ToF-SIMS investigation of octadecylphosphonic acid monolayers on a mica substrate

In this paper, time-of-flight secondary ion mass spectrometry (ToF-SIMS) under static conditions was used to investigate self-assembled monolayers (SAMs) of octadecylphosphonic acid (OPA) formed on freshly cleaved muscovite mica substrates. The coverage of OPA on mica ranged from 20 to 100%, with a film thickness of 1.7+/-0.2 nm, which was determined by atomic force microscopy (AFM) imaging. The relative intensity of the specific secondary ion species associated with the OPA and with the exposed mica substrate exhibited good correlation with surface coverage. An excellent correlation was also observed (R2=0.98) between the relative SIMS [OPA-H]- intensity and the surface carbon concentration (OPA C 1s, in atomic %) from XPS at the prescribed surface coverage. The observation of positive and negative OPA molecular attachment of secondary ions involving the substrate species is discussed in terms of the chemical affinity of the OPA phosphonate headgroup for the cleaved mica surface as well as the sampling depth. In addition, the OPA molecular attachment species formed with the potassium ions on the cleaved mica substrate dominated the positive secondary ion mass spectrum in the high-mass range. A temperature-dependent, ToF-SIMS study employing in situ heating of a 100% coverage OPA monolayer revealed that the molecules begin to diffuse above approximately 80 degrees C, resulting in a decrease in the relative secondary ion yield of the OPA-specific secondary ions. This observation is hypothesized to be due to a decrease in the effective coverage of the substrate by the OPA molecules, which in turn could be due to the formation of multilayers upon heating in an effort to minimize the energy of the system. The interesting behavior of the novel OPA dimer species as a function of temperature is also reported. It was observed that the relative intensity of OPA and the mica-specific secondary ion peak intensities to that of Si (mica substrate) provides an effective means to estimate the change in coverage at elevated temperatures.     

Delivering octadecylphosphonic acid self-assembled monolayers on a Si wafer and other oxide surfaces

We describe a simple experimental approach for delivering self-assembled monolayers (SAMs) of octadecylphosphonic acid (OPA) on many oxide surfaces using a nonpolar medium with a dielectric constant around 4 (e.g., trichloroethylene). This approach readily results in the formation of full-coverage OPA SAMs on a wide variety of oxide surfaces including cleaved mica, Si wafer, quartz, and aluminum. Especially, the availability of delivering full-coverage OPA SAM on a Si wafer is unique, as no OPA SAMs at all could be formed on a Si wafer when using a polar OPA solution. The reason a nonpolar solvent is superior lies in the very fact that the hydrophilic OPA headgroup tends to escape from the nonpolar solution and is thus enriched at the medium-air interface. It is these OPA headgroups seeking a hydrophilic surface that make possible the well-controlled OPA monolayer on an oxide surface.     

Interaction of water with self-assembled monolayers of alkylsilanes on mica

The interaction of water with self-assembled alkylsilane monolayers on mica substrates has been studied using an atomic force microscope operated in contact, noncontact, and electrical polarization modes. Complete monolayer films were found to be effective in blocking water adsorption. On partially covered surfaces water was found to produce large changes in the conductivity and surface potential of the exposed mica regions. It was also found that water could penetrate films near defects and at island edges.     

High-energy electron beam lithography of octadecylphosphonic acid monolayers on aluminum

Monolayers of octadecylphosphonic acid were self-assembled on silicon substrates sputter coated with aluminum. Patterning of the self-assembled monolayer was achieved by high-energy electron (50 kV) illumination using an electron beam lithography tool. The change in chemical composition of the exposed monolayer was investigated by time-of-flight secondary ion mass spectrometry over an area of 100 x 100 microm2. The electron dose required to fully expose the SAM was found to be about 6 mC/cm2. Gratings were exposed with line widths from 10 microm to 100 nm. The resulting patterns were imaged using friction force microscopy. It was found that the minimum line width is limited to ca. 100 nm by the patterning resolution. The pattern resolution achieved, ca. 40 nm, is equal to the grain size of the sputter-coated aluminum layer, and the possibility that the grain size limits the pattern resolution is discussed.     

Electrochemically deposited palladium as a substrate for self-assembled monolayers

The vast majority of reports of self-assembled monolayers (SAMs) on metals focus on the use of gold. However, other metals, such as palladium, platinum, and silver offer advantages over gold as a substrate. In this work, palladium is electrochemically deposited from PdCl2 solutions on glassy carbon electrodes to form a substrate for alkanethiol SAMs. The conditions for deposition are optimized with respect to the electrolyte, pH, and electrochemical parameters. The palladium surfaces have been characterized by scanning electron microscopy (SEM) and the surface roughness has been estimated by chronocoulometry. SAMs of alkane thiols have been formed on the palladium surfaces, and their ability to suppress a Faradaic process is used as an indication for palladium coverage on the glassy carbon. The morphology of the Pd deposit as characterized by SEM and the blocking behavior of the SAM formed on deposited Pd delivers a consistent picture of the Pd surface. It has been clearly demonstrated that, via selection of experimental conditions for the electrochemical deposition, the morphology of the palladium surface and its ability to support SAMs can be controlled. The work will be applied to create a mixed monolayer of metals, which can subsequently be used to create a mixed SAM of a biocomponent and an alkanethiol for biosensing applications.     

Reactivity of acid fluoride-terminated self-assembled monolayers on gold

This report describes the reactivity of acid fluoride (AF)-terminated self-assembled monolayers (SAMs) on gold toward amine and alcohol compounds and the potentiality of AF as a reactive intermediate for surface functionalizations. The AF group was generated in situ on a gold surface by reacting the terminal carboxylic acid group in the SAM of 16-mercaptohexadecanoic acid with cyanuric fluoride and pyridine under the optimized conditions. AF was found to be highly reactive toward various amine groups, such as primary and secondary amines, but it did not react effectively with alcohol. In addition, the amide coupling reaction by microcontact printing (microCP) was compared with the solution-based reaction: when amine-derivatized ferrocene compound was used for 1-min microCP on the AF-activated surface, the surface coverage of the reaction product was about 83% of 3.45 x 1014 cm-2, the coverage obtained in the solution-based reaction. On the basis of the high reaction efficiency of microCP, the AF-activated surface was also used as a platform for patterning a biological ligand, biotin.     

Temperature-dependent formation of octadecylsiloxane self-assembled monolayers on mica as studied by atomic force microscopy

We have investigated the growth of octadecylsiloxane (ODS) self-assembled monolayers on mica. Freshly cleaved muscovite mica and octadecyltrichlorosilane (OTS) dissolved in toluene (c = 1.0 mmol/L) have been used as substrate and precursor, respectively. The water content of the adsorption solution was between 14.6 and 16.6 mmol/L. Adsorption experiments were carried out in a temperature range between 5 and 45 degrees C, and the obtained submonolayer ODS films were characterized with atomic force microscopy (AFM). Besides the morphology of the films, also information on the surface coverage has been obtained by quantitative evaluation of the AFM images. Depending on the temperature, evidence for both ordered and disordered expanded ODS phases has been found. The pronounced maximum in surface coverage--in contrast to adsorption on silicon substrates--at a temperature of about 27 degrees C and the different morphology of the submonolayer films as compared to silicon substrates could be explained in terms of a deposition, diffusion, and aggregation (DDA) model.     

Controlling the properties of self-assembled monolayers by substrate curvature

Properties of self-assembled monolayers (SAMs) can be tailored by the curvature of the underlying surface. This is so because on a curved support the density of SAM headgroups is always smaller than that of the surface-attachment sites. This density difference increases with increasing curvature and is most pronounced for SAMs formed on nanoscopic particles. This Perspective describes systems in which nanoscale curvature causes pronounced changes in the pK(a) of acid-presenting SAMs or in the electrochemical potential of redox-active molecules (including supramolecular "switches") attached to nanoparticles. It is suggested that in nanoparticles having regions of different curvature these geometrical differences can translate into site-selective charging; such "patchy" particles could be used as building blocks of pH-sensitive assemblies.     

Nanotribological properties of alkanephosphonic acid self-assembled monolayers on aluminum oxide: effects of fluorination and substrate crystallinity

Two phosphonic acid (PA) self-assembled monolayers (SAMs) are studied on three aluminum oxide surfaces: the C and R crystallographic planes of single crystal alpha-alumina (sapphire) and an amorphous vapor-deposited alumina thin film. SAMs are either fully hydrogenated CH3(CH2)17PO3H2 or semifluorinated CF3(CF2)7(CH2)11PO3H2. Atomic force microscope (AFM) topographic imaging reveals that the deposited films are homogeneous, atomically smooth, and stable for months in the laboratory environment. Static and advancing contact angle measurements agree with previous work on identical or similar films, but receding measurements suggest reduced coverage here. To enable reproducible nanotribology measurements with the AFM, a scanning protocol is developed that leads to a stable configuration of the silicon tip. Adhesion for the semifluorinated films is either comparable to or lower than that for the hydrogenated films, with a dependence on contact history observed. Friction between each film and the tips depends strongly upon the type of molecule, with the fluorinated species exhibiting substantially higher friction. Subtle but reproducible differences in friction are observed for a given SAM depending on the substrate, revealing differences in packing density for the SAMs on the different substrates. Friction is seen to increase linearly with load, a consequence of the tip's penetration into the monolayer.     

Redox mediation at 11-mercaptoundecanoic acid self-assembled monolayers on gold

Cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and digital simulation techniques were used to investigate quantitatively the mechanism of electron transfer (ET) through densely packed and well-ordered self-assembled monolayers (SAMs) of 11-mercaptoundecanoic acid on gold, either pristine or modified by physically adsorbed glucose oxidase (GOx). In the presence of ferrocenylmethanol (FcMeOH) as a redox mediator, ET kinetics involving either solution-phase hydrophilic redox probes such as [Fe(CN)6]3-/4- or surface-immobilized GOx is greatly accelerated: [Fe(CN)6]3-/4- undergoes diffusion-controlled ET, while the enzymatic electrochemical conversion of glucose to gluconolactone is efficiently sustained by FcMeOH. Analysis of the results, also including the digital simulation of CV and EIS data, showed the prevalence of an ET mechanism according to the so-called membrane model that comprises the permeation of the redox mediator within the SAM and the intermolecular ET to the redox probe located outside the monolayer. The analysis of the catalytic current generated at the GOx/SAM electrode in the presence of glucose and FcMeOH allowed the high surface protein coverage suggested by X-ray photoelectron spectroscopy (XPS) measurements to be confirmed.     

Mediated oxidation of ascorbic acid on a homologous series of ferrocene-terminated self-assembled monolayers

The kinetics of electrocatalytic oxidation of ascorbate was studied on a series of redox self-assembled monolayers (SAMs) of the general formula Fc(CH2)4COO(CH2)nSH as electron-transfer mediators, where Fc is the ferrocenyl group and n = 3, 6, 9, and 11. We show that the rate of electron transfer from ascorbate to the surface-confined Fc+ decreases with increasing n. The rationale for the dependence of the rate of electrocatalytic activity and n, in the presence of ClO4, is obtained from Fourier-transform surface-enhanced Raman spectroscopy (FT-SERS), cyclic voltammetry, and electrochemical quartz crystal microbalance (EQCM) data. In particular, FT-SERS shows decreasing amounts of surface-bound ClO4- upon oxidation of the ferrocene with decreasing n, while EQCM data show the effective electrode mass increase was consistently higher on the shorter chain SAMs. This mass increase is likely due to increasing ferricinium cation hydration. As n decreases, the SAMs become less ordered (FT-SERS data), as is widely known from previous literature. Disorder favors water penetration into the SAM, which, in turn, increases the hydration of the Fc+ (EQCM data). Increased hydration of the Fc+ impedes the formation of Fc+-ClO4- ion pairs (EQCM and FT-SERS data), which, consequently, accelerates the electrocatalytic electron transfer from the solution-dissolved ascorbate.     

Maleimido-terminated self-assembled monolayers

Four approaches have been explored for the preparation of maleimido-functionalized self-assembled monolayers (SAMs) on silicon. SAMs prepared by self-assembly of maleimido-functionalized alkyltrichlorosilanes (11-maleimido-undecyl-trichlorosilane) on oxide-covered silicon yield higher signals from maleimido functionalities in ATR-IR (attenuated total reflection IR) spectroscopy and XPS (X-ray photoelectron spectroscopy) than the other three methods. The surface composition of maleimido groups was tailored further by the formation of mixed monolayers with nonfunctionalized alkyltrichlorosilanes (decyltrichlorosilane). The order of the alkyl chains within the monolayers only slightly depends on the composition of the mixed monolayers. We utilized the maleimido-terminated SAMs to bind various nucleophilic compounds, alkylamines, alkylthiols, and thiol-tagged DNA oligonucleotides by means of conjugate addition.     

Chain-length dependence of the conformational order in self-assembled dialkylammonium monolayers on mica studied with soft X-ray absorption

Self-assembled alkyl chain based monolayers on mica are important for industrial and technological processes since they can be employed for an organic modification of the inorganic substrate. The conformational structure and orientational order of the films determine the interaction of the modified substrate with the environment and the chemical character and stability of its surface. We have studied the conformational order in ion exchanged dialkylammonium monolayers adsorbed on mica depending on the length of the alkyl chains systematically with near-edge X-ray absorption fine structure spectroscopy (NEXAFS). In addition, films were characterized by water contact angle measurements. The experimentally determined average tilt angles of the chains are discussed in terms of the degree of order. It was found that the absolute number of gauche defects in the films increases with decreasing chain length.     

Conglomerate crystallization on self-assembled monolayers

In this communication, we demonstrate that chiral self-assembled monolayers can be used for polymorphism control of chiral crystals. We studied the crystallization of DL-glutamic acid on chiral self-assembled monolayers and showed that crystallization of DL-glutamic acid on the chiral SAMs resulted in stabilization of the metastable conglomerate form.     

Adsorption and desorption of stearic acid self-assembled monolayers on aluminum oxide

Development of coatings to minimize unwanted surface adsorption is extremely important for their use in applications, such as sensors and medical implants. Self-assembled monolayers (SAMs) are an excellent choice for coatings that minimize nonspecific adsorption because they can be uniform and have a very high surface coverage. Another equally important characteristic of such coatings is their stability. In the present study, both the bonding mechanism and the stability of stearic acid SAMs on two aluminum oxides (single-crystal C-plane aluminum oxide (sapphire) and amorphous aluminum oxide (alumina)) are investigated. The adsorption mechanism is investigated by ex situ X-ray photoelectron spectroscopy and infrared (IR) spectroscopy. The results revealed that stearic acid binds to sapphire surfaces via a bidentate interaction of carboxylate with two oxygen atoms while it binds to alumina surfaces via both bidentate and monodentate interactions. Desorption kinetics of stearic acid self-organized on both aluminum oxide surfaces into water is explored by ex situ tapping mode atomic force microscopy, IR spectroscopy, and contact angle measurements. The results exhibit that the SAMs of stearic acid formed on sapphire are not stable in water and are continuously lost through desorption. Water contact angle measurements of SAMs that are immersed in water further indicate that the desorption rate of adsorbates from atomically smooth terrace sites is substantially faster than that of adsorbates from the sites of surface defects due to weaker molecular interaction with the smooth surface. A time-dependent desorption profile of SAMs grown on amorphous alumina reveals that contact angles decrease monotonically without any regional distinction, providing further evidence for the presence of adsorption sites with different types of affinity on the amorphous alumina surface.     

Supported lipid bilayers lifted from the substrate by layer-by-layer polyion cushions on self-assembled monolayers

The formation of lipid bilayers, lifted from the solid substrate by layer-by-layer polyion cushions, on self-assembled monolayers (SAMs) on gold was investigated by surface plasmon resonance (SPR) and fluorescence recovery after photobleaching (FRAP). The polyions poly(diallyldimethylammonium chloride) (PDDA) and polystyrene sulfonate (PSS) sodium salt were used for the layer-by-layer polyion macromolecular assembly. The cushion was formed by electrostatic interaction of PDDA/PSS/PDDA layers with a negatively charged surface of an SAM of 11-mercaptoundecanoic acid (MUA) on gold. The lipid bilayer membranes were deposited by vesicle fusion with different compositions of SOPS (an anionic lipid, 1-stearoyl-2-oleoyl-phosphatidylserine) and POPC (a zwitterionic lipid, 1-palmitoyl-2-oleoylphosphatidylcholine). In the case of pure SOPS and for lipid mixtures with a POPC composition up to 25%, single bilayers were deposited. FRAP experiments showed that single bilayers supported on PDDA/PSS/PDDA/MUA were mobile at room temperature, with lateral coefficients of approximately (1.2–2.1)×10⁻⁹ cm²/s. The kinetics of the addition of the ion-channel-forming peptide protegrin-1 to the supported bilayers was detected by SPR. A two-step interaction was observed, similar to the association behavior of protegrin-1 with bilayers supported on PDDA/MUA. The results are similar to that of supported lipid bilayers without a layer-by-layer cushion. The model membrane system in this work is a potential biosensor for mimicking the natural activities of biomolecules and is a possible tool to investigate the fundamental properties of biomembranes.     

Direct electrochemistry of cytochrome c on a phosphonic acid terminated self-assembled monolayers

The direct electrochemistry of cytochrome c (cyt c) on a gold electrode modified with 3-mercaptopropylphosphonic acid [HS-(CH₂)₃-PO₃H₂, MPPA] self-assembled monolayers (SAMs) was for the first time investigated. Electrochemical measurements and surface-enhanced infrared absorption spectroscopic reveal that the adsorption kinetics of cyt c on the MPPA-SAMs is very fast (saturation adsorption is completed within 5 s) and the immobilized cyt c molecules retain their native secondary protein structure. The nature of interaction between cyt c and -PO₃H₂ groups is mainly the electrostatic interaction. The direct electrochemistry of the immobilized cyt c on the -PO₃H₂ terminated SAMs with short chain is nearly reversible. Its formal potential (E⁰′ = 18 ± 3 mV vs. SCE) is very close to that of cyt c in an aqueous solution (E⁰′ = 18-22 mV vs. SCE). In addition, the electron transfer rate of cyt c immobilized on -PO₃H₂ terminated SAMs is relatively slow as compared to -SO₃H and -COOH terminated SAMs, indicating excess negative charge density on the SAMs surface will decrease the electron transfer rate of cyt c.     

New dialkyldithiophosphinic acid self-assembled monolayers (SAMs): influence of gold substrate morphology on adsorbate binding and SAM structure

We report the fabrication and characterization of new self-assembled monolayers (SAMs) formed from dihexadecyldithiophosphinic acid [(C(16))(2)DTPA] molecules on gold substrates. In these SAMs, the ability of the (C(16))(2)DTPA headgroup to chelate to the gold surface depends on the morphology of the gold substrate. Gold substrates fabricated by electron-beam evaporation (As-Dep gold) consist of ～50-nm grains separated by deep grain boundaries (～10 nm). These grain boundaries inhibit the chelation of (C(16))(2)DTPA adsorbates to the surface, producing SAMs in which there is a mixture of monodentate and bidentate adsorbates. In contrast, gold substrates produced by template stripping (TS gold) consist of larger grains (～200-500 nm) with shallower grain boundaries (<2 nm). On these substrates, the low density of shallow grain boundaries allows (C(16))(2)DTPA molecules to chelate to the surface, producing SAMs in which all molecules are bidentate. The content of bidentate adsorbates in (C(16))(2)DTPA SAMs formed on As-Dep and TS gold substrates strongly affects the SAM properties: Alkyl chain organization, wettability, frictional response, barrier properties, thickness, and thermal stability all depend on whether a SAM has been formed on As-Dep or TS gold. This study demonstrates that substrate morphology has an important influence on the structure of SAMs formed from these chelating adsorbates.     

Fabrication of self-assembled monolayers (SAMs) and inorganic micropattern on flexible polymer substrate

By grafting (aminopropyl)triethoxysilane (APTES) as the buffer layer on poly(ethylene terephthalate) (PET) surface, the SAMs ofoctadecyltrichlorosilane (OTS), phenyltrichlorosilane (PTCS), vinyltrichlorosilane (VTCS), andp-tolyltrichlorosilane (TTCS) were fabricated on the flexible polymer substrate. The properties of SAMs were accurately controlled by adjusting the immersing time of substrates in the solutions and the concentration of the solutions. The SAMs acted as templates, and TiO2 micropattern was successfully deposited on OTS, TTCS, and PTCS SAMs.     

Preparation and nanoscale mechanical properties of self-assembled carboxylic acid functionalized pentathiophene on mica

The oligothiophene derivative 4-(5' " '-decyl-[2,2';5',2' ';5' ',2' ";5' ",2' " '] pentathiophen-5-yl)-butyric acid (D5TBA) was synthesized by Stille cross-coupling methods using functionalized thiophene monomers. The structural and mechanical properties of D5TBA self-assembled monolayers on mica have been studied by atomic force microscopy (AFM). The self-assembled films were prepared by immersing the mica in dilute chloroform or tetrahydrofuran (THF) solutions. The films were predominantly of monolayer thickness with molecules packed in nearly upright orientations. In regions covered with multilayers, the molecules in each monolayer were oriented opposite to those in the neighboring ones, that is, with COOH-COOH and CH3-CH3 contact. The nature of the end group in contact with the substrate depended on the solvent used and the degree of hydration of the substrate, with hydrophobic chloroform solvent favoring the methyl end down and hydrophilic THF favoring the acid group end down. The orientation could also be controlled by dipping using the Langmuir-Blodgett technique.