Structural and electrochemical characterization of polyaniline/LiCoO2 nanocomposites prepared via a Pickering emulsion

Polyaniline (PANI)/LiCoO₂ nanocomposite materials are successfully ready through a solid-stabilized emulsion (Pickering emulsion) route. The properties of nanocomposite materials have been put to the test because of their possible relevance to electrodes of lithium batteries. Such nanocomposite materials appear thanks to the polymerization of aniline in Pickering emulsion stabilized with LiCoO₂ particles. PANI has been produced through oxidative polymerization of aniline and ammonium persulfate in HCl solution. The nanocomposite materials of PANI/LiCoO₂ could be formed with low amounts of PANI. The morphology of PANI/LiCoO₂ nanocomposite materials shows nanofibers and round-shape-like morphology. It was found that the morphology of the resulting nanocomposites depended on the amount of LiCoO₂ used in the reaction system. Ammonium persulfate caused the loss of lithium from LiCoO₂ when it was used at high concentration in the polymerization recipe. Highly resolved splitting of 006/102 and 108/110 peaks in the XRD pattern provide evidence to well-ordered layered structure of the PANI/LiCoO₂ nanocomposite materials with high LiCoO₂ content. The ratios of the intensities of 003 and 104 peaks were found to be higher than 1.2 indicating no pronounced mixing of the lithium and cobalt cations. The electrochemical reactivity of PANI/LiCoO₂ nanocomposites as positive electrode in a lithium battery was examined during lithium ion deinsertion and insertion by galvanostatic charge–discharge testing; PANI/LiCoO₂ nanocomposite materials exhibited better electrochemical performance by increasing the reaction reversibility and capacity compared to that of the pristine LiCoO₂ cathode. The best advancement has been observed for the PANI/LiCoO₂ nanocomposite 5 wt.% of aniline.     

Fabrication of MnS/GO/PANI nanocomposites on a highly conducting graphite electrode for supercapacitor application

We demonstrate a high surface area of manganese sulfide (MnS) nanoparticles via a simple solution method and investigated its morphology, physicochemical, and electrochemical studies. For the first time, we attempted to exploit the polymerization of aniline without adding HCl, as it is corrosive to the metal sulfide. Instead, the acidic group present on the graphene oxide surface plays a significant role to some extent as an acidic dopant in the polymerization process. This in-situ polymerization results in the uniform coverage of granular PANI on the entire MnS/GO nanocomposite, which enhances the interfacial interactions between PANI and MnS/GO nanoparticles. The introduction of graphene oxide (GO) to pristine MnS improved the specific capacitance, surface area, and average pore size. And incorporating PANI to MnS/GO leads to an increase in the interfacial interaction between the different pore sized nanoparticles giving enhanced specific capacitance. The specific capacitance for MnS/GO/PANI nanocomposite as measured by galvanostatic charge-discharge measurements was found to be 773 F/g at 1 A/g current density, and even at higher current density, it showed a specific capacitance of 484 F/g at 3.8 A/g. The specific capacitance obtained for MnS/GO/PANI nanocomposite from CV shows 822 F/g at 10 mV/s and 315 F/g at 200 mV/s. The combinatorial effects without destroying the metal sulfide nanostructure can provide an alternate route to design, promising electroactive nanocomposites is an ideal choice as a cost-effective, next-generation high-performance supercapacitor application.     

The Electrochemical Properties of Nanocomposite Films Obtained by Chemical In Situ Polymerization of Aniline and Carbon Nanostructures

Interactions between the π bonds in the aromatic rings of polyaniline (PANI) with carbon nanostructures (CNs) facilitate charge transfer between the two components. Different types of phenyleneamine‐terminated CNs, including carbon nano‐onions (CNOs) and single‐walled and multi‐walled carbon nanotubes (SWNTs and MWNTs, respectively), were prepared as templates, and the CN/PANI nanocomposites were easily prepared with uniform core–shell structures. By varying the ratio of the aniline monomers relative to the CNs in the in situ chemical polymerization process, the thickness of the PANI layers was effectively controlled. The morphological and electrical properties of the nanocomposite were determined and compared. The thickness and structure of the PANI films on the CNs were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), and infrared spectroscopy. TEM and SEM revealed that the composite films consisted of nanoporous networks of CNs coated with polymeric aniline. The electrochemical properties of the composites were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. These studies showed that the CN/PANI composite films had lower resistance than pure polymeric films of PANI, and the presence of CNs much improved the mechanical stability. The specific electrochemical capacitance of the CNO/PANI composite films was significantly larger than for pure PANI.     

手性聚苯胺纳米纤维的电化学制备

采用恒电位电聚合法制备了樟脑磺酸(CSA)掺杂的旋光异构性聚苯胺(PANI)纳米纤维. 用扫描电子显微镜(SEM)、 透射电子显微镜(TEM)、 紫外-可见吸收光谱(UV-Vis)和圆二色光谱(CD)对PANI纳米纤维的形貌和光学性质进行表征, 结合电聚合溶液胶束平均粒径和ζ电位的测定, 研究了具有旋光异构性PANI纳米纤维的形成机理和具有增强旋光异构性的原因. 所制备的PANI纳米纤维具有无双螺旋结构, 其形貌不随着苯胺浓度的改变而变化. 不同手性樟脑磺酸掺杂制备的PANI纳米纤维具有镜像对称的旋光异构性, 且具有较高的椭圆偏振率. 这种手性PANI纳米纤维的颜色和旋光性均可通过化学掺杂/去掺杂或电化学掺杂改变氧化还原态而呈现可逆变化.     

Hybrid polypyrrole/copper/graphene oxide nanocomposite films synthesized via potentiostatic deposition with enhanced photovoltaic properties

Novel ternary nanocomposites films of Polypyrrole/copper/graphene oxide (PPy/Cu/GO) showed enhanced optical and electronic properties. In this study, PPy/Cu/GO films were synthesized with different GO load (0.0, 0.4, 0.6, and 0.8 wt%) using electrochemical deposition technique. The structural, optical and electrical properties of the composites were evaluated using X-Ray Diffraction (XRD) spectroscopy, UV–visible spectroscopy, Scanning electron microscopy (SEM), Energy dispersive X-ray spectroscopy (EDX), and four-point probe methods. XRD results reveal that the GO was completely intercalated and dispersed uniformly in the nanocomposites. The results also revealed that the nanocomposite films are crystalline in nature, with distinct peaks corresponding to indexed miller indices. UV-visible analysis revealed that all of the nanocomposites showed good UV absorbance which was significant in the UV–Vis region of ≈450 nm. The energy band gap decreased with increase in GO load and was found within 3.46 to 2.25 eV, across the range of GO load which fall within the range of energy band gap for photovoltaic applications. The SEM results revealed that the nanocomposite films showed unevenly shaped structures with porous surface which increases with increasing GO loading, while the EDX result revealed the presence of carbon, oxygen nitrogen and copper as fundamental elements deposited. The nanocomposites' four-point probe analysis revealed slight increase in conductivity with low GO content. The incorporation of Cu and GO nanoparticles in PPy matrix provides a better balance and thus improved the photovoltaic properties of PPy/Cu/GO making them suitable for photovoltaic applications.     

Controllable Preparation of Polyaniline–Graphene Nanocomposites using Functionalized Graphene for Supercapacitor Electrodes

In order to explore the effect of graphene surface chemistry on electrochemical performance based on polyaniline–graphene hybrid material electrodes, four different polyaniline–graphene nanocomposites were fabricated with graphene oxide, reduced graphene oxide, aminated graphene and sulfonated graphene as carriers, respectively. The nanocomposites feature various structures and morphologies, which could be used to more deeply understand the morphology and structure effects caused by surface chemistry on electrochemical performance. The experimental results reveal that functionalized electronegative graphene was conducive to the vertical and neat growth of polyaniline (PANI) nanorods. The array architecture endowed the PANI–GS nanocomposite with a large ion‐accessible surface area and high‐efficiency electron‐ and ion‐transport pathways. Meanwhile, the introduction of sulfonic acid functional groups accelerated the redox reaction with doping and dedoping of the PANI. Thereby, the PANI–GS nanocomposite exhibited a high specific capacitance of 863.2 F g^?1 at a current density of 0.2 A g^?1 and the excellent rate capability of 67.4 % (581.6 F g^?1 at 5 A g^?1), which were much better than the other three nanocomposites produced.     

聚苯胺钡铁氧体纳米复合材料的制备、表征及性能

采用原位掺杂聚合法, 将聚苯胺(PANI)对粒径在60~80 nm的M型钡铁氧体颗粒(BaFe12O19)进行了包覆, 得到了具有棒状结构的复合材料. 通过X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)等测试手段对材料的形貌和结构进行了表征. 结果表明, PANI链段与BaFe12O19颗粒之间存在作用力. 使用振动磁强计和四探针法测定了复合材料的磁性能与电性能后发现, 饱和磁化强度与矫顽力均随聚苯胺含量的增加呈规律性下降趋势, 而电导率呈上升趋势. 复合材料的吸收特性测试结果表明, 该材料反射率小于-20 dB时, 带宽可以达到15.07 GHz. 同时详细地讨论了纳米复合材料的聚合机理及相互作用.     

氧化石墨掺杂的电化学活性自支撑聚苯胺膜

以氧化石墨（GO）为掺杂剂和模板,采用化学原位聚合法并通过调节苯胺单体和氧化石墨的质量比,合成了层状结构的聚苯胺/氧化石墨(PANI/GO)层状结构的自支撑膜。SEM和XRD研究表明,当苯胺单体与GO的质量比为67:1时,PANI/GO复合材料具有层间距~1.36 nm的层状结构,证实 GO的模板功能。XPS和FTIR研究表明PANI/GO复合材料中的典型的聚苯胺的掺杂态,进一步证实GO的掺杂功能。此外,电化学和热失重测量表明PANI/GO层状结构的自支撑膜呈现良好的热稳定性和高电化学活性.     

Preparation and magnetic properties of Zn-Cu-Cr-La ferrite and its nanocomposites with polyaniline

Nanosized Zn(0.6)Cu(0.4)Cr(0.5)Fe(1.5-x)La(x)O(4) (x=0 - 0.06) ferrites doped with La are synthesized by a rheological phase reaction method. Polyaniline (PANI)/ferrite nanocomposites are prepared by in situ polymerization method. The structure, morphology and ferromagnetic property of ferrite powders and nanocomposites are characterized by X-ray powder diffractometer (XRD), transmission electron microscope (TEM), Fourier transform infrared spectra (FTIR), UV-visible spectroscopy (UV), thermogravimetric analysis (TGA) and vibrating sample magnetometer (VSM). The results indicate that the PANI and nanosized ferrite powders can be combined effectively. The polymers can reduce the agglomeration of nanosized ferrite particles to some extent, which is good for the dispersedness and stabilization of nanoparticles. The PANI/ferrite nanocomposites under applied magnetic field exhibit the hysteretic loops of the ferromagnetic nature. The magnetic properties of nanocomposites are tailored by controlling the ferrite content.     

基于AuNPs/PANI/TNTs纳米复合材料的电化学检测妥布霉素的适配体传感器

本文提出了一种新型的检测妥布霉素的电化学适配体传感器,以差分脉冲伏安法（DPV）作为检测技术,亚甲基蓝作为电化学响应信号. 构建了以纳米复合材料金纳米粒子/聚苯胺/二氧化钛纳米管(AuNPs/PANI/TNTs)修饰玻碳电极的电极支架. 通过透射电子显微镜和X-射线光电子能谱对纳米复合材料进行详细的表征. 循环伏安图和电化学阻抗谱显示AuNPs/PANI/TNTs可以很好地增加电极的界面传导性能. DPV结果显示电流密度的响应和妥布霉素浓度之间存在一个很好的线性关系,并且得到一个宽广的检测范围为0.5 μmol·L^-1到70 μmol·L^-1. 本文提出的适配体基的传感器有很好的重复性和稳定性,作为一个潜在的手段可以应用在生物分析和医疗诊断中.     

以PS-b-P2VP为模板剂诱导调控聚苯胺形貌、尺寸及电化学性能

采用可逆加成-断裂链转移自由基聚合（RAFT）法合成了具有pH响应性的两亲嵌段共聚物聚苯乙烯-b-聚（2-乙烯基吡啶）（PS₁₀₁-b-P2VP₇₀），并以其胶束为"模板"，通过氧化聚合制备聚苯胺（PANI）.通过调节PS₁₀₁-b-P2VP₇₀胶束溶液的pH值，探究PANI颗粒形貌的可控调节及颗粒尺寸与PANI电化学性能之间的关系.利用凝胶渗透色谱（SEC）和核磁共振氢谱（¹H NMR）确定了PS₁₀₁-b-P2VP₇₀的分子量分布及结构；利用傅里叶变换红外光谱（FTIR）、透射电子显微镜（TEM）、粒度测试、循环伏安（CV）、计时电位（Chronopotentio-metry）及交流阻抗谱（EIS）对PANI结构、形貌和电化学性能进行了表征.结果表明"模板"法合成的PANI形貌尺寸得到了很好的控制，在pH ≤ 4时其尺寸随pH值的增加而减小；当pH=5时，模板剂中P2VP段疏水性的明显增大导致其胶束颗粒聚集为尺寸较大的聚集体，并使其诱导的PANI颗粒平均粒径显著增大；当pH=4时PANI颗粒在溶液中的平均粒径为141 nm，呈"串状"形貌且分散性最好.PANI具有快速充放电能力和良好的赝电容特性，随颗粒尺寸减小样品电化学性能增强.pH=4时样品电化学活性最好，循环伏安曲线面积最大，放电比容量最高，在电流密度为1 A/g时，其放电比容量可达1411.88 F/g，且该样品阻抗值最小.     

Nanocrystalline cellulose acetate (NCCA)/graphene oxide (GO) nanocomposites with enhanced mechanical properties and barrier against water vapor

Highly flexible nanocomposite films of nanocrystalline cellulose acetate (NCCA) and graphene oxide (GO) were synthesized by combining NCCA and GO sheets in a well-controlled manner. By adjusting the GO content, various NCCA/GO nanocomposites with 0.3–1 wt% GO were obtained. Films of these nanocomposites were prepared using the solvent casting method. Microscopic and X-ray diffraction (XRD) measurements demonstrated that the GO nanosheets were uniformly dispersed in the NCCA matrix. Mechanical properties of the composite films were also studied. The best GO composition of the samples tested was 0.8 wt%, giving tensile strength of 157.49 MPa, which represents a 61.92 % enhancement compared with NCCA. On the other hand, the composite films showed improved barrier properties against water vapor. This simple process for preparation of NCCA/GO films is attractive for potential development of high-performance films for electrical and electrochemical applications.     

Hierarchical nanocomposites of polyaniline scales coated on graphene oxide sheets for enhanced supercapacitors

The homogeneous polyaniline–graphene oxide (PANI-GO) nanocomposites were facilely assembled with a redox system in which cumene hydroperoxide (CHP) and iron dichloride (FeCl₂) acted as oxidant and reductant, respectively. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images showed that PANI scales coated uniformly on the surface of GO sheets owing to the synergistic effect between the PANI and GO. The obtained PANI-GO nanocomposites exhibited improved electrochemical performance as an electrode material for supercapacitors compared with the pure PANI. The specific capacitance of the PANI-GO nanocomposites was high up to 308.3 F g^?1, much higher than that of the pure PANI with specific capacitance of 150 F g^?1 at a current density of 1 A g^?1 in 2 M H₂SO₄ electrolyte. The Raman and XPS results illustrated that enhanced electrochemical performance might be attributed to the π-π conjugation between the PANI and GO sheets.     

Synthesis and Characterization of PANI/ZnO Nanocomposites

This paper presents our results on the successful fabrication of HCl‐doped polyaniline (PANI)/ZnO nanocomposites via an electrochemical synthesis route. Different weight percents of ZnO nanoparticles were uniformly dispersed in the PANI matrix. The interaction between the dispersed ZnO nanoparticle and PANI was studied using X‐ray diffraction, ultraviolet–visible absorption spectroscopy, photoluminescence (PL) spectroscopy, X‐ray photoelectron spectroscopy, atomic force microscopy, thermogravimetry, and transmission electron microscopy. It is shown that the doping state of the PANI/ZnO nanocomposite is highly improved as compared to that of PANI. The dispersed PANI/ZnO nanocomposites exhibit enhanced PL behavior and thermal stability.     

Doping polyaniline with pristine carbon nanotubes into electroactive nanocomposite in neutral and alkaline media

This study describes a facile but effective route to synthesis of electroactive polyaniline (PANI) in the neutral and alkaline media simply with pristine single-walled carbon nanotubes (SWNTs) as the dopant. Cyclic voltammetry (CV) studies reveal that the SWNT/PANI nanocomposite processes a good electrochemical activity in the neutral and alkaline media. Control experiments with PANI mixed with heat-treated SWNTs imply that the electrochemical properties of the SWNT/PANI nanocomposite in the neutral and alkaline media do not result from the presence of carboxylic groups at SWNTs themselves, and in turn show that the pristine SWNTs can be potentially used as a new and effective dopant to preserve the electrochemical property of PANI in the neutral and alkaline media. This property of the SWNT/PANI nanocomposite is reasonably envisaged to be promising for electrochemical investigations and electroanalytical applications, especially for the development of electrochemical sensors, biosensors and biofuel cells.     

Polyaniline‐Stabilized Intertwined Network‐like Ferrocene/Graphene Nanoarchitecture for Supercapacitor Application

The present work highlights the effective H–π interaction between metallocenes (ferrocene; Fc) and graphene and their stabilization in the presence of polyaniline (PANI) through π–π interactions. The PANI‐stabilized Fc@graphene nanocomposite (FcGA) resembled an intertwined network‐like morphology with high surface area and porosity, which could make it a potential candidate for energy‐storage applications. The relative interactions between the components were assessed through theoretical (DFT) calculations. The specific capacitance calculated from galvanostatic charging/discharging indicated that the PANI‐stabilized ternary nanocomposite exhibited a maximum specific capacitance of 960 F g⁻ at an energy density of 85 Wh Kg⁻¹ and a current density of 1 A g⁻. Furthermore, electrochemical impedance spectroscopy (EIS) analysis confirmed the low internal resistance of the as‐prepared nanocomposites, which showed improved charge‐transfer properties of graphene after incorporation of Fc and stabilization with PANI. Additionally, all electrodes were found to be stable up to 5000 cycles with a specific capacitance retention of 86 %, thus demonstrating the good reversibility and durability of the electrode material.     

静电纺丝法制备聚丙烯腈/聚苯胺复合纳米纤维及其表征

利用静电纺丝技术,以聚丙烯腈(PAN)和苯胺(ANI)为前驱物,用过硫酸胺(APS)溶液在低温下缓慢氧化聚合,制备了PAN/PANI复合纳米纤维,直径约500 nm.通过扫描电子显微镜(SEM)、红外光谱(FTIR)、X射线衍射(XRD)和激光拉曼(RAMAN)光谱仪等测试手段对材料的形貌和结构进行了表征.探讨了材料制备过程中影响纤维形貌、尺寸、均匀度的因素和PANI含量对复合纤维导电性能的影响,结果表明,PAN浓度、ANI的加入量和电压是影响纤维特性的主要因素;PANI在PAN基体中呈纳米尺寸分布,复合纳米纤维具有良好的导电性能,导电率可达10-2S/cm.     

Synthesis and characterization of C60/polyaniline composites from interfacial polymerization

C₆₀/polyaniline (PANI) nanocomposites have been synthesized by the oxidative polymerization of aniline with ammonium peroxydisulfate in the presence of C₆₀ by using an interfacial reaction. When compared with the pure PANI nanofibers from the similar process, the diameter of the obtained C₆₀/PANI nanofibers was increased because of the encapsulation of C₆₀ into PANI during aniline polymerization, which resulted from the charge‐transfer interactions between C₆₀ and aniline fragment in PANI. In addition, the resulting C₆₀/PANI nanocomposites synthesized from the low initial C₆₀/aniline molar ratio (less than 1:25) showed the homogenous morphology composed of fiber network structures, which has an electrical conductivity as high as 1.1 × 10^?4 S/cm. However, the C₆₀/PANI nanocomposites from the higher initial C₆₀/aniline molar ratio (more than 1:15) showed the nonuniformly distributed morphology, and the electrical conductivity was decreased to 3.5 × 10^?5 S/cm. Moreover, the C₆₀/PANI nanocomposites from the interfacial reaction showed a higher value of electrical conductivity than the mechanically mixed C₆₀/PANI blends with the same C₆₀ content, because of the more evenly distributed microstructures. FTIR, UV–vis, and CV data confirmed the presence of C₆₀ and the significant charge‐transfer interactions in the resultant nanocomposites, which was responsible for the morphology development of the C₆₀/PANI and the variation of the electrical conductivity. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Electrospun poly(3‐hexylthiophene)/poly(ethylene oxide)/graphene oxide composite nanofibers: effects of graphene oxide reduction

In this article, we report on the production by electrospinning of P3HT/PEO, P3HT/PEO/GO, and P3HT/PEO/rGO nanofibers in which the filler is homogeneously dispersed and parallel oriented along the fibers axis. The effect of nanofillers' presence inside nanofibers and GO reduction was studied, in order to reveal the influence of the new hierarchical structure on the electrical conductivity and mechanical properties. An in‐depth characterization of the purity and regioregularity of the starting P3HT as well as the morphology and chemical structure of GO and rGO was carried out. The morphology of the electrospun nanofibers was examined by both scanning and transmission electron microscopy. The fibrous nanocomposites are also characterized by differential scanning calorimetry to investigate their chemical structure and polymer chains arrangements. Finally, the electrical conductivity of the electrospun fibers and the elastic modulus of the single fibers are evaluated using a four‐point probe method and atomic force microscopy nanoindentation, respectively. The electrospun materials crystallinity as well as the elastic modulus increase with the addition of the nanofillers while the electrical conductivity is positively influenced by the GO reduction. Copyright © 2016 John Wiley & Sons, Ltd.     

Synthesis of PANI and Study of Morphology in the Process of Polymerization

The polyaniline micro/nanostructure was prepared by a self‐assembly process with molybdic acid as dopants in the presence of ammonium persulfate as the oxidant. It was found that the morphology of PANI micro/nanostructure was affected by the concentration of the dopant, that is, the morphology of PANI changed from nanofibers to co‐existence of nanofibers and microspheres as the molar ratio of molybdic acid to aniline varied from 0.01 to 1.5. Under the same condition it was also found that the conductivity value of PANI enhanced from 4.58×10^?3 S·cm^?1 to 3.8×10^?1 S·cm^?1. The structure of PANI was characterized by FTIR and XRD which confirmed the presence of the molybdic acid in the PANI. The electrochemical characteristics of the PANI nanofibers were investigated by means of cyclic voltammetry. The morphology of PANI in the process of polymerization was characterized by SEM. It was found that when the molar ratio of molybdic acid to aniline was 0.3, the morphology of PANI was co‐existence of nanofibers and microspheres and the formation of microspheres was ahead of the nanofibers.