Optical and electrical properties of swift heavy ion beam-irradiated polycarbonate/polystyrene bilayer films

Polycarbonate/polystyrene bilayer films prepared by solvent-casting method were irradiated with 55 MeV carbon ion beam at different fluences ranging from 1×10¹¹ to 1×10¹³ ions cm^?2. The structural, optical, surface morphology and dielectric properties of these films were investigated by X-ray diffraction (XRD), UV–visible spectroscopy, Fourier-transform infrared (FTIR) spectroscopy, optical microscopy and dielectric measurements. The XRD pattern shows that the percentage of crystallinity decreases while inter-chain separations increase with ion fluence. UV–visible spectroscopy shows that the energy band gap decreases and the number of carbon atoms in nanoclusters increase with the increase in ion fluences. The refractive index is also found to decrease with the increase in the ion fluence. Optical microscopy shows that after irradiation polymeric bilayer films color changes with ion fluences. The FTIR spectra evidenced a very small change in cross-linking and chain scissoring at high fluence. Dielectric constant decreases while dielectric loss and AC conductivity increase with ion fluences.     

Electron-Beam-Induced Modifications in High-Density Polyethylene

Post-irradiation studies have been carried out to elucidate the effects of electron beam irradiation on the structural, optical, dielectric, and thermal properties of high-density polyethylene (HDPE) films. The experimental results showed that both the optical band gap and activation energy of HDPE films decreases with an increase in the doses of electron radiation. The electrical measurements showed that dielectric constant and the ac conductivity of HDPE increases with an increase in the dose of electron radiation. The thermal analysis carried out using DSC and TGA revealed that the melting temperature, degree of crystallinity, and thermal stability of the HDPE films increased, obviously, due to the predominant cross-linking reaction following high doses of electron irradiation.     

Electron-beam irradiation effects on poly(ethylene-co-vinyl acetate) polymer

Poly(ethylene-co-vinyl acetate) (EVA) films were irradiated with a 1.2 MeV electron beam at varied doses over the range 0–270 kGy in order to investigate the modifications induced in its optical, electrical and thermal properties. It was observed that optical band gap and activation energy of EVA films decreased upon electron irradiation, whereas the transition dipole moment, oscillator strength and number of carbon atoms per cluster were found to increase upon irradiation. Further, the dielectric constant, the dielectric loss, and the ac conductivity of EVA films were found to increase with an increase in the dose of electron radiation. The result further showed that the thermal stability of EVA film samples increased upon electron irradiation.     

High energy electron irradiation effects on polystyrene films

The effect of an 8 MeV electron-beam on the structural, optical and dielectric properties of polystyrene films has been investigated respectively by means of Fourier transform infrared (FTIR) spectroscopy, ultraviolet–visible (UV–VIS) spectroscopy and electrical impedance (LCR) analysis over a radiation dose in the range of 50–250 kGy using a Microtron accelerator. The FTIR spectral analysis shows no change in the overall structure of the irradiated polystyrene films, except a minor change in the intensity of a few peaks in the FTIR spectrum, indicating that polystyrene is resistant to electron-beam irradiation over the range of radiation doses investigated. The optical band gap analysis using the UV–VIS absorption spectra of the polystyrene shows a small decrease in the optical band gap (E _g) and the activation energy with an increase in electron doses. Further, the dielectric measurements over a frequency range of 100 Hz to 1 MHz for the electron-beam-irradiated polystyrene films show that both the dielectric constant and the dielectric loss increase with an increase in electron radiation dose, which may be ascribed to the formation of defect sites in the band gap of polystyrene as a consequence of molecular chain scission in the polymer films upon irradiation.     

Optical and electrical properties of plasma-oxidation derived HfO2 gate dielectric films

High-k gate dielectric HfO₂ thin films have been deposited on Si(1 0 0) by using plasma oxidation of sputtered metallic Hf thin films. The optical and electrical properties in relation to postdeposition annealing temperatures are investigated by spectroscopic ellipsometry (SE) and capacitance-voltage (C-V) characteristics in detail. X-ray diffraction (XRD) measurement shows that the as-deposited HfO₂ films are basically amorphous. Based on a parameterized Tauc-Lorentz dispersion mode, excellent agreement has been found between the experimental and the simulated spectra, and the optical constants of the as-deposited and annealed films related to the annealing temperature are systematically extracted. Increases in the refractive index n and extinction coefficient k, with increasing annealing temperature are observed due to the formation of more closely packed thin films and the enhancement of scattering effect in the targeted HfO₂ film. Change of the complex dielectric function and reduction of optical band gap with an increase in annealing temperature are discussed. The extracted direct band gap related to the structure varies from 5.77, 5.65, and 5.56 eV for the as-deposited and annealed thin films at 700 and 800 °C, respectively. It has been found from the C-V measurement the decrease of accumulation capacitance values upon annealing, which can be contributed to the growth of the interfacial layer with lower dielectric constant upon postannealing. The flat-band voltage shifts negatively due to positive charge generated during postannealing.     

Effect of Ar bombardment on the electrical and optical properties of low-density polyethylene films

The influence of low-energy Ar ion beam irradiation on both electrical and optical properties of low-density polyethylene (LDPE) films is presented. The polymer films were bombarded with 320 keV Ar ions with fuences up to 1×10¹⁵ cm^?2. Electrical properties of LDPE films were measured and the effect of ion bombardment on the DC conductivity, dielectric constant and loss was studied. Optically, the energy gap, the Urbach’s energy and the number of carbon atoms in a cluster were estimated for all polymer samples using the UV–Vis spectrophotometry technique. The obtained results showed slight enhancement in the conductivity and dielectric parameters due to the increase in ion fluence. Meanwhile, the energy gap and the Urbach’s energy values showed significant decrease by increasing the Ar ion fluence. It was found that the ion bombardment induced chain scission in the polymer chain causing some carbonization. An increase in the number of carbon atoms per cluster was also observed.     

Dielectric behaviour of emeraldine base polymer–ZnO nanocomposite film in the low to medium frequency

Emeraldine base (EB) polymer–ZnO nanoparticles composite films has been synthesized by solution casting technique on ITO-coated glass substrate and characterized by XRD, FTIR and TEM for their structure and morphology. Dielectric behaviour of these composite films has been investigated in the very low frequency region to medium frequency region (1 kHz–1 MHz). The dielectric constant of the composite with 30% nanoparticles is almost one-tenth of the pure EB. The dielectric value becomes constant in the frequency region greater than 400 kHz. The change in dielectric behaviour of the composite is explained on the basis of multilayered interface formed between the ZnO nanoparticles and emeraldine chains. Nanoparticles have high energy surface which is responsible for the decrease of free volume for the orientation of polymer chains consequently decrease in dielectric constant of the composite. TEM images shows about 10 nm ZnO particles embedded in the emeraldine matrix. From the XRD data it has been observed that the lattice parameters of ZnO have been modified due to the alignment of polymer chains along the basal planes of the nanoparticles. The shift of N=Q=N and N–B–N vibration bands to higher wave number in IR indicates that interaction between emeraldine chain and nanoparticles which provides stability to emeraldine matrix.     

磁控溅射法制备的CaCu3Ti4O12薄膜

采用溅射方法成功地制备了CaCu3₃Ti4₄O12₁₂薄膜， 用原子力显微镜、x射线衍射（XRD）仪和LCR分析仪对样品进行形貌、物相结构和介电性质的研究.XRD表明，薄膜比块体的晶 格常数小但晶格畸变较大；LCR测量结果显示，在相同温度下薄膜比块体的相对介电常数低 ，薄膜相对介电常数由低到高转变时对应的温度较高且激活能较大.分析表明：薄膜的相对 介电常数较低是样品中晶相含量较低、缺陷较多使内部阻挡层电容大量减小、致密度不高引 起的；薄膜中 关键词： 磁控溅射 3Ti4₄O12₁₂')" href="#">CaCu3₃Ti4₄O12₁₂ 介电常 数 激活能     

Room temperature electrodeposition and characterization of bismuth ferric oxide (BFO) thin films from aqueous nitrate bath

Bismuth ferric oxide (BFO) thin films were prepared on fluorine doped tin oxide (FTO) coated glass substrates using electrodeposition method from aqueous nitrate bath at room temperature. The various preparative parameters, such as bath composition, current density, deposition time, etc were optimized to get good quality BFO thin films. The structural, surface morphological, optical and dielectrical properties of the films were studied using X-ray diffraction (XRD), scanning electron microscopy (SEM), optical absorption and dielectric measurement techniques. The results show that electrodeposition method allows to synthesis BFO films. The films are free from pinholes and cracks. The magnitudes of dielectric constant and loss tangent showed inverse frequency dependence.     

Effect of gamma-irradiation on the structural,optical and electrical properties of PEO/starch blend containing different concentrations of gold nanoparticles

ABSTRACT

Blend of polyethylene oxide (PEO)/starch (70/30 wt.%) filled with different amounts of gold nanoparticles (AuNPs) were prepared using the casting technique. X-ray diffraction (XRD) and Fourier-transform infrared (FTIR) techniques were used to investigate the structure of polymeric samples before and after exposing to gamma irradiation at different times. XRD showed a gradual decrease in intensity of crystalline peaks with increasing the gamma dose denotes a decrease in the amount of crystalline phase in the films, while the FTIR measurement shows induced changes in chemical structure assigned to the AuNPs amount and irradiation times. The optical energy gap values (E_g) for unirradiated and irradiated samples were calculated and interpreted. The differential scanning calorimetry (DSC) which showed the miscibility between the two components of the blend. The electrical conductivity (σ) measurement was showed increased in electrical conductivity after exposure to the gamma dose. The gold nanoparticles were used as nano?ller to improve the structural and electrical properties of polymeric samples. The results showed the Gamma irradiation significantly effect on the structural and electrical properties of PEO/starch blend.     

Spectral,thermal, optical and dielectric characterization of tris(tetraethylammonium) pentabromozincate(II) monohydrate crystals

Tris(tetraethylammonium) pentabromozincate(II) monohydrate, is a new semiorganic compound synthesized and crystallized by slow evaporation solution growth method at room temperature. The formation of the compound in the stoichiometric ratio was confirmed by elemental analysis. The crystalline nature of the compound was confirmed by powder X-ray diffraction method and the crystal system was found to be triclinic. The absorption spectrum of the compound shows absorption at 247 nm and it has wide transparency in the visible region. The lower cut-off wavelength and the optical transmittance window of the compound were identified by optical transmittance study. The thermogravimetric and differential thermal (TG–DTA) analyses were studied to find out the thermal stability of the synthesized compound. The thermal anomalies observed in the differential scanning calorimetry (DSC) analysis indicate that the compound shows a first order phase transition. The FTIR spectrum was used to characterize the various chemical bonds and water molecule present in the compound. The nonlinear optical property (NLO) of the material was analyzed by modified Kurtz–Perry powder technique and found that it has SHG efficiency three times greater than that of KDP. The dielectric constant and dielectric loss of the compound decrease with increase in frequency.     

Laser radiation effects on optical and structural properties of nanostructure CdSe thin film

Cadmium selenide (CdSe) thin films were deposited on a glass substrate using the thermal evaporation method at room temperature. The changes in the optical properties (optical band gap and absorption coefficient) after irradiation by TEA N₂ laser at different energies were measured in the wavelength range 190–800 nm using a spectrophotometer. It was found that the optical band gap is decreased after irradiating the thin films. The samples were characterized using X-ray diffraction (XRD), and the grain size of the CdSe thin film was calculated from XRD data, which was found to be 41.47 nm as-deposited. It was also found that grain size increases with laser exposure. The samples were characterized using a scanning electron microscope and it was found that big clusters were formed after irradiation by TEA N₂ laser.     

Thickness dependent optical dispersion parameters and nonlinear optical properties of nanostructured Cr doped CdO thin films

Cr doped CdO thin films were deposited on glass substrates by reactive DC magnetron sputtering with varying film thickness from 250 to 400 nm. XRD studies reveal that the films exhibit cubic structure with preferred orientation along the (2 0 0) plane. The optical transmittance of the films decreases from 92 to 72%, whereas the optical energy band gap of the films decreased from 2.88 to 2.78 eV with increasing film thickness. The Wemple–DiDomenico single oscillator model has been used to evaluate the optical dispersion parameters such as dispersion energy (E_d), oscillator energy (E_o), static refractive index (n_o) and high frequency dielectric constant (ε_∞). The nonlinear optical parameters such as optical susceptibility (χ⁽¹⁾), third order nonlinear optical susceptibility (χ⁽³⁾) and nonlinear refractive index (n₂) of the films were also determined.     

Some optical properties of amorphous and crystalline antimony trisulphide thin films

The change in optical properties accompanying the amorphous crystalline transition has been studied for antimony trisulphide thin films. The real and imaginary parts of the dielectric constant are found to be much lower for amorphous films at lower photon energies, possibly because of a large number of defect states which would mostly disturb the top of the valence band and the conduction band comprised, respectively, of chalcogen lone pair and antibonding states. The crystalline material shows some structure in the imaginary part of the dielectric constant that corresponds to interband transitions, and apparently the direct band edge is at 1.88 eV. In the edge region the power law absorption has been observed in the amorphous material from which the extrapolated optical gap has been found to be 1.7 eV.     

Influence of lithium potassium zirconate nanoparticles on the electrical properties and structural characteristics of poly(vinyl alcohol) films

We investigated the influence of lithium potassium zirconate (LiKZrO₃) nanoparticles on the electrical properties and structural characteristics of poly(vinyl alcohol) (PVA) films. PVA/LiKZrO₃ nanocomposite films were prepared by casting of aqueous solutions with varying LiKZrO₃ content (0.5, 1.0, and 2.0 wt.%). The dielectric constant (ε′), dielectric loss (ε″), AC conductivity (σ_ac), dielectric loss tangent (tan δ), and electric modulus (M′ and M″) of the nanocomposite films were measured over a range of frequencies at ambient temperature. The results show increases in σ_ac and M′ with frequency, whereas ε′, ε″, and tan δ decreased with increasing frequency. The films were also characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and X-ray diffraction (XRD) techniques. DSC and XRD revealed the nature of LiKZrO₃ nanoparticle interaction with the PVA matrix. TGA analysis revealed an increase in thermal stability of the nanocomposites with increasing nanoparticle concentration. Scanning electron microscopy confirmed uniform dispersion of LiKZrO₃ nanoparticles in the PVA matrix.     

Effect of gamma irradiation on HPMC/ZnO nanocomposite films

The present work looks into the structural, chemical, mechanical, optical and thermal modification in ZnO nanoparticle incorporated hydroxypropyl methylcellulose (HPMC) polymer films, induced by gamma irradiation. The irradiation process was performed in a gamma chamber at room temperature using Cobalt-60 source (average energy of 1.25?MeV) at different doses: 0, 50, 100, 150 and 200?kGy. The modifications in structural, chemical, mechanical, optical and thermal properties, due to gamma irradiation in HPMC/ZnO nanocomposite films, have been studied using wide angle X-ray scattering (XRD), Fourier transform infrared spectroscopy, universal testing machine, ultraviolet–visible spectrophotometry and thermogravimetric analysis. It is found that gamma irradiation improves the mechanical and thermal properties of nanocomposite films.     

Structural and optical analysis of 60Co gamma-irradiated thin films of polycrystalline Ga10Se85Sn5

The present study focuses on the effects of gamma irradiation on structural and optical properties of polycrystalline Ga₁₀Se₈₅Sn₅ thin films with a thickness of ～300?nm deposited by the thermal evaporation technique on cleaned glass substrates. X-ray diffraction patterns of the investigated thin films show that crystallite growth occurs in the orthorhombic phase structure. The surface study carried out by using the scanning electron microscope (SEM) confirms that the grain size increases with gamma irradiation. The optical parameters were estimated from optical transmission spectra data measured from a UV–vis-spectrophotometer in the wavelength range of 200–1100?nm. The refractive index dispersion data of the investigated thin films follow the single oscillator model. The estimated values of static refractive index n₀, oscillator strength E_d, zero frequency dielectric constant ε₀, optical conductivity σ_optical and the dissipation factor increases after irradiation, while the single oscillator energy E_o decreases after irradiation. It was found that the value of the optical band gap of the investigated thin films decreases and the corresponding absorption coefficient increases continuously with an increase in the dose of gamma irradiation. This post irradiation changes in the values of optical band gap and absorption coefficient were interpreted in terms of the bond distribution model.     

Effective dielectric constant model of electromagnetic backscattering from stratified air–sea surface film–sea water medium

Studies of surface film medium on the sea surface are carried out in this paper for developing the technology to automatically detect and classify sea surface films, and an effective dielectric constant model of electromagnetic backscattering from a stratified air–ocean interface. Numerical results of the new model show the characteristics of effective dielectric constants for the air–sea surface film–sea water medium as follows. The effective dielectric constants decrease with increasing relative dielectric constants of the sea surface films. The effective dielectric constants decrease in horizontal polarization(abbr. HH polarization) and increase in VV vertical polarization(abbr. VV polarization) with increasing radar incident angle. Effective dielectric constants vary with relative sea surface film thickness as a cosinusoidal function of sea surface film thickness. Effective dielectric constant of VV polarization is larger than that of HH polarization. Two potential applications are found with our model, i.e., the retrieval of dielectric constants from the sea surface film, and the film thickness retrieval with our model. Our model has a highly significant influence on improving the technology related to the remote sensing of sea surface films.     

Thermal,dielectric and conductivity studies on PVA/Ionic liquid [EMIM][EtSO4] based polymer electrolytes

Polymer electrolyte films of (PVA+15 wt% LiClO₄)+x wt% Ionic liquid (IL) 1-ethyl-3-methylimidazolium ethylsulfate [EMIM][EtSO₄] (x=0, 5, 10, 15) were prepared by solution cast technique. These films were characterized using TGA, DSC, XRD and ac impedance spectroscopic techniques. XRD result shows that amorphosity increases as the amount of the IL in PVA+salt (LiClO₄) is increased. DSC results confirm the same (except (PVA+15 wt% LiClO₄)+10 wt% IL). The dielectric and conductivity measurements were carried out on these films as a function of frequency and temperature. The addition of IL significantly improved the ionic conductivity of polymer electrolytes. Relaxation frequency vs. temperature plot for (PVA+15 wt% LiClO₄)+x wt% IL were found to follow an Arrhenius nature. The dielectric behavior was analyzed using real and imaginary parts of dielectric constant, dielectric loss tangent (tan δ) and electric modulus (M′ and M″).     

Dielectric relaxation and ac conductivity behavior of carboxyl functionalized multiwalled carbon nanotubes/poly (vinyl alcohol) composites

We study the dielectric relaxation and ac conductivity behavior of MWCNT-COOH/Polyvinyl alcohol nanocomposite films in the temperature (T) range 303–423 K and in the frequency (f) range 0.1 Hz–1 MHz. The dielectric constant increases with an increase in temperature and also with an increase in MWCNT-COOH loading into the polymer matrix, as a result of interfacial polarization. The permittivity data were found to fit well with the modified Cole-Cole equation. Temperature dependent values of the relaxation times, free charge carrier conductivity and space charge carrier conductivity were extracted from the equation. An observed increment in the ac conductivity for the nanocomposites was analysed by a Jonscher power law which suggests that the correlated barrier hopping is the dominant charge transport mechanism for the nanocomposite films. The electric modulus study revealed deviations from ideal Debye-type behavior which are explained by considering a generalized susceptibility function. XRD and DSC results show an increase in the degree of crystallinity.