High melting thermoplastic/epoxy resin blends: Influence of the curing reaction on the crystallization and melting behavior

The influence of the cure process and the resulting reaction‐induced phase separation (RIPS) on the crystallization and melting behavior of polyoxymethylene (POM) in epoxy resin diglycidylether of bisphenol A (DGEBA) blends has been studied at different cure temperatures (180 and 145 °C). The crystallization and melting behavior of POM was studied with DSC and the simultaneous blend morphology changes were studied using OM. At first, the influence of the epoxy monomer on the dynamically crystallized POM was investigated. Secondly, a cure temperature above the melting point of POM (T_cure = 180 °C) was applied for blends with curing agent to study the influence of resulting phase morphology types on the crystallization behavior of POM in the epoxy blends. Large differences between particle/matrix and phase‐inverted structures have been observed. Thirdly, the cure temperature was lowered below the melting temperature of POM, inducing isothermal crystallization prior to RIPS. As a consequence, a distinction was made between dynamically and isothermally crystallized POM. Concerning the dynamically crystallized material, a clear difference could be made between the material crystallized in the homogeneous sample and that crystallized in the phase‐separated structures. The isothermally crystallized POM was to a large extent influenced by the conversion degree of the epoxy resin. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2456–2469, 2007     

Ringed spherulites in ternary polymer blends of poly(<Emphasis Type="Italic">ε</Emphasis>-caprolactone), poly(styrene-<Emphasis Type="Italic">co</Emphasis>-acrylonitrile), and polymethacrylate

The relationship between ringed spherulite morphology, crystallization regimes/kinetics, and molecular interactions in miscible ternary blends of poly(-caprolactone) (PCL), poly(benzyl methacrylate) (PBzMA), and poly(styrene-co-acrylonitrile) (SAN) was investigated by using differential scanning calorimetry (DSC), polarized optical microscopy (POM), and wide-angle X-ray diffraction (WAXD). The interactions resulted in the deviation of both experimental and calculated T_gs and formation of the specific morphology of the spherulitic structure. Ring-banded spherulites were observed in the PCL/PBzMA/SAN ternary blends. The width of ring bands changed with the blend ratio and the crystallization temperature. Additionally, both composition and wt% of AN in the SAN copolymer had an apparent effect on the morphology of PCL spherulites. Both the crystallization structure of lamellae and molecular interactions greatly influenced the ring bands of PCL spherulites. Furthermore, by using the Flory–Huggins approximation, the depression of the melting point showed that interactions in the PCL/PBzMA/SAN-17 blend were greater than in the PCL/PBzMA/SAN-25 blend. In the ternary blends, the great molecular interactions between amorphous and crystalline polymer resulted in better homogeneity and a larger band period of the extinction rings in the PCL spherulites.     

Phase behavior,crystallization, and morphology in thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin and poly(ϵ‐caprolactone)

Thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin (PEG‐ER) and poly(?‐caprolactone) (PCL) were prepared via an in situ curing reaction of poly(ethylene glycol) diglycidyl ether (PEGDGE) and maleic anhydride (MAH) in the presence of PCL. The miscibility, phase behavior, crystallization, and morphology of these blends were investigated. The uncured PCL/PEGDGE blends were miscible, mainly because of the entropic contribution, as the molecular weight of PEGDGE was very low. The crystallization and melting behavior of both PCL and the poly(ethylene glycol) (PEG) segment of PEGDGE were less affected in the uncured PCL/PEGDGE blends because of the very close glass‐transition temperatures of PCL and PEGDGE. However, the cured PCL/PEG‐ER blends were immiscible and exhibited two separate glass transitions, as revealed by differential scanning calorimetry and dynamic mechanical analysis. There existed two phases in the cured PCL/PEG‐ER blends, that is, a PCL‐rich phase and a PEG‐ER crosslinked phase composed of an MAH‐cured PEGDGE network. The crystallization of PCL was slightly enhanced in the cured blends because of the phase‐separated nature; meanwhile, the PEG segment was highly restricted in the crosslinked network and was noncrystallizable in the cured blends. The phase structure and morphology of the cured PCL/PEG‐ER blends were examined with scanning electron microscopy; a variety of phase morphologies were observed that depended on the blend composition. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2833–2843, 2004     

Thermal behavior and phase behavior in blends of liquid crystalline poly(aryl ether ketone) and poly(aryl ether ether ketone) containing thioether units

Thermal behavior and phase behavior in blends of liquid crystalline poly(aryl ether ketone) with lateral methoxy groups (M-PAEK) and poly(aryl ether ether ketone) containing thioether units (S-PEEK) have been investigated by differential scanning calorimetry (DSC) and polarized light microscopy (PLM) techniques. The results indicate that the composition of the blends has great effect on the phase behavior and morphology. Thin films of pure M-PAEK and S-PEEK crystallized from the melts exhibit typical mosaic and spherulitic structures, respectively. For the blends with higher M-PAEK contents (> 50%), an unusual ring-banded spherulite with structural discontinuity is formed. The bright core and rings of the ring-banded spherulites under PLM are composed of M-PAEK phase, while the dark rings consist mainly of S-PEEK phase. For the 50:50 M-PAEK/S-PEEK blend, the ring-banded spherulites and S-PEEK spherulites coexist, which implies that a partial phase separation between the two components takes place in the melting state. In S-PEEK-rich blends, a volume-filled spherulite is produced. In addition, the effect of isothermal crystallization temperature on the phase behavior, especially the ring-banded spherulite formation in the blends, is discussed.     

Replicated Banded Spherulite: Microscopic Lamellar-assembly of Poly(L-lactic acid) Crystals in the Poly(oxymethylene) Crystal Framework

The morphologies of poly(L-lactic acid) (PLLA) spherulites,when crystallized within the pre-existed poly(oxymethylene)(POM) crystal frameworks,have been investigated.PLLA/POM blend is a melt-miscible crystalline/crystalline blend system.Owing to the lower melting point but much faster crystallization rate than PLLA,POM crystallized first upon cooling from the melt state and then melted first during the subsequent heating process in this blend system.Lamellar assembly of PLLA crystals within the pre-existed POM spherulitic frameworks was directly observed with the polarized light microscopy by selectively melting the POM frameworks.The investigation indicated that PLLA crystals fully replicated the spherulitic morphology and optical birefringence of the POM crystal frameworks,which was independent of Tc.On the other hand,POM could also duplicate the pre-existed PLLA morphologies.The result obtained provides us a possibility to design the lamellar assembly and crystal structures of polymer crystals in miscible crystalline/crystalline polymer blends.     

聚己内酯在聚己内酯/聚乙烯基甲基醚共混体系中的结晶研究

通过示差扫描量热(DSC)、广角X射线衍射(WAXD)、小角X射线散射(SAXS)研究了聚己内酯(PCL)/聚乙烯基甲基醚(PVME)共混体系中PCL的结晶行为.研究结果表明,共混聚合物中PCL的结晶度几乎不随体系的组成而发生变化.共混物中PVME的存在没有改变PCL的晶体结构,但是随着PVME含量的增加,片晶之间的距离则大,这主要是由于非晶层增厚引起的.     

聚β—羟基丁酯酯／超高分子量聚氧化乙烯共混体系相容性和结晶行为

为了解决废弃塑料引起的“白色污染”问题,世界各国竞相研制开发可生物降解高分子材料,其中,有关聚β羟基丁酸酯［ｐｏｌｙ（βｈｙｄｒｏｘｙｂｕｔｙｒａｔｅ）（ＰＨＢ）］的研究尤其活跃．然而,由于商品价格较高,材料本身抗冲击性能较差、加工窗口较窄等限制...     

聚β-羟基丁酸酯/超高分子量聚氧化乙烯共混体系相容性和结晶行为

为了解决废弃塑料引起的“白色污染”问题,世界各国竞相研制开发可生物降解高分子材料,其中,有关聚β 羟基丁酸酯［ｐｏｌｙ（β ｈｙｄｒｏｘｙｂｕｔｙｒａｔｅ）（ＰＨＢ）］的研究尤其活跃．然而,由于商品价格较高,材料本身抗冲击性能较差、加工窗口较窄等限制...     

Eutectic crystallization and hydrogen bonding interactions in polymer/surfactant blends

The unusual eutectic crystallization behavior in the poly(ε‐caprolactone) (PCL) and 3‐pentadecylphonel (PDP) binary blends was investigated by differential scanning calorimetry and Fourier transform infrared (FTIR) spectroscopy. A eutectic system was found with the eutectic composition at 60 wt % PDP and the eutectic melting temperature at 35 °C. The melting process of the blend at the eutectic composition was studied by in situ FTIR. The concurrence of the melting of PCL and PDP crystallites and the sequential formation of hydrogen bonding interaction between PDP molecules and PCL chains were traced. It was also found that a further increase in temperature above the eutectic melting temperature would impair the hydrogen bonding and increase the content of nonassociated phenol hydroxyl group. The semicrystalline morphology of blends affected by the composition was also investigated. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1015–1023, 2009     

Effects of miscible diluent of poly(ether imide) on ring-banded morphology of poly(trimethylene terephthalate)

The melting, crystallization, and self-packed ring patterns in the spherulites of miscible blends comprising poly(trimethylene terephthalate) (PTT) and poly(ether imide) (PEI) were revealed by optical, scanning electron microscopies (PLM and SEM) and differential scanning calorimetry (DSC). Morphology and melting behavior of the miscible PTT/PEI blends were compared with the neat PTT. Ringed spherulites appeared in the miscible PTT/PEI blends at all crystallization temperatures up to 220 °C, whereas at this high temperature no rings were seen in the neat PTT. A postulation was proposed, and interrelations between rings in spherulites and the multiple lamellae distributions were investigated. The specific interactions and the segregation of amorphous PEI were discussed for interpreting the morphological changes of 220 °C-melt-crystallized PTT/PEI samples. Interlamellar segregation of PEI might be associated with multiple lamellae in the spherulites of PTT/PEI blends; therefore, rings were more easily formed in the PTT/PEI blends at all crystallization temperatures. A postulated model of uneven lamellar growth, coupled with periodical spiraling, more properly describes the possible origin of ring bands from combined effects of both interactions and segregation between the amorphous PEI and PTT in blends.     

Effects of amorphous poly(vinyl acetate) on crystalline morphology of poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid)

The amorphous and crystalline phase behavior, spherulite morphology, and interactions between amorphous poly(vinyl acetate) (PVAc) and poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid) (PHBV) were examined using differential scanning calorimetry, polarized-light optical and scanning electron, atomic-force microscopy (DSC, POM, SEM, AFM), and small-angle X-ray scattering (SAXS). The PHBV/PVAc blend was found to be miscible with an almost linear T _g-composition relationship, indicating perfect homogeneity. Interaction parameter by melting point depression is a negative value of χ = −0.32, suggesting quite favorable interaction strength. With the intimate interaction between the amorphous PVAc and crystalline PHBV polymers, effects of PVAc on the spherulitic morphology of PHBV are quite significant. Owing to the higher T _g of PVAc (than that of PHBV), the spherulite growth rate of PHBV was depressed by increasing PVAc content in blends. Neat PHBV exhibits ring-banded spherulites when crystallized at T_c = 60 ~ 110^° C {T_{\rm{c}}} = {6}0\sim {11}0^\circ {\hbox{C}} ; however, with increasing PVAc content in the blends, the temperature range at which the PHBV/PVAc blends exhibit ring-banded spherulites remains similar but the regularity increases, and the inter-ring spacing significantly decreases. In addition, the spherulite size and ring-band patterns therein are strongly dependent on T _max (190 vs. 220 °C, respectively, for erasing prior nuclei), from which the blends were quenched to a T _c (60–110 °C) for crystallization. For PHBV/PVAc blends crystallized at the same T _c from different T _max, higher T _max tends to erase nuclei, leading to larger spherulites. However, such larger spherulites owing to higher T _max are not necessarily packed with thicker lamellae.     

聚左旋乳酸/聚消旋乳酸共混物的结晶行为

非晶态聚消旋乳酸(PDLLA)对PLLA的结晶行为有较大的影响。本文利用差示扫描量热仪(DSC)和偏光显微镜(POM)对不同分子量PLLA、PDLLA按不同比例制得的共混物结晶进行了系统研究。结果表明随PDLLA含量的增大PLLA冷结晶温度升高,且越接近熔融温度。PDLLA分子量较小时PLLA球晶特征被明显破坏,PDLLA分子量较大时PLLA更易形保持球晶特征且易形成环带球晶形貌,这与结晶速率与非晶组分的扩散速率匹配程度有关。低分子量的PDLLA使PLLA的最大生长速率对应的温度出现在较低温度。     

Influence of microcrystalline cellulose fiber (MCCF) on the morphology of poly(3-hydroxybutyrate) (PHB)

Biopolymer composites were prepared from poly(3-hydroxybutyrate) (PHB)/microcrystalline cellulose fiber (MCCF)/plastiziers/poly(vinyl acetate) by melt extrusion. The morphology, crystal structure, and non-isothermal crystallization of these composites were investigated by polarized optical microscopy (POM), differential scanning calorimetry, Fourier transform infrared spectrometer, and wide-angle X-ray diffraction. The results of DSC indicate that the addition of small amount of MCCF improved the crystallization rate. Non-isothermal crystallization shows that the composites 1 and 2 have lower crystallization half time (t _{0 .5}) than that of pure PHB. Higher MCCF contents in PHB (composite 4) lead to a decrease in the crystallization rate. POM micrographs show that the MCCF were well dispersed in the PHB matrix and served as a nucleating agent with a strong change in PHB morphology. Increasing the isothermal crystallization temperature above 120 °C, leads to the formation of banded spherulites with large regular band spacing. Decreasing the isothermal crystallization temperature below 100 °C produces more and small spherulites.     

Complex phase behavior and state of miscibility in Poly(ethylene glycol)/Poly(l‐lactide‐co‐ε‐caprolactone) Blends

A miscibility and phase behavior study was conducted on poly(ethylene glycol) (PEG)/poly(l ‐lactide‐ε‐caprolactone) (PLA‐co‐CL) blends. A single glass transition evolution was determined by differential scanning calorimetry initially suggesting a miscible system; however, the unusual T_g bias and subsequent morphological study conducted by polarized light optical microscopy (PLOM) and atomic force microscopy (AFM) evidenced a phase separated system for the whole range of blend compositions. PEG spherulites were found in all blends except for the PEG/PLA‐co‐CL 20/80 composition, with no interference of the comonomer in the melting point of PEG (T_m = 64 °C) and only a small one in crystallinity fraction (X_c = 80% vs. 70%). However, a clear continuous decrease in PEG spherulites growth rate (G) with increasing PLA‐co‐CL content was determined in the blends isothermally crystallized at 37 °C, G being 37 µm/min for the neat PEG and 12 µm/min for the 20 wt % PLA‐co‐CL blend. The kinetics interference in crystal growth rate of PEG suggests a diluting effect of the PLA‐co‐CL in the blends; further, PLOM and AFM provided unequivocal evidence of the interfering effect of PLA‐co‐CL on PEG crystal morphology, demonstrating imperfect crystallization in blends with interfibrillar location of the diluting amorphous component. Significantly, AFM images provided also evidence of amorphous phase separation between PEG and PLA‐co‐CL. A true T_g vs. composition diagram is proposed on the basis of the AFM analysis for phase separated PEG/PLA‐co‐CL blends revealing the existence of a second PLA‐co‐CL rich phase. According to the partial miscibility established by AFM analysis, PEG and PLA‐co‐CL rich phases, depending on blend composition, contain respectively an amount of the minority component leading to a system presenting, for every composition, two T_g's that are different of those of pure components. © 2013 Wiley Periodicals, Inc. J. Polym. Sci. Part B: Polym. Phys. 2014 , 52, 111–121     

Crystallization,morphology, and thermal behavior of poly(p‐phenylene sulfide)

This article deals with the structure, crystallization, morphology, and thermal behavior of poly(p‐phenylene sulfide) (PPS) with low‐molecular mass, probed by DSC, optical, and electron microscopy. The growth rates of spherulites were measured over the temperature range 235–275°C. A regime II–III transition was found at T = 250°C. The regime transition was accompanied by a morphological change from sheaflike structure to classical spherulites. The Avrami equation poorly described the isothermal crystallization of PPS, for the occurrence of mixed growth mechanisms and secondary crystallization, in agreement with the morphology and the thermal behavior. Two melting peaks were detected on DSC curves and attributed to the melting of crystals formed isothermally at T_c by primary and secondary crystallization. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 415–424, 2001     

Analysis of Polymorphism and Dual Crystalline Morphologies in Poly(hexamethylene terephthalate)

Summary: The polymorphisms in poly(hexamethylene terephthalate) (PHT), along with their associated melting and spherulite morphologies, were examined by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD), and polarized‐light microscopy (PLM). The morphology and crystal cells were dependent on the temperature of crystallization. When melt‐crystallized at low temperatures (90–135 °C), PHT showed at least five melting peaks and two re‐crystallization peaks upon DSC scanning, and the samples displayed various fractions of both α and β crystals. However, only a single melting peak was obtained in PHT melt‐crystallized at 140 °C or above, which displayed a single type of β crystal. In addition, two different forms of spherulites were identified in melt‐crystallized PHT, with one being a typical Maltese‐cross spherulite containing the α crystal, and the other being a dendrite‐type packed mainly with the β crystal. This study provides timely evidence for a critical interpretation of the relationship between multiple melting and polymorphisms (unit cells and spherulites) in polymers, including semi‐crystalline polyesters.

WAXD diffractograms for PHT melt‐crystallized at 140 °C, revealing a single type of β‐crystal cell.     

The effects of melt annealing and counterpart's molecular weight on the thermal properties and phase morphology of poly(L‐lactide)‐based blends

The thermal properties and phase morphology of poly(L ‐lactide) (PLLA)‐based blends have been studied. Two poly(ethylene glycol)s (PEGs) with molecular weight (MW) of about 1,500 (1.5k) g/mol and 2,000,000 (2M) g/mol, respectively, were used as counterparts. The blends were annealed at a preselected temperature of 200 °C for either 2 min or 30 min before the characterizations. Both PEGs were determined to enhance the crystallizability of PLLA. After a 2‐min process of annealing, the PEG(1.5k)'s crystallization efficiency on PLLA has been noted to increase with the increase of its content. Conversely, PEG(2M)'s crystallization efficiency declined with the increase of its content. Extending the annealing time has evidently changed the PEGs' crystallization effect on PLLA. Moreover, the PEG(1.5k) has, to a greater extent, brought about the depression of PLLA's melting temperature by increasing its content, and this depression increased with the annealing time. The blends exhibited lower thermal stability than those of the parent components, particularly for the PEG(1.5k)‐included system with a higher PEG content. Regardless of the annealing time, the PEG(1.5k)‐included blends have shown homogeneous melt morphology under light microscope, whereas the PEG(2M)‐included blends have displayed phase‐separated melt morphology. In addition to the composition, PEG's MW and annealing time influence the crystalline morphology of the blends. The ringed PLLA spherulites have appeared mostly in the 2‐min annealed PEG(1.5k)‐included blends. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1497–1510, 2009     

Crystallization behavior and morphology of poly(butylene succinate) modified with rosin maleopimaric acid anhydride

The melting behavior, crystallization behavior, and morphology of PBSR, which is Poly(butylene succinate) modified with rosin maleopimaric acid anhydride (RMA), were investigated with differential scanning calorimetry (DSC) and polarized optical microscope (POM). The multiple endotherms were ascribed to the recrystallization during DSC measurement and the equilibrium melting temperature determined by the Peak L, which was associated with the fusion of the crystals grown by normal primary crystallization, was 125.9 °C. After the kinetic parameters for isothermal crystallization of PBSR were determined by Avrami equation, to make a detailed regime transition analysis, the well‐established Lauritzen–Hoffman equation was employed. The results indicated that there were two regimes, regime II and regime III, in the range of higher and lower crystallization temperature, respectively. The regime transition temperature is about 81 °C. At last, the spherulitic morphologies of PBSR after being crystallized isothermally at different temperature were observed with the help of POM. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2694–2704, 2005     

改性羟基磷灰石/聚乳酸纳米复合材料的结晶行为

利用溶剂复合的方法制备了具有良好生物相容性的表面接枝聚(γ-苄基-L-谷氨酸)的改性羟基磷灰石/聚乳酸纳米复合材料, 并研究了其熔融与结晶行为. 结果表明, 聚乳酸的玻璃化转变温度为60.3 ℃, 而复合材料的玻璃化转变温度达到65.8 ℃, 不同样品在140 ℃等温结晶后, 改性羟基磷灰石/聚乳酸复合材料的球晶直径仅为聚乳酸(PLLA)球晶直径的16.7%~66.7%. 复合材料的熔点提高到184.4 ℃.     

Crystallization kinetics and morphology of biodegradable poly(butylene succinate‐co‐propylene succinate)s

The crystallization behavior of biodegradable poly(butylene succinate) and copolyesters poly(butylene succinate‐co‐propylene succinate)s (PBSPS) was investigated by using ¹H NMR, DSC and POM, respectively. Isothermal crystallization kinetics of the polyesters has been analyzed by the Avrami equation. The 2.2‐2.8 range of Avrami exponential n indicated that the crystallization mechanism was a heterogeneous nucleation with spherical growth geometry in the crystallization process of polyesters. Multiple melting peaks were observed during heating process after isothermal crystallization, and it could be explained by the melting and recrystallization model. PBSPS was identified to have the same crystal structure with that of PBS by using wide‐angle X‐ray diffraction (WAXD), suggesting that only BS unit crystallized while the PS unit was in an amorphous state. The crystal structure of polyesters was not affected by the crystallization temperatures, too. Besides the normal extinction crosses under the POM, the double‐banded extinction patterns with periodic distance along the radial direction were also observed in the spherulites of PBS and PBSPS. The morphology of spherulites strongly depended on the crystallization temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 420–428, 2007