Synthesis and Properties of Aminomethoxy Derivatives of 1-( p -Tolyloxy)-3-(propylsulfanyl)propane

Mannich condensation of 1-(p-tolyloxy)-3-(propylsulfanyl)propane-2-ol with formaldehyde and secondary amines leads to the formation of new aminomethoxy derivatives of 1-(p-tolyloxy)-3-(propylsulfanyl)propane in yield of 68–80%. Antimicrobial activity of the obtained compounds was investigated.     

Well-dispersed polyimide/TiO2 nanocomposites: in situ sol–gel fabrication and morphological study

In the presented study, 3,5-diamino-N-(4-methyl-1-oxo-1-(phenylamino)pentan-2-yl)benzamide (V) as a new diamine monomer is synthesized and fully characterized by means of FT-IR, ¹H-NMR, ¹³C-NMR, and elemental analysis techniques. The stated diamine is used for the sol–gel fabrication of a series of polyimide (PI)/titania nanohybrid films with various titania percentages. The special design of diamine monomer containing bulky pendant group increased the flexibility of resulted PI matrixes. On the other hand, the ability to construct strong organic/inorganic H-bond lattice has led to the effective surrounding of nanoparticles by PI grounds and thus the well-dispersed quite spherical nanoparticles were created via a sol–gel procedure. The obtained nanocomposites showed high thermal stability and UV–vis absorption efficiency. The X-ray diffraction experiments confirmed the titania nanoparticles to be amorphous.     

Excess Molar Volumes and Liquid–Liquid Equilibria of the Ionic Liquid 1-Methyl-3Octyl-Imidazolium Tetrafluoroborate Mixed with Butan-1-ol and Pentan-1-ol

Experimental densities were measured for the system 1-methyl-3-octyl-imidazolium tetrafluoroborate [OMIM][BF₄] + butan-1-ol, + pentan-1-ol at 298.15 K and ambient pressure using a vibrating tube densimeter, taking into account the influence of the viscosity correction. Excess molar volumes V^E have been determined. V^E is quite small and negative in the alcohol-rich range of the mixture composition and positive in the alcohol-poor range. LLE data of [OMIM][BF₄] + pentan-1-ol have been measured using a laser light scattering cell for detecting cloud points at different compositions in the temperature range of 282–292 K. A miscibility gap with an upper critical solution temperature (UCST) of 292 K has been found.     

Study of the metabolism on tobacco-specific N-nitrosamines in the rabbit by solid-phase extraction and liquid chromatography–tandem mass spectrometry

Metabolism of four tobacco-specific N-nitrosamines (TSNAs), N′-nitrosonornicotine (NNN), N′-nitrosoanatabine (NAT), N′-nitrosoanabasine (NAB), and 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone (NNK) has been studied by solid-phase extraction (SPE) and liquid chromatography–tandem mass spectrometry (LC–MS–MS). 4-(Methylnitrosamino)-4-(3-pyridyl)-1-butanol (iso-NNAL) was used as internal standard. SPE and LC–MS–MS was found to be a rapid, simple, sensitive, and selective method for analysis of TSNAs in rabbit serum. The relative standard deviation (R.S.D., n = 6) for analysis of 5 ng mL⁻¹ and 0.5 ng mL⁻¹ standards and of serum sample spiked with 5 ng mL⁻¹ standards of five TSNAs was 2.1–11% and recovery of 5 ng mL⁻¹ standards from serum was 100.2–112.9%. A good linear relationship was obtained between peak area ratio and concentration in the range of 0.2–100 ng mL⁻¹ for NNAL and 0.5–100 ng mL⁻¹ for other four TSNAs, with correlation coefficients (R ²) >0.99 (both linear and log–log regression). Detection limits for standards in solvent were between 0.04 and 0.10 ng mL⁻¹. Doses of TSNAs administered to rabbits via the auricular vein were 4.67 μg kg⁻¹ and 11.67 μg kg⁻¹, in accordance with the different levels in cigarettes. Metabolic curves were obtained for the four TSNAs and for 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanol (NNAL), a metabolite of NNK; on the basis of these curves we modeled metabolic kinetic equations for these TSNAs by nonlinear curve fitting.     

Synthesis of some antipyrinylazo and thiazolylazo compounds with pentan-2,4-dione and their reactions with metal ions

The reagents were synthesized by using pentan-2,4-dione as the coupling component with diazotized 4-aminoantipyrine or 2-aminothiazole. Two kinds of azo compounds were obtained under different conditions: 1-(4-antipyrinylazo)-1-(4-antipyrinylhydrazino)propan-2-one (Azonol A-1) and 3-(4-antipyrinylazo)pentan-2,4-dione (Azonol A-2) from 4-aminoantipyrine, and 1-(2-thiazolylazo)-1-(2-thiazolylhydrazino)propan-2-one (TAA-1) and 3-(2-thiazolylazo)pentan-2,4-dione (TAA-2) from 2-aminothiazole. The structure of Azonol A-1 was determined by single-crystal x-ray crystallography. The reactions of these reagents with various metal ions were examined. Azonol A-1 and TAA-1 form metal chelates at low pH values. Azonol A-1 is useful as a metallochromic indicator in titrations of bismuth with EDTA at pH 0.5–2, and as a spectrophotometric reagent for copper (II) (0.2–1.5 mg l^?1) at pH 0.3–1.2.     

Synthesis and calming activity of 6<Emphasis Type="Italic">H</Emphasis>-2-Amino-4-Aryl-6-(4-<Emphasis Type="Italic">β</Emphasis>-D-Allopyranosyloxyphenyl)-1,3-Thiazine

E-(4-β-D-Allopyranosyloxyphenyl)-1-(4-substituted phenyl)propenone derivatives (1a–g) have been synthesized by the Claisen-Schmidt condensation of helicid with 4-substituted acetophenone using 10% NaOH aqueous solution as a catalyst. 6H-2-Amino-4-aryl-6-(4-β-D-allopyranosyloxyphenyl)-1,3-thiazine (2a–g) were synthesized by the 1,4-Michael reaction of 1a–g with thiourea. The structures of all the new products were established by ¹H NMR, IR, and MS spectroscopy. Compound 2b (200 mg·kg^–1) showed better sedative-hypnotic activity, so further modification of helicid should be worthwhile.     

Sensitive spectrophotometric determination of ascorbic acid in fruit juices and pharmaceutical formulations using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP)

A simple and very sensitive method has been developed for the determination of ascorbic acid based on the oxidation of ascorbic acid to dehydroascorbic acid by iron(III), followed by a complexation of iron(II) with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol(Br-PADAP). The iron(II) complex is formed immediately, with absorption maxima at 560 and 748 nm and a molar absorptivity of 1.31 × 10⁵ l mole^–1cm^–1 and 5.69 × 10⁴ l mole^–1cm^–1, respectively. The ascorbic acid determination is possible with a linear range up to 2.4 μg ml^–1, a calibration sensitivity of 0.744 ml μg^–1 at 560 nm and 0.323 ml μg^–1 at 748 nm, and a detection limit of 15 ng ml^–1 and 44 ng ml^–1, respectively. The procedure was used for the ascorbic acid determination in several fruit juices and pharmaceutical formulations. The results demonstrated a good precision (R.S.D. < 1%) and are in agreement with those obtained with others methods. The Br-PADAP method proposed is six times more sensitive than the method using the iron(II)-1,10-phenanthroline system. Received: 7 May 1996 / Revised: 1 July 1996 / Accepted: 8 August 1996     

Synthesis and photophysical behavior of thia-aza macrocycles with 9-anthracenylmethyl moiety as fluorescent appendage

1,3-Bis(bromomethyl)-2-methoxy-5-methylbenzene, 1,3-bis(bromomethyl)-2,4,6-trimethylbenzene, 1,3- and 1,4-bis(bromomethyl)benzene undergo nucleophilic substitution with methyl mercaptoacetate to provide respective diesters 6–9. These diesters (6–9) on stirring with bis(3-aminopropyl)amine and diethylenetriamine in methanol–toluene (1:1) mixture undergo intermolecular cyclization to give respective thia-aza macrocycles 10–15. The alkylation of macrocycles 10–13 with 9-anthracenylmethyl chloride gave amine N-(anthracenylmethyl) substituted macrocycles 16–19. The extraction profile of macrocycles 10–15 towards alkali (Li⁺, Na⁺, K⁺), alkaline earth (Mg²⁺, Ca²⁺, Sr²⁺, Ba²⁺), Ag⁺, Tl⁺ and Pb²⁺ picrates shows preferential extraction of Ag⁺ with these macrocycles. The macrocycles 16–19 show fluorescence spectrum typical of anthracene moiety and depending on their structures exhibit 0–80 times increase in fluorescence on addition of transition metal ions. Fluorescent receptors 16, 17, and 19 are capable of functioning as a very efficient multi input OR logic gate.

---

Graphical abstract 1,3- and 1,4-Bis(bromomethyl)benzene and its substituted derivatives undergo nucleophilic substitution with methyl mercaptoacetate to provide respective diesters 6–8. These diesters (6–8) on stirring with bis(3-aminopropyl)amine in methanol–toluene (1:1) mixture undergo intermolecular cyclization to give respective thia-aza macrocycles 10–12. The alkylation of macrocycles 10–12 with 9-anthracenylmethyl chloride gave amine N-(anthracenylmethyl) substituted macrocycles 16–18. The macrocycles 16–18 exhibit 0–80 times increase in fluorescence on addition of transition metal ions.

     

Sensitive spectrophotometric determination of ascorbic acid in fruit juices and pharmaceutical formulations using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP)

A simple and very sensitive method has been developed for the determination of ascorbic acid based on the oxidation of ascorbic acid to dehydroascorbic acid by iron(III), followed by a complexation of iron(II) with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol(Br-PADAP). The iron(II) complex is formed immediately, with absorption maxima at 560 and 748 nm and a molar absorptivity of 1.31 × 10⁵ l mole^–1cm^–1 and 5.69 × 10⁴ l mole^–1cm^–1, respectively. The ascorbic acid determination is possible with a linear range up to 2.4 μg ml^–1, a calibration sensitivity of 0.744 ml μg^–1 at 560 nm and 0.323 ml μg^–1 at 748 nm, and a detection limit of 15 ng ml^–1 and 44 ng ml^–1, respectively. The procedure was used for the ascorbic acid determination in several fruit juices and pharmaceutical formulations. The results demonstrated a good precision (R.S.D. < 1%) and are in agreement with those obtained with others methods. The Br-PADAP method proposed is six times more sensitive than the method using the iron(II)-1,10-phenanthroline system. Received: 7 May 1996 / Revised: 1 July 1996 / Accepted: 8 August 1996     

Thermal decomposition reaction of 3,3,6,6-tetramethyl- 1,2,4,5-tetroxane in 2-methoxy- ethanol solution

The thermal decomposition study of 3,3,6,6-tetramethyl-1,2,4,5-tetroxane (acetone cyclic diperoxide) was carried out in 2-methoxyethanol solution in the 130-166 °C temperature range. The overall reaction follows a first-order kinetic law up to at least 75% diperoxide conversion. The activation parameters (ΔH^# = 22.5 ± 0.7 kcal⋅mol^–1 and ΔS^# = -25.6 ± 0.5 cal⋅mol^–1⋅K^–1) for the unimolecular rupture of the O–O bond in the diperoxide molecule were obtained by measuring the remnant diperoxide at different reaction times by the CG technique. Acetone was detected by GC as the major organic product of the reaction.     

Development of a new flow-through bulk optode for the determination of manganese(II)

A flow-through bulk optode based on the use of 1-(2-pyridylazo)-2-naphthol (PAN) immobilized in a plasticized poly(vinyl chloride) membrane entrapped in a cellulose support, in conjuntion with the flow injection analysis technique, is proposed for the determination of manganese(II). The calibration graph obtained at 570 nm was linear in the range 0.27–27.5 mg L^–1 (5 × 10^–6– 5 × 10^–4 M) Mn(II) with a detection limit of 0.18 mg L^–1. The coefficients of variation of the sensor response for 5.5 mg L^–1 of Mn(II) were ±0.22% for consecutive measurements (n = 10), ±0.48% between days (n = 5) and ±0.38% between different membranes (n = 6). The sensor was readily regenerated with the carrier acetic acid/acetate buffer of pH 4.5. The method was applied to the determination of manganese in steels, waters and lemon tree leaves. Received: 13 December 2000 / Revised: 25 January 2001 / Accepted: 26 January 2001     

Experimental and theoretical studies on the reactions of 1-amino-5-benzoyl-4-phenyl-1<Emphasis Type="Italic">H</Emphasis>-pyrimidine-2-one/-thione compounds with ethyl acetoacetate

The reaction of 1-amino-5-(4-methylbenzoyl)-4-(4-methylphenyl)pyrimidin-2(1H)-one/-thione (1a,b) with ethyl acetoacetate (EA) afforded moderate to good yields (59–63%) of ethyl 2-methyl-4-(4-methylbenzoyl)-5-(4-methylphenyl)-7-oxo/-thioxo-3,3a-dihydropyrazolo[1,5-c]pyrimidine-3-carboxylate (2a,b). The newly synthesized compounds were characterized by elemental analyses, IR, ¹H and ¹³C NMR spectral data. All were compared with their previous analogues. The reaction mechanism of 1 with EA was studied by means of the B3LYP/6-31G(d,p) method. In addition, for reactants Fukui functions were performed using the data calculated with the Becke3–Lee–Yang–Parr (B3LYP) hybrid function.     

Voltammetric determination of cadmium(II) using a chemically modified electrode

An 1-(pyridylazo)-2-naphthol modified glassy carbon electrode has been investigated as sensor for the measurement of trace levels of Cd²⁺. Cd²⁺ is deposited on the surface of a PAN modified glassy carbon electrode at –1.10 V (vs. SCE) via forming Cd²⁺–PAN and subsequent reduction at the electrode. In the following step, Cd-PAN is oxidized, and voltammograms are recorded by scanning the potential in a positive direction. Calibration plots were found to be linear in the range 2 × 10^–8 mol/L to 8 × 10^–7 mol/L. The detection limit was 5 × 10^–10 mol/L, and the coefficient of variation, determined on one single electrode at a concentration of 5 × 10^–7 mol/L, was calculated to be 3.2% (n = 5). Using this new kind of modified electrode, trace levels of Cd(II) in water samples were determined; the average recovery was calculated to be 98.78%. Received: 17 August 2000 / Revised: 19 December 2000 / Accepted: 27 December 2000     

Spectrophotometric flow injection determination of trace iodide in table salt and laver through the reaction of iodate with 3,5-Br2-PADAP and thiocyanate

A new simple, rapid and sensitive spectrophotometric flow injection method for the determination of trace iodide is described based on an ion associate of iodate (IO₃ ^–) with 2- (3,5-dibromo-2-pyridylazo)-5-diethylamino-phenol (3,5-Br₂-PADAP) and thiocyanate (SCN^–). In a strongly acidic medium, this unstable violet product was formed with an absorption maximum at 605 nm. Flow injection is an ideal method to reproducibly monitor the transient signal. Various parameters were optimized using the Super Modified Controlled Weighted Centroid Simplex Method (SMCWC). Under the optimum experimental conditions, iodide could be determined in the range of 1.00 × 10^–6 and 2.4 × 10^–5 mol l^–1. The correlation coefficient of the calibration curve is 0.9991. With a sampling frequency of 80 h^–1, the detection limit for iodide is 5.0 × 10^–7 mol l^–1. The proposed method has been applied to the determination of trace iodide after oxidizing I^– in table salt or laver to IO₃ ^–. In addition, the mechanisms of the ion association reaction was studied. Received: 15 August 1996 / Revised: 10 October 1996 / Accepted: 16 October 1996     

Synthesis, structural characterization and thermal properties of three copper(II) complexes based on aryl hydrazide ligands

The thiosemicarbazide and hydrazide Cu(II) complexes, [Cu₃L₂¹(py)₄Cl₂] (1), [Cu(HL²)py] (2) and [Cu(HL³)py] (3), (H₂L¹ = 1-picolinoylthiosemicarbazide, H₃L² = N′-(2-hydroxybenzylidene)-3-hydroxy-2-naphthohydrazide, H₃L³ = 2-hydroxy-N′-((2-hydroxy-naphthalen-1-yl)methylene)benzohydrazide) have been prepared and characterized through physicochemical and spectroscopic methods as well as X-ray crystallography. Complex 1 has a centrosymmetric structure with –N–N– bridged Cu₃ skeleton. Neighboring molecules are linked into a 3D supermolecular framework by π–π stacking interactions, N–H···Cl and C–H···Cl hydrogen bonds. Complexes 2 and 3 have similar planar structures but different dimers formed by concomitant Cu···N and Cu···O interactions, respectively. Solvent accessible voids with a volume of 391 ?³ are included in the structure of complex 2, indicating that this complex is a potential host candidate. Thermogravimetric analysis shows that the three complexes are stable up to 100 °C.     

Morphology and electric conductivity of cross-linked polyethylene–carbon black blends prepared by gelation/ crystallization from solutions

 Ultra-high-molecular-weight polyethylene (UHMWPE) – carbon black (CB) blends were prepared by gelation/ crystallization from PE dilute solutions containing CB particles. The UHMWPE/CB composition chosen were 1/0.15, 1/0.25, 1/0.5, 1/0.75, 1/1, 1/3, 1/5, and 1/9, etc. The cross-linking of PE chains was performed by chemical reaction of dicumyl-peroxide at 160 ^°C. X-ray diffraction patterns indicate that the crystallinity of PE within the blends decreased drastically through the chemical reaction at high temperature. The sample preparation method by gelation/crystallization provided the UHMWPE–CB system with various CB contents up to 90% and the conductivities for the resultant specimens were in the range from 10^-9 to 1 Ω^-1 cm^-1 corresponding to the electric conductivity range of semiconductors. The blends assured thermal stability of electric conductivity by cross-linking of PE chains, although the mechanical property such as the storage and loss moduli were very sensitive to temperature. The conductivity of the blends with CB content ≥20% were almost independent of temperature up to 220 ^°C and the values in the heating and cooling processes were almost the same. On the other hand, for the UHMWPE–CB blends with 13% CB content corresponding to the critical one, temperature dependence of electric resistivity showed positive temperature coefficient (PTC) effect. The PTC intensities for non-cross-linked and cross-linked materials were lower than that of the corresponding low-molecular-weight-polyethylene (LMWPE)–CB blend but the maximum peak appeared at 160 ^°C which is higher than the peak temperature of LMWPE–CB blend. Received: 10 December 1997 Accepted: 9 April 1998     

LC-MS-MS Determination of Cyclo{(2S)-2-amino-8-[(aminocarbonyl)hydrazono] decanoyl-1-l-tryptophyl-l-isoleucyl-(2R)-2-piperidinecarbonyl} a Novel Histone Deacetylase Inhibitor in Rat Serum

A rapid and sensitive liquid chromatography-tandem mass spectrometry assay was developed for the determination of a novel histone deacetylase inhibitor, cyclo{(2S)-2-amino-8-[(aminocarbonyl)hydrazono]decanoyl-1-l-tryptophyl-l-isoleucyl-(2R)-2-piperidinecarbonyl} (SD-2007), in rat serum. The mobile phase consisted of acetonitrile and ammonium formate (10 mM) (85:15 v/v), and the flow rate was 0.25 mL min⁻¹. Chromatographic separations were achieved by isocratic elution on a C₁₈ column. Multiple reaction monitoring was based on the transition of m/z = 681.8 → 83.6 for SD-2007 and 372.1 → 176.1 for trazodone (internal standard). A linearity was observed over a concentration range from 2 to 1,000 ng mL⁻¹ (r ² > 0.999), with the lower limit of quantification at 2 ng mL⁻¹ with 100 μL of rat serum. The mean intra- and inter-day assay accuracy ranged from 98.5–109.7% to 95.2–102.7%, respectively, and the mean intra- and inter-day precision was between 4.3–11.3% and 2.9–13.3%. The developed assay was applied to a pharmacokinetic study of SD-2007 in rats after intravenous injection (dose 4 mg kg⁻¹).     

Sulfur speciation by capillary zone electrophoresis: conditions for sulfite stabilization and determination in the presence of sulfate, thiosulfate and peroxodisulfate

Capillary zone electrophoresis (CZE) was used for the separation of the sulfur species SO₃ ^2–, SO₄ ^2–, S₂O₃ ^2– and S₂O₈ ^2–. Using an electrolyte system with 9.5 mmol L^–1 potassium chromate as UV-absorbing probe and 1 mmol L^–1 diethylenetriamine (DETA) as electroosmotic flow modifier, various possibilities for the stabilization of sulfite and electrophoretic separation of the sulfur anions were investigated. By adding 5% propanol as a stabilizer to both the working electrolyte and the sample solution, a good stabilization for sulfite and a separation of the sulfur anions in a short analysis time (4 min) was achieved. The advantages by using propanol instead of other stabilizers often used in analytical techniques are discussed. The electrophoretic separation of the sulfur anions was optimized with respect to the pH of the working electrolyte and concentration of the electroosmotic flow modifier (DETA). The detection limits achieved for SO₃ ^2–, SO₄ ^2–, S₂O₃ ^2– and S₂O₈ ^2– were 0.35, 0.25, 0.78 and 0.80 mg L^–1, respectively. Received: 16 December 1999 / Revised: 7 March 2000 / Accepted: 14 March 2000     

4-(1-Alkylbenzimidazol-2-ylazo)-2-pyrazolin-5-ones: specific features of prototropic tautomerism

Quantum chemical calculations, ¹H and ¹³C NMR, and X-ray studies showed that, in contrast to 4-arylazo-2-pyrazolin-5-ones, 4-(1-alkylbenzimidazol-2-ylazo)-2-pyrazoline-5-ones mainly exist in the condensed phase as unusual ketoazine tautomers of high polarity, while the ketohydrazone tautomer stabilized by intramolecular hydrogen bond apparently predominates in the gas phase. According to calculations, various types of tautomerism are possible for 4-(benzimidazol-2-ylazo)-2-pyrazolin-5-ones, including mono- and bimolecular 1,3-, 1,5-, and 1,7-prototropic migrations proceeding by the single- and double-proton transfer mechanism with low activation energies (ΔE ^≠ ≈ 2–14 kcal mol⁻¹). Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1467–1478, July, 2008.     

Constant-volume combustion energy of the lead salts of 2HDNPPb and 4HDNPPb and their effect on combustion characteristics of RDX–CMDB propellant

The constant-volume combustion energies of the lead salts of 2-hydroxy-3,5-dinitropyridine (2HDNPPb) and 4-hydroxy-3,5-dinitropyridine (4HDNPPb), ΔU _c (2HDNPPb(s) and 4HDNPP(s)), were determined as –4441.92±2.43 and –4515.74±1.92 kJ mol^–1 , respectively, at 298.15 K. Their standard enthalpies of combustion, Δ_c ^m H θ(2HDNPPb(s) and 4HDNPPb(s), 298.15 K), and standard enthalpies of formation, Δ_r ^m H θ(2HDNPPb(s) and 4HDNPPb(s), 298.15 K) were as –4425.81±2.43, –4499.63±1.92 kJ mol^–1 and –870.43±2.76, –796.65±2.32 kJ mol^–1 , respectively. As two combustion catalysts, 2HDNPPb and 4HDNPPb can enhance the burning rate and reduce the pressure exponent of RDX–CMDB propellant.