The effect of oxygen pressure on the microstructures of Co-doped rutile TiO2 thin films grown by pulsed laser deposition

Comprehensive microstructures of 7% cobalt-doped rutile TiO₂ thin films grown on c-plane sapphire by pulsed laser deposition were characterized using transmission electron microscopy (TEM). The effects of oxygen pressure during growth on the Co distribution inside the films were investigated, and the detailed growth mechanism of both TiO₂ and TiO₂+Co was discussed. The similar oxygen sublattices and low mismatch between (1 0 0) rutile and c-plane sapphire favors the rutile phase. However, the three-fold symmetry of the substrate surface resulted in three rutile domain orientation variants, and they grow adjacent to each other. Cobalt was found to precipitate out as nanocrystals inside the TiO₂ matrix as the growth pressure of oxygen was decreased. At 0.05 mTorr oxygen pressure, almost all of the Co segregates into crystallographically aligned nanocrystals with a particle size of 4.4±0.15 nm. All the samples have magnetic coercivity at room temperature. The magnetic moment per Co atom increased with decreased oxygen pressure, suggesting that the Co that replaced the Ti²⁺ in the TiO₂ lattice does not have a large magnetic moment.     

Effect of Mn concentration and growth temperature on nanostructures and magnetic properties of Ge1−xMnx grown on Si

The nanostructures and magnetic properties of Ge_1−xMn_x thin films grown on Si substrates by molecular beam epitaxy, with different nominal Mn concentrations (1−4%) and different growth temperatures, have been systematically investigated by transmission electron microscopy and superconducting quantum interference device. It was discovered that when Ge_1−xMn_x thin films were grown at 70 °C, with increase in Mn concentration, Mn-rich tadpole shaped clusters started to nucleate at 1% Mn and become dominate in the entire film at 4% Mn. While for the thin films grown at 150 °C, tadpoles was firstly seen in the film with 1% Mn and subsequently Mn-rich secondary precipitates became dominant. The magnetic properties show specific features, which are mainly related to the nature and amount of Mn-rich clusters/precipitates within these thin films.     

MOCVD growth of GaN on Si(1 1 1) substrates using an ALD-grown Al2O3 interlayer

GaN thin films have been grown on Si(1 1 1) substrates using an atomic layer deposition (ALD)-grown Al₂O₃ interlayer. This thin Al₂O₃ layer reduces strain in the subsequent GaN layer, leading to lower defect densities and improved material quality compared to GaN thin films grown by the same process on bare Si. XRD ω-scans showed a full width at half maximum (FWHM) of 549 arcsec for GaN grown on bare Si and a FWHM as low as 378 arcsec for GaN grown on Si using the ALD-grown Al₂O₃ interlayer. Raman spectroscopy was used to study the strain in these films in more detail, with the shift of the E₂(high) mode showing a clear dependence of strain on Al₂O₃ interlayer thickness. This dependence of strain on Al₂O₃ thickness was also observed via the redshift of the near bandedge emission in room temperature photoluminescence (RT-PL) spectroscopy. The reduction in strain results in a significant reduction in both crack density and screw dislocation density compared to similar films grown on bare Si. Screw dislocation density of the films grown on Al₂O₃/Si substrates approaches that of typical GaN layers on sapphire. This work shows great promise for the use of oxide interlayers for growth of GaN-based LEDs on Si.     

Electron microscopy studies of epitaxial MgB2 superconducting thin films grown by in situ reactive evaporation

The morphology and chemistry of epitaxial MgB₂ thin films grown using reactive Mg evaporation on different substrates have been characterized by transmission electron microscopy methods. For polycrystalline alumina and sapphire substrates with different surface planes, an MgO transition layer was found at the interface region. No such layer was present for films grown on MgO and 4-H SiC substrates, and none of the MgB₂ films had any detectable oxygen incorporation nor MgO inclusions. High-resolution electron microscopy revealed that the growth orientation of the MgB₂ thin films was closely related to the substrate orientation and the nature of the intermediary layer. Electrical measurements showed that very low resistivities (several μΩ cm at 300 K) and high superconducting transition temperatures (38 to 40 K) could be achieved. The correlation of electrical properties with film microstructure is briefly discussed.     

Growth and structure properties of La1−xSrxMnO3−σ (x=0.2, 0.3, 0.45) thin film grown on SrTiO3 (0 0 1) single-crystal substrate by laser molecular beam epitaxy

La_1−xSr_xMnO_3−σ (LSMO) thin films have been grown on SrTiO₃ (0 0 1) single-crystal substrates using the laser molecular beam epitaxy (MBE) technique. The two-dimensional layer-by-layer growth was in-situ monitored by reflection high-energy electron diffraction (RHEED). Kinetic growth with surface relaxation was also observed, and crystallinity of the thin films was investigated by high-resolution X-ray diffraction. Results of 2θ−ω scans revealed a strong correlation between out-of-plane lattice constant and oxygen content as well as strontium doping concentration. However, further analysis of rocking curve measurements around (0 0 2) plane of thin films grown under different oxygen pressure (P_O2) shown the effects of oxygen content on the crystal structure. An exceptionally low full-width at half-maximum (FWHM) of 0.02° was measured from the sample grown at P_O2 of 5.0 Pa, indicating the almost perfect epitaxial growth of LSMO thin films.     

Epitaxial growth of ZnO thin films on Si substrates by PLD technique

Epitaxial ZnO thin films have been grown on Si(1 1 1) substrates at temperatures between 550 and 700 °C with an oxygen pressure of 60 Pa by pulsed laser deposition (PLD). A ZnO thin film deposited at 500 °C in no-oxygen ambient was used as a buffer layer for the ZnO growth. In situ reflection high-energy electron diffraction (RHEED) observations show that ZnO thin films directly deposited on Si are of a polycrystalline structure, and the crystallinity is deteriorated with an increase of substrate temperature as reflected by the evolution of RHEED patterns from the mixture of spots and rings to single rings. In contrast, the ZnO films grown on a homo-buffer layer exhibit aligned spotty patterns indicating an epitaxial growth. Among the ZnO thin films with a buffer layer, the film grown at 650 °C shows the best structural quality and the strongest ultraviolet (UV) emission with a full-width at half-maximum (FWHM) of 86 meV. It is found that the ZnO film with a buffer layer has better crystallinity than the film without the buffer layer at the same substrate temperature, while the film without the buffer layer shows a more intense UV emission. Possible reasons and preventive methods are suggested to obtain highly optical quality films.     

Growth and optical property characterization of textured barium titanate thin films for photonic applications

We have investigated the growth of barium titanate thin films on bulk crystalline and amorphous substrates utilizing biaxially oriented template layers. Ion beam-assisted deposition was used to grow thin, biaxially textured, magnesium oxide template layers on amorphous and silicon substrates. Growth of highly oriented barium titanate films on these template layers was achieved by molecular beam epitaxy using a layer-by-layer growth process. Barium titanate thin films were grown in molecular oxygen and in the presence of oxygen radicals produced by a 300 W radio frequency plasma. We used X-ray and in situ reflection high-energy electron diffraction (RHEED) to analyze the structural properties and show the predominantly c-oriented grains in the films. Variable angle spectroscopic ellipsometry was used to analyze and compare the optical properties of the thin films grown with and without oxygen plasma. We have shown that optical quality barium titanate thin films, which show bulk crystal-like properties, can be grown on any substrate through the use of biaxially oriented magnesium oxide template layers.     

Growth mechanism of nanorods in REBa2Cu3Oy films (RE: rare-earth element)

Critical current density under magnetic fields has been improved by the introduction of artificial pinning centers. Nanorods in REBa₂Cu₃O_y films are significantly effective as c-axis-correlated pinning centers. However, nanorods sometimes tilt from the c-axis direction of superconducting films. To understand the mechanism of nanorod tilting, ErBa₂Cu₃O_y films containing Ba(Nb_0.5Er_0.5)O₃ (BNO) nanorods were deposited on a SrTiO₃ single crystal with a vicinal surface. Microstructures of the nanorods were examined by transmission electron microscopy (TEM). As a result, it was found that BNO nanorods grew diagonally from steps of the substrate surface in cross-sectional TEM images. The mechanism of the diagonal growth of nanorods can be explained by the segregation coefficient.     

The influences of O/Zn ratio and growth temperature on carbon impurity incorporation in ZnO grown by metal-organic chemical vapor deposition

The strong correlations between the O/Zn ratio and carbon impurity incorporation have been observed on the ZnO films grown using N₂O or O₂ as oxygen source in metal-organic chemical vapor deposition (MOCVD). From in-situ mass spectrometric measurements, the O/Zn ratio in the MOCVD reactor is found to decrease to a minimum value as the growth temperature increased till a critical growth temperature T_c, and then increased above T_c due to different dissociation rates of the oxygen and Zn sources. The strongest D and G modes, which are ascribed to carbon clusters sp² related modes, have been observed in Raman scattering spectroscopy for the ZnO samples grown at T_c, indicating the highest incorporation rate of carbon impurity in the samples grown at T_c. Compared with O₂, N₂O has a low dissociation rate and that leads to a lower value of O/Zn ratio, resulting in much stronger D and G modes and higher incorporation rate of carbon impurities in the samples grown at T_c. It is interesting to note that the lowest specific resistances from Hall effect measurements were also obtained on the samples grown at T_c, indicating possible electrical contributions from the formation of carbon clusters, which should be highly conductive regions in ZnO. Furthermore, ionization or addition of H₂ in the case of N₂O can significantly enhance the dissociation of N₂O, with film quality improved significantly. This study shows that a high O/Zn ratio is critical to suppress carbon impurity incorporation and to grow high quality ZnO by MOCVD, especially at low growth temperature.     

SIMS and Raman characterizations of ZnO:N thin films grown by MOCVD

Nitrogen was incorporated into ZnO films grown by metalorganic chemical vapour deposition (MOCVD) on ZnO substrates using DMZn-TEN, tert-butanol and diallylamine, respectively, as zinc, oxygen and doping sources. The carrier gas was either hydrogen or nitrogen and the partial pressure ratio (R_VI/II) was varied in order to favor the nitrogen incorporation and/or reduce carbon related defects. The ZnO films have been characterized by Micro-Raman scattering and SIMS measurements. SIMS measurements confirm the nitrogen incorporation with concentrations extending from ∼10¹⁹ cm⁻³ to ∼4×10²⁰ cm⁻³. Raman spectra show nitrogen local vibration modes in films grown at low R_VI/II ratio and using H₂ as carrier gas. However, a vibration band attributed to carbon clusters dominates the Raman spectra for films grown with N₂ carrier. The contribution of N complexes was discussed. The strain was calculated for the as-grown and annealed films and it changes from tensile to compressive after annealing.     

Orientation control of LaNiO3 thin films by RF magnetron sputtering with different oxygen partial pressure

Highly (1 1 0)- and (1 0 0)-oriented LaNiO₃ (LNO) thin films were successfully grown on Si (1 0 0) substrate using radio frequency (RF) magnetron sputtering at room temperature (RT). Effects of oxygen partial pressures on the orientation, film composition, surface morphology, and electrical properties of the films were investigated. The nearly complete (1 0 0) orientation was first achieved with oxygen partial pressure beyond 15% in the sputtering gas. The preferred (1 0 0) orientation of growing films is determined by uniform distribution of Ni³⁺ and La/Ni ratio in the films caused by oxygen during sputtering, as well as the lowest surface energy of the films in the crystalline process. LNO films with controlled orientation have low resistivity of 7.0×10⁻⁶ Ω m which is a good basis for integrating ferroelectric capacitors.     

The growth of Pd thin films on a 6H-SiC(0 0 0 1) substrate

Pd thin films, grown on Si-rich 6H-SiC(0 0 0 1) substrates, were studied by atomic force microscopy, electron diffraction and high-resolution transmission electron microscopy. It is concluded that the growth is successful only when all the growth process takes place at room temperature. Under these conditions a very good epitaxial growth of Pd is achieved, despite the large misfit (about 8.6%) between Pd and the substrate and the existence of a semi-amorphous layer between the thin film and the substrate. A large number of twins appear in these films.     

Preparation and the growth mechanism of zinc blende structure tin sulfide films by successive ionic layer adsorption and reaction

Zinc blende structure tin sulfide (SnS) films have been prepared by successive ionic layer adsorption and reaction (SILAR) method. It is found that both the annealing and addition of NH₄Cl or NaCl to cation solution during the SILAR process can promote the crystallization of SnS films. The growth mechanism for this novel structure considered that the initial distribution of cations on the substrate surface during the cation adsorption process is the crucial factor that determines the structure of the final production. Because Cl⁻ anions can complex with Sn²⁺ cations, when the concentration of Cl⁻ in the cation precursor solution increases, more [SnCl]⁺ complex ions are adsorbed on the substrate. These [SnCl]⁺ ions assemble more orderly than Sn²⁺ ions because of the polarity of ions, so crystallized SnS films can be obtained when NH₄Cl or NaCl is added to the cation solution.     

Influence of oxygen/argon ratio on structural,electrical and optical properties of Ag-doped ZnO thin films

Ag-doped ZnO (ZnO:Ag) thin films were deposited on quartz substrates by radio frequency magnetron sputtering technique. The influence of oxygen/argon ratio on structural, electrical and optical properties of ZnO:Ag films has been investigated. ZnO:Ag films gradually transform from n-type into p-type conductivity with increasing oxygen/argon ratio. X-ray photoelectron spectroscopy measurement indicates that Ag substitutes Zn site (Ag_Zn) in the ZnO:Ag films, acting as acceptor, and being responsible for the formation of p-type conductivity. The presence of p-type ZnO:Ag under O-rich condition is attributed to the depression of the donor defects and low formation energy of Ag_Zn acceptor. The I–V curve of the p-ZnO:Ag/n-ZnO homojunction shows a rectification characteristic with a turn-on voltage of ∼7 V.     

Growth of GaN films on PLD-deposited TaC substrates

GaN films were grown by metal organic chemical vapor deposition on TaC substrates that were created by pulsed laser deposition of TaC onto (0 0 0 1) SiC substrates at ∼1000 °C. This was done to determine if good quality TaC films could be grown, and if good quality GaN films could be grown on this closely lattice matched to GaN, conductive material. This was done by depositing the TaC on on-axis and 3° or 8° off-axis (0 0 0 1) SiC at temperatures ranging from 950 to 1200 °C, and examining them using X-ray diffraction, scanning electron microscopy, atomic force microscopy, and transmission electron microscopy. The GaN films were grown on as-deposited TaC films, and films annealed at 1200, 1400, or 1600 °C, and examined using the same techniques. The TaC films were polycrystalline with a slight (1 1 1) texture, and the grains were ∼200 nm in diameter. Films grown on-axis were found to be of higher quality than those grown on off-axis substrates, but the latter could be improved to a comparable quality by annealing them at 1200–1600 °C for 30 min. TaC films deposited at temperatures above 1000 °C were found to react with the SiC. GaN films could be deposited onto the TaC when the surface was nitrided with NH₃ for 3 min at 1100 °C and the low temperature buffer layer was AlN. However, the GaN did not nucleate easily on the TaC film, and the crystallites did not have the desired (0 0 0 1) preferred orientation. They were ∼10 times larger than those typically seen in films grown on SiC or sapphire. Also the etch pit concentration in the GaN films grown on the TaC was more than 2 orders of magnitude less than it was for growth on the SiC.     

Structural,optical and electrical properties of Ga-doped and (Ga,Co)-codoped ZnO films

The Ga-doped and (Ga, Co)-codoped ZnO films were grown on quartz glass substrate by inductively coupled plasma enhanced physical vapor deposition. The effect of Co doping and oxygen pressure on the structural, optical, electrical and magnetic properties of the as-grown films was investigated. The structural characterization revealed that high-quality films were grown with wurtzite structure and c-axis preferred crystalline orientation. The surface morphology was affected by Co doping and oxygen pressure. Room-temperature ferromagnetism was observed in (Ga, Co)-codoped ZnO films. We found that the optical and electrical properties were degraded with Co doping. The Ga-doped ZnO films had an average transmittance of above 88% in the visible wavelength, while (Ga, Co)-codoped ZnO showed a lower average transmittance (∼65%) due to the d-d transitions of Co²⁺. The resistivity and Hall mobility of (Ga, Co)-doped ZnO samples were lower than those of Ga-doped ZnO films when grown at the same oxygen pressure.     

Growth of epitaxial TmFeCuO4 thin films by pulsed laser deposition

Epitaxial thin films of TmFeCuO₄ with a two-dimensional triangular lattice structure were successfully grown on yttria-stabilized-zirconia substrates by pulsed laser deposition and ex situ annealing in air. The films as-deposited below 500 °C showed no TmFeCuO₄ phase and the subsequent annealing resulted in the decomposition of film components. On the other hand, as-grown films deposited at 800 °C showed an amorphous nature. Thermal annealing converted the amorphous films into highly (0 0 1)-oriented epitaxial films. The results of scanning electron microscopic analysis suggest that the crystal growth process during thermal annealing is dominated by the regrowth of non-uniformly shaped islands to the distinct uniform islands of hexagonal base.     

Epitaxial growth of graphitic carbon on C-face SiC and Sapphire by chemical vapor deposition (CVD)

Epitaxial, graphitic carbon thin films were directly grown on C-face/(0 0 0 1¯) SiC and (0 0 0 1) sapphire by chemical vapor deposition (CVD), using propane as a carbon source and without any catalytic metal on the substrate surface. Raman spectroscopy shows the signature of multilayer graphene/graphite growth on both the SiC and sapphire. Raman 2D-peaks have Lorentzian lineshapes with FWHM of ∼60 cm⁻¹ and the ratio of the D-peak to G-peak intensity (I_D/I_G) linearly decreases (down to 0.06) as growth temperature is increased. The epitaxial relationship between film and substrates were determined by X-ray diffraction. On both substrates, graphitic layers are oriented parallel to the substrate, but exhibit significant rotational disorder about the surface normal, and predominantly rhombohedral stacking. Film thicknesses were determined to be a function of growth time, growth temperature, and propane flow rate.     

Properties of Sm‐doped CaNb2O6 thin films deposited by radio‐frequency magnetron sputtering

Sm‐doped CaNb₂O₆ (CaNb₂O₆:Sm) phosphor thin films were prepared by radio‐frequency magnetron sputtering on sapphire substrates. The thin films were grown at several growth temperatures and subsequently annealed at 800 °C in air. The crystallinity, surface morphology, optical transmittance, and photoluminescence of the thin films were investigated by X‐ray diffraction, scanning electron microscopy, ultraviolet‐visible spectrophotometry, and fluorescence spectrophotometry, respectively. All of the thin films showed a main red emission radiated by the transition from the ⁴G_5/2 excited state to the ⁶H_9/2 ground state of the Sm³⁺ ions and several weak bands under ultraviolet excitation with a 279 nm wavelength. The optimum growth temperature for depositing the high‐quality CaNb₂O₆:Sm thin films, which was determined from the luminescence intensity, was found to be 400 °C, where the thin film exhibited an orthorhombic structure with a thickness of 370 nm, an average grain size of 220 nm, a band gap energy of 3.99 eV, and an average optical transmittance of 85.9%. These results indicate that the growth temperature plays an important role in controlling the emission intensity and optical band gap energy of CaNb₂O₆:Sm thin films.     

Microstructural changes in epitaxial YBa2Cu3O7−δ thin films due to creation of O vacancies

Structural and transport properties of YBa₂Cu₃O_7−δ thin films subjected to different heat treatments and, consequently, having different O vacancy contents are investigated. It is observed that lattice parameters of the films follow the trend of the bulk material, indicating that either the additional stresses created in c-axis oriented films by O vacancies are negligibly small or they are relaxed at elevated temperatures. In addition, heat treatment under relatively low O₂ partial pressures, used to create O vacancies, leads to considerable reduction in local variations of lattice spacings in YBa₂Cu₃O_7−δ thin films.