钯纳米线制备的研究进展

钯纳米线在一些特殊领域表现出了独特的应用价值.本文介绍了基于模板法、阶边修饰法和自组装法等制备钯纳米线的一些方法,并对其进展和应用前景进行展望.     

ZnO纳米线的电化学制备研究

High-quality ZnO nanowires have been synthesized at relatively low temperature via one-step electrochemical anodization technique. In this method, Zn sheet acted as the anode and Pb sheet served as the counter electrode, and the complex solution of HF-C₂H₅OH-H₂O was used as electrolyte. ZnO nanowires were characterized by Field Emission Scanning Electron Microscopy (FE-SEM), Transmission Electron Microscopy (TEM) and Selected Area Electron Diffraction (SAED) and X-ray Diffraction (XRD). The results show that the nanowires were wurtzite crystalline ZnO, and the ZnO nanowires with the diameters of 70 nm and 30～40 nm were obtained by adjusting preparation conditions, respectively.     

钯纳米线电极的制备及其应用于乙醇的电化学氧化研究

纳米线作为纳米科学领域中的重要一员,因其优异的光学、电学及磁学等特性引起了凝聚态物理学界、化学界以及材料科学界科学家们的极大关注,并己成为当今纳米科技研究的热点领域[1].纳米线的制备方法有多种,本文提及的模板法制备纳米线结构技术是20世纪90年代初发展起来的一种既经济又简便实用的新工艺[2].     

基于DNA为模板的铂纳米线的电化学制备

基于DNA为模板的铂纳米线的电化学制备;铂纳米线;电化学还原;DNA模板     

SiO-Au法制备硅纳米线

在低真空的CVD系统中直接热蒸发SiO粉末并以金为催化剂在硅衬底上制备出大量长达几十微米的硅纳米线(SiNWs), 通过X 射线衍射谱(XRD)、场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)、选区电子衍射仪(SAED)和Raman光谱等技术对硅纳米线进行形貌及结构分析. 实验结果表明, 在不同生长温度下制备得到的硅纳米线质量不同, 其中在700 ℃温区生长的硅线质量最好; 与晶体硅Raman的一级散射特征峰(TO)520.3 cm−1相比, 纳米硅线的Raman特征峰(TO)红移至514.8 cm−1.     

导电聚吡咯纳米线的电化学无模板法可控合成与表征

以β-萘磺酸(NSA)为掺杂剂,采用电化学无模板法制备了聚吡咯(PPy)纳米线.研究了NSA浓度、吡咯(Py)单体浓度及反应温度对PPy纳米线形貌的影响.分别采用场发射扫描电子显微镜(FE-SEM)和拉曼光谱对PPy纳米线的结构形貌和化学结构进行了表征.结果表明,利用电化学无模板法可得到中空的PPy纳米线;NSA浓度会影响PPy纳米线的取向性;增大Py单体浓度,可制得圆锥状PPy纳米线;低温有利于合成形状细长、紧密堆积的PPy纳米线.PPy纳米线形貌受游离Py浓度及Py-NSA胶束数量影响,通过调节NSA浓度、Py浓度及反应温度改变游离Py浓度及Py-NSA胶束数量,可制得不同形貌的PPy纳米线.     

溶胶凝胶模板法制备羟基磷灰石纳米线

以氯化钙和五氧化二磷的醇溶液为前驱体溶液,多孔阳极氧化铝(AAO)膜为模板,通过溶胶凝胶-模板法成功制备出羟基磷灰石(Ca10(PO4)6(OH)2,HAP)纳米线;利用扫描电镜、能量色散谱仪、透射电镜、X射线衍射仪及傅立叶变换红外光谱仪等分析了产物的组成和微结构;并讨论了纳米线的生长机理.结果表明,所制备的羟基磷灰石纳米线直径约为50nm、长度达20μm,分别与模板的孔径和厚度一致.     

TiO2纳米管与纳米线的制备及光电化学研究

利用钛箔表面沉积一层TiO2纳米粒子作为晶种,与NaOH反应,通过改变反应温度制备了TiO2纳米管与纳米线.在170℃,48 h的条件下合成了TiO2纳米管.在180℃时得到另一种一维的TiO2纳米线.并用XRD,SEM,SAED,EDS及HRTEM等分析手段对两种产物的成分、形貌、结构进行表征.对TiO2纳米管电极的光电化学性能进行了研究.结果表明,TiO2纳米管与纳米线为锐钛矿型和金红石型的混晶结构.TiO2纳米管单色光的光电转化效率达到10.38%.与钛酸盐纳米管相比,混晶结构TiO2纳米管显示出优良的光电转化性能.     

利用溶液法制备小分子有机化合物纳米线

利用溶液法制备得到以乳酸分子为主要组分的纳米线.通过FESEM、TEM、EDX、TGA和FT-IR等手段对得到的纳米线样品进行了表征.并对纳米线形成的各种影响因素和机理进行了初步讨论.结果表明,锌离子的存在是乳酸纳米线得以形成的重要条件.     

聚苯胺纳米线修饰的DNA电化学传感器的研究

采用电流密度递减的方法在玻碳电极表面修饰聚苯胺纳米线(PAINW), 以SEM对其形貌进行表征, 测得PAINW的尖端直径在80～100 nm之间. 以乙基-(3-二甲基丙基)碳化二亚胺盐酸盐(EDC)为偶联活化剂, 将5'-磷酸基修饰的寡聚核苷酸片断共价固定在聚苯胺修饰的电极上, 一定条件下, 以亚甲基蓝为电化学杂交指示剂, 采用差分脉冲伏安法对杂交信号进行检测, 实现了对特定序列DNA片段的互补、非互补序列的识别.     

钯镍合金在玻碳电极上电结晶机理

在钯镍合金电解液中, 采用循环伏安和计时安培实验方法, 运用Scharifker和Hills模型、Heerman和Tarallo模型揭示钯镍合金的成核机理. 结果表明, 钯镍合金在玻碳电极上发生成核过程. Scharifker和Hills模型分析表明, 钯镍合金更符合扩散控制下的三维生长的连续成核机理. 借助于Heerman和Tarallo模型, 拟合得到钯镍合金的成核和生长的动力学参数. 拟合结果显示, 电位阶跃从-0.85 V负移至-0.92 V (vs SCE), 钯镍合金在玻碳电极上的成核速率从0.83 s^-1增加到7.71 s^-1, 成核密度数从2.77×10⁴ cm^-2提高至7.09×10⁴ cm^-2.     

钯镍合金薄膜电极上甲酸电氧化-去合金化效应

在含PdC l2、N iSO4和乙二胺的弱碱性镀液中,于Au电极上用恒电位电沉积Pd-N i合金薄膜,后经酸性溶液中循环伏安法处理,得到去合金化的Pd-N i电极.扫描电镜以及电化学测试表明,去合金化处理使Pd-N i镀膜表面微观粗糙度增加,比表面积增大;ICP-AES和XPS分析证实合金表层N i的优先溶出造成Pd的富集.去合金化处理的Pd-N i电极电催化氧化甲酸的活性明显优于未处理的Pd-N i电极和多晶Pd电极.     

脉冲电沉积Pd-Ni合金纳米颗粒及其甲酸电催化氧化

采用方波脉冲方法,在钯镍合金电解液中成功地电化学沉积出镍原子含量分别为12.0%、16.4%和22.6%的钯镍合金纳米颗粒. 钯镍合金纳米颗粒为球状,粒径50 ~ 80 nm. 随钯镍合金生长电位负移,合金的镍含量提高,其纳米颗粒大小基本相似但纳米颗粒数目增多,交联度提高和真实活性面积增大. 钯镍合金纳米颗粒镍含量提高,在硫酸溶液中其氢弱吸附峰电流增大. 钯镍合金纳米颗粒电极的甲酸电催化氧化活性较好,随合金纳米颗粒的镍含量提高和交联度增加,合金纳米颗粒电极的甲酸电催化氧化稳定性更高.     

模板法制备枝状Pt纳米线

一维纳米材料的制备是近年来纳米材料的研究热点. 利用具有纳米尺度的孔洞阵列模板沉积各种材料构筑纳米线的方法具有制备简便和成本较低等优点[1,2]. 常用的模板有多孔阳极氧化铝(AAO)、多孔硅和聚合物等, 其中AAO模板具有耐高温, 绝缘性好, 孔洞分布均匀, 孔径、孔深大小可控等特点, 是模板法研究的热点. 通过模板法电化学沉积制备各种金属纳米线已有很多报道[3～8], 本研究小组也曾报道了模板法电化学沉积Au等纳米线的制备及性质[9～12], 但用该方法制备的金属纳米线都为单一的线状结构. 组成当代大规模集成电路的基本器件一般具有3个或3个以上的电极. 单一的线状结构纳米线, 不能满足纳米电子学对纳米材料和纳米器件性能研究的需要. 在纳米器件的特性研究和探索中, 枝状或Y形纳米结的制备有重要的意义, 它是纳米器件从理论到实用化的必备条件. Sui等[13]用模板法成功制备了枝状碳纳米管, 但用AAO模板制备枝状金属纳米线的研究至今还未见报道. 本文通过控制铝片的阳极氧化条件, 先制备出具有分枝状孔洞结构的AAO模板, 再用电化学法沉积金属Pt, 实现了枝状Pt纳米线的可控生长. 这对其它金属枝状纳米线的制备以及进一步掺杂、构筑纳米原型器件等具有显著的实用价值.     

Synthesis and Magnetic Property of Fe-B Amorphous Alloy Nanowires by Inducing DC Magnetic Field

One dimension (1D) Fe-B amorphous alloy nanowires with diameter of 50-80 nm and length of several micrometers were synthesized under weak DC (direct current) magnetic field by KBH₄ reducing in aqueous solution. The structure, composition, and morphology were characterized by X-ray diffraction (XRD), inductively coupled plasma atomic emission spectrometry (ICP-AES), and scanning electron microscope (SEM), respectively. The results revealed that the magnetic field led to the fabrication of Fe-B amorphous alloy nanowire structure. Vibrating sample magnetometer (VSM) has been used to detect the magnetic properties of the samples. The results showed that the inducing of magnetic field had obvious effect on the magnetic properties of the samples.     

磁场诱导制备Fe-B非晶态合金纳米线及其磁学性质

通过引入外加直流电磁场, 采用KBH4还原法在室温下制备了一维Fe-B非晶态合金纳米线, 并采用X射线衍射(XRD)、电感耦合等离子原子发射光谱仪(ICP-AES)和扫描电子显微镜(SEM)等表征方法研究了产物的结构、组成和形貌. 结果表明, 在直流电磁场的作用下得到了Fe-B非晶态合金纳米线, 所得样品的直径在50-80 nm之间, 长度达到数微米. 通过振动样品磁强计(VSM)研究其磁学性质, 发现外加磁场的引入会显著影响Fe-B非晶态合金的磁学性质. 随着引入磁场强度的增强, 所得样品的饱和磁感应强度和矫顽力明显区别于未引入磁场制备的Fe-B非晶态合金.     

Luminescence Property and Synthesis of Sulfur-doped ZnO Nanowires by Electrochemical Deposition

"Sulfur-doped zinc oxide (ZnO) nanowires were successfully synthesized by an electric field-assisted electrochemical deposition in porous anodized aluminum oxide template at room temperature. The structure, morphology, chemical composition and photoluminescence properties of the as-synthesized ZnO:S nanostructures were investigated. X-ray diffraction and the selected area electron diffraction results reveal that the as-ynthesized products are single phase with hexagonal wurtzite structure with a highly preferential orientation in the (101) direction. Transmission electron microscopy observations indicate that the nanowires are niform with an average diameter of 70 nm and length up to several tens of micrometers. X-ray photoelectron pectroscopy further reveals the presence of S in the ZnO nanowires. Room-temperature photoluminescences observed in the sulfur-doped ZnO nanowires which exhibits strong near-band-edge ultraviolet peaks at 378 and 392 nm and weak green emissions at 533 and 507 nm. A blue emission at 456 nm and violet emissions at around 406, 420, and 434 nm were also observed in the PL spectrum for the as-synthesized ZnO:S nanowires. The PL spectrum shows that S-doping had an obvious effect on the luminescence property of typical ZnO nanowires."     

Electrochemical Reversible Reforming between Ethylamine and Acetonitrile on Heterostructured Pd-Ni(OH)2 Nanosheets

Rational design of electrocatalysts is essential to achieve desirable performance of electrochemical synthesis process. Heterostructured catalysts have thus attracted widespread attention due to their multifunctional intrinsic properties, and diverse catalytic applications with corresponding outstanding activities. Here, we report an in situ restoration strategy for the synthesis of ultrathin Pd-Ni(OH)₂ nanosheets. Such Pd-Ni(OH)₂ nanosheets exhibit excellent activity and selectivity towards reversible electrochemical reforming of ethylamine and acetonitrile. In the acetonitrile reduction process, Pd acts as reaction center, while Ni(OH)₂ provide proton hydrogen through promoting the dissociation of water. Also ethylamine oxidation process can be achieved on the surface of the heterostructured nanosheets with abundant Ni(II) defects. More importantly, an electrolytic cell driven by solar cells was successfully constructed to realize ethylamine-acetonitrile reversible reforming. This work demonstrates the importance of heterostructure engineering in the rational synthesis of multifunctional catalysts towards electrochemical synthesis of fine chemicals.     

Controlled Synthesis of Se/Te Alloy and Te Nanowires

"Se/Te alloy and Te nanowires (NWs) with different morphologies were synthesized through a novel, control-lable solution-phase method. Sodium dodecylbenzene sulfonate was employed as a surfactant to control the reaction rate in the synthesis. Through reaction process dynamics control, both "bending" and "V-shaped" Se/Te alloy NWs were controllably produced. The phase structures and morphologies of the Se/Te and Te products were investigated with XRD, TEM, and HRTEM. The formation mechanisms of the NWs were investigated on the basis of the experimental results. The significance of these results lies in the important implications concerning the potential use of these NWs materials for nanoscale electronic devices."