Luminescence characteristics of K2Ca2(SO4)3:Eu,Tb micro- and nanocrystalline phosphor

K₂Ca₂(SO₄)₃ microcrystalline pure, doped with Eu, Tb and co-doped with Eu, Tb was prepared by solid-state diffusion method. Nanoparticles of these phosphors were also prepared by the chemical co-precipitation method. The formation of the compounds was confirmed by XRD. The particle size was calculated by broadening of the XRD peaks using Scherrer's formula. The particle size of nanocrystalline powder material was approximately found to be around 20 nm. Thermoluminescence and photoluminescence were studied to see the effect of co-doping and particle size. Tb³⁺ co-doping decreases the intensity in the Eu²⁺ doped phosphor due to the energy transfer and multiple de-excitations through various radiative and non-radiative processes. The sensitivity of K₂Ca₂(SO₄)₃:Eu,Tb microcrystalline phosphor was around 15 times more than LiF-TLD 100 and 7 times more than CaSO₄:Dy. A high temperature peak (615 K) was observed in case of the nanoparticles, which was attributed to a particle size induced phase transition. This was confirmed by differential scanning calormetry measurements. The decrease in the sensitivity in case of nanoparticles is attributed to the particle size effect i.e. volume to surface ratio. Theoretical analysis of the glow curves was done by glow curve convolution deconvolution method to calculate trapping parameters of various peaks.     

Effect of γ-radiation on TL,ESR and evaluation of trapping parameters of K2Ca(SO4)2:X (X = Dy or Eu) phosphors

ABSTRACT

The present phosphor K₂Ca(SO₄)_2, doped by dysprosium and europium, is synthesized by the solid-state diffusion method. The doping concentration varied from 0.1 to 0.5?mol% by weight. A phosphor is studied for X-ray powder diffraction, surface morphology analytical scanning electron microscopy and analyzed by energy-dispersive X-ray spectroscopy. The prepared phosphor K₂Ca(SO₄)_2, doped by Dy and Eu, has been characterized for thermoluminescence (TL) glow curve, showing maximum peak temperatures at 176°C and at 200°C, respectively. TL peak intensity of K₂Ca(SO₄)₂: Dy and Eu was compared with the standard TLD CaSO₄:Dy phosphor. Both phosphors show the dose linearity ranging from 20 to 240?Gy doses of γ-rays of ⁶⁰Co source at room temperature. Negligible fading has been observed when irradiated with γ-rays and stored for 60 days without taking any care from sunlight. The TL materials were used in powder forms. The linearity of ESR response with dose for powder forms of K₂Ca(SO₄)₂: Dy was also studied using the signals at g?=?2:0039 (SO₃^?) and at g?=?2:02282 (SO₄^?). It was observed that the range of linearity of dose response extended between 20 and 240?Gy. Kinetic parameters have been calculated using three different methods: Chen's peak shape method, various heating rate method and initial rise method. To study the heating rate method, the glow curve was recorded for the heating rate as 1°C, 3°C, 5°C, 7°C, 9°C each time. Electron spin resonance (ESR) shows the ionic radical formation during γ-irradiation, which is responsible for TL. The effect of temperature and microwave power on the ESR signal was also studied.     

Thermoluminescence of γ-irradiated BaCa(SO4)2:Eu,Dy

In this paper, thermoluminescence (TL) studies of BaCa(SO₄)₂:Eu,Dy phosphor are reported. A microcrystalline sample of BaCa(SO₄)₂:Eu,Dy was prepared by a solid state diffusion method and the formation of the compound was confirmed by the X-ray diffraction study. Morphology of the phosphor was analyzed by scanning electron microscopy (SEM). The sample is found to have an average particle size of 5?µm. TL glow curves of the γ-irradiated samples with different concentrations of Eu and Dy were studied and compared with BaCa(SO₄)₂:Eu and BaCa(SO₄)₂:Dy. It has been found that a single peak was located at around 230°C with the highest TL intensity in BaCa(SO₄)₂:Eu,Dy which is eight times and two times more than singly Dy- and Eu-doped BaCa(SO₄)₂ phosphor, respectively. For TL analysis, BaCa(SO₄)₂:Eu,Dy (0.2?mol%, 1?mol%) is annealed at different temperatures ranging from 900°C to 1100°C. Analysis of the TL glow curve was carried out by a glow curve deconvoluted method. Trapping parameters (activation energy and frequency factor) of all TL glow curves were evaluated by Chen's peak shape method. A comparison of trapping parameters between BaCa(SO₄)₂:Eu,Dy; BaCa(SO₄)₂:Eu and BaCa(SO₄)₂:Dy phosphors at 900°C, 1000°C and 1100°C is also reported in this paper.     

Photoluminescence and thermoluminescence characterization of Eu- and Dy -activated Ca3(PO4)2 phosphor

Rare-earth-doped polycrystalline Ca₃(PO₄)₂:Eu, Ca₃(PO₄)₂:Dy and Ca₃(PO₄)₂:Eu,Dy phosphors prepared by a modified solid-state synthesis has been studied for its X-ray diffraction, thermoluminescence (TL) and photoluminescence (PL) characteristics. The PL emission spectra of the phosphor suggest the presence of Eu³⁺ ion in Ca₃(PO₄)₂:Eu and Dy³⁺ ion in Ca₃(PO₄)₂:Dy lattice sites. The TL glow curve of the Ca₃(PO₄)₂:Eu compounds has a simple structure with a prominent peak at 228 °C, while Ca₃(PO₄)₂:Dy peaking at 146 and 230 °C. TL sensitivity of phosphors are compared with CaSO₄: Dy and found 1.52 and 1.20 times less in Ca₃(PO₄)₂:Eu and Ca₃(PO₄)₂:Dy phosphors, respectively. The Ca₃(PO₄)₂:Eu,Dy phosphors shows switching behavior under two different excitation wavelengths and enhancement in PL intensity of Dy³⁺ ions were reported. The paper discusses the photoluminescence and thermoluminescence behavior of Eu³⁺ and Dy³⁺ ion in Ca₃(PO₄)₂ hosts, it may be applicable to solid-state lighting as well as thermoluminescence dosimetry applications.     

Solid state metathesis of CaSO4:Eu2+ phosphor

CaSO₄:Dy, is a well known phosphor for radiation dosimetry using thermoluminescence. CaSO₄:Eu³⁺ and CaSO₄:Eu²⁺ phosphors also find applications in radio-photoluminescence dosimetry and photoluminescent liquid crystal displays (PLLCD), respectively. Various syntheses of these phosphors are known. In this paper solid state metathesis of CaSO₄:Eu using domestic microwave oven is described for the first time. The synthesis is fast, the entire process being completed within few minutes. The phosphor is characterized using XRD and PL techniques.     

Luminescence of KCaSO4Cl:X, Y (X=Eu or Ce; Y=Dy or Mn) halosulfate material

Polycrystalline KCaSO₄Cl:Eu, Dy, KCaSO₄Cl:Ce, Dy and KCaSO₄Cl:Ce, Mn phosphors prepared by a solid state diffusion method have been studied for its photoluminescence (PL) characteristics. The presence of two overlapping bands at around 400 and 450 nm in the PL emission spectra of the phosphor suggests the presence of Eu²⁺ in the host compound occupying two different lattice sites. The effects of co-doping on the photoluminescence (PL) characteristics of KCaSO₄Cl:Eu or Ce phosphors have been studied. The decrease in peak intensity of the phosphor on co-doping it with Dy gives an insight into the emission mechanism of the phosphors, which involves energy transfer from Eu²⁺→Dy³⁺, Ce³⁺→Dy³⁺ and Ce³⁺→Mn²⁺.     

Thermally stimulated luminescence of Ca3(PO4)2 and Ca9Ln(PO4)7 (Ln = Pr,Eu, Tb,Dy, Ho,Er, Lu)

The series of whitlockite compounds Ca₃(PO₄)₂ and Ca₉Ln(PO₄)₇ (Ln = Pr, Eu, Tb, Dy, Ho, Er, Lu) was studied in radioluminescence (RL) and thermally stimulated luminescence (TSL) excited by X-rays. f-f emission lines of Ln³⁺ were observed in RL for Ca₉Ln(PO₄)₇ (Ln = Pr, Eu, Tb, Dy, Ho, Er) whereas d-d emission band of the impurity Mn²⁺ was observed in Mn:Ca₃(PO₄)₂ and Mn:Ca₉Lu(PO₄)₇ at 655 nm. In TSL, the Eu, Ho and Er compounds did not show any signal. As Eu³⁺, Ho³⁺ and Er³⁺ present the highest Ln³⁺/Ln⁴⁺ ionization potential (IP) of the series, this was interpreted as the inability of these lanthanides to trap a hole. On the contrary Pr³⁺ in Ca₉Pr(PO₄)₇, Tb³⁺ in Ca₉Tb(PO₄)₇, Dy³⁺ in Ca₉Dy(PO₄)₇, Mn²⁺ in Mn:Ca₃(PO₄)₂ and Mn:Ca₉Lu(PO₄)₇ were identified as hole traps and radiative recombination centers in the TSL mechanism. Ca₉Tb(PO₄)₇ was found to be a high intensity green persistent phosphor whereas Mn:Ca₉Lu(PO₄)₇ is a red persistent phosphor suitable for in vivo imaging application.     

Eu and Ce emission in sulphate based phosphors

Polycrystalline KMgSO₄Cl:Eu and Na₅(PO₄)SO₄:Ce phosphors prepared by a wet chemical method have been studied for its photoluminescence (PL) and thermoluminescence (TL) characteristics. The TL glow curve of the compound has a prominent peak at 200 °C and may be useful for TL study. TL sensitivity of the KMgSO₄Cl:Eu phosphor is found to be 1.7 times less than that of TLD—CaSO₄:Dy. The presence of bands at around 420, 435 and 445 nm in the PL emission spectra of the phosphor suggests the presence of Eu²⁺ in the host compound. Moreover a TL glow curve of the Na₅(PO₄)SO₄:Ce gives a better understanding of the TL mechanism (peaks at 271 and 310 °C) involved in the concerned phosphor. The PL emission spectra are observed at 382 nm for the various concentrations. In this paper we report PL and TL characteristics of KMgSO₄Cl:Eu halosulphate and Na₅(PO₄)SO₄:Ce phosphate sulphate phosphors first time.     

Thermoluminescent analysis of CaSO4:Tb,Eu crystal powder for dosimetric purposes

The motivation of this work was to produce crystals of CaSO₄ doped with an unusual combination of RE elements such as terbium (Tb) and europium (Eu) in different concentrations, and analyze its thermoluminescent (TL) properties. The crystals were produced by the slow evaporation route using calcium carbonate (CaCO₃) as precursor, and incorporating the dopants (Tb₂O₃ and Eu₂O₃) in a solution of sulfuric acid, that is evaporated and collected again, leaving just CaSO₄:Tb,Eu crystal powder. The terbium and europium ions were incorporated in concentration ratios of 1:1, 2:1 and 5:1 (weight proportions). X-ray diffraction analyses showed that samples of doped CaSO₄ exhibit only a single phase corresponding to the crystal structure of anhydrite. The radioluminescence confirmed the presence of Tb³⁺ and Eu²⁺ in the crystal matrix. The CaSO₄:Tb,Eu crystal powders showed TL emission glow curves with three peaks centered around 170 °C, 270 °C and 340 °C, after irradiation with a ⁹⁰Sr/⁹⁰Y source. Thermoluminescent (TL) characteristics such as linearity, reproducibility and fading were evaluated. Samples produced with concentration ratio of 2:1 of Tb and Eu showed the highest TL intensity. The produced CaSO₄:Tb,Eu samples present TL properties useful for dosimetric purposes.     

Energy transfer process in CaSO4:Tb,Ce phosphor

Thermoluminescence (TL) and photoluminescence studies have been carried out on CaSO₄:Tb, CaSO₄:Ce and CaSO₄:Tb,Ce phosphors with the aim of studying energy transfer process in the CaSO₄:Tb,Ce phosphor. CaSO₄:Tb,Ce shows TL peaks at 150, 220, 320 and 400°C. Changes in Tb and Ce concentrations influence the relative heights of these glow peaks. Co-doping with 0.1 mol% of Ce in CaSO₄:Tb enhances the sensitivity of 320^oC TL peak by a factor of 15. Fluorescence results show that there is energy transfer from Ce to Tb ion. The defect centres formed in CaSO₄:Tb,Ce phosphor are studied using electron spin resonance technique. The 320^oC glow peak correlates with a centre (SO₃⁻radical) with g-values: g_||=2.0061 and g_⊥=2.0026.     

Quantum Effect on the Energy Levels of Eu2+ Doped K2Ca2(SO4)3 Nanoparticles

Quantum confinement effect on the energy levels of Eu²⁺ doped K₂Ca₂(SO₄)₃ nanoparticles has been observed. The broad photoluminescence (PL) emission band of Eu²⁺ doped K₂Ca₂(SO₄)₃ microcrystalline sample observed at ～436 nm is found to split into two narrow well resolved bands, located at 422 and 445 nm in the nanostructure form of this material. This has been attributed to the reduction in the crystal field strength of the nanomaterials, which results in widening the energy band gap and splitting the broad 4f⁶5d energy level of Eu²⁺. Energy band gap values of the micro and nanocrystalline K₂Ca₂(SO₄)₃ samples were also determined by measuring the UV–visible absorption spectra. These values are 3.34 and 3.44 eV for the micro and nanocrystalline samples, respectively. These remarkable results suggest that activators having wide emission bands might be subjected to weak crystal strength via nanostructure materials to modify their electronic transitions. This might prove a powerful technique for producing new-advanced materials for use in the fields of solid state lasers and optoelectronic devises.     

Rare earth doped lithium titanate (Li2TiO3) for potential phosphor applications

Lithium titanate ceramics doped with three rare earth (RE) ions namely Eu³⁺, Dy³⁺ and Tb³⁺ were synthesized and their photoluminescence (PL) properties were investigated. PL spectra of Eu doped sample showed peaks corresponding to the ⁵D₀→⁷F_j (j=0, 1, 2, 3 and 4) transitions under 230 nm excitation. Strong red emission coming from the hypersensitive ⁵D₀→⁷F₂ transition of Eu³⁺ ion suggested the presence of the dopant ion in a highly asymmetric environment. Dy doped samples showed the Dy³⁺ emission characteristic due to ⁴F_9/2→⁶H_15/2 and ⁴F_9/2→⁶H_13/2 transitions. Their relative intensity ratios also suggested the presence of asymmetric environment around the metal ion. In case of the Tb³⁺ doped sample blue-green emission corresponding to the ⁵D₄→⁷F_j (j=6, 5 and 4) transitions was seen. The fluorescence lifetimes of Eu³⁺, Dy³⁺ and Tb³⁺ ions were found to be 645, 900 and 740 μs, respectively. PL intensity of the individual rare earth doped samples was compared with commercial red and green phosphors. It was found that the emission from Eu doped titanate sample was 46% of the commercial red phosphor and in case of the Tb samples it was 30% when excited at 230 nm. However, the synthesized Eu doped titanate sample showed better color purity as compared to the commercial phosphor. The titanate host was doped with all the three rare earths to get white light emission from the system. The individual rare earth ion content was optimized so as to get a near white light emission. The color coordinates of the triple doped systems were evaluated and plotted on the CIE x–y diagram. Our results suggest that lithium titanate has enough potential to be a phosphor material.     

Photoluminescence of Eu single doped and Eu/Dy codoped Sr2Al2SiO7 phosphors with long persistence

This paper reports the preparation of long persistent Sr₂Al₂SiO₇:Eu²⁺ and Sr₂Al₂SiO₇:Eu²⁺, Dy³⁺ phosphors and the comparison of their photoluminescent properties. The silicate phosphors prepared by solid-state reaction routine showed a broad blue emission peaking at 484 nm when activated by UV illumination. Such a bluish-green emission can be attributed to the intrinsic 4f-5d transitions of Eu²⁺. After the UV source was switched off, long persistent phosphorescence could be observed by naked eyes for both samples in darkness. Afterglow measurements revealed that Eu/Dy codoped phosphor possesses better afterglow properties than the Eu single doped one, since the maximum lifetime (τ_max=99 s) of the photons calculated from the decay profile is much larger than that of the Eu single doped phosphor (τ_max=82 s). TSL results suggested that the difference in afterglow properties was caused by the difference in the electron traps within the crystal lattice. For Eu/Dy codoped phosphor, the doping of Dy ions produced electron traps with trap depth of 0.52 eV, which is suitable and therefore leads to good persistence. However, in the case of Eu single doped phosphor, the trap depth is 0.88 eV, which is really too deep an energy barrier to overcome, and therefore a poor persistence was observed in the experiment.     

Feasibility study of CaSO4:Eu,CaSO4:Eu,Ag and CaSO4:Eu,Ag(NP) as thermoluminescent dosimeters

This work evaluates the dosimetric properties of crystals of CaSO₄ doped with unusual elements, such as europium (Eu) and silver (Ag), including their nanoparticle forms, after the incorporation of glass or Teflon and compares them with well-known thermoluminescent dosimeters (TLD). X-ray diffraction analyses showed that samples of doped CaSO₄ exhibit only a single phase corresponding to the crystal structure of anhydrite. Optical spectroscopy confirmed the presence of Eu³⁺ in the crystal matrix and a luminescent gain due the presence of silver nanoparticles. The composites showed thermoluminescent emission glow curves, with a single peak centered at approximately 200 °C for pellets with Teflon and at 230 °C for pellets with glass. The dosimeters based on calcium sulfate doped with europium and silver nanoparticles provided the most intense thermoluminescent (TL) emission of the composites studied. In comparison with commercial TLD, such as LiF:Mg,Ti and CaSO₄:Dy, the CaSO₄:Eu,Ag(NP)+glass produced in this work presented similar low detection limits and higher sensitivity. The new methods for the preparation of dosimeters and the incorporation of glass are shown to be viable because all of the samples presented a linear, reproducible and first order kinetic TL emission.     

UV-induced photoluminescence and thermally stimulated luminescence of CaSO4:Eu and CaF2:Tb3+ phosphors

Ultraviolet radiation induced changes in photoluminescence (PL) and thermally stimulated luminescence (TSL) of europium activated calcium sulphate (CaSO₄:Eu³⁺, Eu²⁺) and terbium doped calcium fluoride (CaF₂:Tb³⁺) phosphors have been studied. PL measurements suggest conversion of Eu³⁺ to Eu²⁺ on 254 nm irradiation corresponding to charge transfer band of Eu³⁺ ions and reduction of Eu²⁺ ions with 365 nm illumination representing a f–d transition of Eu²⁺ ions. Similar studies carried out on CaF₂:Tb³⁺ phosphor, however, do not show any significant wavelength specific changes. The integrated TSL output appears to be rate-dependent for both phosphors. The wavelength dependent changes in TSL output observed for CaSO₄:Eu phosphor have been correlated with those obtained in PL studies. The changes in TSL and PL characteristics of CaF₂:Tb³⁺ phosphor have been explained on the basis of stabilisation of traps based on matrix specific charge similarities.     

Luminescence characteristics of Dy3+ activated Na 2Sr 2Mg (BO 3)2F 2: Dy 3+ phosphor

In this paper, we have reported a new Na ₂Sr ₂Mg (BO ₃)₂F ₂:Dy ³⁺ thermoluminescence (TL) phosphor prepared via the wet chemical method. Prepared phosphor was characterized by X-ray powder diffraction, photoluminescence (PL), TL and scanning electronmicroscopy techniques. The scanning electronmicroscopic image of Na ₂Sr ₂Mg (BO ₃)₂F ₂:Dy ³⁺ phosphor confirms the micron size of particles. Under the PL study, the characteristic emission spectrum of Dy ³⁺ corresponding to ⁴F _9/2→⁶H _15/2 (481 nm) and ⁴F _9/2→⁶H _13/2 (576 nm) transitions was observed. The TL property of the as prepared phosphor was also found to be good. TL intensity of Na ₂Sr₂Mg(BO ₃)F ₂:Dy ³⁺ phosphors at 0.99 kGy exposure of γ-irradiations was compared with standard CaSO ₄:Dy phosphor. It was seen that TL intensity of Na ₂Sr ₂Mg (BO ₃)₂F ₂: Dy ³⁺ phosphors is 1.1 times less compared with the standard CaSO ₄:Dy TL dosimeter phosphor. The kinetic parameters are also discussed in detail. The values of activation energy E (eV) and frequency factor S (s ^?1) were found to be 0.57 eV and 1.25×10⁶ s^?1, respectively.     

Preparation and TSL studies in Tb activated LiMgPO4 phosphor

LiMgPO₄:Tb³⁺ phosphor was synthesized by solid state reaction. The thermally stimulated luminescence (TSL) glow curve of Tb doped LiMgPO₄ exhibits a main TSL peak at 170 °C with shoulders at 100 and 260 °C on either side of this peak. The TSL sensitivity of the phosphor was found to be about 2.5 times that of CaSO₄:Dy phosphor. TSL emission and photoluminescence (PL) studies show that Tb³⁺ ion acts as luminescence centre in this phosphor. The kinetic parameters, namely activation energy (E) and frequency factor (s) associated with the main glow peak have been determined using peak shape method. The activation energy and frequency factor obtained are 1.35 ± 0.03 eV and (6.53 ± 0.43) × 10¹⁴ s^?1 respectively. The paper discusses the dosimetric characteristics like dose response, fading, energy response and minimum detectable dose and results thereof.     

Optically stimulated luminescence in doped K3Na(SO4)2 phosphors

Optically stimulated luminescence (OSL) in Cu and Eu doped K₃Na(SO₄)₂ is reported for the first time. The Cu-doped sample shows OSL sensitivity which gets enhanced by co-doping with Mg²⁺ ions. The Cu-doped and quenched sample shows better sensitivity which is almost double than that of the slowly cooled sample, whereas the sensitivity of Mg co-doped sample remains nearly same irrespective of the thermal treatment. The Cu-doped sample shows TL peak around 200 °C and moderate OSL sensitivity. Doping of Mg shifts the TL peak to around 160 °C and is correlated with good OSL sensitivity. Eu-doped sample does not show OSL sensitivity. However, relatively good OSL sensitivity is observed in Aluminium co-doped and slowly cooled sample, which is about 15% of the commercial Al₂O₃:C(Landuer Inc.). A near fully optically sensitive TL peak around 155 °C is observed. The dose response is linear and practically no OSL fading is observed in first five days of storage in slowly cooled sample. This study on conventional sulphate-based TL phosphors will be useful in developing OSL phosphors for radiation dosimetry.     

Luminescence investigations on sulfate apatite Na6(SO4)2FCl:RE (RE=Dy, Ce or Eu) phosphors

A new phosphor in the Cl-F system doped with Dy, Ce and Eu has been reported. Characterization of this phosphor using XRD, PL and TL techniques is described. Polycrystalline Na₆(SO₄)₂FCl:Dy; Na₆(SO₄)₂FCl:Ce and Na₆(SO₄)₂FCl:Eu phosphors prepared by a solid state diffusion method have been studied for their X-ray diffraction, photoluminescence (PL) and thermoluminescence (TL)characteristics. The PL excitation and emission spectra of phosphors were obtained. Dy³⁺ emission in the host at 475 and 570 nm is observed due to ⁴F_9/2→⁶H_15/2 and ⁴F_9/2→⁶H_13/2 transition, respectively, whereas the PL emission spectra of Na₆(SO₄)₂FCl:Ce phosphor shows the Ce³⁺ emission at 322 nm due to 5d→4f transition of Ce³⁺ ion. In Na₆(SO₄)₂FCl:Eu lattice, Eu²⁺ as well as Eu³⁺ emissions are observed. The emission of europium ion in this compound exhibits the blue as well as red emission. The TL glow curves of the same compounds have the simple structure with a prominent peak at 150, 175 and 200 °C. TL response, fading, reusability and trapping parameters of the phosphors are also studied. The TL glow curves of γ-irradiated Na₆(SO₄)₂FCl sample show one glow peak indicating that only one set of traps is being activated within the particular temperature range each with its own value of activation energy (E) and frequency factor (s). The trapping parameters associated with the prominent glow peak are calculated using Chen’s half width method. The release of hole/electron from defect centers at the characteristic trap site initiates the luminescence process in these materials. The intensity of the TL glow peaks increases with increase of the added γ-ray dose to the samples.     

Thermoluminescence of rare earth activated CdSO4, SrSO4 and BaSO4

The thermoluminescence (TL) of rare earth (RE) activated sulfates of Cd, Sr and Ba was studied above room temperature. Many of the phosphors prepared exhibit an extremely bright TL following X-irradiation (most notably with Sm, Eu, Tb, Dy and Tm dopants), having an efficiency comparable to that of the highest sensitivity phosphors available for TL dosimetry, and exhibiting activator-induced glow peaks between 405 and 480°K. In a given lattice, the RE³⁺ ions produce a characteristic glow peak at the same temperature (independent of the particular RE ion), whereas Eu²⁺ produces a single glow peak at a different temperature. A decrease in glow peak temperature with increasing interatomic spacing was observed in the homologous SrSO₄-BaSO₄ system - this shift being most pronounced in the Eu²⁺ -doped materials. TL emission spectra were obtained for trivalent Sm, Tb, Dy and Tm and for divalent Eu in these sulfates (and also in CaSO₄).