Radical polymerization of vinyl acetate with primary radical termination

Vinyl acetate was polymerized at high initiation rate with 2,2′-azobis(2,4-dimethyl valeronitrile) as initiator at 50°C. In this polymerization, the power dependence of polymerization rate on the initiation rate is smaller than at lower concentration of monomer. This dependence was kinetically analyzed at each given concentration of monomer. Average degree of polymerization of polymer formed depends on the concentration of initiator. This dependence was explained by considering chain and primary radical terminations and transfer to monomer of polymer radical, and the initiator efficiency (=0.503) was deduced. It was found that the chain termination is inversely proportional to solvent viscosity, but the primary radical termination is not inversely proportional to solvent viscosity. Further, the value of the primary radical termination rate constant (=1.4 × 10⁹l./mole-sec) was estimated.     

Analysis of polymerization rates in radical polymerization with primary radical termination of methyl methacrylate initiated by 2,2′-azobis(2,4-dimethyl valeronitrile)

Polymerization rates in radical polymerization of methyl methacrylate initiated by 2,2′-azobis(2,4-dimethyl valeronitrile) under various conditions were analyzed by using a previously derived simple equation. The results obtained are discussed on the basis of the relation of solvent viscosity and temperature. It is concluded that chain termination rate constant is inversely proportional to the solvent viscosity, but primary radical termination rate constant can not be related immediately to solvent viscosity.     

Determination of propagation and termination rate constants for some methacrylates in their radical polymerizations

Rotating sector determinations of k_p and 2k_t for ten methacrylates undergoing radical polymerization were carried out at 30°C. Ester groups in the monomers were: isopropyl, ethyl, β-cyclohexylethyl, methyl, γ-phenylpropyl, β-phenylethyl, β-methoxyethyl, benzyl, β-chloroethyl, and phenyl. Values of k_p obtained were 121, 126, 1190, 141, 149, 228, 249, 1250, 254, and 411 l./mole-sec., respectively; values of 2k_t × 10^?6 were 4.52, 7.35, 32.8, 11.6, 0.813, 1.88, 9.30, 41.9, 6.71, and 11.9 l./mole-sec., respectively. Omitting the data for the β-cyclohexylethyl and benzyl esters, a Taft correlation, log k_p = (0.70 ± 0.18)σ* + 2.2, was established, where σ* denotes Taft's polar substitutent constants for the above-mentioned ester groups. The steric substituent constants E_s were found to have no influence on k_p. Combination of k_p with r₂ data from copolymerization studies with styrene or methyl methacrylate as M₁ comonomer revealed that the more reactive monomer gave rise to the more reactive polymer radical. Monomer viscosities and molar volumes of the ester groups were found to correlate with 2k_t.     

Evaluation of polymerization rate by chain length dependence on polymer–polymer termination and primary radical termination in radical polymerization

In order to analyze the polymerization rate at high initiation rate and/or low monomer concentration, the rate equations are derived by a rate formulated previously for polymer–polymer termination and another rate for primary radical termination, which is formulated here (both rates depend on chain length of polymer radical). Such equations would be applicable to the kinetic data in the polymerizations of styrene and methyl methacrylate. This shows that the assumption that both rates are independent of chain length overestimates the rate of primary radical termination.     

Kinetics of radical polymerization of dimethylphenyl methacrylates

The kinetics of free radical polymerization of all six existing isomeric dimethylphenyl methacrylates were studied in bulk at 60°C, initiated by dilauroyl peroxide, using dilatometry. The different polymerization rates observed, resulting from the different monomer structures, are discussed in terms of steric and other effects, considering also the previous results for tolyl methacrylates. © 1993 John Wiley & Sons, Inc.     

Effect of solvent on chain propagation and termination reaction rates in radical polymerization

The radical polymerizations of acrylamide and methacrylamide and of acrylic, methacrylic and fluoroacrylic acids have been studied in various solvents. The nature of the solvent affects the overall rate due to changes in k_p and E_p. It has been shown that the effect of solvent also depends on the nature of the monomer. A possible explanation of the observed behaviour is discussed.     

Stereocontrol in the free‐radical polymerization of methacrylates with fluoroalcohols

The free‐radical polymerization of methyl methacrylate (MMA), ethyl methacrylate (EMA), isopropyl methacrylate (IPMA), and tert‐butyl methacrylate (t‐BuMA) was carried out under various conditions to achieve stereoregulation. In the MMA polymerization, syndiotactic specificity was enhanced by the use of fluoroalcohols, including (CF₃)₃COH as a solvent or an additive. The polymerization of MMA in (CF₃)₃COH at −98 °C achieved the highest syndiotacticity (rr = 93%) for the radical polymerization of methacrylates. Similar effects of fluoroalcohols enhancing syndiotactic specificity were also observed in the polymerization of EMA, whereas the effect was negligible in the IPMA polymerization. In contrast to the polymerizations of MMA and EMA, syndiotactic specificity was decreased by the use of (CF₃)₃COH in the t‐BuMA polymerization. The stereoeffects of fluoroalcohols seemed to be due to the hydrogen‐bonding interaction of the alcohols with monomers and growing species. The interaction was confirmed by NMR measurements. In addition, in the bulk polymerization of MMA at −78 °C, syndiotactic specificity and polymer yield increased even in the presence of a small amount {[(CF₃)₃COH]/[MMA]_o < 1} of (CF₃)₃COH. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4693–4703, 2000     

Thermal and radical polymerization of anthracene acrylates and methacrylates

The thermal and radical-induced polymerizations of 9-anthrylmethyl acrylate ( I ), 9-anthrylmethyl methacrylate ( II ), 1′-(9-anthryl)ethyl acrylate ( III ), and 1′-(9-anthryl)ethyl methacrylate ( IV ) have been studied. It was found that the radical-induced polymerization takes place for the methacrylates only, while thermal polymerization leads to polymers for both types of monomers and takes place by Diels–Alder cycloaddition in the case of acrylates, and by both normal enchainment and Diels–Alder cycloaddition in the case of methacrylates.     

A new method for evaluation of the characteristic constant for primary radical termination in free radical polymerization

A new model has been proposed for estimation of the characteristic rate constant for primary radical termination, using the radical life time, rate of polymerization, and rate of initiation. The model can be used to estimate the characteristic rate constant for primary radical termination under most conditions of free radical polymerization. By applying this model to high conversion polymerization data, it is possible to compare the conversion dependence of the characteristic rate constant for primary radical termination and initiation rate as well as the conversion dependence of the termination rate constant.The model has applied to various published experimental data and the results compared with literature values.     

Control of a living radical polymerization of methacrylates by light

On-off: A living radical polymerization procedure, which utilizes ppm levels of an iridium-based photoredox catalyst, affords control over chain growth through mediation by visible light (see scheme; P(n) =polymer chain, X=halogen, M=monomer). This process can be activated and deactivated by light, enables control over the molecular weight and molecular weight distributions, and tolerates different functional groups.     

Synthesis and radical polymerization of hydrophilic methacrylates with oxyethylene units in the pendant chain

The syntheses of methacrylic monomers of the general structure where n is 3, 4, 5, or 6, were performed by the reaction of the corresponding alcohol ethers with methacryloyl chloride. The alcohol ethers were previously prepared by different synthetic procedures involving the monoetherification of the starting glycols. The polymerizations kinetics of the monomers were examined at several temperatures in the bulk and in dioxane solutions. NMR spectroscopy and electron paramagnetic resonance techniques were used to study the kinetics of polymerization. The polymerization rate parameter, expressed as (2f)^1/2k_p/〈k_t〉^1/2, and the values of the propagation rate coefficient k_p and the termination rate coefficient 〈k_t〉/f, where f is the efficiency factor of the initiator, were determined. The reactivity of the monomers depended on the size of the ester residue in such a way that the longer the lateral chain was, the higher the polymerization rate was and the lower the termination rate coefficient was. On the contrary, the dependence of k_p on the chemical structure was very small. In the solution polymerizations of all these monomers (monomer concentration = 1 mol L^?1), the radical concentrations remained almost constant until very high conversions, whereas in the bulk, a different behavior was observed that depended on the number of oxyethylene units in the side chain of the monomer. In this sense, for n = 4, 5, or 6, the radical concentration remained almost invariable with the reaction time, whereas for n = 3, a moderate increase occurred at low conversions, contrasting with the important increase observed at similar conversions for n = 1. This showed that the gel effect in these methacrylic monomers was greatly dependent on the number of bonds of the lateral chain. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1567–1579, 2003     

Primary radical termination rate constant at high conversion in radical polymerization

A primary radical termination rate constant given by: k_ti = A_1iD_i, where A_1i is a constant and D_i is the diffusion constant of the primary radical, was examined on the basis of the variation of conversion. It was proved that this rate constant is correct at high conversion. A relationship between primary radical termination rate constant and conversion was derived. The effect of variation of conversion on the gel effect is discussed.     

Stereocontrol during the free‐radical polymerization of methacrylates with Lewis acids

The free‐radical polymerizations of methyl methacrylate (MMA), ethyl methacrylate, isopropyl methacrylate, and 2‐methoxyethyl methacrylate were carried out in the presence of various Lewis acids. The MMA polymerization in the presence of scandium trifluoromethanesulfonate [Sc(OTf)₃] in toluene or CHCl₃ produced a polymer with a higher isotacticity and heterotacticity than that produced in the absence of Sc(OTf)₃. Similar effects were observed during the polymerization of the other monomers. ScCl₃, Yb(OTf)₃, Er(OTf)₃, HfCl₄, HfBr₄, and In(OTf)₃ also increased the isotacticity and heterotacticity of the polymers. The effects of the Lewis acids were greater in a solvent with a lower polarity and were negligible in tetrahydrofuran and N,N‐dimethylformamide. Sc(OTf)₃ was also found to accelerate the polymerization of MMA. On the basis of an NMR analysis of a mixture of Sc(OTf)₃, MMA, and poly(methyl methacrylate), the monomer–Sc(OTf)₃ interaction seems to be involved in the stereochemical mechanism of the polymerization. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1463–1471, 2001     

Studies in vinyl chloride polymerization. Determination of primary radical termination by initiator fragment method

The rate of vinyl chloride polymerization initiated by doubly labelled benzoyl peroxide in dichloroethane at 60° was measured dilatometrically. The extent of primary radical termination, evaluated from the assay of the polymer samples recovered at 10% conversion, is compared with values deduced from analysis of the kinetic data.     

Diffusion-controlled rate constant of termination reaction in radical polymerization

Smoluchowski's theory has been modified and the improved theory was applied to diffusion-controlled polymerization. This application proved that the rate-controlling process is not transrational diffusion but the segmental diffusion. The segmental diffusion-controlled rate constant was derived by the collision theory. This rate constant explains the experimental fact that the diffusion-controlled rate constant of bimolecular termination in radical polymerization of alkyl methacrylate is inversely proportional to solution viscosity and independent of the molecular weight of the polymeric free radical.     

Copper(I)-mediated radical polymerization of methacrylates in aqueous solution

α-Methoxypolyethylene oxide methacrylate was polymerized by copper(I)-mediated living radical polymerization in aqueous solution to give polymers with controlled number-average molecular masses and narrow polydispersities. When equimolar quantities of initiator with respect to copper(I) bromide were used, the reaction was extremely fast with quantitative conversion achieved in less than 5 min at ambient temperature. However, the molecular weight distribution was broad, and control over the number-average molecular weight (M_n) growth was extremely poor; this is ascribed to an increase in termination because of the increased rate as a result of the coordination of water at the copper center. The complex formed between copper(I) bromide and N-(n-propyl)-2-pyridylmethanimine, bis[N-(n-propyl)-2-pyridylmethanimine]copper(I), was demonstrated to be stable in aqueous solution by ¹H NMR over 10 h at 25 °C. However, on increasing the temperature to 50 °C, decomposition occurred rapidly. Thus, polymerization temperatures were maintained at ambient temperature. When longer alkyl chains were utilized in the ligand, that is, pentyl and octyl, the complex acted as a surfactant leading to heterogeneous solutions. When the catalyst concentration was reduced by two orders of magnitude, the rate of polymerization was reduced with 100% conversion achieved after 60 min with the M_n of the final product being higher than that predicted and the polydispersity equal to 1.43. Copper(II) was added as an inhibitor to circumvent these problems. When 10% of Cu(I) was replaced by Cu(II) {[Cu(I)] + [Cu(II)]/[I] = 1/100}, the mass distribution showed a bimodal distribution, and the rate of polymerization decreased significantly. With a catalyst composition [Cu(I)]/[Cu(II)] = 0.5/0.5 {[Cu(I)] + [Cu(II)]}/[I] = 1/100, polymerization proceeded slowly with 80% conversion reached after 22 h. Thus, the concentration of Cu(I) was further reduced with [Cu(I)]/[Cu(II)] = 10/90, {[Cu(I)] + [Cu(II)]}/[I] = 1/100. The system then contained [Initiator]/[Cu(I)] = 1000/1 and [I]/[Cu(II)] = 1000/9. Under these conditions, the reaction reached 50% after 5 h with the polymer having both an M_n close to the theoretical value and a narrow polydispersity of PDi = 1.15. Optimum results were obtained by increasing the amount of catalyst. When a ratio of [Cu(I)]/[Cu(II)] = 10/90 with a ratio of [Cu]/[I] = 1/1, a conversion of 100% was achieved after less than 20 h, leading to a product having M_n = 8500 and PDi = 1.15. Decreasing the amount of Cu(II) relative to Cu(I) to [Cu(I)]/[Cu(II)] = 0.5/0.5 (maintaining the overall amount of copper) led to 100% conversion after 75 min: M_n = 9500, PDi = 1.10. Block copolymers have been demonstrated by sequential monomer addition with excellent control over M_n and PDi. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1696–1707, 2001     

Synthesis of graft copolyimides via controlled radical polymerization of methacrylates with a polyimide macroinitiator

The atom-transfer radical polymerization of methyl methacrylate and tert-butyl methacrylate with a polyimide multicenter macroinitiator in the presence of a CuCl-2,2′-bipyridine catalytic system is investigated. The kinetic features of the process, the molecular-weight characteristics of the formed side chains, and the post-polymerization of methyl methacrylate with graft polyimides containing polymethacrylate side chains are studied. The conditions of controlled polymerization yielding graft copolyimides with narrowly dispersed living poly(methyl methacrylate) or poly(tert-butyl methacrylate) side chains of variable lengths are determined.     

Non-ideal kinetics in vinyl polymerization: Note on primary radical termination in benzoyl peroxide initiated polymerization of vinyl chloride in dichloroethane

The kinetics of vinyl chloride polymerization initiated by benzoyl peroxide doubly labelled with ¹⁴C and 'H were studied in 1,2-dichloroethane solution at 60°. The importance of primary radical termination in the polymerization is examined by kinetic analysis and by analysis of polymers for combined initiator fragments.