环氧乙烷胺化制乙醇胺

环氧乙烷选择性胺化制备乙醇胺成为近年来胺化反应的热点课题。乙醇胺主要由氨水法与液氨法两种制备方法合成,它们分属于典型的均相催化与多相催化。本文从热力学、动力学、反应机理等方面对氨水法的研究进展进行了系统地综述,并部分探讨了工业上氨水法的工艺条件。从催化剂的种类、表面酸碱性质以及孔径结构等方面对液氨法的新进展进行了系统地阐述,最后探讨了选择性胺化反应的未来研究方向。     

Hydrolyzabilities of Different Corn Stover Fractions After Aqueous Ammonia Pretreatment

The effect of aqueous ammonia pretreatment on the hydrolysis of different corn stover fractions (rind, husk, leaf, and pith) by xylanase (XYL) with cellulases (CELs) was evaluated. The aqueous ammonia pretreatment had excellent delignification ability (above 66 %) for different corn stover fractions. The corn rind exhibited the lowest susceptibility to aqueous ammonia pretreatment. The pretreated rind showed the lowest hydrolyzability by CEL and XYL, which was supported by a high content of crystalline cellulose in the hydrolyzed residues of rind, as confirmed by X-ray diffraction (XRD). With the addition of 1 mg XYL/g dry matter, a high glucose yield (above 90 %) could be obtained from the pretreated rind by CEL. The results revealed that a high hydrolyzate yield of corn rind after aqueous ammonia pretreatment could be obtained with 1 mg xylanase/g dry matter, showing that aqueous ammonia pretreatment and xylanase addition to cellulases have great potential for the efficient hydrolysis of corn stover without previous fractionation.     

Peroxide-Ammonia Delignification of Pine Wood

Oxidative delignification of pine wood by hydrogen peroxide in aqueous ammonia was studied. A new method for producing cellulose and N-containing organic fertilizers was developed. It was demonstrated that a solution of hydrogen peroxide (3-9%) in aqueous ammonia delignified extensively wood to produce cellulose in yields up to 54.6% with a residual lignin content up to 1.1%. The process of pine-wood delignification by hydrogen peroxide in aqueous ammonia was described satisfactorily by a first-order kinetic equation.     

Extraction of Mercaptans from Light Hydrocarbon Mixtures with Aqueous Ammonia

Results of laboratory studies of the extraction of light mercaptans (methyl, ethyl, and propyl mercaptans) from hydrocarbons mixtures with a 25% aqueous solution of ammonia (caustic ammonia) are presented and discussed. It is shown that aqueous ammonia can in principle be used for controlled demercaptanization of light hydrocarbon fractions and liquefied hydrocarbon gases containing hydrogen sulfide and lower mercaptans. The advantage of this demercaptanization method over the conventional processes of alkali treatment is that there is no stage of oxidative catalytic regeneration of a spent alkali and there are no its highly toxic wastes, sulfurousalkaline waste waters. The regeneration of a spent (saturated with sulfurous compounds) aqueous ammonia can be comparatively easily performed by its heating (boiling), which leads to a hydrolytic decomposition of ammonium sulfides and mercaptides to release their constituent gases: hydrogen sulfide, mercaptans, and ammonia. Ammonia is recycled into the process as freshly prepared (regenerated) caustic ammonia.

     

Homogeneous precipitation of mullite precursors

The synthesis of mullite powders or gels from an aqueous precursor solution has been studied. The starting solution is made by hydrolyzing TEOS into an aqueous solution of aluminium nitrate. When this solution is sprayed into a solution of ammonia in isopropanol, a nearly monophasic mullite precursor is obtained, whereas if this precipitation is made into an aqueous solution of ammonia, or ammonium carbonate, a diphasic colloidal precipitate is formed. By a slow and homogeneous precipitation in aqueous solution, induced by in-situ generation of ammonia by thermal hydrolysis of urea, a monophasic gel is also obtained. The samples have been studied by DTA, DSC, TGA, XRD and dilatometry.     

Pretreatment of wastepaper and pulp mill sludge by aqueous ammonia and hydrogen peroxide

Pretreatment of two different softwood-based lignocellulosic wastes (newsprint and Kraft pulp mill sludge) was investigated. Pretreatment was done by aqueous ammonia and hydrogen peroxide (H₂O₂), two delignifying reagents that are environmentally benign. Three different treatment schemes were employed: aqueous ammonia alone (ammonia recycled percolation [ARP]), mixed stream of aqueous ammonia and H₂O₂ and successive treatment with H₂O₂ and aqueous ammonia. In all cases there was a substantial degree of delignification ranging from 30 to 50%. About half of the hemicellulose sugars were dissolved into the process effluent. Retention of cellulose after pretreatment varied from 85 to 100% for newspaper feedstock and from 77 to 85% for the pulp mill sludge. After treatment with aqueous ammonia alone (ARP), the digestibility of newspaper and the pulp mill sludge was improved only by 5% (from 40 to 45% for the former and from 68 to 73% for the latter), despite a substantial degree of delignification occurring after the ARP process. The lign in content thus did not correlate with the digestibility for these substrates. Simultaneous treatment with H₂O₂ and aqueous ammonia did not bring about any significant improvement in the digestibility over that of the ARP. A succcessive treatment by H₂O₂ and ARP showed the most promise because it improved the digestibility of the newspaper from 41 to 75%, a level comparable to that of α-cellulose.     

Amino- and hydrodefluorination of polyfluoroaromatic amines with aqueous ammonia in a steel autoclave. Synthesis of highly pure tetrafluorophenylenediamines

The action of aqueous ammonia on hexafluorobenzene in a steel autoclave at 180—220 °C yields a mixture of isomeric tetrafluorophenylenediamines and 2,4,5-trifluorophenylene-1,3-diamine. The content of the hydrodefluorination product significantly depends on the reaction temperature and time. Tetrafluorophenylene-1,3-diamine undergoes hydrodefluorination with aqueous ammonia in a steel autoclave at 200 °C to give 2,4,5-trifluorophenylene-1,3-diamine; when the additives of NH₄F and/or FeCl₃ are present, 2,5-difluorophenylene-1,3-diamine is additionally formed. The hydrodefluorination products are not formed during bis-aminodefluorination of hexafluorobenzene with aqueous ammonia in a glass reactor or with anhydrous ammonia (in a mixture with aprotic solvent) in a steel autoclave.     

One-pot synthesis of N-aryl propargylamine from aromatic boronic acid,aqueous ammonia,and propargyl bromide under microwave-assisted conditions

A facile,one-pot synthesis of N-aryl propargylamine from aromatic boronic acid,aqueous ammonia,and propargyl bromide has been achieved under microwave-assisted conditions.The reactions can be smoothly completed within a total 10 min through a two-step procedure,including copper-catalyzed coupling of aromatic boronic acids with aqueous ammonia and following propargylation by propargyl bromide.     

Ready synthesis of free N-H 2-arylindoles via the copper-catalyzed amination of 2-bromo-arylacetylenes with aqueous ammonia and sequential intramolecular cyclization

A wide range of free N-H 2-arylindoles were synthesised via the copper(II)-catalyzed amination of 2-bromo-arylacetylenes with aqueous ammonia and sequential intramolecular cyclization. The convenience and atom economy of aqueous ammonia, and the low cost of the copper catalytic system make this protocol readily superior in practical application.     

Electrical conductivity of the ammonia-water system

The electrical conductivity (EC) of the ammonia-water system was studied in the concentration range 0.1–10 mol/L ammonia and the temperature range 15–60°C. The maximal EC of aqueous ammonia at a given temperature is proposed as the parameter for generalizing experimental results. The normalized EC was calculated as the ratio of the EC of aqueous ammonia of a given concentration to the maximal EC at a given temperature. Over the ranges of the concentrations and temperatures studied, all normalized ECs fall on one curve. The EC activation energy was analyzed as a function of ammonia concentration and temperature.     

LaF3薄片的液相合成和表征

Single-crystalline LaF3 flakes was synthesized through a facile solution-phase approach in aqueous ammonia and ethylenediamine. Applying the thermal treatment at 100 ℃ for 20 h, the LaF3 recrystallized, grew epitaxially and precipitated into flakes in aqueous ammonia or ethylenediamine. The formation of flakes could be attributed to the coordination effect of the solvent.     

The State of Copper Ions in Aqueous and Aqueous Ammonia Solutions of Copper Acetate

Stabilization of Cu²⁺ ions in aqueous and aqueous ammonia solutions of copper acetate was studied for a wide range of ammonia concentrations. The structure of copper acetate hydrate complexes was shown to markedly change upon dissolution in water. In aqueous solutions, copper is stabilized as strongly bound Cu²⁺ associates (dimers) in a distorted octahedral environment composed of water molecules and acetate groups oxygen atoms in equatorial positions with strong exchange interaction via acetate groups. In solutions of copper acetate in aqueous ammonia, the concentration of ammonia has a crucial effect on the ordering of Cu²⁺ ions in associates. At high ammonia concentration, disordered copper tetra-ammoniate associates with the \({d_{{x^2} - {y^2}}}\) ground state are formed, whereas at low ammonia concentration, bulky Cu²⁺ ion associate structures are generated, with the \({d_{{x^2} - {y^2}}}\) ground state, hydroxyl groups in the equatorial plane, and water molecules in the axial positions.     

Extraction of nickel in the presence of ammonia with β-diketones containing phenyl and alkyl groups

The extraction of nickel chelates with β-diketones containing either alkyl or phenyl groups was examined in the absence and in the presence of ammonia in the aqueous solution, in order to define the effect of substituents and the coordinating effect of ammonia on the extraction. In the extraction of nickel chelates in the presence of ammonia, the extracted species were identified to be [NiA₂(NH₃)₂] (A: β-diketone anion) and ammonia acts both as adduct-forming in the organic phase and as a masking reagent in the aqueous phase.     

Palladium-catalyzed aminocarbonylation of aryl iodides using aqueous ammonia

Aminocarbonylation of aromatic iodides using aqueous ammonia in toluene has been developed. Various primary aromatic amides have been efficiently synthesized in good to excellent yields in the presence of catalytic quantities of Pd(OAc)₂/CYTOP®292. The usage of aqueous ammonia avoids the handling of two gases in the reaction.     

Practical CuCl/DABCO/4-HO-TEMPO-catalyzed oxidative synthesis of nitriles from alcohols with air as oxidant

A mild and efficient copper-catalyzed aerobic oxidative synthesis of nitriles directly from alcohols and aqueous ammonia with air as the terminal oxidant was disclosed. A variety of nitriles are obtained in good to excellent yields.     

含丙烯酸的共聚乳液的碱增稠过程与流动行为

合成了一系列苯乙烯、丙烯酸丁酯和丙烯酸共聚乳液样品，对乳液的加氢滴定过程及其流变行为进行了讨论。结果表明，氨的加入使含羧基乳液的增稠效应随共聚物中羧基含量的增加和柔性链段的增多而增大；随着氨的加入量的递增，乳液的ｐＨ值和粘度多呈两次突变；乳液因聚合物组成和ｐＨ值不同而具有不同的流动特性。     

An aqueous ammonia sensor based on an inkjet-printed polyaniline nanoparticle-modified electrode

A sensor for the amperometric detection of aqueous ammonia was fabricated using the inkjet printing of dodecylbenzene sulfonate (DBSA)-doped polyaniline nanoparticles (nanoPANI) onto a screen-printed carbon paste electrode. The combination of the environmentally inert, aqueous nanoparticle dispersion with the inkjet printing technique allowed the rapid fabrication of sensors based on polyaniline that was not easily achievable in the past due to the lack of processability of bulk forms of the conducting polymer. The resulting modified electrode was characterised with respect to its operating pH and number of print layers and was found to perform optimally at near neutral pH with four nanoPANI inkjet-printed layers. The sensor was tested in a flow injection system for its response to aqueous ammonia using amperometric detection at -0.3 V vs. Ag/AgCl pseudo-reference and was found to have reproducibility to injections of ammonia of below 5% RSD and good sensitivity with an experimental detection limit of 20 microM and a theoretical detection limit of 3.17 microM (0.54 ppm). The sensor was also tested for its day-to-day stability and its response towards a range of interferents common to refrigerant waste waters. This system allows the rapid production of an ultra-low-cost, solid state, polyaniline-based aqueous ammonia sensor.     

Copper-Catalyzed Amination of Aryl Halides with Aqueous Ammonia under Mild Conditions

A Cu(I) generated in situ from CuSO₄·5H₂O/sodium ascorbate catalyzed cross‐coupling reaction of aryl halides with aqueous ammonia for the synthesis of primary aromatic amines has been developed. Key to the success included the application of aqueous ammonia under a homogeneous condition.     

Tandem synthesis of aromatic amides from styrenes in water

An expedient one-pot synthesis of aromatic amides has been reported from styrenes in the presence of N-bromosuccinimide and iodine by using aqueous ammonia in water. The reaction proceeds through the formation of α-bromoketone as an intermediate in the presence of NBS and water. α-Bromoketone on reaction with iodine forms bromodiiodoketone which on nucleophilic substitution with aqueous ammonia gives aromatic amide. Substituted aromatic amides were obtained in good yields with wide functional group compatibility.     

Synthesis of 3-amino-4-nitropyrazoles

3-Bromo-1,5-dimethyl-4-nitropyrazole does not react upon heating with aqueous ammonia, while 1,5-dimethyl-3,4-dinitropyrazole under the same conditions yields 3-amino-1,5-dimethyl-4-nitropyrazole, which is formed from 3-bromo-1,5-dimethyl-4-nitropyrazole in the presence of a copper catalyst. The amination of 1-methyl-3,4-dinitropyrazole-5-carboxylic acid is accompanied by decarboxylation, which is characteristic for 4-substituted 1-methylpyrazole-5-carboxylic acids upon heating in aqueous ammonia or water.