Thermally induced color change in electrospun fiber mats

Electrospinning is a process that employs a high static electrical potential to produce polymeric fibers of nanoscale diameter. The process has been utilized to achieve color change by electrospinning black polymer solutions to produce white fiber mats. When subsequently heated, the electrospun mats undergo a color change from white to black. This phenomenon is demonstrated with three polymer/solvent systems. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 752–757, 2004     

Calix[4]arene-based fluorescent probe and the adsorption capacity of its electrospun nanofibrous film for the cesium cation as an adsorbent

Calix[4]arene-based cation receptor 1 has been synthesised by following a multi-step synthetic procedure. The fluorescence properties of 1 upon the addition of various metal ions were investigated by fluorescence spectroscopy. As a result, it was revealed that 1 displayed dramatic quenching effect upon the exposure to Cs⁺. In contrast, no significant quenching effects were observed upon the addition of other metal ions such as Li⁺, Na⁺, K⁺, Mg²⁺, Ca²⁺, Sr²⁺, Ag⁺, Zn²⁺ and Ni²⁺. Compound 1 was also found by Job plot to form a 1:1 complex with Cs⁺. In addition, we also prepared 1-embedded electrospun nanofibrous film (NF-1) as an adsorbent for Cs⁺. NF-1 is proved to adsorb Cs⁺ effectively from an aqueous solution, indicating that it would be usefully utilised as an adsorbent to remove Cs⁺.     

Preparation and characterization of pentaerythritol/butane tetracarboxylic acid/polyethylene glycol crosslinking copolymers as solid-solid phase change materials

Pentaerythritol/butane tetracarboxylic acid/polyethylene glycol (PBPEG) crosslinking copolymers as a novel solid-solid phase change material (SSPCM) were successfully synthesized through the reaction mechanism and conditions of hydroxyl-carboxyl condensation reaction. The composition and chemical structure, crystalline properties, phase change behaviors, thermal reliability and chemical stability of PBPEG crosslinking copolymers were investigated by Fourier transform infrared spectroscopy (FT-IR), wide-angle X-ray diffraction (WAXD), polarization optical microscopy (POM), differential scanning calorimetry (DSC), and thermogravimetry (TGA), respectively. The results show that PBPEG crosslinking copolymers have typical solid-solid phase transition temperatures in the range of 10.31～53.27°C and high latent heat enthalpy in the range of 89.6～102.8 J/g, the synthesized SSPCMs have good thermal reliability and chemical stability after 300 thermal cycles, and PBPEG crosslinking copolymers have good thermal stability before 364°C. In summary, the synthesized PBPEG crosslinking copolymers could be potentially used for thermal energy storage.     

Hyperbranched polyurethane as novel solid-solid phase change material for thermal energy storage

A series of novel hyperbranched polyurethane copolymer (HB-PUPCM) using hyperbranched polyester as chain extender was prepared via a two-step process. The phase transition behaviors and morphology of the HB-PUPCM films were investigated using differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMA), thermo-gravimetric analysis (TGA), wide-angle X-ray diffraction (WAXD), polarizing optical microscopy (POM) and tapping-mode atomic force microscopy (AFM). HB-PUPCM was proven to a good polymeric solid-solid phase change heat storage material.     

相变蓄热材料研究进展

相变蓄热材料(恒温潜热热能储存材料)是目前最热门的功能材料之一。它在发生相变时储存、放出的热量能够帮助所在系统进行能量的储存,同时可以一定程度上缓解双方在时间、强度及地点上的不匹配程度。相变蓄热材料优点突出,其中包括在使用过程中自身温度变化较小、有很好的稳定性、储热能力较强等。此类材料对环境友好,响应了国家近年来节能环保的政策,同时也可以极大地优化所在系统的运行效率。本文综述了近年来几类相变蓄热材料的种类、特点及国内外学者应对于不同缺陷做出的改进及其应用于行业的研究现状,并对未来的发展进行了探讨与展望。     

Crystallisation, melting, recrystallisation and polymorphism of n-eicosane for application as a phase change material

Phase change materials (PCM) provide thermoregulation originating from the latent heat exchanged during melting or crystallisation. Linear hydrocarbons have weak interactions, but high symmetry, providing an effective quantity of latent heat over the most acceptable temperature range for applications. The ability to both melt and crystallise over a narrow range is made complex by nucleation, polymorphism and the kinetic nature of these changes. Differential scanning calorimetry (DSC), optical microscopy and temperature modulated DSC (TMDSC) was used to study the melting of n-eicosane. This PCM has a low degree of supercooling and conversion to the most stable crystalline state (triclinic) that occurs rapidly from a metastable phase (rotator) state on cooling. TMDSC revealed a small, yet similar degree of thermodynamic reversibility in the melting of each of the crystalline phases.     

水性聚氨酯相变储能材料的相变机理

以聚乙二醇(PEG)为软段、六亚甲基二异氰酸酯-1,4-丁二醇-二羟甲基丙酸(HDI-BDO-DMPA)为硬段,制备了一系列水性聚氨酯相变储能材料(WPUPCM)。在相变过程中,由于软段PEG由聚合前的固-液相变转化为聚合后的固-固相变,因此,所制备的WPUPCM表现出固-固相变特性。为了研究其固态相变行为的本质和形成机理,揭示该类聚合物的能量贮存和转换机理,应用偏光显微镜、扫描电镜、原子力显微镜、X射线衍射仪分析研究了PEG、WPUPCM在相变过程中的晶体结构变化特征,讨论了WPUPCM固-固相转变的机理。     

Synthesis and thermal properties of poly(styrene-co-acrylonitrile)-graft-polyethylene glycol copolymers as novel solid–solid phase change materials for thermal energy storage

A novel poly(styrene-co-acrylonitrile)-graft-polyethylene glycol(SAN-g-PEG) copolymer was synthesized as new solid–solid phase change materials(SSPCMs) by grafting PEG to the main chain of poly(styrene-co-acrylonitrile). The chemical structure of the SAN-g-PEG was confirmed by the Fourier transform infrared(FT-IR) and proton nuclear magnetic resonance(1H NMR) spectroscopy techniques. The thermal energy storage properties and the storage durability of the SAN-g-PEG were investigated by differential scanning calorimetry(DSC). The SAN-g-PEG was endowed with the solid–solid phase transition temperatures within the range of 23–36 8C and the latent heat enthalpy ranged from 66.8 k J/kg to 68.3 k J/kg. Thermal cycling tests revealed that the SAN-g-PEG kept great heat storage durability after 1000 thermal cycles. The thermal stability was evaluated by a thermal gravity analysis(TGA), and the initial decomposition temperature(Td) of SAN-g-PEG is 350 8C, which proves that the SAN-g-PEG possessed good thermal stability.     

Polypropylene as a potential matrix for the creation of shape stabilized phase change materials

Phase change materials, based on isotactic polypropylene (PP) blended with soft and hard Fischer−Tropsch paraffin wax respectively, were studied in this paper. DSC, DMA, TGA and SEM were used to determine the structure and properties of the blends. While paraffin waxes in the blend changed state from solid to liquid, the PP matrix kept the material in a compact shape. Strong phase separation was observed in both cases, which was more pronounced in the case of soft paraffin wax. Despite the fact that both grades of paraffin wax are not miscible with PP due to different crystalline structures, it was shown that the hard Fischer−Tropsch paraffin wax is more compatible with PP than the soft one. Both waxes plasticized the PP matrix. TGA showed that PP blended with the hard Fischer−Tropsch wax degrades in just one step, whereas blends containing soft paraffin wax degrade in two distinguishable steps. SEM exposed a completely different morphology for the two paraffin waxes and confirmed the lower compatibility of PP and soft paraffin wax. The soft and hard characters of the waxes were manifested in the viscoelastic properties, where the blends containing soft paraffin wax exhibited a lower elastic modulus than pure polypropylene, whereas the hard Fisher−Tropsch paraffin wax solidified the matrix. However, both kinds of blends were able to sustain the dynamic forces applied by the DMA within five cycle runs implying good shape stability.     

常低温相变储热材料的研究和应用

将常低温相变储热材料分类,介绍了常低温相变储热材料的种类及各自特点,对固-液相变、固-固相变储热材料的性能、优缺点和应用进行了讨论,讲述了目前人们针对常低温相变储热材料的缺陷采取的解决方法。     

石蜡/P(MMA-co-AA)核壳结构相变蓄能微胶囊的制备

以熔点在58~60℃的半精炼石蜡作为相变芯材,与单体、分散剂水溶液形成核壳结构分散液,室温下自由基聚合制备甲基丙烯酸甲酯-丙烯酸的共聚物(P(MMA-co-AA))为壳材的微胶囊.分别用相差显微镜、扫描电镜、差示扫描量热分析仪和傅里叶变换红外光谱仪测定了微胶囊的形貌、热性能和壳材化学结构.微胶囊的直径范围为1~5μm,其中相变芯材的含量可达70%左右,具有较高的相变潜热(99 J/g),有望应用于空调、供暖等领域.     

Effects of Total Thermal Balance on the Thermal Energy Absorbed or Released by a High-Temperature Phase Change Material

Front tracking and enthalpy methods used to study phase change processes are based on a local thermal energy balance at the liquid–solid interface where mass accommodation methods are also used to account for the density change during the phase transition. Recently, it has been shown that a local thermal balance at the interface does not reproduce the thermodynamic equilibrium in adiabatic systems. Total thermal balance through the entire liquid–solid system can predict the correct thermodynamic equilibrium values of melted (solidified) mass, system size, and interface position. In this work, total thermal balance is applied to systems with isothermal–adiabatic boundary conditions to estimate the sensible and latent heat stored (released) by KNO3 and KNO3/NaNO3 salts which are used as high-temperature phase change materials. Relative percent differences between the solutions obtained with a local thermal balance at the interface and a total thermal balance for the thermal energy absorbed or released by high-temperature phase change materials are obtained. According to the total thermal balance proposed, a correction to the liquid–solid interface dynamics is introduced, which accounts for an extra amount of energy absorbed or released during the phase transition. It is shown that melting or solidification rates are modified by using a total thermal balance through the entire system. Finally, the numerical and semi-analytical methods illustrate that volume changes and the fraction of melted (solidified) solid (liquid) estimated through a local thermal balance at the interface are not invariant in adiabatic systems. The invariance of numerical and semi-analytical solutions in adiabatic systems is significantly improved through the proposed model.     

Reversible swelling as a strategy in the development of smart membranes from electrospun polyvinyl alcohol nanofiber mats

This work presents an electrospun nanofibrous membrane for water treatment, designed to reduce its pores through polymer swelling to retain contaminants, and after that, reopening them for easy cleaning. It consists of a polyvinyl alcohol (PVA) mat crosslinked with a natural agent to avoid water solubility but allow a high swelling of its nanofibers. Then, when the membrane is brought into contact with water, a transitory state occurs during which nanofibers increase their diameter 68%, closing the pores between them. For studying the swelling reversal effect, distilled water filtering was used observing a decrease in the permeate flow over time until a steady state is reached. This phenomenon is explained by the closure of pores, and it is described with a fouling model widely used in the literature. Thanks to this decrease in the pore size, the membrane achieves a rejection rate much higher than conventional PVA electrospun membranes, being capable to retain 20 nm nanoparticles with a rejection rate up to 99%. Swelling is reversible through a simple drying process, which allows reopening the pores and cleaning the fouling easily. Both the membrane and its use strategy extend the capacity of electrospun mats in a sustainable way.     

正十六烷聚脲微胶囊化相变材料

用界面聚合法，合成了直径大约2.5 μm可用于热能储存含相变材料的聚脲包覆微胶囊.在含乳化剂的水溶液中，将溶有芯材正十六烷的有机相乳化成微米级油性液滴，随后加入的水溶性单体二胺与甲苯2,4-二异氰酸酯在胶束界面相互反应形成囊壁.分别用乙烯二胺，1,6-己二胺和它们的混合物作为水溶性单体进行了研究.并用红外光谱和热分析分别考察了不同胺类对微胶囊化学结构和热性质的影响.红外谱图显示合成了聚脲微胶囊，热重曲线表明含正十六烷的聚脲微胶囊能够耐受大约300 ℃高温，差示扫描量热测试表明所有样品均具有合适的相转变热，冷热循环实验揭示微胶囊能够维持储热容量不衰减.研究表明微胶囊化的正十六烷作为相变储热材料具有良好的应用前景.     

ASA/SEBS/paraffin composites as phase change material for potential cooling and heating applications in building

Phase change material (PCM) is able to melt and crystalize with a high heat of phase change at constant temperature, which provides new and green cooling and heating strategies for buildings. In this work, PCMs for buildings composed of acrylonitrile‐styrene‐acrylate copolymer (ASA), polystyrene‐b‐poly(ethylene/butylene)‐b‐polystyrene triblock copolymer (SEBS) and paraffin were fabricated by melt blending. The results of the accelerated leakage test indicated an excellent ability of PCMs to keep paraffin from leakage. Thermal properties suggested that the phase change enthalpy of PCMs increased with the increasing content of paraffin and their phase change temperature was close to the comfortable sensible temperature of human body, which made it quite suitable for building cooling and heating. Besides, PCMs presented excellent stability and reusability after several thermal cycling tests. The temperature test conducted with self‐designed cylindrical devices gave a more sufficient and direct demonstration of the cooling and heating effect. Remarkably, excellent cooling and heating performance (both as high as 15°C) of the composites could be obtained with the addition of paraffin. And the time span of the cooling and heating process was as long as 5 and 7.5 hours, respectively. Owing to its excellent cooling and heating capabilities, the ASA/SEBS/paraffin composites are of great potential to be applied in building temperature control.     

A Review on Polymeric-Based Phase Change Material for Thermo-Regulating Fabric Application

Abstract

Phase Changing Materials (PCM) portrays proficiency to liberate perceptible amount of latent heat on the course of phase transformation between liquid-solid or solid-liquid, thereby creating momentary warmth or cooling effect. PCM has been utilized in garments for introducing thermoregulating effect to diminish thermal discomfort of clothing. Assimilation of thermal energy by PCM causes delay in upsurge of microclimate temperature and results in substantial diminution of moisture release from skin thereby leading to inhibition of heat stress conditions and enhancement of thermo-physiological wearing comfort. Simultaneously, the insulating characteristic of such garment can also avert wearer from certain pivotal corollaries like hypothermia or heat syncope, keeping the individual in consolation owing to their automatic acclimatizing attribute in accordance with body and ecological temperature. As the assimilation of PCM into various textile materials have been extensively studied by researchers, an attempt has been made to explicate the recent existing literatures that have successfully integrated and implemented PCM in textile, concentrating on characteristics of PCMs integrated into fibers, and fabrics for potential industrial applications. Finally, various methodologies like coating, spinning & lamination being utilized for applying PCMs onto textiles for developing thermoregulated clothing have been discussed & concludes with challenges & future prospects.     

Characterization of Unripe and Mature Avocado Seed Oil in Different Proportions as Phase Change Materials and Simulation of Their Cooling Storage

Environmental problems have been associated with energy consumption and waste management. A solution is the development of renewable materials such as organic phase change materials. Characterization of new materials allows knowing their applications and simulations provide an idea of how they can developed. Consequently, this research is focused on the thermal and chemical characterization of five different avocado seed oils depending on the maturity stage of the seed: 100% unripe, 25% mature-75% unripe, 50% mature-50% unripe, 75% mature-25% unripe, and 100% mature. The characterization was performed by differential scanning calorimetry, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The best oil for natural environments corresponded to 100% matured seed with an enthalpy of fusion of 52.93 J·g−1, and a degradation temperature between 241–545 °C. In addition, the FTIR analysis shows that unripe seed oil seems to contain more lipids than a mature one. Furthermore, a simulation with an isothermal box was conducted with the characterized oil with an initial temperature of −14 °C for the isothermal box, −27 °C for the PCM box, and an ambient temperature of 25 °C. The results show that without the PCM the temperature can reach −8 °C and with it is −12 °C after 7 h, proving its application as a cold thermal energy system.     

Preparation and Characterization of Microencapsulated Hexadecane Used for Thermal Energy Storage

Polyurea microcapsules about 2.5μm in diameter containing phase change material for thermal energy storage application were synthesized and characterized by interfacial polycondensation method with toluene-2,4-diisocyanate and ethylenediamine as monomers in an emulsion system. Hexadecane was used as a phase change material and OP, which is nonionic surfactant, and used as an emulsifier. The chemical structure and thermal behavior of the microcapsules were investigated by FTIR and thermal analysis respectively. The results show encapsulated hexadecane has a good potential as a solar energy storage material.     

Natural aging of shape stabilized phase change materials based on paraffin wax

Natural aging of shape-stabilized phase change materials containing linear low density polyethylene (LLDPE), paraffin wax and expanded graphite (EG) in Qatari climate has been studied. It was found that expanded graphite significantly improved the performance of prepared SSPCMs in multiple ways. Firstly, EG suppressed leakage of paraffin wax from the compact shape of SSPCMs. The addition of 15 wt% of EG to shape stabilized phase change materials (SSPCMs) containing 50 wt% of wax caused a decreasing in the leakage of wax by 50% over 210 days of natural aging.Secondly, ∖expanded graphite enhanced the photochemical stability of the blends; this was confirmed by FTIR analysis, where carbonyl index decreased with EG content.