Robust superhydrophobic candle soot and silica composite sponges for efficient oil/water separation in corrosive and hot water

Journal of Sol-Gel Science and Technology - The superhydrophobic sponges were fabricated through dip-coating candle soot (?CS) and SiO2 nanoparticles on polyurethane (P?U) sponges....     

Hollow-fiber membranes coated with polymerizable bicontinuous microemulsions

A new method has been successfully employed to prepare hollow-fiber membranes by coating and polymerizing bicontinuous microemulsions onto the internal surfaces of hollow-fiber membranes. The bicontinuous microemulsion consisting of water, a polymerizable zwitterionic surfactant of acryloyloxyundecyl dimethylammonio acetate, methyl methacrylate, and 2-hydroxylethyl methacrylate (HEMA) can form a transparent polymer thin film after polymerization. The hollow-fiber membranes as the supports for microemulsion coatings were fabricated from the spinning solution of polyethersulfone/diethylene glycol/N-methyl-2-pyrrolidone. The microemulsion coated hollow-fiber membranes were evaluated by the separation efficiency and the permeation rate of polyethylene glycol (PEG) solutions. The performance of coated membrane on the PEG separation is strongly dependent on the concentration of HEMA and water in precursor bicontinuous microemulsions. The pore size of the hollow-fiber membranes can be regulated between about 2 to 40 nm by varying the composition of precursor bicontinuous microemulsions. The characteristics of the coated membranes is believed to be directly related to the bicontinuous structures of precursor bicontinuous microemulsions. The use of polymerizable bicontinuous microemulsions enable one to better control the microstructures of coated membranes via in situ polymerization.     

Modification of porous poly(vinylidene fluoride) membrane using amphiphilic polymers with different structures in phase inversion process

Three kinds of amphiphilic polymers, including the tri-block copolymer of (polyethylene oxide)–(polypropylene oxide)–(polyethylene oxide) (I, EPTBP), the comb-like copolymer of polysiloxane with polyethylene oxide and polypropylene oxide side chains (II, ACPS) and the hyperbranched star copolymer of polyester-g-methoxyl polyethylene glycol (III, HPE-g-MPEG), were blended with PVDF to fabricate porous membranes via a phase inversion process, respectively, and the effects of the different structures of the amphiphilic polymers on the properties of the blend membranes were compared. The membranes were characterized by scanning electron microscopy (SEM), elemental analysis, X-ray photoelectron spectroscopy (XPS) analysis, mercury porosimetry, water contact angle measurements, etc. The anti-fouling properties of the prepared membranes were evaluated by static and dynamic bovine serum albumin (BSA) adsorptions. Specially, the stabilities of these amphiphilic polymers in the final membranes were estimated by continuous leaching tests. At the same time, the properties of the membranes using the amphiphilic polymers as modifiers were compared with those of the membrane using poly(ethylene glycol) (PEG) as modifier.     

Studies on cellulose acetate-carboxylated polysulfone blend ultrafiltration membranes--Part I

Hydrophilic polysulfone ultrafiltration (UF) membranes were prepared from blends of cellulose acetate with carboxylated polysulfone of 0.14 degree of carboxylation. The effects of blend polymer composition on compaction, pure water flux, water content and membrane hydraulic resistance (R_m), have been investigated to evaluate the performance of the membranes. The performance of the blend membranes of various blend polymer compositions were compared with that of membranes prepared from pure cellulose acetate and blends of cellulose acetate and pure polysulfone. The hydrophilic cellulose acetate-carboxylated polysulfone blend UF membranes showed better performance compared to membranes prepared from pure cellulose acetate and blends of cellulose acetate and pure polysulfone.     

13C NMR study of the intermolecular interactions in the polyethylene glycol-cellulose acetate-solvent system

As a result of measuring the spin-lattice relaxation rates of¹³C nuclei of polyethylene glycol in different solvents in the presence of cellulose acetates, it was found that polyethylene glycol forms H complexes with cellulose acetate in nonaqueous solvents, and the probability of binding increases with a decrease in the molecular weight of the polyethylene glycol. The formation of H complexes results in an effect of inversion of the mobility of the polyethylene glycol molecules of different weights in concentrated solutions of a mixture of polymers. The value of the effect is determined by the donor-acceptor properties of the solvent and the degree of substitution of hydroxyl groups by acetate groups.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 8, pp. 1766–1768, August, 1989.     

Permeation of water as a tool for characterizing the effect of solvent, film thickness and water solubility in cellulose acetate membranes

Cellulose acetate membranes have been used in many applications; of particular interest are reverse osmosis systems, and as a neutral matrix for incorporation of different polymers (e.g., conducting polymers), inorganic ions (e.g., lanthanides) and organic (e.g., pharmaceutical) compounds. The properties of the new polymers derived from cellulose acetate or blends depend on those of cellulose acetate. This work presents an attempt to find links between thermodynamic and kinetic properties of cellulose acetate membranes in equilibrium with water. Water diffusion coefficients in cellulose acetate membranes are reported, measured with a simple water permeation technique. The comparison of these values with the percentage of water uptake and polymer thickness leads to interesting conclusions related with different polymer properties.     

Biodegradable Cellulose Graft Copolymers. I. Condensation-Type Graft Reactions

The synthesis of cellulose graft copolymers using condensation reactions to graft onto the cellulose backbone is described. Cellulose acetate (D.S. 2.27) was grafted with MDI and TDI. The cellulose acetate-MDI copolymer was further reacted with hydroxy-terminated poly(butadiene-styrene) copolymer and polyethylene glycol. Grafting was confirmed by Pmr and IR spectroscopy. The copolymers were easily deacetylated with NaOMe. The deacetylated products were readily degraded by cellulysin, faster than cellulose itself.     

Preparation and Characterization of Chitosan Composite Membranes Crosslinked by Carboxyl-capped Poly（ethylene glycol）

In this study a series of chemically crosslinked chitosan/poly（ethylene glycol） （CS/PEG） composite membranes were prepared with PEG as a crosslinking reagent other than an additional blend. First, carboxyl-eapped poly（ethylene glycol） （HOOC-PEG-COOH） was synthesized. Dense CS/PEG composite membranes were then prepared by casting/evaporation of CS and HOOC-PEG-COOH mixture in acetic acid solution. Chitosan was chemically crosslinked due to the amidation between the carboxyl in HOOC-PEG-COOH and the amino in chitosan under heating, as confirmed by FTIR analysis. The hydrophilicity, water-resistance and mechanical properties of pure and crosslinked chitosan membranes were characterized, respectively. The results of water contact angle and water absorption showed that the hydrophilicity of chitosan membranes could be significantly improved, while no significant difference of weight loss between pure chitosan membranes and crosslinked ones was detected, indicating that composite membranes with amidation crosslinking possess excellent water resistanance ability. Moreover, the tensile strength of chitosan membranes could be significantly enhanced with the addition of certain amount of HOOC-PEG-COOH crosslinker, while the elongation at break didn＇t degrade at the same time. Additionally, the results of swelling behaviors in water at different pH suggested that the composite membranes were pH sensitive.     

柚皮苷分子印迹膜的水相制备与识别

以柚皮苷为印迹分子,PEG为致孔剂,在水相中制备了柚皮苷分子印迹壳聚糖膜.分别讨论了交联剂、致孔剂和印迹分子的用量对印迹膜结构和性能的影响.用SEM观察了致孔剂对印迹膜形貌及孔径的影响.紫外吸收光谱分析、柚皮苷在不同体系中的溶解度变化,以及红外光谱分析的结果表明功能聚合物壳聚糖和模板分子柚皮苷间形成了氢键.膜的渗透实验结果表明,在水相中,柚皮苷分子印迹膜能有效地从新橙皮苷和柚皮苷的混合液中分离出印迹分子柚皮苷,选择透过率为11.16%.     

Synthesis, characterization and thermal studies on cellulose acetate membranes with additive

Cellulose acetate (CA) membranes are used in ultrafiltration applications, although they show low chemical, mechanical and thermal resistance. In order to prepare membranes with improved properties, modification of cellulose acetate with polyethelene glycol (PEG 600) has been attempted. In this study, CA has been mixed with PEG 600 as an additive in a polar solvent. The effects of CA composition and additive concentration given by a mixture design of experiments on membrane compaction, pure water flux, water content and membrane hydraulic resistance have been studied and discussed. The efficiency of protein separation by the developed CA membranes have been quantified using model proteins such as pepsin, egg albumin (EA) and bovine serum albumin (BSA). The thermal stability of the developed membranes prepared with PEG 600 additive has also been investigated using thermogravimetric analysis and differential scanning calorimetry.     

Sensitive and selective detection of silver(I) ion in aqueous solution using carbon nanoparticles as a cheap, effective fluorescent sensing platform

In this Letter, we demonstrate the first use of carbon nanoparticles (CNPs) obtained from carbon soot by lighting a candle as a cheap, effective fluorescent sensing platform for Ag(+) detection with a detection limit as low as 500 pM and high selectivity. We further demonstrate its practical application to detect Ag(+) in a real sample.     

Removal of aromatic compounds in the aqueous solution via micellar enhanced ultrafiltration: Part 1. Behavior of nonionic surfactants

The effects of nonionic surfactants having different hydrophilicity and membranes having different hydrophobicity and molecular weight cut-off on the performance of micellar-enhanced ultrafiltration (MEUF) process were examined. A homologous series of polyethyleneglycol (PEG) alkylether having different numbers of methylene groups and ethylene oxide groups was used for nonionic surfactants. Polysulfone membranes and cellulose acetate membranes having different molecular cut-off were used for hydrophobic membranes and hydrophilic membranes, respectively. The concentration of surfactant added to pure water was fixed at the value of 100 times of critical micelle concentration (CMC). The flux through polysulfone membranes decreased remarkably due to adsorption mainly caused by hydrophobic interactions between surfactant and membrane material. The decline of solution flux for cellulose acetate membranes was not as serious as that for polysulfone membranes because of hydrophilic properties of cellulose acetate membranes. The surfactant rejections for the cellulose acetate membranes increased with decreasing membrane pore size and with increasing the hydrophobicity of surfactant. On the other hand the surfactant rejections for polysulfone membranes showed totally different rejection trends with those for cellulose acetate membranes. The surfactant rejections for the polysulfone membranes depend on the strength of hydrophobic interactions between surfactant and membrane material and molecular weight of surfactants.     

Cellulose acetate and polyetherimide blend ultrafiltration membranes: II. Effect of additive

Ultrafiltration membranes are largely applied in the separation of heavy metal ion and macromolecular solutes from aqueous streams. Studies are presented on ultrafiltration blend membranes, based on cellulose acetate (CA) and polyetherimide (PEI) in various blend compositions. Polyethylene glycol (PEG 600) was employed as a non‐solvent additive in various concentrations to the casting solution to improve the ultrafiltration performance of the resulting membranes. The blend membranes prepared were characterized in terms of compaction time, pure water flux (PWF), water content, membrane resistance, and scanning electron microscopy (SEM). The molecular weight cut‐off (MWCO) obtained from the protein separation studies is also reported. Applications of these membranes for separating toxic metal ions from aqueous streams are discussed. Copyright © 2007 John Wiley & Sons, Ltd.     

Effect of preparation variables on morphology and pure water permeation flux through asymmetric cellulose acetate membranes

In this study, cellulose acetate (CA) ultrafiltration (UF) membranes were prepared using the phase inversion method. Effects of CA and polyethylene glycol (PEG) concentrations in the casting solution and coagulation bath temperature (CBT) on morphology of the synthesized membranes were investigated. Based on L₉ orthogonal array of Taguchi experimental design 18 membranes were synthesized (with two replications) and pure water permeation flux through them were measured. It was found out that increasing PEG concentration in the casting solution and CBT, accelerate diffusional exchange rate of solvent 1-methyl-2-pyrrolidone (NMP) and nonsolvent (water) and consequently facilitate formation of macrovoids in the membrane structure. Increasing CA concentration, however, slows down the demixing process. This prevents instantaneous growth of nucleuses in the membrane structure. Hence, a large number of small nucleuses are created and distributed throughout the polymer film and denser membranes are synthesized. Rate of water flux through the synthesized membranes is directly dependent on the size and number of macrovoids in the membrane structure. Thus, maximum value of flux is obtained at the highest levels of PEG concentration and CBT (10 wt.% and 23 °C, respectively) and the lowest level of CA concentration (13.5 wt.%). Analysis of variance (ANOVA) showed that all parameters have significant effects on the response. However, CBT is the less influential factor than CA and PEG concentrations on the response (flux).     

Porous membranes modified by hyperbranched polymers: I. Preparation and characterization of PVDF membrane using hyperbranched polyglycerol as additive

Porous membranes were prepared via phase inversion process from casting solution composed of poly(vinylidene fluoride) (PVDF), N,N-dimethylacetamide (DMAc), and hyperbranched polyglycerol (HPG). The membranes were characterized in terms of surface and bulk chemical compositions, morphology, water contact angle, porosity, and water flux. The effects of HPG content on membrane structures and properties were investigated. The effect of HPG addition on the hydrophilicity was discussed as well when the compositions of coagulation bath were changed. To better understand the special effects of HPG on the structures and properties of the membranes, PVDF membranes prepared using HPG as the additive were compared with those prepared using polyethylene glycol (PEG) as the additive.     

Application of cellulose acetate butyrate-based membrane for osmotic drug delivery

The release rate of drugs from an OROS^® is controlled by semipermeable membranes composed typically of cellulose acetate (CA) with various flux enhancers. Cellulose acetate butyrate (CAB) was identified as a viable alternative. The CAB membrane matched the CA membrane in robustness but had superior drying properties, offering particular advantages for thermolabile formulations. Studies were conducted to characterize CAB membrane properties with respect to performance of OROS^® systems. Four different membrane formulations with varying plasticizer type and concentration were investigated. The CAB based membranes exhibited superior drying characteristics and similar functionality to the CA:polyethylene glycol (PEG) membranes used as a control. A linear relationship was observed between the level of flux enhancer and release rate. The stability of the membrane was evaluated based on release profiles after system storage at various conditions. The CAB membranes appeared to have stability comparable to the standard CA membrane. A linear relationship between membrane weight and release rate as well as the time required to release 90% of a drug from the system [T₉₀] for a model formulation was observed. In conclusion, the newly identified alternative membrane composition allows for the use of thinner membranes, thereby reducing cost of goods, coating time and, most importantly, membrane drying time.     

Phase inversion cellulose acetate membranes for suppression of protein interferences in anodic stripping voltammetry 2(1). Improvement of the membrane preparation procedure

Phase inversion (PI) cellulose acetate membranes were cast on glassy carbon electrodes from a solution containing acetone as solvent and aqueous magnesium perchlorate as pore former. It is shown that a significant improvement of the reproducibility and permselective properties of the membrane is obtained by allowing complete evaporation of the solvent in a controlled humidity environment before the membrane is gelated. By using cadmium and lead as test analytes and differential pulse anodic stripping voltammetry as the detection method, it was found that the modification of the electrode greatly reduces the interference from albumin, lysozyme, gelatin and polyethylene glycol (MW 6000). The permselectivity of the PI membrane can be controlled by varying the amount of magnesium perchlorate in the casting solution and the relative humidity during the pre-gelation conditioning of the membrane.     

Pervaporation dehydration of ethanol–water mixtures with chitosan/hydroxyethylcellulose (CS/HEC) composite membranes: I. Effect of operating conditions

Composite hydrophilic pervaporation membranes were prepared from chitosan blended with hydroxyethylcellulose using cellulose acetate as a porous support. The membranes were tested for dehydration performance of ethanol–water mixtures of ethanol concentrations 70–95 wt.% in the laminar flow region, at temperatures 50–70°C and at permeate pressures of 3–30 mmHg. The composite membrane showed an improved dehydration performance compared with dense CS/HEC membrane developed earlier. The effects of operating conditions also revealed that pervaporation of low water content feed carried out at high feed flow rate and at low temperature and permeate pressure was an advantage.     

二醋酸纤维素 -聚乙二醇接枝共聚物的核磁共振表征

用^1H NMR和^13C NMR核磁共振技术研究了二醋酸纤维素和聚乙二醇的接枝反应,并确定了^1H NMR和^13C NMR谱中各谱峰的归属,为证明二醋酸纤维素和聚乙二醇的接枝反应提供了依据。     

Exploring the characteristics,performance, and modification of Matrimid for development of thin‐film composite and thin‐film nanocomposite reverse osmosis membranes

Reverse osmosis (RO) membrane technology is widely employed to address the demands for freshwater. In this study, fabrication and performance evaluation of customized RO membranes comprised of Matrimid and polyacrylonitrile (PAN) is carried out. While exploring adoption of slip coating procedure, the effects of various modification techniques including incorporation of TiO₂ nanoparticles and polyethylene glycol (PEG) into the skin layer as well as cross‐linking were investigated. The individual and combined effects of parameters on membrane morphology, surface characteristics and performance were also examined. Despite the distinctive characteristics of involved materials, delamination‐free composite membranes were successfully formed with an intimate contact at the interface of two layers. The results also indicated that increasing concentration of Matrimid in dope solution led to increase in membrane thickness and consequently decline in water flux. In the best case, membrane prepared using 1 wt.% Matrimid in dope exhibited water flux of 0.98 LMH and NaCl rejection of 95.7%. Also, incorporation of 3 wt.% TiO₂ nanoparticles offered membranes with improved water flux of 1.37 LMH and salt rejection of 95.8%. On the other hand, water flux and salt rejection in membranes containing 5 wt.% PEG were 1.18 LMH and 96.2%, respectively. The co‐presence of both nanoparticles and PEG provided more insights about the contributing factors in tuned membranes. Modification of skin layer by cross‐linking significantly improved salt rejection at the expense of water flux. The results are scientifically interpreted and compared to the values reported in literature.