Thermoluminescence (TL) of europium-doped ZrO2 obtained by sol–gel method

This article reports the preparation and characterization of europium-doped zirconium oxide (ZrO₂:Eu³⁺) formed by homogeneous precipitation from propoxyde of zirconium [Zr(OC₃H₇)₄]. The alkoxide sol gel process is an efficient method to prepare the zirconium oxide matrix by the hydrolysis of alkoxide precursors followed by condensation to yield a polymeric oxo-bridged ZrO₂ network. All compounds were characterized by thermal analysis and the X-ray diffractometry method. The thermoluminescence (TL) emission properties of ZrO₂:Eu³⁺ under beta radiation effects are studied. The europium-doped sintered zirconia powder presents a TL glow curve with two peaks (Tmax) centered at around 204 and around 292 ^°C, respectively. TL response of ZrO₂:Eu³⁺ as a function of beta-absorbed dose was linear from 2 Gy up to 90 Gy. The europium ion (Eu³⁺)-doped ZrO₂ was found to be more sensitive to beta radiation than undoped ZrO₂ obtained by the same method and presented a little fading of the TL signal compared with undoped zirconium oxide.     

Synthesis and investigation of the luminescent properties of carbon doped lanthanum aluminate (LaAlO3) for application in radiation dosimetry

LaAlO₃ single crystals grown under hydrothermal conditions and co-doped with Ce and Dy atoms have been recently reported to show high thermoluminescent (TL) outputs for ultraviolet (UV) radiation fields (Oliveira et al., 2011). Due to this property, they have been considered for further investigation for applications in UV dosimetry. Encouraged by these results, we start an investigation about the TL properties of polycrystalline LaAlO₃ grown by an alternative method. In this method, equimolar amounts of Al₂O₃ and La₂O₃ are sintered, producing polycrystalline LaAlO₃ powder. Polycrystals doped with amounts of carbon ranging from 0.0 to 5.0 at.% were synthesized by sintering under hydrogen reducing atmosphere. After irradiation with a UV commercial lamp, the best TL outputs were observed for the undoped sample. The recorded TL glow curves show a main TL peak centered at 175 °C. The TL emission spectrum show a broad emission peak centered at 634 nm and another three narrow peaks centered at 724 nm, 738 nm and 754 nm, respectively. The undoped material show a huge TL output response for UV spectral irradiances ranging from 0.04 to 1.68 mJ cm⁻² that can be fitted by a 2nd order polynomial regression. The investigation demonstrates that undoped polycrystalline LaAlO₃ crystals sintered under reducing atmosphere are very attractive to be investigated as high sensitivity ultraviolet TL dosimeters.     

Thermoluminescence of Al2O3:Cr3+ films synthesized by the nonaqueous sol–gel method

The thermoluminescence (TL) properties of Al₂O₃:Cr³⁺ thin films prepared by the nonaqueous sol–gel method were evaluated. The obtained thin films were characterized by scanning electron microscope and energy dispersive spectrometry. They were irradiated with ⁶⁰Co gamma rays of the different doses. TL glow curves exhibited two peaks centered at 197°C and 322°C.The heights of peaks were found to be sensitive to exposures of ionizing irradiation and the integral area of the TL signals had a linear response in the dose range of 5–60 Gy.This remarkable result suggests that Al₂O₃:Cr³⁺ films might potentially be used for radiation dosimetry.     

Study of electrical conductivity changes and phase transitions in Co3O4 doped ZrO2

The electrical conductivity of ZrO₂ doped with Co₃O₄ has been measured at various temperatures for different molar ratios. The conductivity increases due to the migration of vacancies created by doping. The conductivity is also found to increase with rise in temperature up to 120°C, and after attaining a maximum the conductivity decreases due to a collapse of the lattice framework. A second rise in conductivity around 460°C in all the compositions confirms the phase transition in ZrO₂ from monoclinic to tetragonal symmetry. X-ray powder diffraction and DTA studies were carried out for confirming the doping effects and the transition in ZrO₂.     

α-Al2O3:C晶体的热释光和光释光特性

以高纯α-Al₂O₃和石墨为原料,采用温梯法生长了α-Al₂O₃：C晶体,使用Ris TL/OSL-DA-15型热释光和光释光仪研究了其热释光和光释光特性.α-Al₂O₃：C晶体在462K附近有单一热释光峰,发射波长位于410nm.随着辐照剂量的增加,热释光强度逐渐增强,462K的热释光特征峰位置保持不变.α-Al₂O₃：C晶体的 关键词： 2O₃：C')" href="#">α-Al₂O₃：C 热释光 光释光     

Long lasting phosphorescent properties of Ti doped ZrO2

A novel long-lasting afterglow phosphor ZrO₂:Ti is prepared by the conventional solid-stated method and their luminescent properties are investigated. A bluish white strong and broad emissive band, which is attributed to originate from the recombination of electrons trapped by F⁺ centers and the holes created in Valence band, is observed under 254 nm UV irradiation. The identical color long afterglow, which lasts about 1 h, is found in the ZrO₂:Ti phosphor after removing the 254 nm UV light. The mechanism of the long lasting phosphorescence (LLP) has been discussed based on the thermoluminescence (TL) results. The replacement of Zr by Ti produces more anion vacancies, resulting in the enhanced photoluminescence (PL) and LLP of ZrO₂:Ti sample. These results indicate that ZrO₂:Ti phosphor has potential promising applications.     

Dosimetric properties of rare earth doped LiCaBO3 thermoluminescence phosphors

Lithium Calcium borate (LiCaBO₃) polycrystalline thermoluminescence (TL) phosphor doped with rare earth (RE³⁺) elements has been synthesized by high temperature solid state diffusion reaction. The reaction has produced a very stable crystalline LiCaBO₃:RE³⁺ phosphors. Among these RE³⁺ doped phosphors thulium doped material showed maximum TL sensitivity with favorable glow curve shape. TL glow curve of gamma irradiated LiCaBO₃:Tm³⁺ samples had shown two major well-separated glow peaks at 230 and 430 °C. The glow peak at 430 °C is almost thrice the intensity of the glow peak at 230 °C. The TL sensitivity of the phosphor to gamma radiation was about eight times that of TLD-100 (LiF). Photoluminescence and TL emission spectra showed the characteristic Tm³⁺ peaks. TL response to gamma radiation dose was linear up to 10³ Gy. Post-irradiation TL fading on storage in room temperature and elevated temperatures was studied in LiCaBO₃:Tm³⁺ phosphor.     

Swift ion irradiation effect on high-k ZrO2- and Al2O3-based MOS devices

This paper describes the heavy ion-induced effects on the electrical characteristics of reactively sputtered ZrO₂ and Al₂O₃ high-k gate oxides deposited in argon plus nitrogen containing plasma. Radiation-induced degradation of sputtered high-k dielectric ZrO₂/Si and Al₂O₃/Si interface was studied using 45?MeV Li³⁺ ions. The devices were irradiated with Li³⁺ ions at various fluences ranging from 5?×?10⁹ to 5?×?10¹²?ions/cm². Capacitance–voltage and current–voltage characteristics were used for electrical characterization. Shift in flat band voltage towards negative value was observed in devices after exposure to ion radiation. Post-deposition annealing effect on the electrical behavior of high-k/Si interface was also investigated. The annealed devices showed better electrical and reliability characteristics. Different device parameters such as flat band voltage, leakage current, interface defect density and oxide-trapped charge have been extracted.The surface morphology and roughness values for films deposited in nitrogen containing plasma before and after ion radiation are extracted from Atomic Force Microscopy.     

Effect of SiO2 nanoparticles sizes on the optical properties and radiation resistance of powder mixtures ZrO2 with micron sizes

One way to improve photo- and radiation resistance of materials is by the modification of their nanoparticles. The purpose of work is to study the optical properties and radiation resistance of ZrO₂ powder mixtures with SiO₂ nanoparticles without high-temperature heating. The ZrO₂ powders with micron sizes were mixed in a ratio of 100:7 mas.% with SiO₂ nanopowders. The nanopowders were obtained by combustion of silicon tetrachloride in air plasma. Samples were characterized using X-ray diffraction (XRD), high resolution scanning electron microscopy (SEM), and a simulator of the environment of outer space “Spectrum”. The radiation resistance increase of zirconia dioxide powders with micron-sized grains by the addition of silica nanoparticles without heating at a high temperature was found. For these purposes only water evaporation at 150 °C was used. The effectiveness of the modification reaches values of 2.1 times. This value is close to or even more in comparison to its values in the modification by using high-temperature heating. This result is significant for the practical use of this method of incensement of the radiation resistance of oxide reflecting powders.     

Preparation of sol-gel ZrO2-SiO2 highly reflective multilayer films and laser-induced damage threshold characteristic

Sol-gel (ZrO₂/SiO₂)¹² ZrO₂ films were prepared by spin coating method. The reflectivity spectrum of the films was measured with a Lambda 900 spectrometer. In order to investigate laser-induced damage threshold (LIDT) characteristic of highly reflective films, one-layer ZrO₂ and SiO₂ films, two-layer ZrO₂/SiO₂ and SiO₂/ZrO₂ films were also prepared by spin coating method. LIDT of each film was measured. Damage morphology after laser irradiation was characterized by optical microscopy (Nikon E600K). The experimental results showed that the reflectivity of (ZrO₂/SiO₂)¹² ZrO₂ film at 1064 nm and 355 nm wavelength is 99.7%. The LIDT results decreases as the number of layer of films increases. All the films have similar damage morphology. The experimental results are explained by the different temperature profiles of the films.     

Influence of Some Parameters on the Synthesis of ZrO2 Nanoparticles by Heating of Alcohol–aqueous Salt Solutions

Parameters that influence ZrO₂ (3-mol% Y₂O₃ stabilized) nanoparticles prepared by heating of alcohol–aqueous salt solutions were investigated. It revealed that the kind of alcohol used significantly affected the particle size and morphology of the as synthesized nano-ZrO₂ powders. The ratio of alcohol to water (R/H) was also important to conduct the gelation process. The dispersion and sintering behavior of the powder could be optimized via aging. By carefully controlling the process, weakly agglomerated ZrO₂ nanoparticles with an average particle size of 13-nm (TEM) were achieved. The classical DLVO theory was employed to clarify the effect of solvent on powder morphology, an aging mechanism was proposed as well.     

Synthesis, photoluminescence, thermoluminescence and dosimetry properties of novel phosphor Zn(BO2)2:Tb

Polycrystalline powder samples of terbium doped Zn(BO₂)₂ phosphors were prepared by solid state reaction in the thermal carbon reducing atmosphere at high temperature. The photoluminescence (PL), three-dimensional (3D) TL emission spectrum and dosimetric characteristics following ⁶⁰Co gamma-rays irradiation were studied. Characteristic emission bands of Tb³⁺ at about 490, 543, 584 and 620 nm, attributed to the ⁵D₄→⁷F_J (J=3, 4, 5, 6) transitions of Tb³⁺ ions, were observed in the TL and PL emission spectrum. No emission from Tb⁴⁺ ions was observed in the TL emission spectrum. The TL-dose response of the powder samples Zn(BO₂)₂:Tb to ⁶⁰Co gamma-rays radiation in the dose range from 1 to 100 Gy for clinical dose levels was almost linear. The experiment results showed that Zn(BO₂)₂:Tb has potential use as the materials of gamma-rays thermoluminescence dosimeter (TLD) for clinical dosimetry.     

Intrinsic defect related luminescence in ZrO2

The studies of ZrO₂ and yttrium stabilized ZrO₂ nanocrystals luminescence as well as yttrium stabilized single crystal luminescence and induced absorption showed that the intrinsic defects are responsible for luminescence at room temperature. These defects form a quasi-continuum of states in ZrO₂ band gap and are the origin of the luminescence spectrum dependence on the excitation energy. Luminescence centers are oxygen vacancies related but not the vacancies themselves. At room temperature, in ZrO₂, deep traps for electrons and holes exist. The oxygen vacancies are proposed to be the traps for electrons.     

On the Radiation Hardness of Thermostabilizing BaTiZrO<Subscript>3</Subscript> Coatings in situ Deposited by the Detonation Method

The radiation hardness of three types of BaTiZrO₃ coatings obtained by synthesis from the powder mixtures BaTiO₃ + ZrO₃, BaCO₃ + TiO₂ + ZrO₃ (micron size), and BaCO₃ + TiO₂ + ZrO₃ (nanopowder) deposited by the detonation method on metal substrates is investigated. The high radiation resistance of all types of coatings to the action of electrons with an energy of 30 keV and a fluence of up to 4 × 10¹⁶ cm^–2 is established in measurements of the diffuse reflection spectra in vacuum at the place of irradiation (in situ).     

High-rate reactive magnetron sputtering of zirconia films for laser optics applications

ZrO₂ exhibits low optical absorption in the near-UV range and is one of the highest laser-induced damage threshold (LIDT) materials; it is, therefore, very attractive for laser optics applications. This paper reports explorations of reactive sputtering technology for deposition of ZrO₂ films with low extinction coefficient k values in the UV spectrum region at low substrate temperature. A high deposition rate (64 % of the pure metal rate) process is obtained by employing active feedback reactive gas control which creates a stable and repeatable deposition processes in the transition region. Substrate heating at 200 °C was found to have no significant effect on the optical ZrO₂ film properties. The addition of nitrogen to a closed-loop controlled process was found to have mostly negative effects in terms of deposition rate and optical properties. Open-loop O₂ gas-regulated ZrO₂ film deposition is slow and requires elevated (200 °C) substrate temperature or post-deposition annealing to reduce absorption losses. Refractive indices of the films were distributed in the range n = 2.05–2.20 at 1,000 nm and extinction coefficients were in the range k = 0.6 × 10^?4 and 4.8 × 10^?3 at 350 nm. X-ray diffraction analysis showed crystalline ZrO₂ films consisted of monoclinic + tetragonal phases when produced in Ar/O₂ atmosphere and monoclinic + rhombohedral or a single rhombohedral phase when produced in Ar/O₂ + N₂. Optical and physical properties of the ZrO₂ layers produced in this study are suitable for high-power laser applications in the near-UV range.     

Study on preparation and properties of molybdenum alloys reinforced by nano-sized ZrO<Subscript>2</Subscript> particles

The nano-sized ZrO₂-reinforced Mo alloy was prepared by a hydrothermal method and a subsequent powder metallurgy process. During the hydrothermal process, the nano-sized ZrO₂ particles were added into the Mo powder via the hydrothermal synthesis. The grain size of Mo powder decreases obviously with the addition of ZrO₂ particles, and the fine-grain sintered structure is obtained correspondingly due to hereditation. In addition to a few of nano-sized ZrO₂ particles in grain boundaries or sub-boundaries, most are dispersed in grains. The tensile strength and yield strength have been increased by 32.33 and 53.76 %.     

XPS investigation of diffusion of two-layer ZrO2/SiO2 and SiO2/ZrO2 sol–gel films

Two-layer ZrO₂/SiO₂ and SiO₂/ZrO₂ films were deposited on K9 glass substrates by sol–gel dip coating method. X-ray photoelectron spectroscopy (XPS) technique was used to investigate the diffusion of ZrO₂/SiO₂ and SiO₂/ZrO₂ films. To explain the difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films, porous ratio and surface morphology of monolayer SiO₂ and ZrO₂ films were analyzed by using ellipsometry and atomic force microscopy (AFM). We found that for the ZrO₂/SiO₂ films there was a diffusion layer with a certain thickness and the atomic concentrations of Si and Zr changed rapidly; for the SiO₂/ZrO₂ films, the atomic concentrations of Si and Zr changed relatively slowly, and the ZrO₂ layer had diffused through the entire SiO₂ layer. The difference of diffusion between ZrO₂/SiO₂ and SiO₂/ZrO₂ films was influenced by the microstructure of SiO₂ and ZrO₂.     

Influences of CO2 laser annealing on mechanical and laser-induced damage properties of ZrO2 thin films

Zirconium dioxide (ZrO₂) thin films were deposited on BK7 glass substrates by the electron beam evaporation method. A continuous wave CO₂ laser was used to anneal the ZrO₂ thin films to investigate whether beneficial changes could be produced. After annealing at different laser scanning speeds by CO₂ laser, weak absorption of the coatings was measured by the surface thermal lensing (STL) technique, and then laser-induced damage threshold (LIDT) was also determined. It was found that the weak absorption decreased first, while the laser scanning speed is below some value, then increased. The LIDT of the ZrO₂ coatings decreased greatly when the laser scanning speeds were below some value. A Nomarski microscope was employed to map the damage morphology, and it was found that the damage behavior was defect-initiated both for annealed and as-deposited samples. The influences of post-deposition CO₂ laser annealing on the structural and mechanical properties of the films have also been investigated by X-ray diffraction and ZYGO interferometer. It was found that the microstructure of the ZrO₂ films did not change. The residual stress in ZrO₂ films showed a tendency from tensile to compressive after CO₂ laser annealing, and the variation quantity of the residual stress increased with decreasing laser scanning speed. The residual stress may be mitigated to some extent at proper treatment parameters.     

Thermoluminescence and opitical absorption of BaF2 crystals

Abstract

Nominally pure and Dy-doped BaF₂ crystals were investigated concerning their optical absorption (OA) and thermoluminescence (TL) properties. Peaks at 120—150 and 200°C were observed for a heating rate of 1.7°C/s. The TL response for γ-rays and the TL emission spectra were obtained for these peaks. Except for the purest crystal, all BaF₂ crystals produced OA bands before irradiation typical of Ce³⁺ ions. After irradiation, Dy doped crystals showed bands due to Dy²⁺ ions. A nominally pure sample gave bands related to Ce²⁺ ions and photochromic centers of Ce³⁺ ions. and photochromic centres of Ce³⁺ ions. The correlation between some OA bands and TL peaks is discussed.     

Production and characterization of spodumene dosimetric pellets by prepared by pechini and proteic sol–gel route

Spodumene is an aluminosilicate that has proven suitable for high-dose TL dosimetry of beta or gamma rays. Due to the presence of lithium in its chemical composition (LiAlSi₂O₆ – β-LAS), it has potential as neutron dosimeter as well. This silicate may be obtained naturally or synthetically. The synthetic LAS has been produced by solid state reaction and conventional sol–gel, whose difficulty arises from the need to employ high temperatures and high cost reagents, respectively. Alternative routes like Pechini and proteic sol–gel methods are promising, because they can reduce production costs and the possibility of environmental pollution. This work aimed at producing spodumene with the proteic sol–gel method using edible unflavored gelatin as a precursor and also with the Pechini method. The products were characterized physically and morphologically, and their applicability as TL dosimeter was investigated, comparing the sensitivity of samples produced by different methods. Two sets of samples were produced using different sources of silicon, tetraethyl orthosilicate (TEOS, Si(C₂H₅O)₄) and silica (SiO₂). The materials produced were characterized by X-ray diffraction and by thermal analysis in order to evaluate their structural properties, as well as possible temperature-dependent changes in physical or chemical properties. The syntherized pellets produced with these crystals were irradiated with a ⁹⁰Sr–⁹⁰Y source and their TL glow curves were evaluated. The production of β-LAS was successful by both methods, either using silica or TEOS as a silicon source. The crystals were obtained using much lower temperatures than by methods described in literature. We observed that the method of powder production was critical to develop a radiation detector: the best TL material was the powder produced using silica and the Pechini Method.