Effect of the solvent on growth and properties of polyaniline-based composite films

In this study, we report on the electrosyntheses of polyaniline (PAni) and PAni/magnetite nanoparticle (PAni/Fe₃O₄-NP) composite films by a potentiodynamic method from water and ethanol solutions. The aim of the study is to evaluate the effect of the solvent on the electrochemical growth of these films. The growth cyclic voltammograms and the mass change variation (Δm), determined by the electrochemical quartz crystal microbalance technique, show that the polymer growth rate is lower in ethanol than in water (Δm in water is ca. 50% higher than in ethanol after 30 voltammetric cycles). As a consequence, the films grown from ethanol show a more compact and uniform morphology, as we observed with scanning electron microscopy. Furthermore, the formation of oxidation products is inhibited in ethanol. The PAni/Fe₃O₄-NP composite films electrosynthesized in ethanol showed enhanced electrochemical response than the composite films grown from water. This is attributed to the better dispersion of the nanoparticles in this solvent and consequently in the polymer matrix, as confirmed by the Δm value and the spectroscopic characterization. We conclude that electropolymerization from ethanol solution provides high-quality PAni and PAni/Fe₃O₄-NP composite films; the electrochemical and morphological properties of these films suggest that their use for corrosion protection is promising.     

Preparation of antibacterial polyimide films containing silver nanoparticles

Polyimide/silver composite films were successfully prepared by in situ polymerization. A precursor, AgNO₃ was used as the source of the silver nanoparticles. The structure and morphology of resulting films were characterized by FTIR spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM). Consequently, the silver nanoparticles were well dispersed in polyimide matrix. Meanwhile, thermal properties from thermal gravimetric analyses (TGA) and mechanical properties from tensile test which confirmed composites were kept good performance as compared to pure polyimide. In addition, the antimicrobial activity of polyimide/silver composite films against three different bacteria, B. subtilis, S. aureus, and E. coil, illustrated excellent activity. This composite is potential useful as antimicrobial material with good thermal performance in a wide variety of biomedical and general use applications.     

Gelatin/montmorillonite biohybrid films prepared via a novel photocrosslinking method: structure–properties investigations

Gelatin/sodium montmorillonite (Na⁺MMT) hybrid nanocomposite films were prepared by a new photocrosslinking method using 4-(2-hydroxyethoxy)phenyl-(2-hydroxy-2-propyl)ketone (Irgacure 2959) as a photoactive radical initiator and N,N′-Methylenebisacrylamide (MBA) as a crosslinking agent. The prepared samples were characterized by X-ray diffraction (XRD), differential scanning calorimetry, stress–strain measurements and UV–Vis spectrophotometry. XRD patterns showed the formation of exfoliation structure resulting in considerable improves in mechanical properties of the nanocomposite. Retaining of transparency also suggested that Na⁺MMT nanosheets were uniformly distributed in the gelatin matrix. The tensile strength and Elastic’s modulus of nanocomposites were also improved notably by enhancing amount of Na⁺MMT. Furthermore, gelatin/Na⁺MMT nanocomposites showed a second T _g at a higher temperature in presence of Na⁺MMT.     

Thermal behavior of flax and jute reinforced in matrix acrylic composite

Natural fabric such as flax and jute was considered in biaxial plain reinforcement in matrix of acrylic resin, and the composite is prepared in hand layup techniques. Fabric mass fraction of 7% was used in the matrix of composite. The samples were treated at r.t and 60 °C for the final fabrication. Scanning electron microscopy was carried out to support the microstructure effect of composite in terms of thermal change. Thermogravimetric and differential thermogravimetric analysis and residual compositional analysis with FTIR were carried out for the composite and matrix samples. The mechanical and viscoelastic properties, as well as the influence of frequency and fibers types, were evaluated, in flexural mode, by means of dynamical mechanical analysis. Glass transition (T _g) and initial decomposition (T _i) temperatures increase with incorporation of fibers into the matrix. While T _i of flax and jute composite was similar, T _g in case of flax improves than jute fabric-reinforced composite. This type of composites can be used in the automotive sector, in exterior and exterior components.     

Slow Down Dewetting in Polymer Films by Isocyanate-treated Graphite Oxide

Isocyanate-treated graphite oxides(i GOs) were well-dispersed into the polystyrene(PS) thin films and formed a novel network structure. With control in fabrication, an i GOs-web layer was horizontally embedded near the surface of the films and thus formed a composite slightly doped by i GOs. This work demonstrated that the i GOs network can remarkably depress the dewetting process in the polymer matrix of the composite, while dewetting often leads to rupture of polymer films and is considered as a major practical limit in using polymeric materials above their glass transition temperatures(Tg). Via annealing the 50–120 nm thick composite and associated neat PS films at temperatures ranging from 35 °C to 70 °C above Tg, surface morphology evolution of the films was monitored by atomic force microscopy(AFM). The i GOs-doped PS exhibited excellent thermal stability, i.e., the number of dewetting holes was greatly reduced and the long-term hole growth was fairly restricted. In contrast, the neat PS film showed serious surface fluctuation and a final rupture induced by ordinary dewetting. The method developed in this work may pave a road to reinforce thin polymer films and enhance their thermal stability, in order to meet requirements by technological advances.     

Simultaneously improving the tensile and impact properties of isotactic polypropylene with the cooperation of <Emphasis Type="Italic">co</Emphasis>-PP and <Emphasis Type="Italic">β</Emphasis>-nucleating agent through pressure vibration injection molding

In this article, crystalline morphology and molecular orientation of isotactic polypropylene (iPP), random copolymerized polypropylene (co-PP) and β-nucleating agent (β-NA) composites prepared by pressure vibration injection molding (PVIM) have been investigated via polarized light microscopy, scanning electron microscopy, wide-angle X-ray diffraction and differential scanning calorimetry. Results demonstrated that the interaction between co-PP and iPP molecular chains was beneficial for the mechanical improvement and the introduction of β-NA further improved the toughness of iPP. In addition, after applying the pressure vibration injection molding (PVIM) technology, the shear layer thickness increased remarkably and the tensile strength improved consequently. Thus, the strength and toughness of iPP/co-PP/β-NA composites prepared by PVIM were simultaneously improved compared to those of the pure iPP prepared by conventional injection molding (CIM): the impact toughness was increased by five times and tensile strength was increased by 9 MPa. This work provided a new method to further enhance the properties of iPP/co-PP composites through dynamic processing strategy.     

Mechanochemical synthesis of colloidal silver bromide particles in the NaBr–AgNO<Subscript>3</Subscript>–NaNO<Subscript>3</Subscript> system

X-ray diffraction and thermal analyses, electron microscopy, and dynamic light scattering have been employed to study silver bromide nanoparticles obtained by the mechanochemical exchange reaction NaBr + AgNO₃ + zNaNO₃ = (z + 1)NaNO₃ + AgBr in sodium nitrate matrix (diluent and side reaction product) at z = z₁ = 8.06 and z = z₂ = 4.31. AgBr nanoparticles have been obtained in the free form by dissolving the matrix in water, and their activity in the photodegradation of methylene blue dye has been studied.     

Parenchyma cell wall structure in twining stem of <Emphasis Type="Italic">Dioscorea balcanica</Emphasis>

Anatomical adaptation of liana plants includes structural changes in cell walls of different tissues: fibers, vessel elements and tracheids. However, the contribution of parenchyma cells to stem twining in liana plants is mostly unknown. The aim of this investigation is to determine changes in stem parenchyma cell walls that are correlated with the twinning process in liana plants. Parenchyma cell wall structure was studied on the stem cross sections of straight and twisted internodes of monocotyledonous liana Dioscorea balcanica, by different microscopy techniques: light microscopy, scanning electron microscopy, fluorescence detected linear dichroism microscopy and Fourier transform infrared microspectrometry. In addition, chemical analysis of the entire stem internodes was performed using photometric and chromatographic methods. Parenchyma cell walls of twisted D. balcanica internodes are characterized by: lower amounts of cellulose (obtained by FTIR microspectrometry) with different cellulose microfibril orientation (shown by Scanning electron microscopy), but no changes in “cellulose fibril order” (obtained by Differential polarization laser scanning microscopy); lower amounts of xyloglucan, higher amounts of xylan, higher amounts of lignin with modified organization—less condensed lignin (obtained by FTIR microspectrometry). At the same time, chemical analysis of the entire internodes did not show significant differences in lignin content and cell wall bound phenols related to stem twining, except for the presence of diferulate cross-links exclusively in twisted internodes. Our results indicate that adaptations to mechanical strain in D. balcanica stems involve modifications in parenchyma cell wall structure and chemistry, which provide decreased stiffness, higher strength and increased elasticity of twisted internodes.     

Preparation of starch-<Emphasis Type="Italic">g</Emphasis>-PMMA,starch-<Emphasis Type="Italic">g</Emphasis>-P(MMA/BMA) and starch-<Emphasis Type="Italic">g</Emphasis>-P(MMA/MA) nanoparticles and their reinforcing effect on natural rubber by latex blending: a comparative study

Nanoparticles including starch-graft-methylmethacrylate, starch-graft-(methylmethacrylate/methyl acrylate), starch-graft-(methyl methacrylate/butyl methacrylate) were synthesized via emulsifier-free emulsion polymerization and were blended with natural rubber latex at various mass ratios. Chemical structure of graft copolymers was confirmed by Fourier transform infrared. Transmission electron microscopy demonstrated the core-shell structures of the nanoparticles distributed uniformly around the natural rubble particles. The tensile strength of blend films was significantly enhanced by addition of graft copolymers. Besides, scanning electron microscopy and atomic force microscopy showed the blend film had smooth surface.     

Facile synthesis of TiO<Subscript>2</Subscript>/Ag composite aerogel with excellent antibacterial properties

In this study, the effective TiO₂/Ag composite antibacterial aerogel powder is prepared by facile sol–gel method and ethanol supercritical technology. The surface morphology, structural properties, and chemical components are monitored by scanning electron microscopy (SEM), transmission electron microscope (TEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR), and energy disperse?spectroscopy (EDS). Meanwhile, absorbance spectra and specific surface area of TiO₂/Ag composite aerogel are characterized by UV-Vis spectra and Brunauer–Emmett–Teller. The TiO₂/Ag composite aerogel with Ti/Ag molar ratios of 10:1, 30:1, 50:1 are measured for its antibacterial property by using Escherichia coliform (E.coli) and Staphylococcus aureus (S. aureus). The results show that the size of TiO₂ and Ag nanoparticles are 40?nm and 25?nm, respectively. Simultaneously, the obtained composite aerogel with a porous structure possessed a surface area of 148?m²/g, an average pore size 11.5?nm, and a pore volume 0.39?cm³/g. With the increase of Ag content, the antibacterial properties of composite aerogel are greatly improved compared with pure TiO₂ aerogel. When Ag/Ti molar ratios was 1:10, the highest antibacterial rate can up to 99%, and the inhibition bands of E. coli and S. aureus are 23?mm and 19?mm, respectively.

Open image in new window

Schematic representation of growth mechanism of TiO₂/Ag composite aerogel (a) and antibacterial performance test (b, c)

     

Structure and properties of regenerated cellulose/tourmaline nanocrystal composite films

Nanocomposite films were successfully prepared from cellulose and tourmaline nanocrystals with mean diameters of 70 nm in a 1.5 M NaOH/0.65 M thiourea aqueous solution by coagulation with 5 wt % CaCl₂ and then a 3 wt % HCl aqueous solution for 2 min. The structure and properties of the composite films were characterized by X‐ray diffraction, scanning electron microscopy, transmission electron microscopy, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and tensile testing. The results indicated that the tourmaline nanocrystals were dispersed in a cellulose matrix, maintaining the original structure of the nanocrystals in the composite films. The loss peaks (tan δ) in the DMA spectra and the decomposition temperatures in the DSC curves of the composite films were significantly shifted toward low temperatures, suggesting that the nanocrystals broke the partial intermolecular hydrogen bonds of cellulose, and this led to a reduction in the thermal stability. However, the nanocomposite films exhibited a homogeneous structure and dispersion of the nanocrystals. When the tourmaline content was in the range of 4–8 wt %, the composite films possessed good tensile strength (92–107 MPa) and exhibited obvious antibacterial action against Staphylococcus aureus. This work provides a potential way of preparing functional composite films or fibers from cellulose and nanoinorganic particles with NaOH/thiourea aqueous solutions. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 367–373, 2004     

Dual-functional chitosan–methylisothiazolinone/microfibrillated cellulose biocomposites for enhancing antibacterial and mechanical properties of agar films

In order to enhance the antibacterial and mechanical properties of agar films, the chitosan-methylisothiazolinone (C–MIT) complex was first prepared by the ionic gelation method, and the characterization of the C–MIT complex was carried out by Fourier transform infrared spectroscopy, transmission electron microscopy, and Thermo gravimetry. Chitosan was successfully crosslinked with tripolyphosphate for the nanoencapsulation of methylisothiazolinone, and the C–MIT complex was spherical in shape with a diameter of about 10 nm. The C–MIT/MFC biocomposites obtained through the adsorption of the C–MIT complex on the microfibrillated cellulose (MFC) was then incorporated into the agar films. In comparison with the pure agar films, the tensile strength of the agar composite films was increased by about 19 % at the loading of 10 wt% of C–MIT/MFC biocomposites, and antibacterial tests demonstrated that the agar composite films exhibited remarkable antibacterial activities against both Escherichia coli and Staphylococcus aureus. This work provides a new approach to utilizing multifunctional agar films in the medical field.     

Preparation,characterization and antimicrobial application of hybrid cellulose-lignin beads

In the present study, cellulose-lignin beads were prepared using pretreated dissolving grade-pulp and extracted from birch wood hydrotropic lignin as starting materials. The preparation involved dissolution of both polymers in environmentally friendly 7% NaOH/12% urea aqueous solution, shaping the solution into beads and subsequent regeneration. Lignin content in the beads varied from 0 to 40%. The beads were characterized using FTIR, scanning electron and confocal fluorescence microscopy. Porosity, swelling behavior and leaching of lignin from the beads in water were studied as well. The antibacterial properties of the beads and original hydrotropic lignin were tested using Escherichia coli (XL-1 Blue) and Staphylococcus aureus (ATCC 25923). The obtained beads in a never-dried state were highly porous spherical particles with evenly distributed lignin in them. Their shape, structure and properties were influenced by the lignin content. The beads did not show antibacterial activity against gram-negative E. coli. On the other hand, never-dried cellulose-lignin beads inhibited growth of gram-positive S. aureus, and the inhibition efficiency increased with the lignin content. The half inhibitory concentration for never-dried beads with 40% of lignin was 1.06 mg (dry weight) per 1 mL of broth determined after incubation for 24 h at 37 °C and at initial concentration of S. aureus of 6.48 log(CFU/mL). In contrast to cellulose-lignin beads, pure cellulose beads did not inhibit growth of S aureus. The results demonstrated that hydrotropic birch lignin can be used for the preparation of composite cellulose-lignin beads. Such beads show a great potential for antibacterial applications against S. aureus.     

Studying structural,morphological and optical properties of nanocrystalline ZnO:Ag films prepared by sol–gel method for antimicrobial activity

Pure and Ag-doped zinc oxide sol–gel thin films were prepared by spin-coating process. Pure and Ag–ZnO films, containing 2–8% Ag, were annealed at 500?°C for 2?h. All thin films were prepared and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and UV–visible spectroscopy. X-ray diffraction studies show the polycrystalline nature with hexagonal wurtzite structure of ZnO and Ag:ZnO thin films. The crystallite size of the prepared samples reduced with increasing Ag doping concentrations. AFM and SEM results indicated that the average crystallite size decreased as Ag doping concentration increased. The transmittance spectra were then recorded at wavelengths ranging from 300 to 1000?nm. The films produced yielded high transmission at visible regions. The optical band gap energy of spin-coated films also decreased as Ag doping concentration increased. In particular, their optical band gap energies were 3.75, 3.55, 3.4, 3.3, and 3.23?eV at 0%, 2%, 4%, 6%, and 8%, respectively. Antibacterial activity of pure and Ag-doped zinc oxide against Escherichia coli and Staphylococcus aureus was evaluated by international recognized test (JIS Z 2801). The results showed that pure and Ag-doped ZnO thin film has an antibacterial inhibition zone against E. coli and S. aureus. Gram-positive bacteria seemed to be more resistant to pure and Ag-doped ZnO thin film than gram-negative bacteria. The test shows incrementally increasing in antibacterial activity of the thin films when dopant ratio increased under UV light.

Open image in new window

     

Synthesis of novel coumarin substituted amide derivatives and their antibacterial activities

A series of novel coumarin substituted amide derivatives were synthesized and evaluated for their antibacterial activities. Result indicated that compounds 3f, 3g, 3h, 3i, 3j, 3k, 3l, 3m, 3n, 3o and 3q exhibited excellent antibacterial activities against Xanthomonas oryzae pv. oryzae (Xoo) and Xanthomonas citri subsp. Citri (Xcc) in vitro, which were better than those of commercial agricultural antibacterial thiodiazole-copper. The title compounds with electron-withdrawing group showed better antibacterial activities than those of compounds with electron-donating group, and the title compounds bearing the same substituent group exhibited better antibacterial activities against Xcc than antibacterial activities against Xoo.     

Phase-equilibrium and cellulose-coagulation kinetics for cellulose solutions in <Emphasis Type="Italic">N</Emphasis>-methylmorpholine-<Emphasis Type="Italic">N</Emphasis>-oxide

The dissolution of cellulose in N-methylmorpholine-N-oxide monohydrate and the dissolution of N-methylmorpholine-N-oxide monohydrate in water have been studied via optical interferometry. A part of the phase diagram for the cellulose/N-methylmorpholine-N-oxide system has been constructed. The phase diagram is characterized by crystalline equilibrium, hysteresis of the melting temperatures of the solvents, and a region of anisotropy. Optical interferometry has been used for the first time to study the kinetics of cellulose coagulation during the interaction of cellulose solutions in N-methylmorpholine-N-oxide with water and water solutions of N-methylmorpholine-N-oxide. Information on the values of interdiffusion coefficients and the morphologies of the resulting cellulose films has been obtained. The possibility to use optical interferometry to analyze the interaction of a solution with the coagulating agent in the case of cellulose fiber and film formation has been demonstrated. The influences of temperature, the nature of the coagulating agent, and the cellulose content on the kinetics of the process and morphologies of the formed films have been shown. The use of N-methylmorpholine-N-oxide as a part of the coagulation system decreases the rate of interdiffusion of solutions, thereby resulting in a more uniform and dense morphology of cellulose films. Increased temperature causes diffusion acceleration, thereby leading to the formation of an anisotropic morphology of the cellulose films.     

Improving the mechanical properties of CNF films by NMMO partial dissolution with hot calender activation

Reinforcing of cellulose nanofibril (CNF) films by partial dissolution with N-methylmorpholine-N-oxide (NMMO) was investigated. The method investigated is composed of impregnation of CNF film with liquid solution of NMMO followed by dry heat activation. The heat activation of the impregnated film was carried out using a heated calendering nip, which enabled simultaneous heating and compression. The partial dissolution of cellulose by NMMO caused a significant increase in the transparency of CNF film due to the decrease of film porosity and increased surface smoothness. The dry strength of the reinforced film was increased from 122 up to 195 MPa. Furthermore, the wet strength of the reinforced film was up to 70% greater than the dry strength of pure CNF film. The changes in the fibrillar structure were investigated with topographical imaging (SEM and AFM) and spectroscopically using NMR and FTIR. No significant changes in the fibril structure or cellulose morphology were observed. Moreover, the treated film resisted significant water pressure, highlighting CNF film’s permanent water resistance. The partial dissolution process with NMMO was also capable of reinforcing a CNF composite film with macro scale structural elements (lyocell short-cut fibres). The strategy investigated is a robust and fast method to improve the mechanical properties of fibrillary cellulose films, allowing them utilization in applications where improved water resistance and fully cellulosic character are required properties.     

Structure characterization of cellulose nanofiber hydrogel as functions of concentration and ionic strength

Carboxylated cellulose nanofibers (CNFs), having an average width of 7 nm and thickness of 1.5 nm, were produced by TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl radical)-mediated oxidation method. The fiber cross-sectional dimensions were determined using small-angle X-ray scattering (SAXS), transmission electron microscopy and atomic force microscopy techniques, where the rheological properties under different concentration and ionic strength were also investigated. The formation of hydrogel was evidenced by increasing the CNF concentration or ionic strength of the solvent (water), while the gel structure in ion-induced CNF hydrogels was found to be relatively inhomogeneous. The gelation behavior was closely related to the segmental aggregation of charged CNF, which could be quantitatively characterized by the correlation length (ξ) from the low-angle scattering profile and the scattering invariant (Q) in SAXS.     

Microwave-assisted <Emphasis Type="Italic">in situ</Emphasis> synthesis of fluorescent gold nanoclusters with BSA/montmorillonite and application on latent fingermark imaging

A method for in situ preparation of fluorescent gold nanoclusters (AuNCs) with bovine serum albumin/montmorillonite composite powder (AuNC-BSA/MMT) was developed, and the products were used to detect latent fingermarks. In this work, AuNCs were “grown” both inside and on the surface of BSA/MMT clay using one-step reduction of HAuCl4 by BSA. The as-prepared AuNC-BSA/MMT nanocomposites emit intensive red fluorescence under the excitation of UV-visible light and show stable chemical features and low toxicity. The obtained fluorescent powders were characterized by UV-visible absorption spectroscopy, fluorescence spectroscopy, infrared spectroscopy, transmission electron microscopy/high-resolution transmission electron microscopy, scanning electron microscopy, X-ray photoelectron spectroscopy and X-ray diffraction to depict their sizes, structural information and optical features. Given their environmentally friendly preparation, simple operation, low cost, efficient UVvisible radiation-dependent photoluminescence and good affinity with finger residues, the in situ synthesized AuNC-BSA/MMT nanocomposite powders were used as an alternative fluorescent developing reagent for developing latent fingermarks deposited on various object surfaces (such as glass, aluminum foil, painted metal, plastic products and weighing papers) for individual identification. As results, the developed fingermarks with clear patterns and satisfactory level-2 (minutiae points) and level-3 (sweat pores) ridge details were obtained. Notably, treated prints could be excited by red light and emitted near infrared fluorescence, which was beneficial to avoid background interference and reduce the damage caused by UV light. With the advantages of the simple preparation process and good enhancement performance for latent fingermarks, the proposed method might be used in the preparation of various fluorescent probes for detecting trace evidence in forensic sciences.