Properties of Ge-doped,high-quality bulk GaN crystals fabricated by hydride vapor phase epitaxy

We investigated the properties of Ge-doped, high-quality bulk GaN crystals with Ge concentrations up to 2.4×10¹⁹ cm⁻³. The Ge-doped crystals were fabricated by hydride vapor phase epitaxy with GeCl₄ as the dopant source. Cathodoluminescence imaging revealed no increase in the dislocation density at even the highest Ge concentration, with values as low as 3.4×10⁶ cm⁻². The carrier concentration, as determined by Hall measurement, was almost identical to the combined concentration of Ge and unintentionally incorporated Si. The electron mobilities were 260 and 146 cm² V⁻¹ s⁻¹ for n=3.3×10¹⁸ and 3.35×10¹⁹ cm⁻³, respectively; these values are markedly larger than those reported in the past for Ge-doped GaN thin films. The optical absorption coefficient was quite small below the band gap energy; it slightly increased with increase in Ge concentration. Thermal conductivity, estimated by the laser-flash method, was virtually independent of Ge concentration, maintaining an excellent value around 2.0 W cm⁻¹ K⁻¹. Thermal expansion coefficients along the a- and m-axes were approximately constant at 5.0×10⁻⁶ K⁻¹ in the measured doping concentration range.     

Template free-solvothermaly synthesized copper selenide (CuSe,Cu2−xSe, β-Cu2Se and Cu2Se) hexagonal nanoplates from different precursors at low temperature

Nonstoichiometric (Cu_2−xSe) and stoichiometric (CuSe, β-Cu₂Se and Cu₂Se) copper selenide hexagonal nanoplates have been synthesized using different general and convenient copper sources, e.g. copper chloride, copper sulphate, copper nitrate, copper acetate, elemental copper with elemental selenium, friendly ethylene glycol and hydrazine hydrate in a defined amount of water at 100 °C within 12 h adopting the solvothermal method. Phase analysis, purity and morphology of the product have been well studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM) and energy dispersive X-ray diffraction (EDAX) techniques. The structural and compositional analysis revealed that the products were of pure phase with corresponding atomic ratios. SEM, TEM and HRTEM analyses revealed that the nanoplates were in the range 200–450 nm and the as-prepared products were uniform and highly crystallized. The nanoplates consisted of {0 0 1} facets of top–bottom surfaces and {1 1 0} facets of the other six side surfaces. This new approach encompasses many advantages over the conventional solvothermal method in terms of product quality (better morphology control with high yield) and reaction conditions (lower temperatures). Copper selenide hexagonal nanoplates obtained by the described method could be potential building blocks to construct functional devices and solar cell. This work may open up a new rationale on designing the solution synthesis of nanostructures for materials possessing similar intrinsic crystal symmetry. On the basis of the carefully controlled experiments mentioned herein, a plausible formation mechanism of the hexagonal nanoplates was suggested and discussed. To the best of our knowledge, this is the first report on nonstoichiometric (Cu_2−xSe) as well as stoichiometric (CuSe, β-Cu₂Se and Cu₂Se) copper selenide hexagonal nanoplates with such full control of morphologies and phases by this method under mild conditions.     

Droplet epitaxy of zinc-blende GaN quantum dots

Zinc-blende GaN quantum dots were grown on 3C-AlN(0 0 1) by a vapor–liquid–solid process in a molecular beam epitaxy system. We were able to control the density of the quantum dots in a range of 5×10⁸–5×10¹² cm⁻². Photoluminescence spectroscopy confirmed the optical activity of the GaN quantum dots in a range of 10¹¹–5×10¹² cm⁻². The data obtained give an insight to the condensation mechanism of the vapor–liquid–solid process in general, because the GaN quantum dots condense in metastable zinc-blende crystal structure supplied by the substrate, and not in the wurtzite crystal structure expected from free condensation in the droplet.     

Kinetics of (R,S)- and (R)-mandelic acid in an unseeded cooling batch crystallizer

The objective of this work is to determine the nucleation and growth kinetics of (R,S)-mandelic acid ((R,S)-MA) and (R)-mandelic acid ((R)-MA) in aqueous solutions using an unseeded cooling crystallization process. To obtain the nucleation and growth kinetics, the solubility, metastable zone limits, and supersaturation were measured by in-situ attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy and focused beam reflectance measurement (FBRM). The nucleation rate and growth rate parameters were determined by a nonlinear optimization algorithm. The effects of initial concentration and cooling rate on supersaturation and the nucleation rate are also discussed.     

Preparation,crystal structure,spectrographic characterization,thermal and third order nonlinear optical properties of benzyltriethylamine bis(2-thioxo-1,3-dithiole-4,5-dithiolato)nickel(III)

The preparation and crystal structure of a novel nonlinear optical organometallic crystal, benzyltriethylamine bis(2-thioxo-1,3-dithiole-4,5-dithiolato)nickel(III) (BTEANDT), are described. The crystal was characterized by elemental analyses, infrared and X-ray powder diffraction spectroscopy, thermal analysis and optical absorption. The third order nonlinear optical properties of crystal were investigated by using the Z-scan technique at 1064 nm with 20 ps. A self-focusing effect and a saturable absorption were observed. The nonlinear refraction coefficient (n₂) and the nonlinear absorption coefficient (β) have been found to be 7.311×10⁻¹⁸ m²/W and −6.064×10⁻¹¹ m/W when the on-axis irradiance at focus (I₀) is 3.025 GW/cm². The relationship between β and I₀ was studied, which has revealed that the former is proportional to the latter. The result has been explained with the theory of absorption cross-section.     

The mechanism of the formation of enantiotropic polymorphs of carisbamate in solution crystallization

The nucleation kinetics, as a function of supersaturation level, was studied for carisbamate, a polymorphic crystalline compound, in methanol, ethanol, 2-propanol and water. The induction times in nucleation kinetics varied markedly with respect to relative supersaturation in the range 1.3–2.3. At the same relative supersaturation, the induction time for carisbamate in methanol is the shortest, increasing in order from ethanol, 2-propanol, and then water. The interfacial tensions γ between carisbamate and methanol, ethanol, 2-propanol, and water were estimated from their induction times based on nucleation theory and were found to be about 3.6, 4.1, 4.5, and 5.7 mJ/m², respectively. These values were of same order of magnitude as those obtained from solubility data. The equation that displays the influence of interfacial tension, supersaturation and temperature on crystallization kinetics was derived, and found to be consistent with experimental observations. The mechanism of enantiotropic polymorphism for carisbamate in the solvents is illustrated. Using interfacial tension values determined for single solvents, the polymorphic form resulting from crystallization in mixed and pure solvent systems could be predicted with good accuracy.     

Structural,electrical and optical properties of SnO2 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

SnO₂ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates at different substrate temperatures (500–800 °C) by metalorganic chemical vapor deposition (MOCVD). Structural, electrical and optical properties of the films have been investigated. The films deposited at 500 and 600 °C are epitaxial SnO₂ films with orthorhombic columbite structure, and the HRTEM analysis shows a clear epitaxial relationship of columbite SnO₂(1 0 0)||YSZ(1 0 0). The films deposited at 700 and 800 °C have mixed-phase structures of rutile and columbite SnO₂. The carrier concentration of the films is in the range from 1.15×10¹⁹ to 2.68×10¹⁹ cm⁻³, and the resistivity is from 2.48×10⁻² to 1.16×10⁻² Ω cm. The absolute average transmittance of the films in the visible range exceeds 90%. The band gap of the obtained SnO₂ films is about 3.75–3.87 eV.     

Simulation of metastable zone width and induction time for a seeded aqueous solution of potassium sulfate

The metastable zone width (MSZW, ΔT_m) and induction time (t_ind) were determined with computer simulation for seeded batch crystallization of potassium sulfate from aqueous solution. The MSZW and induction time determined with simulation showed the same behavior as experimental values reported in the literature; log (ΔT_m) increased linearly with an increase in log R (R: cooling rate) and t_ind decreases in proportion to (ΔT)⁻ⁿ (ΔT: supercooling, n: nucleation order in the secondary rate expression of B=k_n(ΔT)ⁿ). The secondary nucleation parameters (k_n and n) were deduced both from the simulated MSZW and induction times by using the previously proposed model [J. Cryst. Growth, 2010, 312, 548–554]. The secondary nucleation rate calculated with the deduced parameters was in agreement with that calculated with the parameters input for simulation.     

Investigation of nonpolar (1 1 2¯ 0) a-plane ZnO films grown under various Zn/O ratios by plasma-assisted molecular beam epitaxy

Structural and optical properties of nonpolar a-plane ZnO films grown with different II/VI ratios on r-plane sapphire substrates by plasma-assisted molecular beam epitaxy were investigated. Even by increasing the II/VI ratio across the stoichiometric flux condition a consistent surface morphology of striated stripes along the ZnO 〈0 0 0 1〉 direction without any pit formation was observed, which is contrary to polar c-plane ZnO films. Root mean square surface roughness, full width at half maximum values of X-ray rocking curves, defect densities, and photoluminescence were changed with the II/VI ratio. The sample grown with stoichiometric flux condition showed the lowest value of rms roughness, the smallest threading dislocation and stacking fault densities of ∼4.7×10⁸ cm⁻² and ∼9.5×10⁴ cm⁻¹, respectively, and the highest intensity of D^oX peak. These results imply that the stoichiometric flux growth condition is suitable to obtain superior structural and optical properties compared to other flux conditions.     

Epitaxial growth of tin oxide film on TiO2(1 1 0) using molecular beam epitaxy

Growth of tin oxide thin films using molecular beam epitaxy in a pyrolyzed nitrogen dioxide atmosphere on a titanium dioxide (1 1 0) substrate was investigated using X-ray photoelectron spectroscopy (XPS), electron diffraction, and atomic force microscopy (AFM). Properties of deposited films were studied for their dependence on substrate temperature and oxidation gas pressure. Analyses using XPS data revealed that tin atoms were fully oxidized to Sn⁴⁺ and SnO₂ films were grown epitaxially in deposition conditions of substrate temperatures of 627 K or higher and NO₂ pressure greater than 3×10⁻³ Pa. At a substrate temperature of 773 K, a smooth surface with atomic steps was visible in the SnO₂ films, but above or below this temperature, fine grains with crystal facets or porous structures appeared. At pressures of 8×10⁻⁴ to 3×10⁻⁴ Pa, the randomly oriented SnO phase was dominantly grown. Further decreasing the pressure, the Sn metal phase, which was epitaxially crystallized at less than 500 K, was also grown.     

Czochralski-growth of germanium crystals containing high concentrations of oxygen impurities

Oxygen-containing germanium (Ge) single crystals with low density of grown-in dislocations were grown by the Czochralski (CZ) technique from a Ge melt, both with and without a covering by boron oxide (B₂O₃) liquid. Interstitially dissolved oxygen concentrations in the crystals were determined by the absorption peak at 855 cm⁻¹ in the infrared absorption spectra at room temperature. It was found that oxygen concentration in a Ge crystal grown from melt partially or fully covered with B₂O₃ liquid was about 10¹⁶ cm⁻³ and was almost the same as that in a Ge crystal grown without B₂O₃. Oxygen concentration in a Ge crystal was enhanced to be greater than 10¹⁷ cm⁻³ by growing a crystal from a melt fully covered with B₂O₃; with the addition of germanium oxide powder, the maximum oxygen concentration achieved was 5.5×10¹⁷ cm⁻³. The effective segregation coefficients of oxygen in the present Ge crystal growth were roughly estimated to be between 1.0 and 1.4.     

SIMS and Raman characterizations of ZnO:N thin films grown by MOCVD

Nitrogen was incorporated into ZnO films grown by metalorganic chemical vapour deposition (MOCVD) on ZnO substrates using DMZn-TEN, tert-butanol and diallylamine, respectively, as zinc, oxygen and doping sources. The carrier gas was either hydrogen or nitrogen and the partial pressure ratio (R_VI/II) was varied in order to favor the nitrogen incorporation and/or reduce carbon related defects. The ZnO films have been characterized by Micro-Raman scattering and SIMS measurements. SIMS measurements confirm the nitrogen incorporation with concentrations extending from ∼10¹⁹ cm⁻³ to ∼4×10²⁰ cm⁻³. Raman spectra show nitrogen local vibration modes in films grown at low R_VI/II ratio and using H₂ as carrier gas. However, a vibration band attributed to carbon clusters dominates the Raman spectra for films grown with N₂ carrier. The contribution of N complexes was discussed. The strain was calculated for the as-grown and annealed films and it changes from tensile to compressive after annealing.     

Nucleation kinetics of paracetamol–ethanol solutions from metastable zone widths

A study of the nucleation kinetics for a cooling crystallisation of paracetamol–ethanol solutions in a batch reactor is described in this paper. Metastable zone width (MSZW) experiments were conducted in order to estimate the nucleation kinetics of the system. Measured MSZWs can be affected by numerous process parameters, such as cooling rate, concentration, agitation rate, and working volume. Two theoretical approaches were employed to estimate the nucleation kinetics, the classical mass based approach of Nývlt, and a more recent approach by Kubota, which also considers number density. Both approaches were found to produce similar estimates for the nucleation rates of the paracetamol–ethanol solutions as a function of supersaturation for an assumed nucleus size of 10 μm. The theory of Kubota was found to predict satisfactory estimates for the induction time of the nucleation process from MSZW data. The induction time was observed to be independent of the solution temperature as suggested by Kubota’s theory. This is a novel finding and serves to validate the induction time theory of Kubota. In this investigation, MSZWs were observed to decrease with increased levels of agitation and found to be independent of working volume.     

Chemically assisted vapour transport for bulk ZnO crystal growth

A chemically assisted vapour phase transport (CVT) method is proposed for the growth of bulk ZnO crystals. Thermodynamic computations have confirmed the possibility of using CO as a sublimation activator for enhancing the sublimation rate of the feed material in a large range of pressures (10⁻³ to 1 atm) and temperatures (800–1200 °C). Growth runs in a specific and patented design yielded single ZnO crystals up to 46 mm in diameter and 8 mm in thickness, with growth rates up to 400 μm/h. These values are compatible with an industrial production rate. N type ZnO crystals (μ=182 cm²/(V s) and n=7 10¹⁵ cm⁻³) obtained by this CVT method (Chemical Vapour Transport) present a high level of purity (10–30 times better than hydrothermal ZnO crystals), which may be an advantage for obtaining p-type doped layers ([Li] and [Al] <10⁺¹⁵ cm⁻³). Structural (HR-XRD), defect density (EPD), electrical (Hall measurements) and optical (photoluminescence) properties are presented.     

Growth of AlN single crystalline boules

We have obtained high-quality, crack-free AlN wafers using a convex thermal field inside the growth chamber. Free-standing AlN boules of 15 mm in height and 15 mm in diameter were grown. The carbon concentration was found to be similar in all parts of the boule (∼8×10¹⁸ cm⁻³) while the initial O concentration was higher (∼1×10¹⁹ cm⁻³) and slightly decreased during growth. It was found that O incorporated differently on different crystallographic faces. High resolution XRD showed a continuous improvement in crystal quality as a function of boule length. The full width at half maximum (FWHM) of the double crystal rocking curves decreased from 78 in at the beginning of growth to 13 in at the growth end. To the best of our knowledge, this is the first report on impurity incorporation on different crystallographic facets obtained from the same boule.     

Assessment of defect reduction methods for nonpolar a-plane GaN grown on r-plane sapphire

This work assesses the relative effectiveness of four techniques to reduce the defect density in heteroepitaxial nonpolar a-plane GaN films grown on r-plane sapphire by metalorganic vapour phase epitaxy (MOVPE). The defect reduction techniques studied were: 3D–2D growth, SiN_x interlayers, ScN interlayers and epitaxial lateral overgrowth (ELOG). Plan-view transmission electron microscopy (TEM) showed that the GaN layer grown in a 2D fashion had a dislocation and basal-plane stacking fault (BSF) density of (1.9±0.2)×10¹¹ cm⁻² and (1.1±0.9)×10⁶ cm⁻¹, respectively. The dislocation and BSF densities were reduced by all methods compared to this 2D-grown layer (used as a seed layer for the interlayer and ELOG methods). The greatest reduction was achieved in the (0 0 0 1) wing of the ELOG sample, where the dislocation density was <1×10⁶ cm⁻² and BSF density was (2.0±0.7)×10⁴ cm⁻¹. Of the in-situ techniques, SiN_x interlayers were most effective: the interlayer with the highest surface coverage that was studied reduced the BSF density to (4.0±0.2)×10⁵ cm⁻¹ and the dislocation density was lowered by over two orders of magnitude to (3.5±0.2)×10⁸ cm⁻².     

Reduction of the dislocation density in molecular beam epitaxial CdTe(2 1 1)B on Ge(2 1 1)

The high dislocation density (2×10⁷/cm² for a thickness of 7 μm) in CdTe(2 1 1)B on Ge(2 1 1) has become a roadblock for the technological exploitation of this material. We present a systematic study of in situ and post-growth annealing cycles aimed at reducing it. An etch pit density of 2×10⁶/cm² was achieved by optimizing the growth conditions and annealing the samples in situ. This finding was corroborated by high-resolution X-ray diffraction, atomic force microscopy, photoluminescence and ellipsometry measurements.     

A low silica, barium borate glass-ceramic for use as seals in planar SOFCs

A low silica, barium borate glass-ceramic for use as seals in planar SOFCs containing 64 mol%BaO, 3 mol%Al₂O₃ and 3 mol%SiO₂ was studied. Coefficient of thermal expansion (CTE) between 275-550 °C, glass transition temperature (T_g), and dilatometric softening point (T_s) of the parent glass were 11.9 × 10⁻⁶ °C⁻¹, 552 °C, and 558 °C, respectively. Glass-ceramic was produced by devitrification heat treatment at 800 °C for 100 h. It was found that nucleation heat treatment, seeding by 3 wt%ZrO₂ as glass-composite and pulverization affected the amount, size and distribution of crystalline phases. SEM-EDS and XRD results revealed that crystalline phases presented in the devitrified glass-ceramic were barium aluminate (BaAl₂O₄), barium aluminosilicate (BaAl₂Si₂O₈) possibly with boron associated in its crystal structure, and barium zirconate (BaZrO₃). CTE of the devitrified glass-ceramic was in the range of (10.1-13.0) × 10⁻⁶ °C⁻¹. Good adhesion was obtained both in the cases of glass and devitrified glass-ceramic with YSZ and AISI430 stainless steel. Interfacial phenomena between these components were discussed.     

Crystal growth and luminescent properties of Pr-doped K(Y,Lu)3F10 single crystal for scintillator application

Pr1%:K(Y_1−xLu_x)₃F₁₀ (x=0, 0.2, 0.4) single crystals were grown by the μ-PD method. All the grown crystals were greenish and perfectly transparent without any inclusions or cracks. Radioluminescence spectra and decay kinetics of the Pr1%:K(Y,Lu)₃F₁₀ crystals were measured. Emission from the Pr³⁺ 5d–4f transition, peaking around 260 nm and of the decay time of around 22 ns were observed. The 5d–4f emission intensities of the Pr1%:K(Y,Lu)₃F₁₀ crystals were higher than that of the standard BGO scintillator.     

Size-dependent nucleation and growth kinetics model for potassium chloride—Application in Qarhan salt lake

The nucleation process and crystallization kinetics of KCl were studied in order to investigate the problems in KCl production in Qarhan salt lake. The correlation between particle size and KCl crystal growth rate was studied in a continuous mixed-suspension mixed-product removal (MSMPR) crystallizer. Classical theory of primary nucleation was used to study the homogeneous and heterogeneous nucleation mechanism of KCl crystallization. Several size-independent growth models and size-dependent growth models, such as Bransom, C-R, MJ2, ASL, and MJ3, were examined by the population balance theory. Results showed that MJ3 model closely fitted the experimental data, the mean relative deviation was 0.94%, the crystal growth rate G=2068{1−exp[−1.081×10−5(L+961.882)]}.