Synthesis and properties of poly(ether imide)s based on the bis(ether anhydride)s from hydroquinone and its derivatives

Four bis(ether anhydride)s, 4,4′‐(1,4‐phenylenedioxy)diphthalic anhydride (IV), 4,4′‐(2,5‐tolylenedioxy)‐diphthalic anhydride (Me‐IV), 4,4′‐(2‐chloro‐1,4‐phenylenedioxy)diphthalic anhydride (Cl‐IV), and 4,4′‐(2,5‐biphenylenedioxy)diphthalic anhydride (Ph‐IV), were prepared in three steps starting from the nucleophilic nitrodisplacement reaction of 4‐nitrophthalonitrile with the potassium phenoxides of hydroquinone and various substituted hydroquinones such as methylhydroquinone, chlorohydroquinone, and phenylhydroquinone in N,N‐dimethylformamide, followed by alkaline hydrolysis and dehydration. Four series of poly(ether imide)s were prepared from bis(ether anhydride)s with various aromatic diamines by a classical two‐step procedure. The inherent viscosities of the intermediate poly(amic acid)s were in the range of 0.40–2.63 dL/g. Except for those derived from p‐phenylenediamine and benzidine, almost all the poly(amic acid)s could be solution‐cast and thermally converted into transparent, flexible, and tough polyimide films. Introduction of the chloro or phenyl substituent leads to a decreased crystallinity and an increased solubility of the polymers. The glass transition temperatures (T_g) of these polyimides were recorded in the range of 204–263°C. In general, the methyl‐ and chloro‐substituted polyimides exhibited relatively higher T_gs, whereas the phenyl‐substituted ones exhibited slightly lower T_gs compared to the corresponding nonsubstituted ones. Thermogravimetric analysis (TG) showed that 10% weight loss temperatures of all the polymers were above 500°C either in nitrogen or in air. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 665–675, 1999     

Synthesis and characterization of aromatic poly(ether sulfone imide)s derived from sulfonyl bis(ether anhydride)s and aromatic diamines

Two sulfonyl group-containing bis(ether anhydride)s, 4,4′-[sulfonylbis(1,4-phenylene)dioxy]diphthalic anhydride ( IV ) and 4,4′-[sulfonylbis(2,6-dimethyl-1,4-phenylene)dioxy]diphthalic anhydride (Me- IV ), were prepared in three steps starting from the nucleophilic nitrodisplacement reaction of the bisphenolate ions of 4,4′-sulfonyldiphenol and 4,4′-sulfonylbis(2,6-dimethylphenol) with 4-nitrophthalonitrile in N,N-dimethylformamide (DMF). High-molar-mass aromatic poly(ether sulfone imide)s were synthesized via a conventional two-stage procedure from the bis(ether anhydride)s and various aromatic diamines. The inherent viscosities of the intermediate poly(ether sulfone amic acid)s were in the ranges of 0.30–0.47 dL/g for those from IV and 0.64–1.34 dL/g for those from Me- IV. After thermal imidization, the resulting two series of poly(ether sulfone imide)s had inherent viscosities of 0.25–0.49 and 0.39–1.19 dL/g, respectively. Most of the polyimides showed distinct glass transitions on their differential scanning calorimetry (DSC) curves, and their glass transition temperatures (T_g) were recorded between 223–253 and 252–288°C, respectively. The results of thermogravimetry (TG) revealed that all the poly(ether sulfone imide)s showed no significant weight loss before 400°C. The methyl-substituted polymers showed higher T_g's but lower initial decomposition temperatures and less solubility compared to the corresponding unsubstituted polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1649–1656, 1998     

Synthesis and characterization of new poly[phenylquinoxaline(ether)imides]

A series of new aromatic poly[phenylquinoxaline(ether)imides] were synthesized by solution polycondensation of aromatic diamines containing preformed phenylquinoxaline groups with dianhydrides having ether linkages and isopropylidene or hexafluoroisopropylidene units. All polymers are readily soluble in polar organic solvents (N-methylpyrrolidinone, DMF, dimethylacetamide) and in less polar liquids such as chloroform. Very thin coatings were deposited onto silicon wafers. According to atomic force microscopy, they had a smooth, pinhole-free surface. The polymers showed high thermal stability with decomposition temperatures above 470 °C and glass transition temperatures in the range of 210–238 °C, being thus characterized by a large gap between the glass transition and decomposition temperatures.Based on the report presented at the International Conference Modern Trends in Organoelement and Polymer Chemistry dedicated to the 50th year anniversary of the A. N. Nesmeyanov Institute of Organoelement Compounds of the Russian Academy of Sciences (Moscow, May 30–June 4, 2004).Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 9, pp. 1952–1957, September, 2004.     

Synthesis and physical characterization of model hard segments based on diphenyl methane diisocyanate and hydroquinone bis(2‐hydroxyethyl) ether

Hard segment model compounds based on diphenyl methane diisocyanate (MDI) and hydroquinone bis(2‐hydroxyethyl) ether (HQE) were synthesized; these models were end‐capped with ethanol (E) or 2‐phenoxyethanol (F). NMR spectroscopy and GPC analysis confirm the expected structure: R‐(MDI‐HQE)_p−1‐MDI‐R′ (where p = 1, 2, 3; R, R′ = E, and/or F if p =1). Intrinsic viscosity revealed a Mark–Houwink exponent of 0.73, and a value of 4.76 × 10⁻² cc/g was obtained for K; applying the Mark–Houwink equation on a MDI–HQE polymer a MW of 2650 was calculated, while a value of 2872 was achieved by GPC analysis using a specifically drawn calibration curve. Thermal analysis reveals the crystalline nature of these models and the increase of melting temperature with the number of repeating units; an extrapolated value ranging from 274 to 361 °C, depending on selected structure for the first term of the oligourethane series, was calculated for the polymer using the Flory's equation accounting for chain end defects. Calorimetric traces and GPC analyses on annealed samples show an extensive degradation of models having higher melting temperature (p > 1), in this case a broad high molecular weight mixture, which contains also significant amounts of short oligourethanes or byproducts, was generally observed. A comparison of the melting behavior of this series with similar models based on MDI but with a different chain extender (1,4‐butanediol, BDO) seems to indicate an increase in the melting temperature. This evidence can be tentatively attributed to the longer aromatic sequences present in the hydroquinone containing models. The investigation of the characteristics of these hard models gives predictive information useful for better understanding properties/structure relationships of polyurethane elastomers containing similar hard sequences. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1473–1487, 1999     

聚醚醚酮醚酮的合成与表征

聚醚醚酮（ＰＥＥＫ）自工业化以来［１］，由于其优异的性能已在机械、航天等领域得到广泛应用．各种聚芳醚酮类聚合物相继被开发出来．但以亲电缩聚路线制备聚醚醚酮醚酮（ＰＥＥＫＥＫ）的报道较少［２］．本文以二苯醚和４－氟苯甲酰氯为主要反应试剂，采取付氏酰基化...     

Synthesis and properties of poly(ether imide)s based on a benzonorbornane bis(ether anhydride)

A novel bis(ether anhydride) monomer, 3,6‐bis(3,4‐dicarboxyphenoxy)benzonorbornane dianhydride, was synthesized from the nitro displacement of 4‐nitrophthalonitrile with 3,6‐dihydroxybenzonorbornane in the presence of potassium carbonate, followed by the alkaline hydrolysis of the intermediate bis(ether dinitrile) and the cyclodehydration of the resulting bis(ether diacid). A series of poly(ether imide)s bearing pendant norbornane groups were prepared from the bis(ether anhydride) with various aromatic diamines via a conventional two‐stage process that included ring‐opening polyaddition to form the poly(amic acid)s followed by thermal imidization to the poly(ether imide)s. The inherent viscosities of the poly(amic acid) precursors were 0.81–1.81 dL/g. The poly(ether imide) with m‐phenylenediamine as a diamine showed good organosolubility. Most of the cast poly(ether imide) films have had high tensile strengths and moduli. The glass‐transition temperatures of these poly(ether imide)s, except for those from rigid p‐phenylenediamine and benzidine, were recorded between 211 and 246 °C by differential scanning calorimetry. The softening temperatures of all the poly(ether imide) films stayed within 210–330 °C according to thermomechanical analysis. No polymers showed significant decomposition before 500 °C in a nitrogen or air atmosphere. A comparative study of the properties with the corresponding poly(ether imide)s without pendant substituents was also made. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1712–1725, 2002     

Synthesis of high molecular weight poly(ether ketone)s by polycondensation of activated bis(aryl chloride)s with bisphenolates

The ability to achieve high molecular weight poly(ether ketone)s from the polycondensation of bis(aryl chloride)s with bis(phenolate)s has been consistently demonstrated. The polymerizations presented here help to delineate for specific bis(aryl chloride)/bisphenolate pairs the reaction conditions required to obtain high molecular weight polymers. Polycondensation of 1,3-bis(4-chlorobenzoyl)-5-tert-butylbenzene ( 6 ) and 2,2′-bis(4-chlorobenzoyl)-biphenyl ( 15 ) with various bisphenolates as well as of 2,2′-bis(4-hydroxyphenoxy)biphenyl ( 33 ) with 4,4′-dichlorobenzophenone ( 41 ) and 1,3-bis(4-chlorobenzoyl)benzene ( 43 ) were used as representative model systems to select reaction conditions that led to high molecular weight polymers. © 1995 John Wiley & Sons, Inc.     

Synthesis and properties of novel aromatic poly(o-hydroxy amide)s and polybenzoxazoles based on the bis(ether benzoyl chloride)s from hydroquinone and its methyl-, tert-butyl-, and phenyl-substituted derivatives

Four series of poly(o-hydroxy amide)s were prepared by the low-temperature solution polycondensation of the bis(ether benzoyl chloride)s extended from hydroquinone and its methyl-, tert-butyl-, or phenyl-substituted derivatives with three bis(o-aminophenol)s. Most of the poly(o-hydroxy amide)s displayed an amorphous nature, were readily soluble in various polar solvents such as N,N-dimethylacetamide (DMAc), and could be solution-cast into flexible and tough films. These poly(o-hydroxy amide)s had glass transition temperatures (T_g) in the range of 152–185°C and could be thermally cyclodehydrated into the corresponding polybenzoxazoles approximately in the region of 200–400°C, as evidenced by the DSC thermograms. The thermally converted benzoxazole polymers exhibited T_gs in the range of 215–247°C and did not show significant weight loss before 500°C either in nitrogen or in air. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2129–2136, 1999     

Synthesis and properties of novel aromatic polyhydrazides and poly(amide–hydrazide)s based on the bis(ether benzoic acid)s from hydroquinone and substituted hydroquinones

4,4′‐(1,4‐Phenylenedioxy)dibenzoic acid as well as the 2‐methyl‐, 2‐tert‐butyl‐, or 2‐phenyl‐substituted derivatives of this dicarboxylic acid were synthesized in two main steps from p‐fluorobenzonitrile and hydroquinone or its methyl‐, tert‐butyl‐, or phenyl‐substituted derivatives. Polyhydrazides and poly(amide–hydrazide)s were prepared from these bis(ether benzoic acid)s or their diacyl chlorides with terephthalic dihydrazide, isophthalic dihydrazide, or p‐aminobenzoyl hydrazide by means of the phosphorylation reaction or low‐temperature solution polycondensation. Most of the hydrazide polymers and copolymers are amorphous and readily soluble in various polar solvents such as N‐methyl‐2‐pyrrolidone (NMP) and dimethyl sulfoxide. They could be solution‐cast into transparent, flexible, and tough films. These polyhydrazides and poly(amide–hydrazide)s had T_gs in the range of 167–237°C and could be thermally cyclodehydrated into the corresponding poly(1,3,4‐oxadiazole)s and poly(amide–1,3,4‐oxadiazole)s approximately in the region of 250–350°C, as evidenced by the DSC thermograms. All the tert‐butyl‐substituted oxadiazole polymers and those derived from isophthalic dihydrazide were organic soluble. The thermally converted oxadiazole polymers exhibited T_gs in the range of 208–243°C and did not show significant weight loss before 450°C either in nitrogen or in air. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1169–1181, 1999     

New light‐colored poly(ether imide)s based on 2,5‐di‐tert‐butylhydroquinone bis(ether anhydride) and aromatic diamines

A series of poly(ether imide)s (PEIs), III _a–k , with light color and good physical properties were prepared from 1,4‐bis(3,4‐dicarboxypheoxy)‐2,5‐di‐tert‐butylbenzene dianhydride ( I ) with various aromatic diamines ( II _a–k ) via a conventional two‐stage procedure that included a ring‐opening polyaddition to yield poly(amic acid)s (PAA), followed by thermal imidization to the PEI. The intermediate PAA had inherent viscosities in the range of 1.00–1.53 dL g^?1. Most of the PEIs showed excellent solubility in chlorinated solvents such as dichloromethane, chloroform, and m‐cresol, but did not easily dissolve in dimethyl sulfoxide and amide‐type polar solvents. The III series had tensile strengths of 96–116 MPa, an elongation at break of 7–8%, and initial moduli of 2.0–2.5 GPa. The glass‐transition temperatures (T_g) and softening temperatures (T_s's) of the III series were recorded between 232 and 285 °C and 216–279 °C, respectively. The decomposition temperatures for 10% weight loss all occurred above 511 °C in nitrogen and 487 °C in air. The III series showed low dielectric constants (2.71–3.54 at 1 MHz), low moisture absorption (0.18–0.66 wt %), and was light‐colored with a cutoff wavelength below 380 nm and a low yellow index (b^*) values of 7.3–14.8. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1270–1284, 2005     

Synthesis and characterization of azo dyestuff based on bis(2-hydroxyethyl) terephthalate derived from depolymerized waste poly(ethylene terephthalate) fibers

This work aimed at effectively utilizing the chemically depolymerized waste poly(ethylene terephthalate)(PET) fibers into useful products for the textile industry.PET fibers were glycolytically degraded by excess ethylene glycol as depolymerizing agent and zinc acetate dihydrate as catalyst.The glycolysis product,bis(2-hydroxyethyl) terephthalate(BHET),was purified through repeated crystallization to get an average yield above 80%.Then,BHET was nitrated,reduced,and azotized to get diazonium salt.Finally,the produced diazonium salt was coupled with 1-(4-sulfophenyl)-3-methyl-5-pyrazolone to get azo dyestuff.The structures of BHET and azo dyestuff were identified by FT1 R and ~1H NMR spectra and elemental analysis.Nylon filaments dyed by the synthesized azo dyestuff with the dye bath pH from 4.14 to 5.88 showed bright yellow color.The performances of the dyestuff were described with dye uptake,color fastness,K/S,L~*,a~*,b~*.and △E~* values.     

Synthesis and properties of new poly(ether sulfone)amides

High molecular-weight aromatic polyamides were obtained from 1,5- and 2,6-bis-(4′-carboxy-4-phenylenoxy-sulfonyl)naphthalene by direct polycondensation reaction in N-methyl-2-pyrrolidone with various aromatic diamines, using triphenyl phosphite and pyridine as condensing agents. The polymers were characterized by elemental analysis, thermogravimetric analysis, differential scanning calorimetry, and infrared analysis. The polyamides, obtained in quantitative yield, possessed inherent viscosities in the range 0.42–1.70 dL/g, glass transition temperatures between 245–310°C, and 10% weight loss temperatures in nitrogen and air above 435 and 424°C, respectively. Most of the polymers were soluble in aprotic solvents. The effect of the structure on properties, such as solubility, T_g, and thermal behavior, were also studied. © 1996 John Wiley & Sons, Inc.     

Synthesis and characterization of new poly(arylene ether)s containing heterocyclic units. II.

A series of new poly(arylene ether)s, containing naphthalene, pyridine, and quinoline units have been prepared by solution condensation polymerization. The synthesis involves nucleophilic displacement of aromatic dihalides with aromatic potassium bisphenates in an anhydrous dipolar aprotic solvent at elevated temperatures. The polymers, having inherent viscosity from 0.24 to 1.32 dL/g, were obtained in quantitative yield, have excellent thermal stability as shown by 10% weight loss temperatures in nitrogen and air (above 450 and 430°C, respectively) and high glass transition temperatures (in the range of 150–220°C). The introduction of quinoline moieties in the polymer backbone positively influences the thermal properties, such as high T_g/T_m ratios. © 1995 John Wiley & Sons, Inc.     

Synthesis and optical properties of novel soluble and optically transparent semifluorinated poly (ether imide)s

A fluorinated diamine monomer containing flexible ether linkage and bulky trifluoromethyl substituents, namely, bis(4‐amino‐2‐trifluoromethylphenyl) ether (a), is employed to react with nonfluorinated 1,4‐bis(3,4‐dicarboxyphenoxy) benzene dianhydride (3) and CF₃‐free 2,2‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl] propane dianhydride (4), respectively, to prepare 2 novel soluble and optically transparent semi‐fluorinated poly (ether imide)s (PEIs; 3a and 4a). Compared with the corresponding PEIs based on nonfluorinated 4,4′‐diaminodiphenyl ether (b) and CF₃‐free pyromellitic dianhydride (5), the novel semifluorinated PEIs 3a and 4a not only display better solubility in some organic solvents and higher optical transparency with cutoff absorption wavelength (λ₀) below 370 nm but also maintain outstanding mechanical properties and thermal stability. 3a and 4a have tensile strength beyond 80 MPa and possess glass‐transition temperatures (T_g) beyond 210°C, coupled with the temperatures of 5% weight loss (T_5%) exceeding 500°C. It is also found that 3a and 4a exhibit contact angles against water beyond 110° and water absorptions below 0.8% together with dielectric constants less than 3.2.     

A novel route to poly(2-hydroxyethyl methacrylate) and its amphiphilic block copolymers

The vinyl of the ester group of 2-vinyloxyethyl methacrylate was first selectively reacted with acetic acid to obtain 2-[1-(acetoxy)ethoxy]ethyl methacrylate ( 2 ). This protected monomer was subjected to anionic polymerization in tetrahydrofuran at −60°C in the presence of LiCl, using 1,1-diphenylhexyllithium as initiator. The molecular weight of the polymer could thus be controlled and a narrow molecular weight distribution obtained. The protecting group, 1-(acetoxy)ethyl, could be easily eliminated (by quenching the polymerization reaction with methanol and water) to generate poly(2-hydroxyethyl methacrylate) (poly(HEMA)). Block copolymers were also prepared by the sequential anionic polymerization of MMA and 2 or styrene and 2 . They possess narrow molecular weight distributions, and controlled molecular weights and compositions. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1865–1872, 1998     

Synthesis of poly(silyl ether)s containing pendant chloromethyl groups by the polyaddition of bis(oxetane)s with dichlorosilanes

The polyaddition of bis(3‐ethyl‐3‐oxetanylmethyl) terephthalate (BEOT) with dichlorodiphenylsilane (CPS) using tetrabutylammonium bromide (TBAB) as a catalyst proceeded under mild reaction conditions to afford a polymer containing silicon atoms in the polymer main chain. A poly(silyl ether) (P‐1) with a high molecular weight (M_n = 53,200) was obtained by the reaction of BEOT with CPS in the presence of 5 mol % of TBAB in toluene at 0 °C for 1 h and then at 50 °C for 24 h. The structure of the resulting polymer was confirmed by IR and ¹H NMR spectra. Furthermore, it was proved that the polyaddition of certain bis(oxetane)s with dichlorosilanes proceeds smoothly to give corresponding poly(silyl ether)s with TBAB as the catalyst. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2254–2259, 2000     

Synthesis and characterization of poly(ether naphthalimide)s

A series of new poly(ether imide)s containing the naphthalimide moiety were prepared from bis(4-fluorobenzoyl)naphthalimides and several bisphenols by aromatic nucleophilic displacement polymerization. These polyimides had inherent viscosities in the range of 0.31–1.04 dL/g in chloroform and glass transition temperatures of 283.0–341.6°C by differential scanning calorimetry. The onset temperature for 5% weight loss for all the polymers was over 448°C, as assessed by thermogravimetry at a heating rate 10°C/min in nitrogen. In addition, these novel polyimides exhibited good solubility in organic solvents including N-methyl-2-pyrrolidone, N,N-dimethylformamide, N,N-dimethylacetamide, 1,1,2,2-tetrachloroethane and chloroform. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3227–3231, 1999     

Synthesis and characterization of new poly(ether amide)s based on a new cardo monomer

A new cardo diamine monomer 3, 3‐bis‐[4‐{2′trifluoromethyl 4′‐(4″‐aminophenyl) phenoxy} phenyl]‐2‐phenyl‐2, 3‐dihydro‐isoindole‐1‐one ( 4 ) has been synthesized from potentially cheap phenolphthalein as the starting material. This diamine was used for the synthesis of a new poly(ether amide) and two co‐poly(ether amide)s using 4, 4′‐diaminodiphenyl ether (ODA) as co‐monomer by direct solution polycondensation with 5‐t‐butyl iso‐phthalic acid. These new polymers showed inherent viscosities of 0.48–0.62 dL g^?1. The resulting poly(ether amide) and co‐poly(ether amide)s were readily soluble in polar aprotic solvents like NMP, DMF, DMAc, DMSO, and pyridine. The polymers have been fully characterized by ¹H and ¹³C NMR, FTIR spectroscopy, and elemental analysis. These polymers showed glass transition temperatures in the range of 267–310°C. Thermogravimetric analysis indicated high thermal stability of these polymers at 5 and 10% weight loss temperature in air above 357°C and 419°C, respectively. The poly(ether amide) films cast from DMAc were flexible with tensile strength up to 91 MPa, elongations at break up to 11%, and modulus of elasticity up to 1.82 GPa. X‐ray diffraction measurements indicate the amorphous nature of the poly(ether amide)s. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and characterization of poly(ethylene glycol) methyl ether endcapped poly(ethylene terephthalate)

Linear and branched poly(ethylene terephthalate) (PET) copolymers with polyethylene glycol) (PEG) methyl ether (700 or 2000 g/mol) end groups were synthesized using conventional melt polymerization. DSC analysis demonstrated that low levels of PEG end groups accelerated PET crystallization. The incorporated PEG end groups also decreased the crystallization temperature of PET dramatically, and copolymers with a high content of PEG (>17.6 wt%) were able to crystallize at room temperature. Rheological analysis demonstrated that the presence of PEG end groups effectively decreased the melt viscosities and facilitated melt processing. XPS and ATR-FTIR revealed that the PEG end groups tended to aggregate on the surface, and the surface of compression molded films containing 34.0 wt% PEG were PEG rich (85 wt% PEG). PEG end-capped PET (34.0 wt% PEG) and PET films were immersed into a fibrinogen solution (0.7 mg/mL BSA) for 72 h to investigate the propensity for protein adhesion. XPS demonstrated that the concentration of nitrogen (1.05%) on the surface of PEG endcapped PET film was statistically lower than PET (7.67%). SEM analysis was consistent with XPS results, and revealed the presence of adsorbed protein on the surface of PET films.     

Synthesis and characterization of new fluorene‐based poly(ether imide)s

A novel bis(ether anhydride) monomer, 9,9‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]fluorene dianhydride (4), was synthesized from the nitrodisplacement of 4‐nitrophthalonitrile by the bisphenoxide ion of 9,9‐bis(4‐hydroxyphenyl)fluorene (1), followed by alkaline hydrolysis of the intermediate tetranitrile and dehydration of the resulting tetracarboxylic acid. A series of poly(ether imide)s bearing the fluorenylidene group were prepared from the bis(ether anhydride) 4 with various aromatic diamines 5a–i via a conventional two‐stage process that included ring‐opening polyaddition to form the poly(amic acid)s 6a–i followed by thermal cyclodehydration to the polyimides 7a–i. The intermediate poly(amic acid)s had inherent viscosities in the range of 0.39–1.57 dL/g and afforded flexible and tough films by solution‐casting. Except for those derived from p‐phenylenediamine, m‐phenylenediamine, and benzidine, all other poly(amic acid) films could be thermally transformed into flexible and tough polyimide films. The glass transition temperatures (T_g) of these poly(ether imide)s were recorded between 238–306°C with the help of differential scanning calorimetry (DSC), and the softening temperatures (T_s) determined by thermomechanical analysis (TMA) stayed in the range of 231–301°C. Decomposition temperatures for 10% weight loss all occurred above 540°C in an air or a nitrogen atmosphere. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1403–1412, 1999