Theoretical study on conformational conversion of 1,3-dioxane inside a capsular host

The conformational conversion of 1,3-dioxane guest encapsulated inside a cylindrical capsular host was investigated with PM3 method and single point energies were evaluated by B3LYP method. When entrapped in the capsule, the guest tumbles were slower than that in the free condition. The influences of the inner phase of the capsule on the guest conformational conversion were discussed in detail.     

Studies on Catalytic Conversion of Ethylene

FCC dry gas contains a large amount of ethylene.It is used by most of the refineries in China as fuel or simply burned in atmosphere.Few refineries make good use of the dry gas,so the precious ethylene resource in the dry gas is wasted.In this article,the possibility of catalytic conversion of ethylene to C_3,C_4,and some high molecular weight hydrocarbons in a fixed bed micro-reactor using LTB-1 catalyst,with pure ethylene as feedstock was studied.Effects of reaction temperature,reaction pressure,and feedstock flow rate,on the conversion of ethylene and the distribution of products were investigated to determine the proper reaction parameters to be used in practice.Good results indicate that this study may provide a new way of using the ethylene resource in the FCC dry gas.     

Synthesis of Star-like Polybutadienes by a Combination of Living Anionic Polymerization and “Click” Coupling Method

Three-arm and four-arm star-like polybutadienes(PBds) were synthesized via the combination of living anionic polymerization and the click coupling method. Kinetic study showed that the click reaction between the azido group terminated PBd-t-N3 and the alkyne-containing multifunctional linking reagent was fast and highly efficient. All coupling reactions were fully accomplished within 40 min at 50 °C in toluene in the presence of the reducing agent Cu(0), proven by 1H-NMR, FTIR and GPC measurements. For the coupling reactions between the PBd-t-N3 polymer and dialkyne-containing compound, the final conversion of the coupled PBd-PBd polymer was ca. 97.0%. When a PBd-t-N3 polymer was reacted with trialkyne-containing or tetraalkyne-containing compound, the conversion of three-arm or four-arm PBd was around 95.5% or 87.0%, respectively. Several factors influencing the coupling efficiency were studied, including the molecular weight of the initial PBd-t-N3, arm numbers and the molar ratio of the azido group to the alkynyl group. The results indicated that the conversion of the target products would be promoted when the molecular weight of the PBd-t-N3 was low and the molar ratio of the azido to alkynyl groups was close to 1.     

Toward high-efficiency perovskite solar cells with one-dimensional oriented nanostructured electron transport materials

The unique advantages of one-dimensional(1D) oriented nanostructures in light-trapping and chargetransport make them competitive candidates in photovoltaic(PV) devices. Since the emergence of perovskite solar cells(PSCs), 1D nanostructured electron transport materials(ETMs) have drawn tremendous interest. However, the power conversion efficiencies(PCEs) of these devices have always significantly lagged behind their mesoscopic and planar counterparts. High-efficiency PSCs with 1D ETMs showing eff...     

Non-Oxidative Aromatization of CH4-C_3H_8 over La-Promoted Zn/HZSM-5 Catalysts

The non-oxidative aromatization of mixed CH4 with C3H8 over La-promoted Zn/HZSM-5 catalysts was studied in a fixed-bed reactor at 823 K with space velocity 600 h-1 and CH4/C3H8 (mol ratio)=5:1. The propane conversion and the aromatic selectivities were up to 99% and 60% over the catalyst respectively, while methane conversion had an induction period with the highest conversion of 30%. The structure and surface acidity of the catalysts were characterized by XRD, NH3-TPD and TG-DTA. The influences of reaction and regenerative conditions on the activity and selectivity were also investigated.     

Kinetics of the Oxidative Dehydrogenation of Propane over a VMgO Catalyst

The reaction kinetics of the oxidative dehydrogenation of propane was studied at 475-550℃ over a VMgO catalyst. Vanadium-magnesium-oxides are among the most selective and active catalysts for the dehydrogenation of propane to propylene. Selectivity to propylene up to about 60% was obtained at 10% conversion, but the selectivity decreased with increasing conversion. No oxygenates were detected, the only by-products were CO and CO2. The reaction rate of propane was found to be first order in propane and close to zero order in oxygen, which is in agreement with a Mars van Krevelen mechanism with the activation of the hydrocarbon as the rate determining step. The activation energy of the conversion of propane was found to be 122±6 kJ/mol.     

Non-Oxidative Aromatization of CH4-C3H8 La-Promoted Zn/HZSM-5 Catalysts

The non-oxidative aromatization of mixed CH4 with C3H8 over La-promoted Zn/HZSM-5 catalysts was studied in a fixed-bed reactor at 823 K with space velocity 600 h^-1 and CH4/C3H8 （mol ratio）=5：l. The propane conversion and the aromatic selectivities were up to 99% and 60% over the catalyst respectively, while methane conversion had an induction period with the highest conversion of 30%. The structure and surface acidity of the catalysts were characterized by XRD, NH3-TPD and TG-DTA. The influences of reaction and regenerative conditions on the activity and selectivity were also investigated.     

Characterization and Activity of Cr, Cu and Ga Modified ZSM—5 for Direct Conversion of Methane to Liquid Hydrocarbons

Direct conversion of methane using a metal-loaded ZSM-5 zeolite prepared via acidic ion exchange was investigated to elucidate the roles of metal and acidity in the formation of liquid hydrocarbons. ZSM-5 (SiO2/A12O3=30) was loaded with different metals (Cr, Cu and Ga) according to the acidic ion-exchange method to produce metal-loaded ZSM-5 zeolite catalysts. XRD, NMR, FT-IR and N2 adsorption analyses indicated that Cr and Ga species managed to occupy the alllmlnum positions in the ZSM-5 framework. In addition, Cr species were deposited in the pores of the structure. However, Cu oxides were deposited on the surface and in the mesopores of the ZSM-5 zeolite. An acidity study using TPD-NH3, FT-IR, and IR-pyridine analyses revealed that the total number of acid sites and the strengths of the BrSusted and Lewis acid sites were significantly different after the acidic ion exchange treatment.Cu loaded HZSM-5 is a potential catalyst for direct conversion of methane to liquid hydrocarbons. The successful production of gasoline via the direct conversion of methane depends on the amount of aluminum in the zeolite framework and the strength of the BrSnsted acid sites.     

Synthesis of a Polymer-bound Sensitizer and its Application in the Photoisomerization of trans-Vitamin D_3 to cis-Vitamin D_3

The photochemistry of the vitamin D family and their precursors has been the subject of extensive studies for many years1-4. Most of the studies focus on the photoisomer- ization of 7-dehydrocholesterol and that of tachysterol to previtamin D3, which is of commercial importance in the synthesis of vitamin D34, 5. Recently the cis/trans isomerization of vitamin D analogs (Scheme 1) draws attention because of its importance in the synthesis of hydroxylated vitamin D metabolites6. However, o…     

Selective Oxidation of Propane by Lattice Oxygen of Vanadium-Phosphorous Oxide in a Pulse Reactor

Selective oxidation of propane by lattice oxygen of vanadium-phosphorus oxide (VPO) catalysts was investigated with a pulse reactor in which the oxidation of propane and the re-oxidation of catalyst were implemented alternately in the presence of water vapor. The principal products are acrylic acid (AA),acetic acid (HAc), and carbon oxides. In addition, small amounts of C1 and C2 hydrocarbons were also found, molar ratio of AA to HAc is 1.4-2.2. The active oxygen species are those adsorbed on catalyst surface firmly and/or bound to catalyst lattice, i.e. lattice oxygen; the selective oxidation of propane on VPO catalysts can be carried out in a circulating fluidized bed (CFB) riser reactor. For propane oxidation over VPO catalysts, the effects of reaction temperature in a pulse reactor were found almost the same as in a steady-state flow reactor. That is, as the reaction temperature increases, propane conversion and the amount of C1 C2 hydrocarbons in the product increase steadily, while selectivity to acrylic acid and to acetic acid increase prior to 350℃ then begin to drop at temperatures higher than 350℃, and yields of acrylic acid and of acetic acid attained maximum at about 400℃. The maximum yields of acrylic acid and of acetic acid for a single-pass are 7.50% and 4.59% respectively, with 38.2% propane conversion. When theamount of propane pulsed decreases or the amount of catalyst loaded increases, the conversion increases but the selectivity decreases. Increasing the flow rate of carrier gases causes the conversion pass through a minimum but selectivity and yields pass through a maximum. In a fixed bed reactor, it is hard to obtainhigh selectivity at a high reaction conversion due to the further degradation of acrylic acid and acetic acid even though propane was oxidized by the lattice oxygen. The catalytic performance can be improved inthe presence of excess propane. Propylene can be oxidized by lattice oxygen of VPO catalyst at 250℃, nevertheless, selectivity to AA and to HAc are even lower, much more acetic acid was produced (molar ratio of AA to HAc is 0.19:1-0.83:1) though the oxidation products are the same as from propane.     

Photosensitization of trans-Vitamin D3 to cis-Vitamin D3 in Heterogeneous System

Two modes of heterogeneous photoisomerization of trans-vitamin D3 to cis-vitamin D3 are described. The occurrence of isomerization on the substrate bounded to the polymeric support gives us the possibility in succession synthesis of 1α-hydroxyvitamin D3. The polymer-bound anthracene can sensitize isomerization of trans-vitamin D3 to cis-vitamin D3 efficiently and ease the separation process.     

Improved Performance of W／HZSM-5 Catalysts for Dehydroaromatization of Methane

The dehydroaramatization of methane over W-supported ZSM-5 with varying degrees of Li^ ion-exchanged catalysts was studied with and without oxygen at 1073 K and atmospheric pressure.Catalyst activity and stability were found to be influenced by the catalyst acidity related to BrSnsted acid sites and by the presence of oxygen in the feed. The NH3-TPD and FTIR-pyridine results demonstrated that partially exchanged of H^ ions by Li^ into the W/HZSM-5 catalysts could be used to control the amount of strong acid sites on the catalyst surface. Without oxygen, the 3WHLi-Z (5:1) catalyst that has strong acid sites equal to nearly 74% of the original strong acid sites in the parent HZSM-5 exhibited the highest methane conversion and selectivity towards aromatics. However, the catalyst deactivated in a five hour period. In the presence of oxygen, the catalyst activity and stability could be improved further.The results of this study revealed that a suitable amount of strong Bronsted acid sites as well as oxygen addition in the feed increased the catalyst activity and stability. The 3WHLi-Z(5:1) catalyst exhibited improved performance in the dehydroaromatization of methane.     

Proton Transfer Mechanism of Alanine Induced by Zn~（2＋）： a Theoretical Study

In this paper, proton transfer mechanism of alanine induced by Zn2+ was investiga- ted by the CCSD/6-31++G**//B3LYP/6-31++G** method. Six neutral complexes and one ampho- teric complex were optimized, among which the amphoteric complex was the most stable with binding energy of 201.92 kcal·mol-1. In addition, the rotation of intramolecular single bond leads to the neutral configuration conversion, in which the rotation energy barriers of C–C single bonds are lower than 10.51 kcal·mol-1, and those of C–O single bonds range among 9.53~17.50 kcal·mol-1. On the other hand, the proton transfers among the carboxylic oxygen atoms can also result in the neutral configuration conversion, whose energy barriers of forward/back reaction are 53.90 and 32.46 kcal·mol-1, respectively. In detail, the proton transfers from carboxylic group to amino lead to their configuration conversion from neutral to amphoteric. Furthermore, under the catalysis of Zn2+, there was no energy barrier in this reaction. The conversion route from the most stable neutral configuration Ⅱ to the most stable amphoteric configuration I was: Ⅱ→Ⅱ-Ⅲ→Ⅲ→Ⅲ-Ⅵ→Ⅵ→Ⅴ-Ⅵ→Ⅴ→Ⅰ-Ⅴ→Ⅰ,with the energy barrier to be 64.64 kcal·mol-1.     

Microwave-assisted reaction of peptide formation by amino acid with phosphate:Exploration of the most possible channels for the origin of life

The formation of peptides and then protein by small abiological molecules clusters such as amino acid is a key stage in the origin of life[1]. More and more ex- perimental results showed that phosphate plays an important role in the formation of biomolecules in prebiotic chemical evolution. The principal reservoirs of biochemical energy are phosphates (such as ATP). The peculiar role of phosphates in contemporary life might suggest its essential role in prebiotic energy conversion, syntheses …     

Kinetic Modeling of Plasma Methane Conversion Using Gliding Arc

Plasma methane (CH4) conversion in gliding arc discharge was examined. The result data of experiments regarding the performance of gliding arc discharge were presented in this paper. A simulation which is consisted some chemical kinetic mechanisms has been provided to analyze and describe the plasma process. The effect of total gas flow rate and input frequency refers to power consumption have been studied to evaluate the performance of gliding arc plasma system and the reaction mechanism of decomposition.Experiment results indicated that the maximum conversion of CH4 reached 50% at the total gas flow rate of 1 L/min. The plasma reaction was occurred at the atmospheric pressure and the main products were C (solid), hydrogen, and acetylene (C2H2). The plasma reaction of methane conversion was exothermic reaction which increased the product stream temperature around 30～50℃.     

Conversion of natural gas to C_2 hydrocarbons through dielectric-barrier discharge plasma catalysis

The experiments are carried out in the system of continuous flow reactors with dielectric-barrier discharge (DBD) for studies on the conversion of natural gas to C2 hydrocarbons through plasma catalysis under the atmosphere pressure and room temperature. The influence of discharge frequency, structure of electrode, discharge voltage, number of electrode, ratio of H2/CH4, flow rate and catalyst on conversion of methane and selectivity of C2 hydrocarbons are investigated. At the same time, the reaction process is investigated. Higher conversion of methane and selectivity of C2 hydrocarbons are achieved and deposited carbons are eliminated by proper choice of parameters. The appropriate operation parameters in dielectric-barrier discharge plasma field are that the supply voltage is 20-40 kV (8.4-40 W), the frequency of power supply is 20 kHz, the structure of (b) electrode is suitable, and the flow of methane is 20-60 ml · min-1. The conversion of methane can reach 45%, the selectivity of C2 hydrocarbons i     

Homopolymerization of N-pyrimidinyl acrylamide

Homopolymerization of N-pyrimidinyl acrylamide(NPA)was reported for the first time.The polymer(polyNPA)was soluble only in acidic media and fluoroalcohols,and only in fluoroalcohol was homogeneous polymerization of NPA feasible.~1H NMR analysis proved that a 1:1 H-bonding complex could be formed between NPA andα,α-bis(trifluoromethyl)phenyl propan-2-ol (BTMP).Cumyl dithiobenzoate mediated reversible addition-fragmentation chain transfer(RAFT)polymerization of NPA in BTMP was carried out.~1H NMR analyses proved that the molecular weight increased linearly with the monomer conversion.The polymer prepared in conventional solvents was atactic while in protic media the syndiotacticity was slightly enhanced.     

Two Chiral Building Blocks for the Stereocontrolled Synthesis of Anti-and Syn-1,3-Diols

During the last decade, chiral building blocks for 1, 3-diols of various configurations have been synthesized and applied widely in the total synthesis of natural polyene macrolide antibiotics1 and 1(, 25-dihydroxyvitamin D3 analogues2,3. The synthesis of the building block has attracted much interest in recent years. Herein, we report the synthesis of two chiral building blocks 1 and 2 in 8 steps and 7 steps respectively, starting from the readily available and inexpensive D (+)-xylose 3 as o…     

Promotional Effect of Bismuth as Dopant in Bi-Doped Vanadyl Pyrophosphate Catalysts for Selective Oxidation of n-Butane to Maleic Anhydride

Bismuth-promoted (1% and 3%) vanadyl pyrophosphate catalysts were prepared by refluxing Bi(NO3)3·5H2O and VOPO4·2H2O in isobutanol. The incorporation of Bi into the catalysts lattice increased the surface area and lowered the overall V oxidation state. Profiles of temperature programmed reduction (TPR) in H2 show a significant shift of the maxima of major reduction peaks to lower temperatures for the Bi-promoted catalysts. A new peak was also observed at the low temperature region for the catalyst with 3% of Bi dopant. The addition of Bi also increased the total amount of oxygen removed from the catalysts. The reduction pattern and reactivity information provide fundamental insight into the catalytic properties of the catalysts. Bi-promoted catalysts were found to be highly active (71% and 81% conversion for 1% and 3% Bi promoted catalysts, respectively, at 703 K), as compared to the unpromoted material (47% conversion). The higher activity of the Bi-promoted catalysts is due to that these catalysts possess highly active and labile lattice oxygen. The better catalytic performance can also be attributed to the larger surface area.