X射线散射对面密度测量结果影响的数值模拟研究

定性分析了X射线散射对面密度测量结果的影响,给出了面密度测量结果偏差的评估表达式。利用蒙特卡罗方法数值模拟了不同照相布局、不同光源能量和不同材料类型情形下X射线散射对测量结果的影响。模拟结果表明：在无防护窗情形下,被测物自身散射将导致测量结果偏小;在有防护窗情形下,前窗散射对测量结果的影响不大,后窗散射对测量结果的影响与接收介质离被测物的距离有关,具体表现为距离越小影响越大;在一定光子能量范围内,光源能量越低散射导致的测量偏差越大;被测物的原子序数和密度越大,散射导致的测量偏差越大。     

轴流式喷水推进器泵级内部流场的数值计算

采用数值计算的方法,研究了轴流喷水推进器泵级模型的内部三维紊流流场和性能。计算针对泵级的进口到喷水推进器的出口进行,包括进水区域、叶轮、导流壳区域的泵级整个流道。采用结构网格对计算区域进行剖分,应用NUMECA软件对控制方程进行求解。选用Spalart-Allmaras一方程紊流模型,使用时间推进法计算流场中的流动参数。并根据流场计算结果对泵级的流量-扬程特性和流量-效率特性进行了预测。计算与实验结果对比表明,二者取得了较好的一致,说明采用的计算方法具有较好的可信性及较高的计算精度。根据流场计算结果,对泵级的性能进行了分析。     

基于二代curvelet变换的图像融合研究

曲波(Curvelet)作为一种新的多尺度分析方法比小波更加适合分析二维图像中的曲线或直线状边缘特征,而且具有更高的逼近精度和更好的稀疏表达能力.将curvelet变换引入图像融合,能够更好地提取原始图像的特征,为融合图像提供更多的信息.第二代curvelet理论的提出也使得其理论更易理解和实现.因此,提出了一种基于第二代curvelet变换的图像融合方法,首先将图像进行curvelet变换,然后在相应尺度上利用融合规则将curvelet系数融合,最后进行重构得到融合结果.对多聚焦图像进行了实验,采用均方误差、偏差指数和相关系数对融合结果进行了客观评价,并与基于小波变换的融合进行了比较,实验结果表明该方法除分解2层时与小波性能相当,取其他分解层数时均获得更好的融合效果.     

X射线散射对面密度测量结果影响的数值模拟研究

定性分析了X射线散射对面密度测量结果的影响,给出了面密度测量结果偏差的评估表达式。利用蒙特卡罗方法数值模拟了不同照相布局、不同光源能量和不同材料类型情形下X射线散射对测量结果的影响。模拟结果表明:在无防护窗情形下,被测物自身散射将导致测量结果偏小;在有防护窗情形下,前窗散射对测量结果的影响不大,后窗散射对测量结果的影响与接收介质离被测物的距离有关,具体表现为距离越小影响越大;在一定光子能量范围内,光源能量越低散射导致的测量偏差越大;被测物的原子序数和密度越大,散射导致的测量偏差越大。     

Impact on short length bars

A finite element method for the solution of an axisymmetric wave propagation problem of a bar of finite length is proposed. The results are obtained for a uniform bar with (i) a displacement input and (ii) a stress input. Also results are obtained for a discontinuous bar with stress input. They are compared with the existing finite difference solutions and experimental results. It is observed that the results are in close agreement. The study is then extended to the case of bars with an hemispherical end. The advantage of using the finite element method for such problems is indicated. Finally the results for a composite bar comprising a hallow cylinder and hemisphere are obtained by using the finite element method. Experiments are conducted to verify these results.     

显微栅线投影法用于微镜转角测量

采用显微栅线投影法结合相移技术测量了微镜在不同驱动电压下的转角,并同理论值进行了比较,平均误差为4.5%,结果表明:测量值和理论值比较吻合.     

水位骤变时的饱和-不饱和渗流数值计算

本文应用全隐式交替方向迭代法对水位骤变时的饱和-不饱和渗流问题求出了数值解。对于赤井模型,计算结果与实验结果十分接近,比有限元法的计算结果好。对于大尺度的驹田蓄水池模型,计算结果与有限元法的结果基本一致。     

Melting of xenon monolayers - computer simulations

The results of Monte Carlo simulations of xenon monolayers deposited on graphite are presented. Systems of various surface densities and in a wide range of temperatures are investigated. The results are compared to the experimental data and to the previous results for nitrogen. The results of simulations are in good agreement with the experimental ones and confirm that melting in two dimensions is vacancy-driven. Typical real-space configurations of Xe atoms and calculated specific heat results are shown.     

耦合带状线定向耦合器大功率合成器的设计

介绍了直线加速器高频全固态功率源中大功率合成器件-3 dB定向耦合器的理论计算和工程设计过程, 该合成器工作频率80.5 MHz, 输出连续波功率大于20 kW。 分析了合成器的功率容量, 并对相应的理论计算结果、 CST (Computer Simulation Technology)软件模拟计算结果和实际功率合成器件测量结果进行了比较。 通过比较得出, CST仿真结果与测试结果基本一致, 隔离度和电压驻波比等实测指标优于设计指标, 只有耦合度与设计指标有些偏差, 总体上达到了预期的设计要求。 在输出功率20 kW时, 取样波形无失真, 合成器无明显温升, 满足固态功率源大功率稳定运行的要求。 The principle of design and calculation of the power synthesis in the solid state amplifier are described in this paper. The working frequency of the synthesizer is 80.5 MHz. The output continuous wave power is more than 20 kW; The synthesizer power capacity is analyzed. The theoretical calculation results, Computer Simulation Technology (CST) simulated results are compared with the measured results of the actual 3 dB couplers. The analysis of the measured results and CST calculated results shows that the simulation is in agreement with the measurement results which meet the design requirements of the solid state amplifier. Except the coupling coefficient, the isolation, the VSWR and other parameters are better than the design target. When the output power is 20 kW, the sampling waveform has no deform and the temperature of the synthesizer is stable.     

Analysis of collimated radiation in participating media using the discrete transfer method

A general formulation of the discrete transfer method is provided to analyze radiative heat transfer problems in a participating medium subjected to collimated radiation. The formulation is validated by considering 1-D planar absorbing, emitting and anisotropically scattering gray medium in radiative equilibrium. Anisotropy of the medium is approximated by linear anisotropic phase function. For the purpose of comparison, the problem is also solved analytically. Results are obtained for different angles of incidence of the collimated radiation. At a given angle of incidence, results are obtained for forward, isotropic and backward scattering situations. Heat flux results are compared over a wide range of values of the extinction coefficient. Emissive power distributions in the medium are also obtained for some cases. The discrete transfer method results are found to compare very well with the analytic results.     

LO-phonon effect on the exciton binding energy in polar rectangular quantum wires

Longitudinal optical phonon effect on Wannier excitons in polar rectangular quantum wires is studied by a variational approach. The binding energy is calculated and the numerical results for several II-VI and III-V compound semiconductor rectangular quantum wires are given. The results show that the phonon effect reduces the binding energy and cannot be neglected. The phonon contribution to the binding energy is sensitive to the size of the rectangular quantum wire section, and increases with decreasing section area. The results for the GaAs rectangular quantum wires coincide with the experimental results. The calculated binding energy and the phonon effect in II-VI QWWs are both stronger than those in III-V compound systems, and the results for ZnSe QWW are qualitatively in agreement with the experiments.     

一种连续相位板焦斑边缘轮廓的提取方法

为了获得连续相位板（CPP）焦斑的外形尺寸,提出一种焦斑边缘轮廓的提取方法。连续相位板焦斑图像内部梯度起伏较大,直接应用传统边缘检测方法,易形成内部伪边缘。通过对焦斑图像依次作梯度处理、阈值分割、空间扫描和椭圆拟合,可以有效地获取焦斑边缘轮廓。比较了分别采用Laplace, Sobel, Krisch, Log算子进行梯度处理的提取结果,结果表明：采用Krisch算子,焦斑边缘轮廓提取的结果更稳定可靠。比较了阈值分割时不同阈值情况下的提取结果,表明阈值选取在背景梯度均值的110倍至180倍时,焦斑边缘轮廓提取结果比较可靠。     

The self-trapping of hydrogen in semiconductors

Recent theoretical calculations are discussed which show that the minimum energy site for hydrogen in silicon is the bond-centered site, while a secondary minimum is at the anti-bonding site, it is noted that these results are strongly dependent on the relaxation experienced by the silicon atoms neighboring the hydrogen. Several experimental results are discussed, namely, the observed model of the hydrogen-passivated acceptor, etching of the silicon surface by hydrogen, the exponential depth dependence of the near-surface hydrogen diffusion profile, and related muonium results, and from these results it is argued that, in some instances at least, the BC-site is the lowest energy site for hydrogen.     

钬铝石榴石晶场参数调整

利用比热实验值,对钬铝石榴石（Ho3Al5O12）晶体的晶场参数进行了调整,依此计算了Ho3Al5O12晶体的晶场能谱、Zeeman劈裂能级和波函数. 在外磁场H=0时,分别计算了Ho3Al5O12晶体的总比热、总熵随温度的变化,以及外磁场H=10kOe时该晶体倒数磁化率的温度关系,理论计算结果均与已有实验数据符合较好.该工作为进一步探究该晶体的其它性质奠定了必要的理论基础,对实际生产和科学研究中磁制冷材料的优化选取也具有一定的现实意义.     

反射镜架系统运动学支撑连接的有限元建模

根据反射镜架系统中运动学支撑连接的物理接触形式,采用相应的位移协调方式来模拟其连接,建立了一个镜架结构的有限元模型,并分析了该镜架系统的模态及结构在地脉动载荷下的微振动分析。得到前三阶模态固有频率的最大误差小于5%,各测点的位移响应均方根的计算值与试验值吻合较好,多数点位移均方根误差控制在30%以内,且各支撑连接部位的传递特性的计算结果与试验结果比较一致,验证了所采用的运动学支撑连接的建模方法的可行性。     

反射镜架系统运动学支撑连接的有限元建模

 根据反射镜架系统中运动学支撑连接的物理接触形式,采用相应的位移协调方式来模拟其连接,建立了一个镜架结构的有限元模型,并分析了该镜架系统的模态及结构在地脉动载荷下的微振动分析。得到前三阶模态固有频率的最大误差小于5%,各测点的位移响应均方根的计算值与试验值吻合较好,多数点位移均方根误差控制在30%以内,且各支撑连接部位的传递特性的计算结果与试验结果比较一致,验证了所采用的运动学支撑连接的建模方法的可行性。     

真空绝缘堆均压环的结构优化

采用数值模拟法和有限元网格细化法对比给出电场的合理参考范围,分别选取距离阴极三结合点(0.005)(21/2d)处(d是绝缘体的厚度)和距离阳极三结合点(0.008 5)(21/2d)处的电场强度为参考点。通过优化均压环形状,采用阴极激发闪络和阳极激发闪络两种模型来控制三结合点处的场强,优化得出阴极三结合点处场强值为2.55 kV/mm,阳极三结合点处场强值为23 kV/mm。     

激光聚变中受激布里渊散射的混合模拟研究

在激光等离子体相互作用中, 受激布里渊散射的模拟耗时较长. 为缩短模拟时间, 对电子采用Boltzmann描述, 开发了一维混合Vlasov程序, 利用离子束双流不稳定性理论结果对程序进行了考核.在此基础上对激光聚变中的受激布里渊散射进行了研究, 结果表明程序正确, 模拟结果可信.     

Pulse compression in dispersion-decreasing-like fibers

Pulse compression characteristics in dispersion-decreasing-like fibers (DDLF) are firstly investigated by employing the second-harmonic generation frequency-resolved optical gating (SHG-FROG) technique, are compared with the numerical results that are obtained using the split-step Fourier method. It is found that the experimental data are consistent with the numerical results. The results show that the pulse compression method is effective. The pulse can be effectively compressed and its spectrum can be broadened in the DDLF. That the pulse compression effect is enhanced with the increase of the input power is in correspondence with the spectrum broadening.     

介观尺度流体绕流球体的耗散粒子动力学模拟

采用耗散粒子动力学(dissipative particle dynamics, DPD)方法, 对两平行平板间流体绕流三维球体进行了计算. 球体和平行平板由达到平衡状态的冻结DPD粒子组成, 流体在不同无量纲外力驱动下流动, 球体受力由组成球体的所有冻结DPD粒子求和得到. 流动达到充分发展后, 输出球体在流动方向的受力, 并计算球体的阻力系数, 与文献中的关联式进行了对比. 结果表明, 在Re≤qslant 100的范围内, DPD方法能较准确地计算出阻力系数, 在较大雷诺数时, 由于流体的压缩性导致计算结果出现差异.