Tailoring of structural, electrical and magnetic properties of BaCo2 W-type hexaferrites by doping with Zr-Mn binary mixtures for useful applications

Single-phase W-type hexaferrite, BaCo₂Fe_16−2x(ZrMn)_xO₂₇ (x=0.0-1.0), has been synthesized by the chemical co-precipitation technique. Mössbauer analysis indicates substitution of Zr ions on tetrahedral (4e and 4f_IV) sites and Mn ions on the octahedral ‘4f_VI site’ at low-doped concentration when the concentration is increased Mn ions but show preference for the octahedral ‘2b site’. The highest enhancement in the value of the room temperature resistivity of 2.82×10⁹ Ω cm has been obtained by doping with Zr-Mn content of x=0.6. The dissipation factor increases from 6.49×10³ to 9.97×10³ at 10 kHz with the addition of Zr-Mn dopants. Such materials are potentially suitable for electromagnetic attenuation purposes, for microwave absorption and as radar absorbing material. High values of saturation magnetization (67 emu/g) and remanent magnetization (34.7 emu/g) are obtained for substitution level of x=0.4 making them suitable for data processing devices.     

Improved electrical,magnetic and dielectric properties of polypyrol (PPy) substituted spinel ferrite composites

CoTb_0.03Fe_1.97O₄ ferrite and poypyrrole (PPy) polymer nano composites were prepared by mixing the nano crystalline ferrite with poypyrrole (PPy) by following the solid state reaction synthesis route. The XRD patterns of CoTb_0.03Fe_1.97O₄ spinel ferrite powders and polymer (PPy) exhibited single phase spinel structure. The amorphous nature of PPy was evidenced by the broad peaks of XRD patterns. The surface morphology unfolded heterogeneous distribution in composites and ferrite. The grains in ferrite were spherical in shape with clear boundaries. The morphology was appreciably altered by the inclusion of ferrite contents. The higher activation energy and resistivity aroused due to blocking of conduction mechanism owing to nanoparticles embedded in the PPy matrix. A downfall in the dielectric loss of the composites is observed as the frequency of the applied field is increased. The incorporation of ferrite contents optimized the magnetic parameters of the composites. The enhanced coercivity (Hc) of these nanocomposites might be beneficial for memory devices.     

Structural,electrical and magnetic properties of (Fe,Co) co-doped SnO2 diluted magnetic semiconductor nanostructures

Nanostructures (NSs) of basic composition Sn_1−xFe_x/2Co_x/2O₂ with x=0.00, 0.04, 0.06, 0.08 and 0.1 were synthesized by citrate-gel route and characterized to understand their structural, electrical and magnetic properties. X-ray diffraction and Raman spectroscopy were used to confirm the formation of single phase rutile type tetragonal structure. The crystallite sizes calculated by using Williamson Hall were found to decrease with increasing doping level. In addition to the fundamental Raman peaks of rutile SnO₂, the other three weak Raman peaks at about 505, 537 and 688 cm⁻¹ were also observed. Field emission scanning electron microscopy studies showed the emergence of structural transformation. Electric properties such as dc electrical resistivity as a function of temperature and ac conductivity as a function of frequency were also studied. The variation of dielectric properties with frequency reveals that the dispersion is due to Maxwell–Wagner type of interfacial polarization in general. Hysteresis loops were clearly observed in M–H curves of Fe and Co co-doped SnO₂ NSs. However, pure SnO₂ nanoparticles (NPs) showed paramagnetic behaviour which vanished at higher values of magnetic field. The grain and grain boundary contribution in the conduction process is estimated through complex impedance plot fitted with non-linear least square (NLLS) approach which shows that the role of grain boundaries increases rapidly as compared to the grain volume with the increase of Fe and Co ions in to system.     

Electromagnetic properties and microwave absorption of W-type hexagonal ferrites doped with La

W-type barium hexaferrites with compositions of Ba₁Co_0.9Zn_1.1Fe₁₆O₂₇ and Ba_0.8La_0.2Co_0.9Zn_1.1Fe₁₆O₂₇ were synthesized by the sol-gel method. The electromagnetic properties and microwave absorption behavior of these two ferrites were studied in the 2-18 GHz frequency range. The microstructure and morphology of the ferrites were characterized by X-ray diffraction (XRD), and scanning electron microscopy (SEM) techniques. The complex permittivity spectra, the complex permeability spectra and microwave reflection loss were measured by a microwave vector network analyzer. The XRD patterns show that the main phase of the Co₂W ferrite forms without other intermediate phases when calcined at 1200 °C. The SEM images indicate that flake-like hexagonal crystals distribute uniformly in the materials. Both the magnetic and dielectric losses are significantly enhanced by partial substitution of La³⁺ for Ba²⁺ in the W-type barium hexaferrites. The microwave absorption property of the La³⁺ doping W-type hexaferrite sample is enhanced with the bandwidth below −10 dB around 8 GHz and the peak value of reflection loss about −39.6 dB at the layer thickness of 2 mm.     

The role of Ga substitution on magnetic and electromagnetic properties of nano-sized W-type hexagonal ferrites

A series of nano-sized single phase W-type SrGa_xZn₂Fe_16?xO₂₇ (x = 0.0, 0.1, 0.2, 0.3, 0.4) hexaferrites prepared by sol gel technique and sintered at 950 °C have been investigated. The thermal decomposition behavior of nitrate–citrate gel of as prepared powder was investigated by means of DTA/TGA analysis. The sintered powders were characterized by FTIR, XRD, SEM, VSM and vector network analyzer (VNA). X-ray diffraction patterns for pure and substituted W-type hexaferrites show the single phase structure with no impurity phase. The lattice parameters (a and c) decrease with the increase of Ga contents (x). The grain size estimated from SEM images is in the range of 139–76 nm which confirms the nanocrystalline nature of the investigated samples. The saturation magnetization (M_s) decreases whereas coercivity (H_c) increases with the increase of Ga contents (x). The values of H_c for all of the investigated samples lie in the range of few hundred oersteds which is one of the necessary conditions for EM materials. The microwave absorption property is enhanced in the frequency (with respect to ?20 dB) from 0.5 to 13 GHz, and the bandwidth reaches 0.899 GHz. The attenuation peak value is ?32 dB at the matching thickness of 3.4 mm.     

Influence of annealing temperature on the formation, microstructure and magnetic properties of spinel nanocrystalline cobalt ferrites

Nanocrystalline cobalt ferrites were synthesized by a simple, general, one-step sol–gel auto-combustion method. An interpretation based on the measurement of the adiabatic flame temperature and the amounts of gas evolved during reaction had been proposed for the nature of combustion. The influence of annealing temperatures on the magnetic properties was investigated. The microstructure was characterized by means of X-ray diffractometer (XRD) and transmission electron microscopy (TEM). It was found that the particle size and magnetic properties of the as-prepared ferrite samples showed strong dependence on the annealing temperature. The coercivity initially increased and then decreased with increasing annealing temperature whereas the particle size and saturation magnetization continuously increased.     

Influence of rare-earth ions on the structure and magnetic properties of barium W-type hexaferrite

Barium W-type hexaferrite with composition Ba_0.95R_0.05Mg_0.5Zn_0.5CoFe₁₆O₂₇ where R=Y, Er, Ho, Sm, Nd, Gd, and Ce ions has been prepared by the double-sintering ceramic technique. Structure of the prepared samples has been characterized by the X-ray diffraction (XRD) technique. The XRD patterns at room temperature show the presence of secondary phase with the intensity of the secondary phase increasing with increasing ionic radius of the rare earth (RE) ions. The variation of the magnetic susceptibility (χ_M) with temperature in the range 300–750 K at different magnetic field intensities (1280, 1733 and 2160 Oe) was studied by using Faraday's method. The results show that the Curie temperature (T_C) increases regularly with increasing RE ionic radius then decreases again, after which it reaches maximum value at Sm ion of radius ≈1.04 Å. This behavior was explained on the basis of the changes in Fe³⁺–O–Fe³⁺ superexchange interaction. The effective magnetic moment μ_eff. of the investigated samples was discussed in view of varying the RE element as well as the magnetization of different sublattices.     

Magnetic properties of rare earth ion (Sm) added nanocrystalline Mg-Cd ferrites, prepared by oxalate co-precipitation method

Nanocrystalline ferrite powder having the general formula Mg_1−xCd_xFe₂O₄+5% Sm³⁺ (x=0, 0.2, 0.4, 0.6, 0.8 and 1.0) was synthesized by chemical oxalate co-precipitation technique. The synthesized powder was characterized by X-ray, IR and SEM techniques. The XRD analysis confirms cubic spinel phase with orthoferrite secondary phase. The lattice constant increases with increase in Cd²⁺ content (x). It is smaller than that for pure Mg-Cd ferrites. The average crystallite size lies in the range 28.69-32.66 nm. Saturation magnetization and magnetic moment increase with cadmium content up to x=0.4 and decrease thereafter. This is attributed to the existence of localized canted spin. The decrease in saturation magnetization and magnetic moment beyond x=0.4 is due to the presence of triangular spin arrangement on B-site. Coercivity and remanent magnetization decrease while Y-K angles increase with Cd²⁺ content. The Sm³⁺ addition improves the magnetic properties.     

Microstructure and magnetic characterization of the Sm-CoMn co-substituted SrCaM hexagonal ferrites

A series of Sm-CoMn substituted hexagonal ferrites with chemical composition of Sr_0.85-xCa_0.15Sm_xFe_12-y(Co_0.5Mn_0.5)_yO₁₉ (0.00?≤?x?≤?0.60, (0.00?≤?y?≤?0.50) were synthesized by the solid-state reaction method. Microstructure and magnetic properties of the hexaferrites have been investigated by the X-ray diffraction, field emission scanning electron microscopy and a permanent magnetic measuring system. A single magnetoplumbite phase is exhibited in the hexaferrites with the substitutiom of Sm (0.00?≤?x?≤?0.12) and CoMn (0.00?≤?y?≤?0.10) contents. For the hexaferrites containing Sm (x?≥?0.24) and CoMn (y?≥?0.20), impurity phases are observed in the structure. The FESEM micrographs exhibit that the hexaferrites with different Sm-CoMn contents have formed hexagonal structures and the grain size of the hexaferrites remains unchanged with increasing Sm-CoMn content. The remanence (B_r), H_k/H_cj ratios, and maximum energy product [(BH)_max] decrease with increasing Sm-CoMn content (0.00?≤?x?≤?0.60, (0.00?≤?y?≤?0.50). Instrinsic coercivity (H_cj) and magnetic induction coercivity (H_cb) increase with increasing Sm-CoMn content (0.00?≤?x?≤?0.12, 0.00?≤?y?≤?0.10), and then decrease with increasing Sm-CoMn content (0.12?≤?x?≤?0.36, 0.10?≤?y?≤?0.30), while for the hexaferrites with Sm (x?≥?0.36) and CoMn (y?≥?0.30), with increasing Sm-CoMn content, H_cj increases and H_cb decreases.     

Structure and magnetic properties of Ni0.5Zn0.5Mn0.5-xMoxFe1.5O4 ferrites prepared by sol-gel auto-combustion method

A series of Mo doped Ni-Mn-Zn ferrites compounds with the formula Ni_0.5Zn_0.5Mn_0.5-xMo_xFe_1.5O₄ (x = 0, 0.025, 0.05, 0.075 and 0.1) were first synthesized by sol-gel auto-combustion method. The X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), and vibrating sample magnetometer (VSM) analysis were carried out to characterize the microstructural and magnetic properties of ferrites. Rietveld refinement of X-ray diffraction data confirmed the formation of cubic spinel structure and the emergence of FeMoO₄ phase with the substitution of Mo⁶⁺ contents. The grain size increased remarkably due to the formation of the liquid phase. The saturation magnetization (M_s) increased while the coercivity (H_c) decreased from 67.3 to 12.1 Oe due to the decrease of magneto-crystalline anisotropy constant. The initial permeability (μ_i) increased significantly from 34 (x = 0) to 114 (x = 0.075) and later decreased for x = 0.1. In our experiment, Ni_0.5Zn_0.5Mn_0.425Mo_0.075Fe_1.5O₄ ferrite presented the best microstructure and soft magnetic properties.     

The role of Mg substitution on the microstructure and magnetic properties of Ba Co Zn W-type hexagonal ferrites

A series of W-type hexagonal ferrites with the composition BaCoZn_1−xMg_xFe₁₆O₂₇ (0?x?0.6) were prepared by the conventional ceramic method to study their structural and magnetic properties as a function of temperature and composition. The characterization using X-ray diffraction indicated that a hexagonal W-type single-phase structure and the effect of composition on the unit cell parameters, density and porosity was studied. The variation of the magnetic susceptibility (χ_M) with temperature for all the investigated samples in the temperature range (300–800 K) shows three regions of behavior that was explained on the basis of the distribution of Zn²⁺ and Mg²⁺ ions in the lattice and leads to the anomalous behavior of the effective magnetic moment μ_eff. The Curie temperature indicated that the critical concentration is at x=0.5. Paramagnetic nature of the samples above the Curie temperature is observed. The Curie Weiss constant θ calculated from the plot of 1/χ_M vs. T (K) is in agreement with the expected value. The effective magnetic moment μ_eff decreases with increasing the intensity of magnetic field. The possible mechanisms contributing to these properties are discussed in the text.     

Effect of annealing temperature on the structural, photoluminescence and magnetic properties of sol-gel derived Magnetoplumbite-type (M-type) hexagonal strontium ferrite

Magnetoplumbite-type (M-type) hexagonal strontium ferrite particles were synthesized via sol-gel technique employing ethylene glycol as the gel precursor at two different calcination temperatures (800 and 1000 °C). Structural properties were systematically investigated via X-ray diffraction (XRD), field emission scanning electron microscopy, high resolution transmission electron microscopy (HRTEM), energy dispersive spectroscopy (EDS), thermogravimetric analysis (TGA), photoluminescence spectrophotometry and superconducting quantum interference device magnetometer. XRD results showed that the sample synthesized at 1000 °C was of single-phase with a space group of P6₃/mmc and lattice cell parameter values of a=5.882 Å and c=23.048 Å. EDS confirmed the composition of strontium ferrite calcined at 1000 °C being mainly of M-type SrFe₁₂O₁₉ with HRTEM micrographs confirming the ferrites exhibiting M-type long range ordering along the c-axis of the crystal structure. The photoluminescence (PL) property of strontium ferrite was examined at excitation wavelengths of 260 and 270 nm with significant PL emission peaks centered at 350 nm being detected. Strontium ferrite annealed at higher temperature (1000 °C) was found to have grown into larger particle size, having higher content of oxygen vacancies and exhibited 83-85% more intense PL. Both the as-prepared strontium ferrites exhibited significant oxygen vacancies defect structures, which were verified via TGA. Higher calcination temperature turned strontium ferrite into a softer ferrite.     

Densification and magnetic properties of low-fire NiCuZn ferrites

The mixing of (Ni_0.38Cu_0.12Zn_0.50)Fe₂O₄ powders with Bi₂O₃ was performed using the solid-state mixing as well as wet chemical coating processes such as ammonia precipitation coating, urea precipitation coating, and solution coating. Ferrites prepared from the wet chemical coating processes could be densified at a lower sintering temperature without significant impact on the microstructural evolution compared with that prepared by solid-state mixing. In addition, samples prepared from the wet chemical coating process have a higher B_r and B_s and a lower H_c compared with that from solid-state mixing. Considering both the effects of sintering temperature and sintered density (>95% T.D.), ferrites with 1.5 wt% Bi₂O₃ addition by ammonia precipitation coating sintered at 900°C can provide the best permeability and quality factor (191 and 68.2, respectively) among all the cases studied.     

Structural and magnetic properties of cadmium substituted Ni-Al ferrites

Nickel Cadmium Aluminum Ferrites with the general formula Ni_1−xCd_xAl_0.6Fe_1.4O₄ where x=0, 0.25, 0.50 and 0.75 were prepared through standard double sintering reaction method. The crystallography, surface morphology and magnetic properties were studied by X-ray diffractometer (XRD), Scanning Electron Microscope (SEM) and Vibrating Sample Magnetometer (VSM), respectively. The expected single phase spinel structure was confirmed by XRD analysis. Lattice parameter and X-ray density were increased monotonically by increasing Cd concentration due to the larger ionic radii of the cadmium ion. Surface topography of the samples consists of fine cubical shape microstructures. The average grain size increased with increase in cadmium concentration. The saturation magnetization was found to be increased with increase in cadmium content up to x=0.50 and then decreased with further increasing cadmium concentration for x=0.75.     

Optical properties of blue emitting Ce activated XMg2Al16O27 (X = Ba, Sr) phosphors

Here we reported that the optical properties of novel blue-emitting Ce³⁺ activated XMg₂Al₁₆O₂₇ (X = Ba, Sr) phosphors were prepared by combustion method successfully. The excitation spectrum shows a broad band extending from 280 to 380 nm, centered at 355 nm, and the emission spectrum shows intense blue emission broad band centering at 441 nm for Ba²⁺ and Sr²⁺ host lattices. XRD pattern indicates crystalline nature of prepared phosphors. SEM analysis shows morphology of the ternary-hexaaluminate based phosphor prepared by combustion method. The Ce³⁺ activated XMg₂Al₁₆O₂₇ (X = Ba, Sr) should be a promising blue phosphor for near ultraviolet-based white-light-emitting diodes.     

稀土元素La掺杂BaFe12O19微结构和磁性能的研究术

用固相法制备了镧掺杂M型钡铁氧体（Ba1--xLaxFel2O19,x=0．0-0．6）,针对不同取代量与不同温度的烧结,研究取代量和温度对钡铁氧体微结构和磁性能的影响．在烧结温度为1100-1175℃,当X=0．0-0．6时,样品主要有单一的六角M型钡铁氧体相构成．SEM表明,La离子的加入不会影响钡铁氧体微观形貌．在磁性能方面,随着La离子的增加,钡铁氧体的饱和磁化强度先增加后减小,矫顽力逐渐增加．在同一取代量下,钡铁氧体的饱和磁化强度随烧结温度升高呈现上升趋势,矫顽力随着烧结温度的升高而降低．饱和磁化强度在x=0．2,烧结温度1175℃时达到最大值62．8emu／g,矫顽力在x=0．6,烧结温度1125℃时达到最大值3911．5Oe．     

Influence of sintering time on structural,magnetic and electrical properties of Si–Ca added Sr-hexa ferrites

Sr-hexa ferrites with the addition of Si (0.5 wt%) and Ca (0.5 wt%) have been prepared by solid-state reaction method with sintering time variation ranging from 2 to 10 h. The structural characterization of the samples confirmed the major phase of Sr-hexa ferrite. Average grain size was found within the range of 1–4 μm. Vicker hardness increased from 512 to 1187H_v. The coercivity and remanence had the ranges from 596 to 4255 Oe and 324 to 516 G, respectively. The DC electrical resistivity measurements were carried out by two-probe method as a function of temperature from 303 to 723 K. The room temperature DC resistivity increased from 1.67×10⁶ to 2.89×10⁸ Ω cm in turn the activation energy also increased from 0.314 to 0.495 eV. The DC electrical resistivity decreased while drift mobility increased with the rise in temperature, ensuring the semi-conducting behavior. Dielectric properties were studied as a function of frequency in the range of 80 Hz to 1 MHz at room temperature.     

Structural, magnetic and electrical properties of NiCuZn ferrites prepared by microwave sintering method suitable for MLCI applications

Polycrystalline NiCuZn soft ferrites with stoichiometric iron were prepared by a novel microwave sintering method. The powders were calcined, compacted and sintered at 950 °C for 30 min in a microwave sintering furnace. X-ray diffraction patterns confirm the formation of single phase cubic spinel structure. The grain size was estimated using SEM micrographs. The lattice constant is found to increase with increase in zinc concentration. The sintered ferrites have been investigated for their physical, magnetic and electrical properties such as bulk density, X-ray density, porosity, anisotropy constant, initial permeability, saturation magnetization, DC resistivity, dielectric constant and dielectric loss as a function of zinc concentration. Permeability, saturation magnetization, dielectric constant and dielectric loss were found to increase while DC resistivity was found to decrease with the replacement of Zn with Ni. The present series of ferrites are found to posses properties that are suitable for the core materials in multilayer chip inductors.     

Effect of annealing on phase composition,structural and magnetic properties of Sm-Co based nanomagnetic material synthesized by sol-gel process

Sm-Co based nanomagnetic material was synthesized by means of a Pechini-type sol-gel process. In this method, a suitable gel-precursor was prepared using respective metal salts and complexing agent such as citric acid. The gel-precursor was dried at 300 °C and then subjected to various reductive annealing temperatures: 350, 500 and 600 °C. The nanopowders so obtained were characterized for their structure, phase composition and magnetic properties. FT-IR studies on the gel-precursor showed the binding of metal cations with the citrate molecules in the form of metal-citrate complex. The gel-precursor, which was annealed at 350 °C showed the presence of both meta-stable cobalt carbide (Co₂C, Co₃C) and Co₃O₄ phases; while the sample annealed at 500 °C indicated the sign of SmCo₅ phase. Upon increasing the reductive annealing temperature to 600 °C, crystalline phase such as fcc-Co and Sm₂C₃ were formed prominently. FE-SEM analysis revealed the change in sample morphology from spherical to oblate spheres upon increasing the annealing temperature. VSM measurements demonstrated ferromagnetic nature at room temperature for all the nanopowders obtained irrespective of their after reductive annealing temperature.