Non-destructive neutron activation analysis of atmospheric pollutants

Concentration of elements in atmospheric particulate of urban areas has been determined by employing a Ge(Li) detector. In the first part of this study, a single area was selected and samples were collected on millipor filter during three seasons of the year and their results were compared. These results were also compared with the concentration of the same elements reported for other cities. We have concluded that in a dry climate at least two parameters are involved in seasonal changes of trace elements in the atmosphere. They are the rate of wet deposition and reduction of vertical diffusion of airborne particulates.     

Microwave assisted sample preparation for determining water-soluble fraction of trace elements in urban airborne particulate matter: evaluation of bioavailability

The feasibility of using two different microwave-based sample preparation methods was investigated to determine the total and water-soluble trace metal fraction in airborne particulate matter. The extraction techniques were then applied to urban particulate matter of different sizes in order to evaluate their bioavailability of associated trace metals. While a combination of HNO₃-HF-H₂O₂ was used for the total trace metal fraction of particulate matter, water was employed for the microwave-assisted extraction of water-soluble trace metal fractions. Inductively coupled plasma-mass spectrometry (ICP-MS) was used for the analysis of trace elements. The experimental protocol for the microwave assisted digestion was established using two different SRMs (1648, urban particulate matter and 1649a, urban dust). In the case of water-soluble trace metal fraction, the quantities extracted from the SRMs were compared between ultrasonic and microwave-assisted extractions, and there was a good agreement between the two extraction methods. Blanks values and limits of detection (LODs) for total and water-soluble trace metal concentrations were determined for three different filter substrates (Teflon, Zeflour, and Quartz). Subsequently, the proposed digestion method was evaluated for its extraction efficiency with these filter substrates. Finally, the real-world application of the proposed microwave-based sample preparation methods was demonstrated by analyzing trace elements in airborne particulate samples collected from different outdoor environments in Singapore. The solubility of 11 trace elements detected in the particulate samples is quantified.     

The determination of silicon in airborne particulate matter by XRF and LA-ICP-MS

This study reports the analysis of Si in airborne particulate matter by laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) as well as X-ray fluorescence (XRF). It was found that Si concentration in airborne particulates collected on PTFE-membrane filters could be accurately determined with a laser beam operated at 160 mJ free running mode, 6.5 mm defocusing distance and 0.8 l/min carrier gas flow rate during the LA-ICP-MS measurement. Standard filters prepared by NIST SRM 1648 urban particulates were used for both XRF and LA-ICP-MS not only to establish the calibration curves of Si, but also to examine the proposed method's effectiveness. The capability of applying both methods for natural sample analysis was also examined. Particulate loaded filter samples collected from a heavily polluted metropolitan area of Kaoshiung, Taiwan were initially measured by XRF, then by LA-ICP-MS. An intercomparison between them was thus performed. As a result, both XRF and LA-ICP-MS proved to be the valid analytical methods for directly determining Si concentrations in airborne particulates on PTFE membrane filters.     

Determination of silver traces in air by neutron activation analysis

A non-destructive system for determination of silver traces in air particulates collected on cellulose filters is described, based on neutron activation followed by¹¹⁰Ag β⁻ counting instead of the 657.7 keV γ-ray. The determination limit (for 10% confidence limit) is estimated to be about 10⁻⁹ g. The method is easily applicable to the determination of silver in cloud seeding experiments, since the filters themselves provide a consistent and fairly uniform source and samples are collected in general far from industrial areas, where the concentration of possible interfering elements in air is reasonably low.     

Toxic elements content in PM<Subscript>10</Subscript> samples from a coastal area of the Northern Adriatic Sea

PM₁₀ samples were collected during winter and summer seasons at two different sites in the area of Trieste (Italy). The content of As, Cd, Cr, Mn, Ni, Pb and V in the PM₁₀ samples was determined by inductively coupled plasma-mass spectrometry, with the purpose of evaluating the relevance of PM₁₀ inhalation as a route of human exposure to these elements. The results showed that the ambient air concentration of the aforementioned elements were below the limits or target values for both sites and season. Site and season-specific correlation analysis was conducted for the identification of metals with similar origin: very good correlation for the couple Ni-V was found in both sites and seasons, showing the influence of combustion of heavy oils in PM₁₀ composition. The inter-site and seasonal variability of both PM₁₀ and metal concentrations were examined. A stronger impact by the vehicular traffic on the PM₁₀ and metal concentrations was found for the urban site in both seasons. Because of the great importance of the “Bora” wind on the local climate, variability of PM₁₀ and toxic elements concentration with wind were analysed, allowing determination of the effect of wind on dilution of the pollutants for the urban site during both seasons.      

Determination of elemental composition of atmospheric aerosol in the urban area of Islamabad, Pakistan

Summary This study provides useful information about the level and chemical composition of particulate matter and about the possible sources of the aerosol pollutant in Islamabad, the capital of Pakistan. Atmospheric aerosol samples were collected during winter (January and February) 1995, from two locations of Islamabad, namely of Sector F-7 and Sector I-9. Twenty-four elements were detected by using thermal neutron activation analysis (NAA) and atomic absorption spectrometry (AAS). The concentration of total suspended particulates (TSP) in the area around the industrial sector (I-9) was found to be more than twice higher (297 μg/m³) than in the Sector F-7 (133 μg/m³). The enrichment factor analysis revealed Zn, As, Br, Sb, I and Pb, originated mainly from anthropogenic sources. The elemental ratio analysis indicated that both Sectors I-9 and F-7 are under the influence of coal burning processes whereas transportation is responsible for the toxic pollutants Pb and Br. The present results were discussed and compared with those of the literature. The results may also serve as base line level as this work employed samples collected in 1995 and many of the air environmental change factors occurred after the sampling year.     

Atomic emission spectrometric analysis of airborne particulate matter by direct nebulization of suspensions into the inductively-coupled plasma

A method is described for the rapid, direct emission spectrometric determination of iron in airborne particulate matter collected on polystyrene fiber filters using a conventional high-volume sampler and a Japanese low-volume sampler. The suspension prepared by dissolving the filter material in xylene was directly nebulized into the inductivelycoupled plasma excitation source. An ultrasonic immersion device was used for stirring purposes. Particles within the size range 0.1–100 μm in diameter are collected on the high-volume filters, while the largest particles on low-volume filters do not exceed 10 μm in diameter. The difference in the particle size composition entailed the use of a separate set of standard suspensions for each sample type. Standard suspensions for calibration were prepared from NBS SRM-1648 (urban particulates) as originally received and from its ground powder for high-volume and low-volume samples, respectively. The relative standard deviation was usually below 5%, which is acceptable for large-scale air pollution survey work. The possibility of determining other major and minor elements in airborne particulate matter was also examined.     

Study on air pollution monitoring in Korea using instrumental neutron activation analysis

Trace elements in airborne particulate matter collected monthly at suburban and rural areas in Korea were analyzed by instrumental neutron activation analysis (INAA). Neutron irradiation of the samples was done at the irradiation hole (neutron flux 1·10¹³ n·cm^–2·s^–1) of the TRIGA Mark-III Research Reactor in the Korea Atomic Energy Research Institute. For the verification of the analytical technique, two reference materials, NIST SRM-1648 and NIES CRM-8, were chosen for analysis. The accuracy and precision of the determinations of the 40 elements were compared with the reference values. We used this method (1) to analyze 30 trace elements in airborne particulate matter collected monthly with the high volume air sampler (PM-10) at two different locations and (2) to confirm the possibility of using this method as a routine monitoring tool to find out environmental pollution sources.     

The determination of ammonium ion in airborne particulates with selective electrodes

The accurate and rapid measurement of ammonium ion in airborne particulates is described, with particular reference to so-called high-volume air samples collected on glass-fibre filters. The method involves aqueous extraction of a part of the filter followed by analysis with a selective electrode; an Orion ammonia electrode and a Beckman ammonium electrode were compared. Varying ionic strength of the sample extracts had no effect and small interferences by other elements with the Beckman electrode could be taken into account. For a typical air sample of 2000 m³, the ammonium content could be determined accurately down to 0.03 μg m^-3. The accuracy was established by comparison with an absorptiometric method. Recovery of standard added ammonium was quantitative. Three different methods of extraction were compared.     

Mobility of important toxic analytes in urban dust and simulated air filters determined by sequential extraction and GFAAS/ICP-OES methods

The modified BCR three-step sequential extraction procedure has been applied to homogenized urban dust samples and to simulated air filters loaded with the prepared urban dust via the wet deposition procedure. This work has been focused on comparative study of the distribution of trace elements in both samples and evaluation of the factors influencing the reliability of results with respect to the proposed extraction procedure. Extracted chemical fractions were analyzed by ICP-OES and GFAAS depending on the concentration levels of investigated trace elements As, Cd, Cr, Mn, Ni, and Pb, selected according to their adverse effect on the human health. Statistically evaluated results indicate significant differences between the extracted portions of analytes in urban dust and simulated air filters, where the mobility of some analytes in simulated air filters was higher than that in urban dust samples. The impact of surfactant Triton X-100 (0.05 vol. %) on the extraction procedure was also investigated. Presented at the XVIIIth Slovak Spectroscopic Conference, Spišská Nová Ves, 15–18 October 2006.     

Risk assessment of inhalation exposure for airborne toxic metals using instrumental neutron activation analysis

In order to study the effects of air pollution, about 1,300 samples of airborne particulate matter (APM) were collected at suburban and industrial sites, in Daejeon, Korea from 1998 to 2006. The concentrations of carcinogenic (As and Cr) and non-carcinogenic metals (Al, Mn, and Zn) were determined by using instrumental neutron activation analysis (INAA). These long-term metal concentration data were applied to a risk assessment of inhalation exposure using Monte Carlo analysis (MCA).     

Analysis of urban dust (PM<Subscript>2</Subscript>/PM<Subscript>10-2</Subscript>) in Daejeon city by instrumental neutron activation analysis

Summary As part of an air pollution monitoring study, airborne particulate matter (PM₂/PM_10-2) samples were collected from 2000 to 2003 at two sampling sites in an urban region, Daejeon, the middle of Korea. Mass concentrations of both fine and coarse fractions and that of the black carbon in the fine particles were measured using the Gent stacked filter unit sampler and the smoke stain reflectometer, respectively. In the collected samples the concentrations of 24 elements were analyzed using instrumental neutron activation analysis. Monitored data were investigated for their temporal trends under different environmental conditions and their seasonal correlation patterns. Crustal enrichment factors were also estimated to establish the contribution between anthropogenic and crustal origin. Patterns for airborne particle matter (APM) and elemental concentrations, seasonal variation of some marker elements were investigated. The results can be applied for the investigation of further air pollution sources and for the evaluation of air quality.     

Trace element levels of aerosols at an urban area of Korea by instrumental neutron activation analysis

Instrumental neutron activation analysis was used to measure the concentrations of about 27 elements associated with airborne PM 10 samples that were collected from a roadside sampling station at a moderately polluted urban area of Taejon city, Korea. The magnitude of their concentrations was clearly distinguished and spanned over four orders. If compared in terms of enrichment factors, it was found that certain elements (e.g., As, Br, Cl, Sb, Se, and Zn) are enriched in PM 10 samples of the study site. The factor analysis indicated three factors with statistical significance, which may exert dominant controls on regulating the metal concentration levels in the study area.     

Effects of temperature on the concentration of polycyclic aromatic hydrocarbons (PAHs) adsorbed onto airborne particulates

Summary Daily samples of airborne particulates (143) were collected along the year in La Spezia (Italy). Seasonal variations of atmospheric PAH concentrations, with highest winter values, have been observed. The concentration of PAHs was found to correlate negatively with the mean ambient temperature during the sampling period. Volatilization, photodegradation and seasonal modifications of emissions from urban traffic were found to be a possible explanation of this phenomenon.     

Air pollution monitoring of an urban dust in Daejeon city,Korea by using instrumental neutron activation analysis

For air pollution monitoring, about 1300 airborne particulate matter samples were collected by using a low volume air sampler and a polycarbonate filter at two sampling sites in an urban region, Daejeon, the middle of Korea from 2003 to 2006. Mass concentrations of the black carbon were measured using a smoke stain reflectometer. The concentrations of 24 elements in the collected samples were analyzed by using instrumental neutron activation analysis, and its temporal trends and enrichment factors were investigated under different environmental conditions. Analytical control was carried out by using certified reference materials.     

Chemical characterization of airborne particulate matter in ambient air of Nagoya, Japan, as studied by the multielement determination with ICP-AES and ICP-MS.

The multielement determination of PM(10) (airborne particulate matter smaller than 10 microm) samples, which was collected by a high volume air sampler at the urban site of Nagoya City, was carried out by inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). The present analytical method was validated by analyzing urban particulate matter standard reference material of NIST SRM 1648. The analytical data for ca. 30 elements in PM(10) samples collected during a period from 8 September to 9 October, 2003, were obtained in the concentration range from sub-microg g(-1) to several-10 mg g(-1), but the data for 18 elements among ca. 30 elements were available for the characterization of PM(10) samples in ambient air, because of problems caused by the filter blanks. Then, the trends concerning the distributions of diverse elements in PM(10) samples were analyzed based on the enrichment factors and size distribution factors. The lithophile and siderophile elements were distributed more than 50% in coarse particle fraction (>2.1 microm), which was derived mainly from natural sources, such as soils and crustal minerals. On the other hand, chalcophile elements were distributed more than 50% in fine particle fraction (<2.1 microm), which was derived mostly from anthropogenic emission sources. The large enrichment of chalcophile elements in PM(10) samples as well as their mining influence factors (MIFs) suggested their wide use in industrial productions.     

Aldehydes in the atmospheric environment: evaluation of human exposure in the north-west area of Milan

Human exposure to aldehydes has been evaluated in five urban locations and one rural-industrial location in the north-west area of Milan in winter 1999 and in summer 1998–99. Ambient air samples collected on dinitrophenylhydrazine (DNPH)-coated diffusive cartridges were analysed for aldehydes as their DNPH-derivatives. Aldehydes have been identified and their concentration measured via HPLC-UV and LC-APCI-MS negative ion mode methods. During the winter the range of total concentration of aldehydes was 16.7–30.7 μg/m³ at the urban locations and 11.7 μg/m³ at the rural-industrial location. Formaldehyde accounted for 50% of the total amount of carbonyl compounds in all locations; the percentage of acetaldehyde was more variable: 23–38% of the total carbonyls. The contribution of outdoor environment to the average human daily intake of formaldehyde in this area (urban and rural-industrial) is mostly 1–2% of the total human exposure.     

N-Alkanes in Air Particulates of the Eastern Province of Saudi Arabia

Abstract

Oil hydrocarbons represent a great proportion of organic compounds in the atmosphere. Information about these compounds in the atmosphere of the Eastern Province of Saudi Arabia is lacking. In this study, n-alkanes and polynuclear aromatic hydrocarbons in air particulates were determined. The highest median concentration levels of n-alkanes in three urban areas and three areas near oil production centers were 121 ng/m³ and 42.9 ng/m³, respectively. Polynuclear aromatic hydrocarbons were also detected, although they are present in too low concentration for reliable quantitative measurement by GC and GC/MS techniques. A positive correlation was found between the concentration levels of n-alkanes in air particulates and the total suspended particulates measured at most locations. The carbon preference index (CPI) and the presence of the unresolved complex envelope suggested an anthropogenic origin for the n-alkanes.     

Comparative study of pretreatment methods for the determination of metals in atmospheric aerosol by electrothermal atomic absorption spectrometry

A comparative study of pretreatment methods for the determination of 10 elements (As, Cd, Pb, V, Ni, Mn, Cr, Cu, Fe, Al) in atmospheric aerosols by electrothermal atomic absorption spectrometry (ETAAS) was conducted. For the digestion of the particulates collected in filters, six methods were compared using a mixture of HNO₃ and HF with or without the addition of various oxidative agents (HClO₄ or H₂O₂) or acids (HCl). The comparative study was performed using loaded cellulose filter samples, which were digested in Parr bombs and heated in a conventional oven at 170 °C for 5 h. The extraction efficiency and blanks were compared and it was proved that the digestion method using only HNO₃–HF extracted most of the metals and gave the lowest blanks. The HNO₃–HF mixture was selected for the development of an improved microwave digestion method specific for aerosol-loaded filters. The operating parameters were optimized, so that quantitative recovery of the reference materials NIST 1649a urban dust and NIST 1648 urban particulate matter was achieved. The blank of cellulose and teflon filters were also determined and compared. Teflon filters present the lowest blanks for all the elements. The obtained limits of detection for each type of filters were adequate for environmental monitoring purposes. ETAAS instrumental operation was also optimized for the compensation and the elimination of interferences. The temperature optimization was performed for each metal in every type of filter and optimized parameters are proposed for 10 elements.     

Determination of heavy metals in air conditioner dust using FAAS and INAA

The elements Cd, Cr, Cu, Mn, Ni, Pb and Zn were determined in dust samples collected from air conditioner (AC) filters from 15 commercial sites of Lahore using flame atomic absorption spectroscopy (FAAS). The elements Cr, Mn and Zn were also determined using instrumental neutron activation analysis (INAA). The results obtained showed that higher amounts of these metals were measured in these dust samples than normally found in soil. This was especially true for Cd, Cu, Pb and Zn. Generally the amounts of Cd, Cr and Mn did not vary throughout the city of Lahore but the amounts of the traffic related Cu, Pb and Zn elements had the more variable ranges of 30–140, 30–230 and 74–2810 mg/kg respectively. The concentrations obtained for Cr, Mn and Zn by INAA were found to be higher than those obtained using FAAS. Analysis of the data obtained showed the digestion procedure employed to be the possible cause for this occurrence. It was also found that Mn was being over-estimated by INAA due to the interference from the Mg peak.