Magnetic and structural properties of magnetoresistive FexAu100−x alloys produced by mechanical alloying

Fe_xAu_100−x alloys have been produced for the first time by mechanical alloying. X-ray diffractograms show FCC peaks. From the X-ray diffracion peak-widths we estimate the final grain size, which vary with x from 112 nm (for x=15) to 32 nm (for x=30). Lattice parameter decreases with concentration (minimum 0.401 nm at x=30), but above Vegard's law values. Susceptibility measurements show cluster-glass behaviour. Critical temperatures are consistently lower than similar alloys produced by arc melting followed by fast quenching. A magnetic phase diagram is presented. Giant magnetoresistance is present in all samples, with a maximum at x=25. This effect is caused by the dispersion of small iron clusters produced by the mechanical work.     

Interactive effect of impurities on giant magnetoresistance of Co–Fe/Cu multilayers

Giant magnetoresistance of Co–Fe–B/Cu multilayers fabricated in the sputtering atmosphere, where the amount of oxygen impurity is varied, is discussed in connection with their interfacial roughness. The magnetoresistance (MR) ratio of Co–Fe/Cu multilayers is enhanced by up to 33% when the oxygen content is varied between 10 and 100 ppm of processing Ar gas. The enhancement of the MR ratio was due to the flattening effect of impurity oxygen on the multilayer interfaces: the root mean square roughness of the multilayer was decreased from 7.5 to 5 Å. With increasing boron content in Co–Fe layers, however, the enhancing effect of MR ratio by oxygen diminished and nearly vanished for 12 at%-B–(Co–Fe) case. The strong affinity of boron for oxygen is suggested as a probable mechanism.     

Current-perpendicular (CPP) magnetoresistance in magnetic metallic multilayers

We present an experimentalist's view of the theory and published data for the magnetoresistance (MR) of a multilayer composed of alternating ferromagnetic (F) and non-magnetic (N) metals measured with current flow perpendicular to the layer planes (CPP-MR). We explain the advantages of this geometry for determining the fundamental quantities underlying spin-polarized transport, describe the different techniques developed to measure the CPP-MR, summarize the salient features of the models used to analyze experimental data, and describe tests of those models. We then review what has been learned so far about spin-dependent scattering anisotropy and spin relaxation in F-metals and at F/N interfaces, specific resistances of F/N interfaces, the temperature dependence of spin-polarized transport parameters, and mixing of the spin-polarized electron currents. After a brief overview of some new directions, we conclude with a list of questions still to be answered.     

Influence of domain wall density on interlayer coupling in CoFe/Au/Co/Au multilayers

We measure magnetization reversal and giant magnetoresistance of CoFe/Au/Co/Au multilayers and use micromagnetic simulations to model them. We characterize the system by perpendicular and easy-plane effective anisotropy of Co and CoFe layers, respectively. We show that minor hystereses of magnetoresistance can be reasonably well described by the model. The simulations show that the variation of resistance with the field depends on the field strength at which the sweep reverses, and is correlated with the number of stripe domains present in the Co layers.     

Perpendicular-current studies of electron transport across metal/metal interfaces

We review what we have learned about the scattering of electrons by the interfaces between two different metals (M1/M2) in the current-perpendicular-to-plane (CPP) geometry. In this geometry, the intrinsic quantity is the specific resistance, AR, the product of the area through which the CPP current flows times the CPP resistance. We describe results for both non-magnetic/non-magnetic (N1/N2) and ferromagnetic/non-magnetic (F/N) pairs. We focus especially upon cases where M1/M2 are lattice matched (i.e., have the same crystal structure and the same lattice parameters to within ∼1%), because in these cases no-free-parameter calculations of 2AR agree surprisingly well with measured values. But we also list and briefly discuss cases where M1/M2 are not lattice matched, either having different crystal structures, or lattice parameters that differ by several percent. The published calculations of 2AR in these latter cases do not agree so well with measured values.     

Giant magnetoresistance of Co/ITO multilayers

The electrical and magnetic properties of Co/ITO multilayers with various ITO layer thickness are studied. Negative giant magnetoresistance with a maximum of −1.9% at room temperature and −2.57% at 15 K are observed. The magnitudes of GMR oscillate with a period of about 1 nm when varying the thickness of ITO layer.     

Mössbauer effect investigations of Co83Fe17/Au/Co/Au multilayers

[Co₈₃Fe₁₇/Au/Co/Au]_N sputter deposited multilayers displaying a giant magnetoresistance have been investigated. Complementary magnetic measurements were conducted in order to characterize a spin reorientation transition in Co₈₃Fe₁₇ layers sandwiched between Au spacers. The transition from a perpendicular magnetic anisotropy to easy-plane one takes place at the thickness of about 1 nm.     

Giant Magnetoresistance and Coercivity of electrodeposited multilayered FeCoNi/Cu and CrFeCoNi/Cu

The effect of Cr addition on electrodeposited multilayered nanowires CrFeCoNi/Cu was investigated from a magnetic property perspective: current perpendicular to the plane-Giant Magnetoresistance (CPP-GMR) and Coercivity (BH loops). The magnetic behavior of multilayered nanowires of CrFeNiCo/Cu was also affected by the alloy deposition potential, alloy pulsing time (layer thickness) and number of bilayers. Furthermore, the addition of Cr influenced both the nanowires GMR and Coercivity. Cr addition to the ferromagnetic FeCoNi layer induced a reduction in the room temperature GMR from 10.64% to 5.62%; however, the magnetic saturation field decreased from 0.45 to 0.27 T. The increase in the number of bilayers, from 1000 to 2500, resulted in a higher GMR value, 14.56% with 0.35 T magnetic saturation field. Addition of Cr to the ferromagnetic layer decreased the coercivity from 0.015 to 0.0054 T. Low saturation field CPP-GMR nanowires showing low coercivity at room temperature opens a new door for magnetic sensing devices. To the best of our knowledge, this is the first study on electrodeposited CrFeCoNi/Cu multilayered nanowires.     

Atomic structure and magnetic properties of Cu80Co20 nanocrystalline compound produced by mechanical alloying

Direct observation of the atomic structure of the mechanically alloyed Cu₈₀Co₂₀ compounds has been made using the field ion microscope (FIM). Phase composition, defect structure and morphology of material on the atomic scale have been determined. It has been established that the studied material is chemically inhomogeneous, presenting a mixture of two main phases: heterogeneous solid solution of cobalt in copper, and pure cobalt. Phase volume ratios, particle and cluster sizes have been estimated. An evaluation of Co content in Cu---Co solid solution has been made. The width of interfaces in this mechanically alloyed material was revealed to be at least twice the width of phase boundaries in metals and alloys. Superparamagnetism of the compound studied at elevated temperatures and saturation magnetization deficit at low temperatures are discussed on the basis of the above-mentioned structural data.     

Formation of Fe-Nb-X (X=Zr, Ti) amorphous alloys from pure metal elements by mechanical alloying

Fe-based amorphous powders of Fe₅₆Nb₆Zr₃₈ and Fe₆₀Nb₆Ti₃₄ based on binary eutectic were prepared by mechanical alloying starting from mixtures of pure metal powders. The amorphization behavior and thermal stability were examined by x-ray diffraction, scanning electron microscopy, transmission electron microscopy and differential scanning calorimetry. Results show that Fe₅₆Nb₆Zr₃₈ alloy has a better glass forming ability and a relatively lower thermal stability comparing with Fe₆₀Nb₆Ti₃₄ alloy. The prepared amorphous powders have homogeneous element distribution and no obvious contaminants coming from mechanical alloying. The synthesized amorphous powders offer the potential for consolidation to full density with desirable mechanical properties through the powder metallurgy methods.     

Parametric estimation of the Duffing system by using a modified gradient algorithm

The Letter presents a strategy for recovering the unknown parameters of the Duffing oscillator using a measurable output signal. The suggested approach employs the construction of an integral parametrization of one auxiliary output. It is calculated by measuring the difference between the output and its respective delay output. First we estimate the auxiliary output, followed by the application of a modified gradient algorithm, then we adjust the gains of the proposed linear estimator, until this error converges to zero. The convergence of the proposed scheme is shown using Lyapunov method.     

Microstructures and properties of high Cr content coatings on inner surfaces of carbon steel tubular components prepared by a novel mechanical alloying method

In the present work, a novel mechanical alloying method was developed to prepare high Cr content coatings on the inner surface of carbon steel tubular components using a planetary ball mill. The microstructure and elemental and phase composition of mechanically alloyed coatings at different processing conditions were studied using SEM, XRD, and EDX. It showed that a proper increase in the applied milling time and the disc rotation speed favored the improvement in the thickness, surface smoothness, densification level, and microstructural homogeneity of the deposited coatings. With processing conditions optimized (rotation speed of 500 rpm and milling time of 10 h), a fully dense, 120 μm thick, high Cr content coating, consisting of metal Cr and Fe-20Cr solid solution alloy, was metallurgically bonded to the inner substrate. Comparative studies on the microhardness, corrosion resistance, and anti-oxidation capability of carbon steel substrates with and without coatings were performed. It was found that the maximum microhardness of the coating reached HV_0.1667, showing a threefold improvement upon the substrate. The coated surfaces exhibited favorable resistance against corrosion and thermal oxidation as compared with the bare substrate. Based on two important action mechanisms (i.e., friction effect and impact effect) associated with a planetary ball mill, a reasonable mechanism was presented for the formation of mechanically alloyed coatings on inner surfaces of tubular components.     

Exchange bias in ferrimagnetic-antiferromagnetic nanocomposite produced by mechanical attrition

Nanoparticles comprising of magnetite (Fe₃O₄) core-hematite (α-Fe₂O₃) shell with mean diameter around 9 nm were synthesized by mechanical grinding. Zero-field-cooled (ZFC) and field-cooled (FC) magnetization and hysteresis loop measurements were carried out over the temperature range 5-300 K. Exchange bias varying from 140 to 10 Oe was observed. This is explained as arising due to ferrimagnetic-antiferromagnetic coupling at the nanointerfaces between the two phases. Analysis of data shows a pronounced increase in the effective anisotropy constant as the milling time is increased.     

Photoacoustic study of nanocrystalline silicon produced by mechanical grinding

Mechanical grinding (MG) was used to produce nanocrystalline silicon and its thermal and transport properties were investigated by photoacoustic absorption spectroscopy (PAS). The experimental results suggest that in as-milled nanocrystalline silicon for 10 h the heat transfer through the crystalline and interfacial components is similar, and after annealed at 470 °C the heat transfer is controlled by crystalline component.     

Morphologies,microstructures, and mechanical properties of samples produced using laser metal deposition with 316 L stainless steel wire

Laser metal deposition (LMD) with a filler has been demonstrated to be an effective method for additive manufacturing because of its high material deposition efficiency, improved surface quality, reduced material wastage, and cleaner process environment without metal dust pollution. In this study, single beads and samples with ten layers were successfully deposited on a 316 L stainless steel surface under optimized conditions using a 4000 W continuous wave fibre laser and an arc welding machine. The results showed that satisfactory layered samples with a large deposition height and smooth side surface could be achieved under appropriate parameters. The uniform structures had fine cellular and network austenite grains with good metallurgical bonding between layers, showing an austenite solidification mode. Precipitated ferrite at the grain boundaries showed a subgrain structure with fine uniform grain size. A higher microhardness (205–226 HV) was detected in the middle of the deposition area, while the tensile strength of the 50 layer sample reached 669 MPa. In addition, ductile fracturing was proven by the emergence of obvious dimples at the fracture surface.     

Electrostatic charging of single granules by repeated sliding along inclined metal plates

In this work, repeated sliding tests for single granules were investigated for their electrostatics generation. Several factors were considered including granule length-ratio, sliding face shape, sliding times, sliding area, sliding velocity, front-facing edge, plate inclined angle and humidity. Generally, it is found that electrostatics increases with granule length-ratio. Two kinds of granular sliding face shapes were used in this work, half circle and rectangle. Under the same working conditions, a granule with the sliding face shape of half-circle tends to produce more electrostatics than that of rectangle. In addition, the efficiency of granule charge generation increases with sliding times although the amount of impact charge is decreased by the initial charge. Electrostatics increases with sliding area, which is independent of granule sliding-face shape and sliding times. Electrostatics also increases with granule sliding velocity. Front-facing sliding with a short edge tends to generate more electrostatics than that with a long edge. In this work, three sliding-plate angles were chosen as 30°,54°,70°, where granules sliding along the inclined plate at 54° acquired the highest electrostatics in comparison with other two angles. Humidity has significant effect on electrostatics as that electrostatics decreases with humidity. At lower relative humidity, the granule length-ratio is found to have more effect on electrostatics.     

Simultaneous variations of microstructure and magnetic properties of Ni58Fe12Zr20B10 nanostructure/amorphous alloy prepared by mechanical alloying

This study aims to evaluate magnetic and micro-structural properties of amorphous/nanocrystalline mechanically alloyed Ni₅₈Fe₁₂Zr₂₀B₁₀ powders with ball-milling time up to 190 h. Structural, micro-structural and thermal evaluations of the milled powders were carried out by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM) and differential scanning calorimetry (DSC) methods. Magnetic properties were also measured by a vibrating sample magnetometer (VSM) instrument. Results showed that the amorphous phase reached maximum value of 95% and the crystallite size was about 3 nm at the end of the milling. Magnetization saturation (M_s) decreased slightly and coercivity (H_c) reached to the highest value at 72 h of the milling time. At the 190 h of milling, the coercivity and saturation magnetization reached 18 Oe and 20 emu/g, respectively. While, after an appropriate amount of heat treatment, these two variables became approximately 2 Oe and 32 emu/g.     

激光辐照金属丝产生电子束的发散度

研究了激光辐照金属丝产生电子束的自身磁场对其发散度的影响。通过理论分析和量级估算得到：电子在金属丝附近运动时,同时受到金属丝电场和自身磁场的作用,聚集效应明显;当电子离开金属丝后,空间电荷效应的库仑排斥作用与自身磁场的聚集作用量级相当,近似认为可以保持已经具有的发散度。利用经典轨迹蒙特卡罗方法模拟了该过程,计算结果表明自身磁场可以解释电子束的发散度及其对金属丝长度的依赖关系。     

Research on Zr50Al15−xNi10Cu25Yx amorphous alloys prepared by mechanical alloying with commercial pure element powders

Amorphous Zr₅₀Al_15−xNi₁₀Cu₂₅Y_x alloy powders were fabricated by mechanical alloying at low vacuum with commercial pure element powders. The effects on glass forming ability of Al partial substituted by Y in Zr₅₀Al₁₅Ni₁₀Cu₂₅ and thermal stability of Si₃N₄ powders addition were investigated. The as-milled powders were characterized by X-ray diffraction, scanning electron microscopy and differential scanning calorimeter. The results show that partial substitution of Al can improve the glass forming ability of Zr₅₀Al₁₅Ni₁₀Cu₂₅ alloy. Minor Si₃N₄ additions raise the crystallization activation energy of the amorphous phase and thus improve its thermal stability.     

Synthesis of copper-nickel nanoparticles prepared by mechanical milling for use in magnetic hyperthermia

Mechanical alloying of a mixture of copper and nickel powders has been applied for the preparation of copper-nickel alloy particles in the nanometer range. The particles were designed to be used for controlled magnetic hyperthermia applications. The milling conditions were optimized using the desired alloy composition. Utilizing a ball-to-powder mass ratio of 20, we could obtain a nanocrystalline Cu_27.5Ni_72.5 (at%) alloy with a crystallite size of around 10 nm and a Curie temperature of 45 °C.Thermal demagnetization in the vicinity of the Curie temperature of the nanoparticles was determined by thermomagnetic measurements using an adapted TGA-SDTA apparatus. The size and morphology of the particles were determined by XRD measurements and TEM analyses. The magnetic properties were also examined with a VSM. The magnetic heating effects were measured for the powdered material.