辐射加热金X光再发射时间测量

利用星光Ⅱ三倍频激光打双盘靶，研究了辐射加热材料的Ｘ光发射时间。激光脉冲能量４０～６０Ｊ、脉冲宽度６００～７００ｐｓ。通过两台时间关联的亚千Ｘ光能谱仪分别监测双盘靶初、次级发射Ｘ光谱，给出了辐射加热次级Ｘ光再发射时间。     

激光腔靶辐射时间特性研究

介绍了激光加热腔靶辐射时间特性研究。实验采用滤长为１．０５３μｍ，能量为３０－７５０Ｊ，脉宽为６００－１１００ｐｓ的高斯型激光脉冲，辐照柱型腔靶，用两台具有一定和时间分辨的亚千Ｘ射线能谱仪，分别观察激光入射口和Ｘ光输运口的辐射时间特性，实验结果给出了腔靶源区发射Ｘ光时间过程及其与发射口面积，形状，发射能区等的关系。     

辐射加热不同材料靶的X光再发射研究

该课题研究辐射加热不同材料再发射Ｘ光特性。实验利用星光Ⅱ三倍频激光，以１×１０１４Ｗ／ｃｍ２激光强度辐照金盘形成辐射加热源，加热不同材料，利用多种诊断设备组合，并采取时、空、谱关联测量，给出辐射加热不同材料的再发射时间延迟，再发射效率，再发射光谱结构以及滞后等离子体碰撞发射的时、空特性。     

X射线胶片的脉冲光源响应标定

用ＬＦ－１１激光装置的１．０６μｍ脉冲激光加热Ｃｕ靶产生的Ｌ－壳层线辐射作脉冲Ｘ射线源，在曝光量为（０．０１～１０）－７Ｊ·ｃｍ－２范围内，标定了ＫＯＤＡＫＡＡ－５，ＫＯＤＡＫＳＷＲ和ＵＦＳＨ－Ｏ软Ｘ射线胶片的响应曲线，并与用连续光源标定的进行了对比．结果表明，这三种ｘ射线胶片，在强脉冲光源曝光条件下，都存在着胶片响应互易律失效问题，过去用连续光源标定的响应曲线，在激光等离子体诊断实验中，已经不能采用．     

激光等离子体X光辐射非平衡特性实验研究

在ＬＦ－１１和ＬＦ－１２高功率激光装置上进行的实验中，设计了一些特定的激光束－金腔靶－探测器条件，创造了激光直接加热、准辐射加热和激光、Ｘ光混合加热三种物理条件，采用软Ｘ光透射光栅能谱时空分辨技术，测量了腔靶、缝靶和双孔靶等高分辨Ｘ光能谱，研究了激光等离子体Ｘ光辐射非平衡特性。     

利用金刚石探测器测量软X光辐射功率

使用天然Ⅱａ型金刚石光电导探测器（ＰＣＤ），测量激光等离子体发射的软Ｘ光辐射。由于探测器在２００ｅＶ～２２００ｅＶ之间具有平响应特性，可以不加滤片直接测量Ｘ光功率和能量。金刚石ＰＣＤ与软Ｘ光能谱仪和平响应Ｘ光二级管的测量结果基本一致。     

利用快响应金刚石（Ⅱa型）光导探测器测量X射线

文中介绍了金刚石光导探测器的工作原理呼简化模型以及这种探测器所具有的独特的优点，并在激光－金（Ａｕ）平面靶实验中用来测量Ｘ射线，根据文献中灵敏度标定值给出激发辐照Ａｕ平面靶Ｘ光转换率为２７％左右，与目前公认的结果相一致。     

高偏压金属─绝缘体─金属结的光发射

我们制作了一种可在６—１１Ｖ偏压范围内均匀发射可见光的新型金属—绝缘体—金属结型发光器件，其内层结构是Ａｌ－Ａｌ２Ｏ３－ＭｇＦ２－Ａｎ（Ｃｕ），其承受偏压、单位面积发光功率及相应的外量子效应高过迄今已知的Ｍ－Ｏ－Ｍ遂道结型发光器件．本文首次报导并论证了这一由Ｓｃｈｏｔｔｋｙ热电子所激发的光发射及其物理图象：Ｓｃｈｏｔｔｋｙ热电子在ＡＯ（Ｃｕ）－真空界面激发表面等离极化激元（ＳＰＰ）；Ａｕ（Ｃｕ）－真空界面的ＳＰＰ通过表面粗糙度与外光子耦合．这一图象与该器件的电流—电压（Ｉ—Ｖ）、电流—温度（Ｉ－Ｔ）关系及其发射光谱的主要特征一致．     

电场对Au—Ag薄膜结构影响的AFM和VAXPS研究

利用原子力显微镜（ＡＦＭ）和变角Ｘ射线光电子谱（ＶＡＸＰＳ）技术研究了Ａｕ－Ａｇ／ＳｉＯ２体系在直流电场作用下，Ａｕ，Ａｇ电迁移的特点及所引起的薄膜结构的变化，观察到较低温度下Ａｕ，Ａｇ聚集状态的显著变化，发现电迁移过程中Ａｕ－Ａｇ薄膜与ＳｉＯ２基底之间存在界面化学反应，膜层中Ａｕ，Ａｇ，Ｓｉ等元素的化学状态发生了相应的变化，这些结构表明ＳｉＯ２表面上Ａｕ－Ａｇ复合薄膜电迁移不只是一个水平方向的扩     

在SrTiO3、LaAlO3和Y-ZrO2衬底上外延生长La1.85Sr0.15CuO4、La2CuO4和Nd1.85Ce0.15CuO4、Pr2CuO4薄膜

利用脉冲激光法研究了在（１００）ＳｒＴｉＯ３（ＳＴＯ）、（１００）ＬａＡｌＯ３（ＬＡＯ）和（１００）Ｙ－ＺｒＯ２（ＹＳＺ）衬底上外延生长ＬａＣｕＯ４（ＬＣＯ）,Ｌａ１．８５Ｓｒ０．１５ＣｕＯ４（ＬＳＣＯ）,Ｎｄ１．８５Ｃｅ０．１５ＣｕＯ４（ＮＣＣＯ）和Ｐｒ２ＣｕＯ４（ＰＣＯ）薄膜的工艺技术。利用Ｘ光衍射仪检测了不同条件下制备的薄膜样品结构和取向。Ｘ射线衍结果表明,在事适的制膜条件下可以在这三种衬底     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.