MHz, are the cardinal achievements of the present investigation. In addition to this, initial permeability was found to increase with an increase in temperature while RLF was observed to be low at these temperatures. The dc resistivity and Curie temperature were found to increase with an increase in cobalt content. The mechanisms contributing to these results are discussed in detail in this paper.     

Effects of sintering temperature on grain growth and the complex permeability of Co0.2Ni0.3Zn0.5Fe2O4 material prepared using mechanically alloyed nanoparticles

Nanoparticle-sized Co_0.2Ni_0.3Zn_0.5Fe₂O₄ was prepared using mechanical alloying and sintering. The starting raw materials were milled in air and subsequently sintered at various temperatures from 600 to 1300 °C. The effects of sintering temperature on physical, magnetic and electrical characteristics were studied. The complex permittivity and permeability were investigated in the frequency range 10 MHz to 1.0 GHz. The results show that single phase Co_0.2Ni_0.3Zn_0.5Fe₂O₄ could not be formed during milling alone and therefore requires sintering. The crystallization of the ferrite sample increases with increasing sintering temperature; which decrease the porosity and increase the density, crystallite size and the shrinkage of the material. The maximum magnetization value of 83.1 emu/g was obtained for a sample sintered at 1200 °C, while both the retentivity and the coercivity decrease with increasing the sintering temperature. The permeability values vary with both the sintering temperature and the frequency and the absolute value of the permeability decreased after the natural resonance frequency. The real part of the permittivity was constant within the measured frequency, while the loss tangent values decreased gradually with increasing frequency.     

Electromagnetic properties of lithium zinc ferrites doped with aluminum

We present the results of the effect of Al substitution on the magnetic and electrical properties of Li_0.2Zn_0.6Fe_2.2−xAl_xO₄ ferrites (0.0≤x≤0.5) prepared by the standard ceramic technique. The characterization has been performed using XRD, SEM, magnetic and dielectric response in frequency. XRD analysis confirms that the system exhibits polycrystalline single phase cubic spinel structure only for low dopant content. Doping decreases the dielectric loss tangent and the ferrite conductivity in more than two orders of magnitude in the whole analyzed frequency range. Attenuation has a maximum intensity (86 dB) near 90 MHz for x=0.4. The wider bandwidth at 20 dB (94.6 MHz) is for x=0.3.     

Influence of CuO and sintering temperature on the microstructure and magnetic properties of Mg–Cu–Zn ferrites

The synthesis of a series of Mg–Cu–Zn ferrites with the substitution of Cu for Mg has been obtained by solid-state reaction method. Microstuctural and structural analyses were carried out using a scanning electron microscope and X-ray diffraction (XRD), respectively. The lattice parameter is found to increase with increasing copper content. A remarkable densification is observed with the addition of Cu ions in the ferrites. Microstructural analyses indicate that CuO influences the microstructure of the ferrites by the formation of liquid phase during sintering. The grain size significantly increases with increasing copper content. Exaggerated grain growth is observed for the samples of x=0.25–0.35. The initial magnetic permeability (μ′) increases sharply with increasing concentration of Cu ions. This increase in μ′ is explained with the grain growth mechanism and enhanced densification of the ferrites. The resonance frequency of all the samples shifts toward the lower frequency as the permeability increases with Cu content. Sintering temperature T_s also affects the densification, grain growth and initial magnetic permeability of the samples.     

Particle size distribution, magnetic permeability and dc conductivity of nano-structured and bulk LiNiZn-ferrite samples

Nanoparticles of Li_0.1(Ni_1−xZn_x)_0.8Fe_2.1O₄ (x=0-1.0) were prepared by a chemical co-precipitation method. A part of the precipitated powders was sintered at 1473 K for 2 h to obtain bulk samples via increasing the particle sizes. The particle size distribution, dc conductivity and magnetic permeability were investigated for the nano-structured samples and their bulk counterparts. The permeability as a function of temperature revealed the size effect of nano-structure in agreement with the literature. In some of the samples the permeability was almost constant over a considerable range of temperature, which may be useful in practical applications that require stability. Moreover, the nano-size structure caused a significant decrease in dc conductivity values.     

Synthesis and characterization of MnFe2O4-BiFeO3 multiferroic composites

The mixed spinel-perovskite composites of xMnFe₂O₄-(1-x)BiFeO₃ with x=0, 0.1, 0.2, 0.3 and 0.4 were prepared by solid state reaction method. The structure and grain size were examined by means of X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM), respectively. The XRD results showed that the composites consisted of spinel MnFe₂O₄ and perovskite BiFeO₃ phases after being calcined at the temperature 950 °C for 2 h. The grain size ranged from 0.8 to 1 μm. Magnetization was found to increase with increasing concentration of ferrite content. The variation of dielectric constant and dielectric loss with frequency showed dispersion in the low frequency range. Magnetocapacitance was also observed in the prepared composites, which may be the sign of magnetoelectric coupling in the synthesized composites at room temperature.     

Magnetic studies of Li-Zn ferrites prepared by citrate precursor method

Ferrites having the general formula Li_0.5−0.5xZn_xFe_2.5−0.5xO₄ where 0≤x≤0.6 in steps of 0.2 were prepared by the citrate precursor method. The Curie temperature measured shows a decrease with increasing Zn concentration. Experimental results show that the room temperature initial permeability increases with the increase in the concentration of zinc. The initial permeability has also been studied as a function of frequency in the range of 100 Hz-1 MHz. The real part of initial permeability referred as initial permeability and the imaginary part of initial permeability better known as permeability loss show dispersion with frequency. Possible mechanism contributing to the above processes is discussed.     

Dielectric properties and magnetoelectric effect of (x)NiFe2O4+(1−x)Ba0.8Sr0.2TiO3 composites

Magnetoelectric composites of NiFe₂O₄ and Ba_0.8Sr_0.2TiO₃ were prepared using conventional double-sintering ceramic method. The phase formation of magnetoelectric composites was confirmed by XRD technique. Variation of dielectric constant and loss tangent at room temperature with frequency in the range 100 Hz-1 MHz has been studied. Also the variation of dielectric constant and loss tangent with temperature and composition at fixed frequencies of 1 kHz, 10 kHz, 100 kHz and 1 MHz is reported. The static value of the magnetoelectric conversion factor was measured as a function of intensity of the magnetic field. The ME voltage coefficient of about 430 μV/cm Oe was observed for 15% NiFe₂O₄+85% Ba_0.8Sr_0.2TiO₃ composite. All the samples show linear variation of magnetoelectric conversion in the presence of static magnetic field.     

Development of nanocrystalline Mn-Zn ferrites for high frequency transformer applications

Microwave-Hydrothermal (M-H) method has been successfully used for the synthesis of nanocrystalline Mn-Zn ferrites which are used for high-frequency applications. As synthesized powders were characterized using X-ray diffraction (XRD) and transmission electron microscopy (TEM). The nanopowders were annealed at 600 °C/20 min using the microwave sintering method. The frequency dependence of dielectric constant (ε′) was measured in the range of 10 Hz-1.3 GHz and initial permeability (μ_i) was measured in the range of 10 Hz-1 MHz. The total power loss (P_t) was measured on the annealed samples at 100 kHz and 200 mT condition. Conductor-embedded-ferrite transformers were fabricated and output power (P_o), efficiency (η) and temperature rise (ΔT) were measured at sinusoidal voltage of 25 V at 1 MHz. The transformer efficiency (η) was found to be high and surface rise of temperature (ΔT) is very low.     

Permeability and electric resistivity of spin-sprayed Zn ferrite films for high-frequency device applications

By spin-spray ferrite plating, an aqueous process, we prepared Zn_xFe_3−xO₄ (0?x?0.97) films at 90 °C on polyimide and glass substrates, on which complex permeability (μ=μ′–jμ″) was measured. As Zn content x increases from 0 to 0.70 static permeability, μ_s, increases from 14 to 119, but natural resonance frequency, f_r, reduces from 1 GHz to 200 MHz. This is because magnetic anisotropy field decreases more rapidly than saturation magnetization. With increasing x DC electric resistivity, ρ, increases, exceeding 50 Ω cm (a measure of the lower limit for the high-frequency application) when x>0.15. Film with x=0.70 has relatively high μ′≈119 and μ″=0 up to 20 MHz, and is promising to be used as MHz core inductors. Film with x=0.36 has relatively high μ′=80 and μ″=0 up to 100 MHz, and it may be used as inductors at the ten MHz range and noise suppression sheets at the hundred MHz range.     

Effect of magnesium substitution on dielectric and magnetic properties of Ni-Zn ferrite

The dielectric and magnetic properties of Mg incorporated Ni-Zn spinel ferrites have been investigated. Ni_0.5−xZn_0.5Mg_xFe₂O₄ ferrites have been prepared by sol-gel auto-combustion technique. The as prepared ferrites were annealed at 673, 873 and 1073 K. The X-ray diffraction studies reveal the spinel structure of annealed ferrites. The TEM results are in agreement with XRD results. FTIR study has also been carried out to get insight into the structure of these ferrites. The dielectric measurements show that the dielectric constant (ε′), dielectric loss (tan δ) and conductivity (σ_ac) increase on incorporation of Mg in the Ni-Zn ferrite. ε′, tan δ and σ_ac also show dependence on temperature, frequency of external applied electric field and microstructure of the samples. The magnetic moment measurements reveal that the saturation magnetization (M_s) increases and coercivity (H_c) decreases with the increase in concentration of Mg²⁺ ions. M_s and H_c also show dependence on the annealing temperature.     

Magnetic, dielectric and complex impedance spectroscopic studies of nanocrystalline Cr substituted Li-ferrite

Nanocrystalline Li_0.5Fe_2.5−xCr_xO₄ (2.5≤x≥0) ferrites were prepared by a sol-gel autocombustion route. X-ray diffraction was employed to confirm the cubic spinel phase formation of the ferrites. The lattice parameter decreases with increase in Cr content. The saturation magnetization, coercivity and remanance were studied as a function of Cr content. The dielectric constant and dielectric loss were measured as a function of frequency in the frequency range 20 Hz-1 MHz. Frequency dependence of dielectric constant shows dielectric dispersion due to the Maxwell-Wagner type of interfacial polarization. In order to understand the conduction mechanism, complex impedance measurements were carried out. The substitution of chromium plays an important role in changing the dielectric and magnetic properties of lithium ferrites.     

Reentrant spin glass behavior and large initial permeability of Co0.5−xMnxZn0.5Fe2O4

A series of polycrystalline ferrites having nominal chemical composition Co_0.50−xMn_xZn_0.5Fe₂O₄ (0<x<0.4) have been synthesized by the solid-state reaction technique. The XRD analysis confirms single phase cubic spinel structure for all compositions. Lattice constant increases from 0.84195 to 0.84429 nm with the increasing Mn content and obeys Vegard's law. The average grain size increases by increasing both Mn content and sintering temperatures. Room temperature saturation magnetization increases for x=0.1 and decreases for increasing Mn content. The coercivity decreases with increasing Mn content due to the decrease of anisotropy constant. A reentrant spin glass behavior of these samples is observed from the zero field cooled magnetization measurements. The real part of the initial permeability increases by increasing both Mn content and sintering temperatures. This is due to the homogeneous grain growth and densification of the ferrites. The highest initial permeability 137 is observed for x=0.4 sintered at 1573 K on the other hand, the highest relative quality factor (2522) is obtained for the sample Co_0.2Mn_0.3Zn_0.5Fe₂O₄ sintered at 1523 K. The Mn substituted Co_0.50−xMn_xZn_0.5Fe₂O₄ ferrites showed improved magnetic properties.     

Effect of Nd substitution on structural and electrical properties of nanocrystalline zinc ferrite

Polycrystalline soft ferrite samples with general formula ZnNd_xFe_2−xO₄ (where x=0, 0.01, 0.02 and 0.03) were synthesized by oxalate co-precipitation method. The samples were characterized by XRD and SEM techniques. The single phase cubic spinel structure of all the samples was confirmed by XRD. The lattice constant and grain size of the samples are found to decrease with increase in Nd³⁺ content. Room temperature DC resistivity of the Nd³⁺ substituted zinc ferrites is 10² times higher than that of zinc ferrite. The dielectric constant (ε′) and dielectric loss (tan δ) of all the samples were measured in the frequency range 20 Hz-1 MHz. The dielectric behaviour is attributed to the Maxwell-Wagner type interfacial polarization. The dielectric loss of the samples is found to decrease with increase in Nd³⁺ content. High resistivity and low dielectric loss makes these ferrites particularly suitable for high frequency applications.     

Structure and dielectric studies of nano-composite Fe2O3: BaTiO3 prepared by sol-gel method

Nano-structure pure barium titanate (BaTiO₃) and that was doped with iron oxide (Fe₂O₃), have been prepared by sol-gel method, using barium acetate (Ba(Ac)₂) and titanium butoxide (Ti(C₄H₉O)₄), as precursors. The as-grown prepared samples by sol-gel technique were found to be amorphous, which crystallized to the tetragonal phase after synthesized at 750 °C in air for 1 h as detected from the XRD patterns. The XRD data were confirmed by transmission electron microscope (TEM). The dielectric properties namely; dielectric constant (ε′) and loss tangent (tan δ) in the frequency range between 42 Hz and 1 MHz, at range of temperature 25-250 °C were investigated. The temperature dependence of ε′ and tan δ for the undoped and doped materials, at 1 kHz, was also investigated. As a result, tan δ increased rapidly with decreasing temperature below 125 °C (Curie temperature) while above this temperature, tan δ shows temperature independent. As a result, below and above Curie temperature, ferroelectric phase and paraelectric phase of BaTiO₃ can be obtained, respectively.     

Suitability of water based magnetic fluid with CoFe2O4 particles in hyperthermia

Magnetic susceptibility of the magnetic fluid with CoFe₂O₄ particles was measured in the low-frequency range in order to determine mean values of the magnetic grain size and the saturation magnetisation. The volume concentration of the solid phase (CoFe₂O₄) was also found. Results of the calorimetric measurements, in the range from 70 kHz to 1.7 MHz, confirmed the suitability of use of the medium studied in magnetic fluid hyperthermia, especially in the frequency region 600–800 kHz. The H²–law-type dependence of the specific absorption rate on the square amplitude of the magnetic field testified to the presence of superparamagnetic particles in the magnetic fluid. The minimum magnetic field intensity needed for successful hyperthermal treatment was experimentally determined.     

Effect of Pr doping on magnetic and dielectric properties of Ni-Zn ferrites by “one-step synthesis”

Pr³⁺-doped Ni-Zn ferrites with a nominal composition of Ni_0.5Zn_0.5Pr_xFe_2−xO₄ (where x=0-0.08) were prepared by a one-step synthesis. The magnetic and dielectric properties of the as-prepared Ni-Zn ferrites were investigated. X-ray diffraction data indicated that, after doping, all samples consisted of the main spinel phase in combination of a small amount of a foreign PrFeO₃ phase. The lattice constants of the ferrites initially increased after Pr³⁺ doping, but then became smaller with additional Pr³⁺ doping. The addition of Pr³⁺ resulted in a reduction of grain size and an increase of density and densification of the as-prepared samples. Magnetic measurement revealed that the saturation magnetization of the as-prepared ferrites, M_s, decreased, while the coercivity, H_c, increased with increasing substitution level, x, and the Curie temperature, T_c, kept a rather high value, fluctuating between 308 and 320 °C. Both the real and imaginary parts of permeability of the ferrites decreased slightly after Pr³⁺ doping. However, the natural resonance frequency shifted towards higher frequency from 13.07 to 36.17 MHz after the addition of Pr³⁺, driving the magnetic permeability to much higher frequency, reaching the highest value (36.17 MHz) when x=0.04. Introduction of Pr³⁺ ions into the Ni-Zn ferrite reduced the values of the dielectric loss tangent, especially in the frequency range of 1-400 MHz. However, the magnitude of dielectric loss of the samples doped with different amounts of Pr³⁺ raised little.