Transport of organic solutes through amorphous teflon AF films

Fluorous media have great potential for selective extraction (e.g., as applied to organic synthesis). Fluorous polymer films would have significant advantages in fluorous separations. Stable films of Teflon AF 2400 were cast from solution. Films appear defect-free (SEM; AFM). Rigid aromatic solutes are transported (from chloroform solution to chloroform receiving phase) in a size-dependent manner (log permeability is proportional to -0.0067 times critical volume). Benzene's permeability is about 2 orders of magnitude higher than in comparable gas-phase experiments. The films show selectivity for fluorinated solutes in comparison to the hydrogen-containing control. Transport rates are dependent on the solvent making up the source and receiving phases. The effect of solvent is, interestingly, not due to changes in partition ratio, but rather it is due to changes in the solute diffusion coefficient in the film. Solvents plasticize the films. A less volatile compound, -COOH-terminated poly(hexafluoropropylene oxide) (4), plasticizes the films (T(g) = -40 degrees C). Permeabilities are decreased in comparison to 4-free films apparently because of decreased diffusivity of solutes. The slope of dependence of log permeability on critical volume is not changed, however.     

Sorption and diffusion of organic vapors in amorphous Teflon AF2400

Vapor sorption in amorphous Teflon AF2400 of various organic solutes was studied in a wide range of activity at 25 °C by means of the gravimetric technique. The sorption isotherms of hexane, toluene, and chloroform were shown to be concave to the pressure axis and are consistent with the dual mode sorption model (DMS). The parameters of the DMS model k_D and b reveal a linear correlation with squared critical temperature of solutes T. The third model parameter, the Langmuir sorption capacity C′_H decreases when the size of solutes (critical volume) increases. Sorption isotherms of methanol and ethanol were shown to be convex to the pressure axis and are consistent with cluster formation in this strongly hydrophobic polymer. Concentration‐dependent diffusion coefficients D were determined using a linear implicit difference scheme in analysis of sorption kinetics. It was shown that D values increase exponentially with concentration for all the solutes, except alcohols for which exponential reduction of D(C) was observed. The partitioning of the thermodynamic and mobility contributions in D indicated that the reduction of D values of alcohols is consistent with clustering phenomena in AF2400. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 832–844, 2006     

Crystal and amorphous orientation behavior of poly(chlorotrifluoroethylene) films in relation to crystalline superstructure

The relationship between the crystalline superstructure of polymer films and molecular orientation was studied in cold-drawn poly(chlorotrifluoroethylene) films by wide-angle x-ray diffraction, birefringence, and depolarized light scattering. By changing crystallization conditions, specimens with almost identical crystallinity but different crystalline superstructures were obtained; i.e., (1) a structure having a random array of crystallites, (2) a superstructure having a rod-like orientation correlation of the chains (a prespherulitic and sheaf-like superstructure), and (3) spherulitic superstructure. Upon stretching of specimens, crystallites initially randomly arranged orient with their chain axes along the stretching direction in accord with simple affine deformation. The amorphous chains also orient along the stretching direction. The orientation behavior of the specimens having the rod-like superstructure is similar to that of the specimens with a random array of crystallites, indicating that the interaction between the crystallites in the superstructure is relatively weak. The molecular orientation behavior of the spherulitic specimens, however, strongly deviates from simple affine deformation owing to strong interaction of the crystallites in the spherulites. The deviation can be interpreted in terms of spherulite deformation and of internal reorientation of chains within deformed spherulites.     

Properties of thin Teflon AF 2400 coatings deposited onto carbon fabric from solutions in supercritical carbon dioxide

For the design of hydrophobized conductive gas diffusion layers of the electrodes of polymercontaining fuel cells, of great interest is the method for the formation of a fluoropolymer film from fluoropolymer solution in supercritical carbon dioxide. The present work describes the systematic studies on the carbon-fabric-deposited Teflon AF 2400 coatings obtained by this method. The electrical and geometric characteristics of the coatings, their elemental compositions, and stabilities are studied. It is shown that supercritical carbon dioxide allows the deposited fluoropolymer to penetrate homogeneously into the depth of carbon fabric to form a uniform coating around single individual fibers. The optimum limits of variation in the Teflon AF 2400 amount upon production of the gas diffusion layers of polymer electrolyte, alkaline, and phosphoric acid fuel cells are determined.     

The boiling point and molar enthalpy of vaporization of fluorint FC-70 N(C5F11)3

N(C₅F₁₁)₃ (Fluorint FC-70) has been chosen as the test material to compare the chemicophysical data obtained by static-sample and DSC methods. The normal boiling point, the molar enthalpy of vaporization, and the constants of the Antoine equation of fluorint FC-70 are reported. DSC can be developed into a simple and rapid routine instrument to determine the enthalpy of vaporization as well as the boiling point of liquid, particularly at relative high temperature.     

Electrochemical behavior of poly(ferrocenyldimethylsilane-b-dimethylsiloxane) films

The electrochemical behavior of poly(ferrocenyldimethylsilane-b-dimethylsiloxane) (PFDMS-b-PDMS) films deposited on a glassy carbon electrode was investigated by means of cyclic voltammetry (CV). The influences of the solvent, film thickness, temperature, and PDMS block length in PFDMS-b-PDMS on the electrode process were discussed. It was found that in 0.1 M aqueous LiClO(4) the electrochemical processes of the films on a glassy carbon electrode were complex and have a low rate of electron transport and mass diffusion. The kinetic parameters obtained indicated that the electrode process was controlled by both the electrode reaction and mass diffusion.     

Rigid amorphous fraction and melting behavior of poly(ethylene terephthalate)

The multiple melting behavior of poly(ethylene terephthalate) (PET) is generally attributed to the fusion of original crystals recrystallized during the heating at conventional scanning rate. In the present study, the triple and double melting behavior that is observed after isothermal crystallization at T _c lower and higher than 215 °C, respectively, is put in relation with the presence and absence of rigid amorphous fraction around the original primary crystal lamellae. The complex melting behavior is explained by assuming that two different morphologies of primary crystals develop during crystallization at temperatures lower than 215 °C, in a proportion that is a function of the crystallization temperature: chain cluster aggregations with a high percentage of rigid amorphous fraction on the boundaries and small crystals with a high percentage of adjacent reentry folding and reduced constraints at the amorphous/crystal interphase. These distinct morphologies differently transform upon heating at low scanning rate, originating two endotherms. On the contrary, after crystallization at T _c ?>?215 °C, all the primary crystalline structure, which probably are characterized by the same morphology made of tightly chain folded lamellae and absence of rigid amorphous fraction, undergo the same reorganization route, originating a single endotherm.     

Photochemical behavior of poly(ethylacryloylacetate) and poly(acryloylacetone) films

Films of poly(ethylacryloylacetate) (PEAA) and poly(acryloylacetone) (PAA) were subjected to UV irradiation (λ = 254 nm) at room temperature. The photoinduced structure transfer from cis-enol onto a diketo forms has been investigated. The structure transfer caused by UV light was found to be slower than for the corresponding process in solution. The spectral investigations (UV, IR) showed reversible process of photoketonization. The results were analyzed in terms of the model for the participation of the trans-enol form in the process of the ketonization. Based on the results obtained, some general conclusions were made about the organization of the units in the polymer chain. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3683–3688, 1997     

Low-frequency glow discharge treatment of amorphous poly(ethylene terephthalate) films

The influence of treatment in a low-frequency glow discharge on the surface properties of an amorphous poly(ethylene terephthalate) (PET) film was studied. It was shown that, at identical external discharge parameters, changes in the wettability of plasma-treated PET films depended on its morphological structure—the amorphous film had higher values of the contact angle and lower values of the surface charge density than a biaxially oriented poly(ethylene terephthalate) of the PET-E brand.     

Chain structure and stiffness of Teflon AF glassy amorphous fluoropolymers

The structure of the amorphous perfluorinated polymer Teflon AF 2400 and other structurally close perfluoropolymers was studied by means of a quantum chemistry method. The electronic and structural characteristics of the repeating unit and polymer models with ten and nine monomer units were obtained. It was found that two nonplanar isomers can exist for different models of the perfluorinated dioxole ring with a difference of their energy minimums of 10.8 kJ/mol. The orthogonal-block structure of the polymer chain of the perfluorodioxole homopolymer and its copolymer with tetrafluoroethylene was proposed, the block size was found, and a possible diameter of the void formed by two neighboring polymer chains was evaluated. Potential energy curves for the rotation of certain chain fragments about different bonds of the polymer main chain were constructed, and the polymer stiffness was shown to substantially depend on the molar ratio between perfluorodioxole and tetrafluoroethylene units in the copolymer and on the geometry of the perfluorodioxole ring.     

Layer-by-layer growth of thin amorphous solid water films on Pt(111) and Pd(111)

The growth of amorphous solid water (ASW) films on Pt(111) is investigated using rare gas (e.g., Kr) physisorption. Temperature programmed desorption of Kr is sensitive to the structure of thin water films and can be used to assess the growth modes of these films. At all temperatures that are experimentally accessible (20-155 K), the first layer of water wets Pt(111). Over a wide temperature range (20-120 K), ASW films wet the substrate and grow approximately layer by layer for at least the first three layers. In contrast to the ASW films, crystalline ice films do not wet the water monolayer on Pt(111). Virtually identical results were obtained for ASW films on epitaxial Pd(111) films grown on Pt(111). The desorption rates of thin ASW and crystalline ice films suggest that the relative free energies of the films are responsible for the different growth modes. However, at low temperatures, surface relaxation or "transient mobility" is primarily responsible for the relative smoothness of the films. A simple model of the surface relaxation semiquantitatively accounts for the observations.     

Electron-stimulated sputtering of thin amorphous solid water films on Pt(111)

The electron-stimulated sputtering of thin amorphous solid water films deposited on Pt(111) is investigated. The sputtering appears to be dominated by two processes: (1) electron-stimulated desorption of water molecules and (2) electron-stimulated reactions leading to the production of molecular hydrogen and molecular oxygen. The electron-stimulated desorption of water increases monotonically with increasing film thickness. In contrast, the total sputtering--which includes all electron-stimulated reaction channels--is maximized for films of intermediate thickness. The sputtering yield versus thickness indicates that erosion of the film occurs due to reactions at both the water/vacuum interface and the Pt/water interface. Experiments with layered films of D2O and H2O demonstrate significant loss of hydrogen due to reactions at the Pt/water interface. The electron-stimulated sputtering is independent of temperature below approximately 80 K and increases rapidly at higher temperatures.     

Fracture behavior of amorphous and semicrystalline blends of poly(vinylidene fluoride) and poly(methyl methacrylate)

The fracture behavior of blends of poly(vinylidene fluoride) and poly(methyl methacrylate) was investigated all over the composition range. A detailed analysis of the net stress versus crack opening displacement curves was performed. Fracture surface observations allowed statements on the process zone characteristics ahead of the crack tip. For the amorphous blends, the crack initiation energy is well related to the glass transition temperature. For the semicrystalline blends, the fracture energy is correlated with the degree of crystallinity. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Birefringence of amorphous polyoxides: Stress-optical behavior of poly(3-methyltetrahydrofuran)

The stress-optical behavior of an unswollen elastomeric network of poly(3-methyltetrahydrofuran) was measured for elongation ratios a in the range 1.182–1.549, at several temperatures between 20 and 60°C. No evidence of strain-induced crystallization was found; moreover, the dependence of birefringence Δn on true stress f/A was linear in the interval of α investigated. Values of Δa ranged from 2.4 to 2.8 in units of 10^?24 cm³, in the temperature range studied, with a temperature coefficient 3.1 × 10^?3 K^?1. Theoretical calculations carried out with the rotational-isomeric-state model gave values of Δa noticeably smaller than the experimental results; however, a small increase in the backbone valence angles θ improved the theoretical result of Δa without worsening that of the dipole ratio. Analysis of the Δa results seems to corroborate the conclusion obtained through the study of dipole moments concerning the preference for nucleophilic attack on the less hindered α carbon in the monomer. Theoretical and experimental values of the temperature coefficient of Δa were in clear disagreement; a qualitative explanation for this discrepancy is discussed.     

A Relative Study on Two-photon Absorption Properties of C60 and C70

We have theoretically investigated the one- and two-photon absorption properties of C60 and C70 using the ZINDO method. From the results it is suggested that the one-photon absorption spectra are in agreement with the experimental observations. It is found that the maximum TPA cross section of C70 is more than twice that of C60,which is consistent with the experimental results. A notable point is that the TPA process of C60 is different from that of C70 as well as other ordinary conjugated molecules.     

Sm~(3+)掺杂(Y,Tb)AG:Ce~(3+)荧光粉的制备及光谱性能

采用柠檬酸溶胶凝胶燃烧合成法制备了一系列组成的(Y,Tb)3Al5O12:Ce3+,Sm3+荧光粉。通过X射线衍射、荧光光谱研究了不同Sm3+离子共掺杂浓度下(Y,Tb)AG:Ce3+荧光粉的晶体结构及光致发光性能。Rietveld全图拟合(Rietveld method of wholepattern fitting)结果表明:掺杂后样品仍为纯立方石榴石相,随着Sm3+离子共掺杂浓度的增加,样品的晶胞参数增大。在467 nm激发下,激发能由Ce3+离子向Sm3+离子单向传递,从而在617nm处出现红光发射。Tb3+离子取代不利于Ce3+离子与Sm3+离子的能量传递,同时Ce3+离子受更强的晶体场作用及与O2-离子间增强的共价性使发射主峰红移,Sm3+掺杂的TAG:Ce体系中,激发能由敏化剂Ce3+离子向激活剂Sm3+离子的传递路径包括5d→4f2F5/2,7/2(Ce3+)和7F6→5D4(Tb3+)到4G5/2→6H7/2(Sm3+)两部分。     

Matrix-dependent instability of selenium(IV) stored in teflon containers

Solutions of selenium(IV) standards with different acid matrices were stored in containers constructed of boosilicate glass, conventional polyethylene, and fluorinated ethylenepropylene (teflon FEP). After 50 days of storage in FEP, there were highly significant losses of Se(IV) from standards in either 5% HCl/5% H₂SO₄, or 5% H₂SO₄. Increasing the hydrochloric acid concentration, e.g., 15% HCl/5% H₂SO₄, greatly reduced this loss. Addition of selenium-75 (selenate-free) indicated that the losses did not result from physical adsorption onto container surfaces. It is shown that the losses were caused by oxidation of Se(IV) to Se(VI).     

Degradation behavior of poly (l-lactide-co-glycolide) films through gamma-ray irradiation

Gamma-ray irradiation is a very useful tool to improve the physicochemical properties of various biodegradable polymers without the use of a heating and crosslinking agent. The purpose of this study was to investigate the degradation behavior of poly (l-lactide-co-glycolide) (PLGA) depending on the applied gamma-ray irradiation doses. PLGA films prepared through a solvent casting method were irradiated with gamma radiation at various irradiation doses. The irradiation was performed using 60Co gamma-ray doses of 25–500 kGy at a dose rate of 10 kGy/h.The degradation of irradiated films was observed through the main chain scission. Exposure to gamma radiation dropped the average molecular weight (M_n and M_w), and weakened the mechanical strength. Thermograms of irradiated film show various changes of thermal properties in accordance with gamma-ray irradiation doses. Gamma-ray irradiation changes the morphology of the surface, and improves the wettability. In conclusion, gamma-ray irradiation will be a useful tool to control the rate of hydrolytic degradation of these PLGA films.