Effect of Sr concentration on microstructure and magnetic properties of (Ba1−xSrx)(Ti0.3Fe0.7)O3 ceramics

Fe-doped (Ba_1−xSr_x)TiO₃ ceramics were prepared by solid-state reaction, and ferromagnetism was realized at room temperature. The microstructure and magnetism were modified by the Sr concentration control (0≤x≤75 at%) at a fixed Fe concentration, and the relevant magnetic exchange mechanism was discussed. All the samples are shown to have a single perovskite structure. When increasing the Sr concentration, the phase structure is transformed from a hexagonal perovskite into a cubic perovskite, with a monotonic decrease in lattice parameters induced by ionic size effect. The room-temperature ferromagnetism is expected to originate from the super-exchange interactions between Fe³⁺ on pentahedral and octahedral Ti sites mediated by the O²⁻ ions. The increase in Sr addition modifies two main influencing factors in magnetic properties: the ratio of pentahedral to octahedral Fe³⁺ and the concentration of oxygen vacancies, leading to a gradually enhanced saturation magnetization. The highest value, obtained for Fe-doped (Ba_0.25Sr_0.75)TiO₃, is an order of magnitude higher than that of the Fe-doped BaTiO₃ system with similar Fe concentration and preparation conditions, which may indicate (Ba_1−xSr_x)TiO₃ as a more suitable matrix material for multiferroic research.     

Electromagnetic and microwave absorbing properties of Co2Z-type hexaferrites doped with La

Z-type ferrites doped with La³⁺, Ba_3−xLa_xCo₂Fe₂₄O₄₁ (x=0.00-0.30), were prepared by sol-gel method. The effect of the substitution La³⁺ rare-earth ions for Ba²⁺ ions on the microstructure, complex permeability, permittivity and microwave absorption of the samples was investigated. The results show that the major phase of the ferrites changed to Z-phase when sintering temperature was 1250 °C for 5 h. With the increase of the substitution ratio of La³⁺ ions from 0.0 to 0.3, the lattice parameters a and c increased gradually, which resulted in the change of the particle shape and size. The data of magnetism showed that the addition of La³⁺ ions make the ferrite a better soft magnetic material due to increase of magnetization (σ_s) and decrease of coercivity (H_c). The La³⁺ ions doped in the ferrite not only improved complex permeability and complex permittivity, but also microwave absorbency.     

Magnetic and dielectric properties of alkaline earth Ca and Ba ions co-doped BiFeO3 nanoparticles

Ca²⁺ and Ba²⁺ ions co-doped BiFeO₃ nanoparticles, Bi_0.8Ca_0.2−xBa_xFeO₃ (x=0-0.20), were prepared by a sol-gel method. The phase structure, grain size, dielectric and magnetic properties of the prepared samples were investigated. The results showed that the lattice structure of the nanoparticles transformed from rhombohedral (x=0) to orthorhombic (x=0.07-0.19) and then to tetragonal (x=0.20) with x increased. The dielectric properties of the nanoparticles were affected by the properties of the substitutional ions as well as the crystalline structure of the samples. The magnetic properties of the nanoparticles were greatly improved and the T_N of the nanoparticles was obviously increased. All the Ca²⁺ and Ba²⁺ ions co-doped BiFeO₃ nanoparticles presented the high ratio of M_r/M from 0.527 to 0.571 and large coercivity from 4.335 to 5.163 KOe.     

High temperature ferromagnetism of the vacuum-annealed (In1−xFex)2O3 powders

(In_1−xFe_x)₂O₃ (x = 0.02, 0.05, 0.2) powders were prepared by a solid state reaction method and a vacuum annealing process. A systematic study was done on the structural and magnetic properties of (In_1−xFe_x)₂O₃ powders as a function of Fe concentration and annealing temperature. The X-ray diffraction and high-resolution transmission electron microscopy results confirmed that there were not any Fe or Fe oxide secondary phases in vacuum-annealed (In_1−xFe_x)₂O₃ samples and the Fe element was incorporated into the indium oxide lattice by substituting the position of indium atoms. The X-ray photoelectron spectroscopy revealed that both Fe²⁺ and Fe³⁺ ions existed in the samples. Magnetic measurements indicated that all samples were ferromagnetic with the magnetic moment of 0.49-1.73 μ_B/Fe and the Curie temperature around 783 K. The appearance of ferromagnetism was attributed to the ferromagnetic coupling of Fe²⁺ and Fe³⁺ ions via an electron trapped in a bridging oxygen vacancy.     

The synthesis and the magnetic properties of Gd-doped FexCo1−x/CoyFe3−yO4 micro-octahedrons composites

Gd³⁺-substituted micro-octahedron composites (Fe_xCo_1−x/Co_yGd_zFe_3−y−zO₄) in which the Fe-Co alloy has either a bcc or fcc structure and the oxide is a spinel phase were fabricated by the hydrothermal method. The X-ray diffraction (XRD) patterns indicate that the as-synthesized Gd³⁺-substituted micro-octahedron composites are well crystallized. Scanning electron microscopy (SEM) images show that the final product consists of larger numbers of micro-octahedrons with the size ranging from 1.3 to 5 μm, and the size of products are increased with increasing the concentration of KOH. The effect of the Co²⁺/Fe²⁺ ratio (0?Co²⁺/Fe²⁺?1) and substitution Fe³⁺ ions by Gd³⁺ ions on structure, magnetic properties of the micro-octahedrons composites were investigated, and a possible growth mechanism is suggested to explain the formation of micro-octahedrons composites. The magnetic properties of the structure show the maximal saturation magnetization (107 emu/g) and the maximal coercivity (1192 Oe) detected by a vibrating sample magnetometer.     

Room-temperature ferromagnetism in Sn1−xMnxO2 nanocrystalline thin films prepared by ultrasonic spray pyrolysis

Sn_1−xMn_xO₂ (x=0.01-0.05) thin films were synthesized on quartz substrate using an inexpensive ultrasonic spray pyrolysis technique. The influence of doping concentration and substrate temperature on structural and magnetic properties of Sn_1−xMn_xO₂ thin films was systematically investigated. X-ray diffraction (XRD) studies of these films reflect that the Mn³⁺ ions have substituted Sn⁴⁺ ions without changing the tetragonal rutile structure of pure SnO₂. A linear increase in c-axis lattice constant has been observed with corresponding increase in Mn concentration. No impurity phase was detected in XRD patterns even after doping 5 at% of Mn. A systematic change in magnetic behavior from ferromagnetic to paramagnetic was observed with increase in substrate temperature from 500 to 700 °C for Sn_1−xMn_xO₂ (x=0.01) films. Magnetic studies reveal room-temperature ferromagnetism (RTFM) with 3.61×10⁻⁴ emu saturation magnetization and 92 Oe coercivity in case of Sn_1−xMn_xO₂ (x=0.01) films deposited at 500 °C. However, paramagnetic behavior was observed for the films deposited at a higher substrate temperature of 700 °C. The presence of room-temperature ferromagnetism in these films was observed to have an intrinsic origin and could be obtained by controlling the substrate temperature and Mn doping concentration.     

Structure and magnetic properties of melt-spun Tb0.27Dy0.73Fex ribbons

The structure and magnetic properties of the melt-spun ribbons of Tb_0.27Dy_0.73Fe_x alloy are investigated as a function of various wheel speeds during melt-quenching using a single-roll technique. It is found that Tb_0.27Dy_0.73Fe_x alloy is difficult to be fabricated as amorphous state by using the melt-quenching method. X-ray diffractions show that all these ribbons for x=1.7−2.0 are the MgCu₂-type phase at the wheel speed of 45 m s⁻¹. For Tb_0.27Dy_0.73Fe_x alloy, the high wheel speed is beneficial to eliminate the RFe₃ phase and form the perfect MgCu₂-type phase. Compared with the bulk of Tb_0.27Dy_0.73Fe_1.95, these ribbons exhibit higher intrinsic coercivity value and their saturation magnetizations increase as well. The magnetostriction of Tb_0.27Dy_0.73Fe_1.95 composite with 4% epoxy resin is 640×10⁻⁶ at 900 kA m⁻¹.     

Magnetic properties enhancement of Nd2Fe14B/α-Fe nanocomposites by Ta substitution

Nanostructured Nd_9.5Fe_84−xB_6.5Ta_x (x=0, 0.5, 1, 1.5, and 2) ribbons composed of Nd₂Fe₁₄B and α-Fe phases with a high coercivity and maximum energy product are fabricated by direct melt spinning. The effects of Ta addition on the structures and magnetic properties of melt-spun Nd_9.5Fe_84−xB_6.5Ta_x (x=0, 0.5, 1, 1.5, and 2) ribbons have been investigated. Compared with addition-free ribbons, small addition of Ta is found to reduce the grain sizes of the samples and improve their magnetic properties due to a strong exchange coupling between the Nd₂Fe₁₄B hard phase and α-Fe soft phase. A coercive field of 750 kA/m and a maximum energy product of 158 kJ/m³ in melt-spun Nd_9.5Fe_82.5B_6.5Ta_1.5 ribbons are obtained at room temperature.     

Synthesis and magnetic properties of La-substituted M-type Sr hexaferrites

Single-phase M-type hexagonal ferrites Sr_1−xLa_xFe₁₂O₁₉ (0≤x≤1) were prepared by a ceramic route. The stability limits of the ferrite phases were determined with a combination of various microscopy techniques, electron-probe micro-analysis, powder X-ray diffraction and thermal analysis. SrFe₁₂O₁₉ (x=0) is stable up to 1420 °C, whereas LaFe₁₂O₁₉ (x=1) exists between 1360 and 1400 °C only. The lattice parameters of Sr_1−xLa_xFe₁₂O₁₉ exhibit a linear variation with x, i.e. a₀ slightly increases and c₀ decreases with x, leading to a decrease of the unit cell volume with x. The saturation magnetization at T=5 K decreases with increasing La concentration. Room temperature Mössbauer analysis shows that the Fe³⁺/Fe²⁺ valence change occurs in the 2a sites for the whole composition range.     

Effect of Mn on the magnetic properties of Fe3B/Nd2Fe14B nanocomposites

The magnetic properties of Nd_4.5Fe_77−xMn_xB_18.5 (x=0, 1 and 2) nanocomposites prepared by the crystallization of amorphous precursors were investigated. Addition of Mn is found to decrease the crystallization temperature of the amorphous ribbons. The intrinsic coercivity _iH_c and maximum energy product (BH)_max increase from 2.6 kOe and 9.1 MGOe for x=0 to 3.1 kOe and 10.3 MGOe for x=1, respectively, and the remanence ratio M_r/M_s increases from 0.70 to 0.72. The effect of Mn on Curie temperature T_C and the thermal stability of M_r and _iH_c were also studied. ⁵⁷Fe Mössbauer spectra have been recorded for x=0, 1 and 2 ribbons at room temperature and site preference of the Mn atoms in Fe₃B and Nd₂Fe₁₄B phases is discussed using the Mössbauer spectroscopy.     

Effects of In-substitution on the structure and magnetic properties of multi-doped YIG ferrites with low saturation magnetizations

Multi-doped YIG ferrites {Y_1.7Gd_0.5Ca_0.8}[Fe_2−xIn_x](Fe_2.15V_0.4Mn_0.05Al_0.4)O₁₂ (x=0, 0.3, 0.6, 0.7, 0.8 and 0.9) with low saturation magnetizations (4πM_s=400-600 G at 298 K) were prepared by a conventional ceramic technology and the effects of In³⁺-substitution on their structures and magnetic properties were systematically investigated using XRD, SEM and VSM. It has been found that as-synthesized powders and sintered ferrites showed a single-phase of garnet structure with a cell parameter (a) that increased linearly with increase in In³⁺ concentration from x=0 up to 0.9. Apparent relative densities of sintered samples were all over 98%, but no remarkable influences of In³⁺-substitution were observed by SEM on the refinement of crystal grains and the enhancement of sintering of ferrites. In addition, the Curie temperature T_c decreased almost linearly as In³⁺concentration increased, while the corresponding saturation magnetization at room temperature presented a variation characterized by a gradual increase first and then a rapid plunge. On the basis of quantitative analysis of XRD data and the theory on super-exchange interactions, it has been established that the incorporated In³⁺ ions via doping were exclusively located at the sites with octahedral coordinations in the crystal structure and the aforementioned magnetic properties can be simply attributed to weakening super-exchange interactions between neighboring magnetic ions through oxygen ions due to the “dilution effect” of added non-magnetic In³⁺ ions.     

纳米结构CoxFe3-xO4多孔微球的磁性及交换偏置效应研究

用乙二醇为溶剂,用三氯化铁、二氯化钴和醋酸铵为起始反应试剂,通过溶剂热反应首次合成了纳米结构Co_xFe_3-xO₄多孔微球.用X射线衍射仪(XRD)、透射电子显微镜(TEM)和扫描电子显微镜(SEM)表征样品的结构和形貌,结果表明,所制备的单分散Co_xFe_3-xO₄多孔微球为立方多晶结构,其直径约300 nm,是由约30 关键词： xFe_3-xO₄')" href="#">Co_xFe_3-xO₄ 多孔微球 磁性 交换偏置效应     

Relationship between structural and magnetic properties in (Ti,Fe)O2 powders obtained by mechanical milling

Fe-doped TiO₂ samples with different Fe content were prepared by mechanical alloying starting from TiO₂ rutile and FeO. The samples were structurally and magnetically characterized by XRD, Mössbauer spectroscopy, X-ray absorption spectroscopy (XAS), AC-susceptibility and magnetization measurements. XAS results showed that Fe ions were incorporated into the rutile phase with oxygen coordination that was lower than that expected in this phase. The oxygen coordination number decreased with the increase of Fe²⁺ ions such as it was previously found in the milled samples of TiO₂ doped with hematite. The RT Mössbauer spectra were reproduced using two paramagnetic interactions, one corresponding to Fe²⁺ (δ∼0.87 mm/s) and the other to Fe³⁺ (δ∼0.31 mm/s). Magnetometry measurements showed the presence of paramagnetic and ferromagnetic-like interactions at room temperature. Although saturation and coercivity of the ferromagnetic phase increased with iron, the effective magnetic moment per iron atom decreased, probably due to the precipitation of Fe rich antiferromagnetic structures.     

Effect of Fe/Sr mole ratios on the formation and magnetic properties of SrFe12O19 microtubules prepared by sol-gel method

The sol was obtained by sol-gel method. Then, the sol was dripped onto the absorbent cotton template. The gel was obtained after the evaporation of water. Strontium ferrite microtubules were prepared after carrying out calcination process at different temperatures. The phase, morphology and particle diameter and the magnetic properties of samples were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM), respectively. The effects of Fe³⁺/Sr²⁺ mole ratio and calcination temperature on the crystal structure, morphology and magnetic properties of ferrite microtubules were studied. The external diameters of obtained SrFe₁₂O₁₉ microtubules were found to range between 8 and 13 μm; the wall thicknesses ranged between 1 and 2 μm. When the Fe³⁺/Sr²⁺ mole ratio and the calcination temperature were 11.5 and 850 °C, respectively, the coercivity, saturation magnetization and remanent magnetization for the samples were 7115.1 Oe, 70.1 and 42.4 emu/g, respectively. The mechanism of the formation and variation in magnetic properties of the microtubules were explained.     

Particle analysis and properties of mechanically alloyed Nd16Fe76−xTixB8

Nanocrystalline Nd₁₆Fe_76−xTi_xB₈ hard magnetic powders were prepared by mechanical alloying and respective heat treatment at 973–1073 K /30–60 min. The nanocrystalline hard magnetic powders were investigated by the NanoSight Halo LM10^TM Nanoparticle Analysis System, AFM, SEM and Mössbauer spectrometry. The nanocrystals have average size of 40 nm and the crystals form agglomerates with an average size of about 180 nm. Halo^TM, AFM and SEM techniques are the complementary methods, which give comparable results.     

Hard magnetic properties in Pr2Fe14B/α-Fe nanocomposite magnets with a combined addition of V and C

Nanostructured Pr₈Fe_86−xV_xB_6−yC_y (x=0, 1; y=0, 1) ribbons composed of Pr₂Fe₁₄B and α-Fe phases with a high coercivity are fabricated by direct melt spinning. The effects of a single addition of V and a combined addition of V and C on the structures and magnetic properties of melt-spun Pr₈Fe₈₆VB_6−xC_x (x=0 and 1) ribbons have been investigated. Compared with addition-free ribbons, 1 at% V addition is found to reduce the grain sizes of the samples and improve their magnetic properties due to a strong exchange coupling between the hard and the soft phase. A remanence ratio of 0.82, a coercive field of 6.2 kOe and a maximum energy product of 23.4 MGOe in melt-spun Pr₈Fe₈₅VB₆ ribbons are obtained at room temperature. The combined addition of V and C is found to lead to the formation of an intermediate phase of VC at grain boundaries, which appears as a pinning barrier during magnetization and results in an increase of the coercivity value to 6.9 kOe for melt-spun Pr₈Fe₈₅VB₅C ribbons.     

发光二极管用红色荧光粉Sr0.8-xBaxEu0.2WO4的制备和性质研究

采用化学共沉淀法制备了不同Ba²⁺掺杂浓度、 不同煅烧温度的Sr_0.8-xBa_xEu_0.2WO₄红色荧光粉. 研究了样品的晶体取向和晶格 畸变对发光性质的影响, 实验结果表明: 合成的Sr_0.8-xBa_xEu_0.2WO₄红色荧光粉为四方相, 样品中Eu³⁺的⁵D₀–⁷F₂跃迁的红光能被近紫外光和蓝光有效激发. 适量的Ba²⁺离子取代部分的Sr²⁺提高了Sr_0.8Eu_0.2WO₄荧光粉的发光强度, Ba²⁺掺杂浓度的改变对基质的晶格参数、晶体对称性和发光性能影响较大, Ba²⁺的最佳掺杂量为30%.     

Influence of boron on the giant magnetocaloric effect of La(Fe0.9Si0.1)13

The influences of boron addition on the phase formation, Curie temperature and magnetic entropy change of the NaZn₁₃-type La(Fe_0.9Si_0.1)₁₃ compound have been investigated. Eight boron containing La(Fe_0.9Si_0.1)₁₃B_x samples were prepared with x=0, 0.03, 0.06, 0.1, 0.2, 0.3, 0.5 and 0.6, respectively. Experimental results show that a small amount of B addition in La(Fe_0.9Si_0.1)₁₃ forms the solid solution NaZn₁₃-type structure phase by substituting B for Si or doping B into interstitial position of the lattice, preserves its giant magnetocaloric effects due to their first-order structural/magnetic transition, as well as increase its Curie temperature T_c slightly. The maximum magnetic entropy changes in the magnetic field change of 0–1.6 T are around 20 J kg^–1 K^–1 for the samples with Boron addition less than 0.3, while improving the Curie temperatures by 2 K.     

The magnetoelectric coupling in rhombohedral–tetragonal phases coexisted Bi0.84Ba0.20FeO3

Ba doped Bi_1.04−xBa_xFeO₃ ceramics with x up to 0.30 have been prepared by the tartaric acid modified sol–gel method. The X ray diffraction patterns show that the structure transforms from rhombohedral to tetragonal with increasing the Ba substitution concentration from 10% to 30% and the coexistence of distorted rhombohedral and tetragonal phases in 20% Ba substituted BiFeO₃, which was further confirmed by the Raman spectra. Bi_0.84Ba_0.20FeO₃ exhibits the highest magnetization (1.6 emu/g under magnetic field of 12 kOe) compared with the other samples of different Ba substitution concentration. Significant enhancement of the ferroelectricity has been observed in 20% and 30% Ba substituted BiFeO₃ with saturate polarization close to 6.6 μC/cm² for Bi_0.74Ba_0.30FeO₃. The magnetoelectric coupling of Bi_0.84Ba_0.20FeO₃ has been measured and the maximum decrease of magnetization under magnetic field of 9.8 kOe was about 0.06 emu/g with increasing applied electric field to 11 kV/cm, and the magnetoelectric coefficient is 1.5×10⁻¹² s/m.     

Magnetic and Microwave Absorbing Properties of Electrospun Ba(1−x)LaxFe12O19 Nanofibers

Ba_(1−x)La_xFe₁₂O₁₉ (0.00≤x≤0.10) nanofibers were fabricated via the electrospinning technique followed by heat treatment at different temperatures for 2 h. Various characterization methods including scanning electron microscopy (SEM), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and microwave vector network analyzer were employed to investigate the morphologies, crystalline phases, magnetic properties, and complex electromagnetic parameters of nanofibers. The SEM images indicate that samples with various values of x are of a continuous fiber-like morphology with an average diameter of 110±20 nm. The XRD patterns show that the main phase is M-type barium hexaferrite without other impurity phases when calcined at 1100 °C. The VSM results show that coercive force (H_c) decreases first and then increases, while saturation magnetization (M_s) reveals an increase at first and then decreases with La³⁺ ions content increase. Both the magnetic and dielectric losses are significantly enhanced by partial substitution of La³⁺ for Ba²⁺ in the M-type barium hexaferrites. The microwave absorption performance of Ba_0.95La_0.05Fe₁₂O₁₉ nanofibers gets significant improvement: The bandwidth below −10 dB expands from 0 GHz to 12.6 GHz, and the peak value of reflection loss decreases from −9.65 dB to −23.02 dB with the layer thickness of 2.0 mm.