Ionic transport in the Na2SO4Na2WO4 and Na2SO4M2(SO4)3 (M=La,Dy, Sm,In) systems

Premelted, predried Na₂SO₄, premelted Na₂WO₄, Na₂SO₄Na₂WO₄ composites and Na₂SO₄M₂(SO₄)₃ (M = La, Dy, Sm, In) have been studied by means of X-ray diffraction, DTA and electrical conductivity measurements. The high temperature, highly conducting Na₂SO₄ phase I has been successfully stabilised at room temperature; the Na₂SO₄ containing 4 mole% La₂(SO₄)₃ exhibits the highest conductivity (σ) and lowest activation energy (E_a) (σ=1.08 × 10⁻³ω⁻¹ cm⁻¹ at 290°C and E_a=0.50 eV) and therefore this system appears promising for further development.     

Effect of pressure on the solubilities of LiF,NaF, KCl,NH4, Cl,K2SO4, (NH4)2SO4, and ZnSO4·7H2O in water at 298.15 K

Abstract

Solubilities of seven inorganic compounds in water were measured at 298.15 K and up to 350 MPa. The solubilities of K₂SO₄, LiF, NaF, and KCI increased with increasing pressure, those of NH₄Cl and (NH₄)₂SO₄ decreased, and that of ZnSO₄·7H₂O showed almost no dependence on pressure. From the slopes of these solubility curves at 0.1 MPa, we estimated the volume changes accompanying the dissolution of the solutes. These values coincided with the volume differences between the partial molar volume at saturation and the molar volume of the crystal within ca. ± 1 cm³ mol^?.     

Defect structure of Cu2+ center in K2SO4‒Na2SO4‒ZnSO4 glasses

The spin Hamiltonian parameters (g factors g _//, g _⊥ and hyperfine structure constants A _//, A _⊥) of Cu²⁺ in K₂SO₄?Na₂SO₄?ZnSO₄ glasses are calculated from the high-order perturbation formulas of 3d⁹ ion in tetragonal octahedral sites. The calculated results are in agreement with the observed values. Since the EPR parameters are sensitive to the local structure of a paramagnetic impurity center, the defect structure of Cu²⁺ center in K₂SO₄?Na₂SO₄?ZnSO₄ glasses is estimated. The validity of results is discussed.     

Ti(SO4)2水热法制纳米SO2-4/TiO2光催化剂的光谱研究

以Ti(SO4) 2 水溶液为前驱物 ,尿素为沉淀剂 ,采用水热沉淀 加热分解 浸渍烧结法制备纳米SO2 -4/TiO2 固体超强酸光催化剂 ,并用XRD ,BET ,FTIR ,DRS和FS等对中间态粒子和产物进行表征 ,以光催化降解罗丹明B为模型反应 ,筛选制备SO2 -4/TiO2 光催化剂的优化条件。结果表明 ,用Ti(SO4) 2 为前驱物 ,水热法能在较低的温度、弱碱性介质中 ,得到纳米锐钛矿型TiO2 晶体 ;在 30 0℃下控制焙烧 4h ,基本能使水热反应副产物 (NH4) 2 SO4等分解 ,又避免H2 SO4大量的流失 ;SO2 -4负载量和烧结时间是影响SO2 -4/TiO2 光催化活性的主要因素 ,当SO2 -4负载量 11%、烧结温度 4 5 0℃时 ,制备的SO2 -4/TiO2 光催化剂活性较高 ,达P 2 5光催化剂的水平     

Thermoluminescence of γ-irradiated BaCa(SO4)2:Eu,Dy

In this paper, thermoluminescence (TL) studies of BaCa(SO₄)₂:Eu,Dy phosphor are reported. A microcrystalline sample of BaCa(SO₄)₂:Eu,Dy was prepared by a solid state diffusion method and the formation of the compound was confirmed by the X-ray diffraction study. Morphology of the phosphor was analyzed by scanning electron microscopy (SEM). The sample is found to have an average particle size of 5?µm. TL glow curves of the γ-irradiated samples with different concentrations of Eu and Dy were studied and compared with BaCa(SO₄)₂:Eu and BaCa(SO₄)₂:Dy. It has been found that a single peak was located at around 230°C with the highest TL intensity in BaCa(SO₄)₂:Eu,Dy which is eight times and two times more than singly Dy- and Eu-doped BaCa(SO₄)₂ phosphor, respectively. For TL analysis, BaCa(SO₄)₂:Eu,Dy (0.2?mol%, 1?mol%) is annealed at different temperatures ranging from 900°C to 1100°C. Analysis of the TL glow curve was carried out by a glow curve deconvoluted method. Trapping parameters (activation energy and frequency factor) of all TL glow curves were evaluated by Chen's peak shape method. A comparison of trapping parameters between BaCa(SO₄)₂:Eu,Dy; BaCa(SO₄)₂:Eu and BaCa(SO₄)₂:Dy phosphors at 900°C, 1000°C and 1100°C is also reported in this paper.     

γ-irradiation effect on the spectroscopic and electrical properties of K2SO4—Na2SO4 mixed system

Abstract

Measurements of electron paramagnetic resonance, infrared and electrical properties were carried out for the K₂SO₄—Na₂SO₄ mixed system before and after γ-irradiation. EPR measurements revealed the presence of a quartet of lines characterized by an isotropic g-value of 2.0034. These lines are mainly attributed to the formation of a SO^? ₃ center which results from the interaction of γ-rays with the sulfate ion. A decrease in the absorption intensity of the Infrared radiation was observed after γ-irradiation due to radiation damage in the sulfate group. The electrical conductivity, σ, was measured for the K₂SO₄—Na₂SO₄ system before and after γ-irradiation in the temperature range from 30 up to 430°C. A considerable decrease in the conductivity value accompanied by an increase in the activation energy was observed after γ-irradiation. The energy of formation of Frenkel defects was estimated to be 2.94eV. The current-voltage characteristics were measured at different temperatures in order to estimate the type of conduction in the samples. Isothermal annealing kinetics was investigated at different temperatures before and after γ-irradiation. The electrical conductivity decreases with increasing time of annealing and the annealing process is dominated by a unique rate process.     

Comparative study of aerogels nanostructured catalysts: Ni/ZrO2–SO4 2− and Ni/ZrO2–Al2O3–SO4 2−

Ionics - A series of Ni/ZrO2–SO4 2− and Ni/ZrO2–Al2O3–SO4 2− catalysts were prepared in one step by the sol–gel method and dried in hypercritical conditions of...     

光催化剂SO2- 4/TiO2和TiO2 的光谱行为比较

用ＩＲ、Ｒａｍａｎ和ＤＲＳ光谱研究了ＳＯ＾２－４／ＴｉＯ２光催化剂和ＴｉＯ２光催化剂的光谱行为差别。结果表明,ＴｉＯ２光催化剂的表面只有Ｌ酸中心,而ＳＯ＾２－４／ＴｉＯ２光催化剂表面既有Ｌ酸中心也有Ｂ酸中心。ＴｉＯ２的硫酸化有效地抑制了晶相转变和晶粒度的增加。与ＴｉＯ２相比,ＳＯ＾２－４／ＴｉＯ２光催化剂的锐钛矿相含量较多、晶粒较小、光谱吸收边蓝移,从而增大了光吸收阈值,增强了光生空穴和电子的氧化     

紫外薄层色谱法分离C15H18N4SO2和C13H19N3SO4

采用紫外薄层色谱法在硅胶GF254板上分离N-{2-[(2,2-二氰基-乙烯基)-甲基-氨基]-丙基}-4-甲基-苯磺酰胺(C_(15)H_(18)N_4SO_2)和4-甲基-N-{2-[甲基-(2-硝基-乙烯基)-氨基]-丙基}-苯磺酰胺(C_(13)H_(19)N_3SO_4)二种有机物的方法。硅胶GF254板由0.27mol/L,pH=7的EDTA溶液修饰,避免了这两种样品与板上少量无机金属离子发生络合作用;展开剂为乙酸乙酯-石油醚-乙醇-37.5%氨水(体积比为10∶10∶1∶1)。C_(15)H_(18)N_4SO_2和C_(13)H_(19)N_3SO_4的Rf值分别为0.64和0.48。用紫外薄层色谱法分离C_(15)H_(18)N_4SO_2和C_(13)H_(19)N_3SO_4具有操作简单,灵敏,准确的特点。     

离子色谱测定土壤中Cl-和SO2-4

介绍了离子色谱法测定土壤中Cl-和SO2-4的可行性以及相关的前处理方法,通过一定前处理方法,减少土壤中杂质对测定的干扰和对色谱柱的污染.有效选取提取液的种类和浓度及提取时间,准确测定了土壤中Cl-和SO2-4含量.Cl-和SO2-4的相对标准偏差分别为2.70%、2.89%,检出限分别为0.1950、0.2230μg·mL-1,平均回收率分别为106.7%,95.8%.方法简便,快速、灵敏度高.     

Phase transitions and energy storage properties of some compositions in the (1−x)Li2SO4–xNa2SO4 system

In the binary system (1?x)Li₂SO₄–xNa₂SO₄, the solid–solid phase transitions and energy storage properties of Li₂SO₄, Na₂SO₄, the binary compound LiNaSO₄ and two eutectoids (E₁: 0.726Li₂SO₄–0.274Na₂SO₄; E₂: 0.03Li₂SO₄–0.97Na₂SO₄) were investigated by X-ray diffraction and differential scanning calorimetry. Li₂SO₄ has a solid–solid phase transition at 578 °C with the transition enthalpy 252 J g^?1. The binary compound LiNaSO₄ gives a slightly lower enthalpy value, 214 J g^?1 and its transition temperature is clearly reduced to 514 °C. The transition enthalpy of the eutectoid E₁ is maintained to 177 J g^?1 and its transition temperature is further reduced to 474 °C. Li₂SO₄, LiNaSO₄ and the eutectoid E₁ are applicable phase transition materials because of their large transition enthalpies. The enthalpies of Na₂SO₄ and the eutectoid E₂ are not very high (～45 J g^?1), but their transition temperatures are quite low (～250 °C); thus their transition properties may be applied at such low temperatures.     

CuCl2-FeCl3-H2SO4石墨插层化合物的结构特征

"采用水热法在150 ℃合成出了CuCl2-FeCl3-H2SO4的石墨插层化合物．通过X射线衍射、EDX、高分辨透射电子显微术分析了该石墨插层化合物的结构和成分．分析表明,CuCl2-FeCl3-H2SO4已经成功地插入到石墨的片层之间．测量了从5 K到300 K的磁化率随温度变化曲线,发现在低温时,该石墨插层化合物存在两个反铁磁转变,转变温度分别为50和100 K．"     

First-principles study on the electronic structure and optical properties of T12Cd2（SO4）3 and Rb2Cd2（SO4）3

With the help of ab initio full-potential linearized augmented plane wave （FPLAPW） method, calculating the electronic structure and linear optical properties is carried out for XCd2（SO4）3 （X =Tl, Rb）. The results show that Tl2Cd2（SO4）3 （TlCdS） has a larger band gap than Rb2Cd2（SO4）3 （RbCdS） and the energy bands for RbCdS are more dispersive than those of TlCdS. From their partial densities of states （PDOS）, we have observed that the hybridization between S ionic 2p and O atomic 2p orbitals forms SO4 ionic groups. The remarkable difference between RbCdS and TlCdS is, however, the degree of hybridization between cation （Tl and Rb） and its surrounding oxygen atoms. In the view of quantum chemistry, the strong p-d hybridization indicates the existence of their cation ionic bonds （Cd-O, Rb-O, and Tl-O）. The calculations of TlCdS and RbCdS show their optical properties to be less anisotropic. Their anisotropies in the optical properties mainly occur in a low photon energy region of 5-16 eV.     

Electrical conductivity and phase diagram of the Na2SO4CaSO4 system

Very high vacancy concentrations may be obtained in solid solutions of the high temperature phase of Na₂SO₄. In this paper the Na₂SO₄CaSO₄ system has been studied using differential scanning calorimetry (DSC), impedance spectroscopy and X-ray powder diffraction. The phase diagram, especially the stability range of the solid solution of the high temperature Na₂SO₄ phase, has been redetermined. The electrical conductivity of this solid solution increases rapidly with increasing CaSO₄ content and reaches a maximum for about 5 mol% CaSO₄; the conductivity at e.g. 300°C, 3.5×10⁻³ (μ cm)⁻¹, is almost three orders of magnitude higher than that of pure Na₂SO₄.     

SO2-4/CeO2-TiO2光催化材料的制备与光谱表征

采用溶胶-凝胶法结合硫酸浸渍法制备了SO2-4/CeO2-TiO2复合氧化物.利用X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)、吡啶吸附红外光谱(Py-FTIR)、紫外-可见光漫反射光谱(UV-Vis)、X射线光电子能谱价带谱(VB-XPS)及荧光光谱(PL)技术对样品的结构、性质进行了表征,以光催化分解水制氢为模型反应,评价了样品的光催化性能.XRD,FTIR结合PL结果表明CeO2与TiO2的复合形成了异质结构,有利于提高光生电子与光生空穴的分离效率,对催化剂活性的提高有促进作用;Py-FTIR谱图证明SO2-4/CeO2-TiO2复合氧化物在表面具有Lewis酸性,Lewis酸性位的产生是由于SO2-4在样品表面的配位吸附所致,S O— 的诱导效应增强了表面金属得电子能力,从而进一步提升光生载流子的分离效率;UV-Vis及XPS价带谱分析说明,半导体氧化物复合能够缩减带隙,拓宽光响应范围,Lewis酸性影响复合氧化物的能带结构,使其导带底位置向负向移动,利于光催化还原能力的提高,进而促进其光催化制氢活性.光催化分解水制氢实验结果表明,SO2-4/CeO2-TiO2复合氧化物具有优于纯氧化物CeO2,TiO2及未经硫酸浸渍的CeO2-TiO2复合氧化物的催化活性,5 h的产氢速率为1934.1μmol·g-1·h-1.光谱分析结果结合光催化制氢活性评价结果表明,SO2-4/CeO2-TiO2复合氧化物的异质结构与酸浸渍是影响样品光催化性能的主要因素.     

Ferroic phase transitions in β-LiNH4SO4

Abstract

The paper reviews the results of experimental and theoretical studies of ferroic phase transitions in β-LiNH₄SO₄ and its deuterated analogue. β-LiNH₄SO₄ undergoes succesive phase transitions: a paraelectric - ferroelectric phase transition at T₁ ? 462 K, a ferroelectric - ferroelastic phase transition at T₂ ? 283 K and a transition from one ferroelastic phase to the other at T₃ ? 28 K. Attention is focused on the influence of the order of phase transitions on the pattern of ferroelectric and ferroelastic domain structure, and also on the role played by the dynamics of molecular groups in the mechanism of transitions. The pre-transition effect connected with the ferroelectric-paraelectric transition: heterophase, capable of accounting for anomalies in different physical properties present 1-3 K below T₁ is shown. The anomalous temperature variation of spontaneous polarisation of the crystal is discussed within the framework of the phenomenological model of weak ferroelectrics.     

可见光响应SO2－4／Ce-TiO2的光谱特征及催化性能

采用溶胶‐凝胶法制备了Ce掺杂 T iO2,经 H2 SO4处理得到酸化Ce掺杂 T iO2。利用X射线衍射（XRD）、傅里叶变换红外光谱（FTIR）、吡啶吸附红外光谱（Py‐FTIR）、紫外‐可见光漫反射光谱（UV‐Vis）及X射线光电子能谱（XPS）技术对样品的性质进行了表征,以罗丹明B（RhB）在样品上的可见光催化降解为模型反应,评价了所制备样品的光催化性能。XRD测试结果表明,铈掺杂使 TiO2产生晶格缺陷、粒径减小,有利于光生电荷的转移,继而提高催化剂的活性;FTIR谱图说明SO2－4以桥式双齿配位吸附形式存在;Py‐FTIR谱图显示,酸化铈掺杂TiO2样品表面同时存在Br?nsted和Lewis酸位,但以Lewis酸为主。Lewis酸中心的缺电子性质有利于样品表面的光生电子与光生空穴分离,从而改善催化剂的活性;UV‐Vis结果表明,Ce掺杂减小了TiO2的带隙能,引入的杂能级能够捕获导带上的光生电子和价带上的光生空穴,降低光生电子‐空穴对的复合几率;同时还可以使能量较小的光子激发杂能级上捕获的电子,拓宽光响应范围;XPS分析表明SO2－4／Ce‐TiO2样品上同时存在Ce3＋／Ce4＋的混合价态,Ce3＋／Ce4＋氧化‐还原转换有助于TiO2受光激发后产生的光生电子和空穴的分离,从而提高光量子效率。酸化Ce掺杂TiO2对RhB的可见光催化降解反应有很好的活性,实验结果证明,H2 SO4酸化和Ce掺杂的协同作用改善了样品的可见光响应,促进了其可见光催化反应活性。     

SO2-4/TiO2固体酸的红外和拉曼光谱研究

用ＩＲ、Ｒａｍａｎ光谱研究了ＳＯ＾２－４／ＴｉＯ２固体酸在不同烧温度下的结构、晶相转变和表面酸中心。结果表明,ＳＯ＾２－４与ＴｉＯ２表面的结合为螯合式双配结构。当烧结温度小于５００℃时,ＳＯ＾２－４／ＴｉＯ２样品具有较高的结构稳定性,晶相结构以锐钛矿为主,表面Ｂ酸位数目约是Ｌ酸位数目的２倍,当烧结温度大于５００℃时,随着烧结晶度的升高,表面结合的ＳＯ＾２－４逐渐流失,晶相从锐钛矿转变为金红石,表面Ｂ酸位减少并消失。