Phase relations around langasite (La3Ga5SiO14) in the system La2O3–Ga2O3–SiO2 in air

Phase relations around langasite (LGS, La₃Ga₅SiO₁₄) were studied on the basis of phase assemblage observed during calcination and crystallization process of samples of various compositions in the ternary system La₂O₃–Ga₂O₃–SiO₂. A ternary compound of apatite structure, La₁₄Ga_xSi_9–xO_39–x/2 was found for the first time. Crystallization of this compound was observed in the cooling process of molten samples of stoichiometric LGS as well as LGS single crystal, demonstrating that LGS is an incongruent-melting compound. A phase diagram was established primarily based on the crystallization sequence in the cooling process.     

Crystal growth, characterization and spectroscopic study of europium-doped NaY(PO3)4

Europium-doped NaY(PO₃)₄ single crystals have been synthesized by the flux method with sizes around 1 mm³. The unit cell parameters at room temperature refined by X-ray powder diffraction are a=7.1510(4) Å; b=13.0070(8) Å; c=9.6973(2) Å; β=90.606(3)°, Z=4 with the space group P2₁/n in monoclinic system. The present single crystals have a needle shape, they are elongated along the a crystallographic direction, and their size is in the 500 μm–1 mm range. The linear thermal expansion tensor parameters were determined, being the maximum value along the b direction, 16.1×10⁻⁶ K⁻¹ and the minimum along the a direction being 11.7×10⁻⁶ K⁻¹. The IR vibration modes attributed to the group P–O are consistent with the crystallographic data concerning the chain aspect of the phosphate anion. This material melts incongruently at 1141 K. Intense visible emissions attributed to Eu^{3+ 5}D₀→⁷F₁, ⁵D₀→⁷F₂ and ⁵D₀→⁷F₄, electronic transitions have been observed after pumping at 355 nm at room temperature.     

Catalytic growth of In2O3 nanobelts by vapor transport

Indium oxide (In₂O₃) nanobelts have been fabricated by thermal evaporation of metallic indium powders with the assistance of Au catalysts. The as-synthesized nanobelts are single-crystalline In₂O₃ with cubic structure, and usually tens of nanometers in thickness, tens to hundreds of nanometers in width, and several hundreds of micrometers in length. The room temperature photoluminescence spectrum of In₂O₃ nanobelts features a broad emission band at 620 nm, which could be attributed to oxygen deficiencies in the as-synthesized belts. The formation of In₂O₃ nanobelts follows a catalyst-assistant vapor—liquid–-solid growth mechanism, which enables the controlled growth of individual belts on predetermined sites.     

Crystal growth of KInO2 from a hydroxide flux

Single crystals of KInO₂ were obtained from a reactive potassium hydroxide flux at 700 °C. KInO₂ crystallizes in the R-3m crystal system with a=3.2998(10) Å, c=18.322(10) Å and V=172.78(12) Å³. The crystal structure is isotypic with that of α-NaFeO₂ and consists of the (1 1 1) layers being occupied alternately by KO₆ and InO₆ octahedra. Three different AInO₂ structure types are discussed.     

Raman scattering study of crystalline and melting states of BaO·2B2O3

Melting and crystallization scenarios of barium tetraborate BaB₄O₇ (BaO·2B₂O₃) are studied in situ by Raman spectroscopy. It is shown that the scenario depends on the temperature–time history of melt. Crystallization conditions of the beta modification of barium tetraborate (β-BaB₄O₇) from a stoichiometric glass structure BaO·2B₂O₃ were investigated.     

Growth and spectral properties of Nd-doped Sr3Y(BO3)3 crystal

A new crystal of Nd³⁺:Sr₃Y(BO₃)₃ with dimension up to 25×35 mm² was grown by Czochralski method. Absorption and emission spectra of Nd³⁺: Sr₃Y(BO₃)₃ were investigated . The absorption band at 807 nm has a FWHM of 18 nm. The absorption and emission cross sections are 2.17×10⁻²⁰ cm² at 807 nm and 1.88×10⁻¹⁹ cm² at 1060 nm, respectively. The luminescence lifetime τ_f is 73 μs at room temperature     

Thermal and laser properties of Yb:YAl3(BO3)4 crystal

Large optical-quality Yb:YAl₃(BO₃)₄(Yb:YAB) crystals have been grown by the flux method. The thermal properties of Yb:YAB crystal were measured for the first time. The thermal properties of Yb:YAB crystal with different Yb³⁺ ion concentrations are also reported. The results show that the ytterbium concentration influences the properties of Yb:YAB crystal. The specific heat decreases with the increase of Yb³⁺ ion concentrations in the experiment range. Apparently, the thermal expansion coefficient increases along the c-direction with the increase of Yb³⁺ ion concentrations, while it changes slightly along the a-direction. The output laser in 1120–1140 nm ranges has been demonstrated pumped by InGaAs laser. The slope efficiency is 3.8%. The self-frequency-doubling output power of 1 mW is achieved.     

Sn3O4 single crystal nanobelts grown by carbothermal reduction process

This article reports on the growth of single crystal Sn₃O₄ nanobelts and SnO by a carbothermal reduction process in two different regions of a furnace tube. Even though intermediate tin oxide compounds (Sn₃O₄) have been observed experimentally, the study of structures based on them is a challenging task. Characterization data allowed us to propose that Sn₃O₄ nanobelts grew by vapor–solid mechanism while SnO grew by self-catalyst vapor–liquid–solid mechanism. Electrical measurements of a single Sn₃O₄ nanobelt were performed at different temperatures, revealing undoped semiconductor characteristics.     

Thermogravimetric analysis and microstructural observations on the formation of GaN from the reaction between Ga2O3 and NH3

Thermogravimetric analysis (TGA) and microstructural observations were carried to investigate the nitridation mechanism of β-Ga₂O₃ powder to GaN under an NH₃/Ar atmosphere. Non-isothermal TGA showed that nitridation of β-Ga₂O₃ starts at ∼650 °C, followed by decomposition of GaN at ∼1100 °C. Isothermal TGA showed that nitridation follows linear kinetics in the temperature range 800–1000 °C. At an early stage of nitridation, small GaN particles (∼5 nm) are deposited on the β-Ga₂O₃ crystal surface and they increase with time. We proposed a mechanism for the nitridation of Ga₂O₃ by NH₃ whereby nitridation of β-Ga₂O₃ proceeds via the intermediate vapor species Ga₂O(g).     

Growth and properties of Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 single crystals directly from melt

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by a modified Bridgman method directly from melt using an allomeric Pb[(Mg_1/3Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal as a seed. X-ray diffraction (XRD) measurement confirmed that the as-grown PZNT91/9 single crystals are of pure perovskite structure. Electrical properties and thermal stabilization of PZNT91/9 crystals grown directly from melt exhibit different characters from those of PZNT91/9 crystals grown from flux, although segregation and the variation of chemical composition are not seriously confirmed by X-ray fluorescence analysis (XPS). The [0 0 1]-oriented PZNT91/9 crystals cut from the middle part of the as-grown crystal boules exhibit broad dielectric-response peaks at around 105 °C, accompanied by apparent frequency dispersion. The values of piezoelectric constant d₃₃, remnant polarization P_r, and induced strain are about 1800–2200 pC/N, 38.8 μC/cm², and 0.3%, respectively, indicating that the quality of PZNT crystals grown directly from melt can be comparable to those of PZNT91/9 single crystals grown from flux. However, further work deserves attention to improve the dielectric properties of PZNT crystals grown directly from melt. Such unusual characterizations of dielectric properties of PZNT crystals grown directly from melt are considered as correlating with defects, microinhomogeneities, and polar regions.     

Solvothermal synthesis of K2V3O8 nanorods

A solvothermal route has been developed to synthesize K₂V₃O₈ nanorods via the reduction of V₂O₅ using ethanol as the reducing agent as well as the solvent at 200°C. X-ray diffraction and selected area electron diffraction analysis revealed that the as-synthesized products are of tetragonal structure K₂V₃O₈. Transmission electron spectroscopy image showed that the obtained K₂V₃O₈ comprises rod-like nanocrystallites. The formation mechanism of K₂V₃O₈ was studied.     

Flux growth of PbMg1/3Ta2/3O3 single crystals

Single crystals of PbMg_1/3Ta_2/3O₃ (PMT) were grown by the flux method. The PbO–Pb₃O₄–B₂O₃ system was used as a solvent. Transparent and light yellow PMT single crystals of rectangular shape and dimensions up to 10×6×4 mm³ were obtained. For the applied growth conditions only, the crystals of the perovskite structure were grown. X-ray diffraction tests showed that at room temperature PMT exhibits cubic symmetry with lattice parameter a=4.042(1) Å. Dielectric studies pointed to relaxor properties of PMT. The characteristic broad and frequency-dependent maximum of dielectric permittivity was observed at 179.7 K (1 kHz).     

Mixed-phase solidification of thin Si films on SiO2

Mixed-phase solidification (MPS) is a new beam-induced solidification method that can produce large-grained and highly (1 0 0)-surface textured polycrystalline Si films on SiO₂. The grains resulting from this mixed-phase solidification (MPS) method, which was conceived based on a well-known phenomenon of coexisting solid–liquid regions in radiatively melted Si films, are found to be essentially devoid of various intragrain defects that always plague, and subsequently degrade the utility of large-grained Si films previously obtained using other crystallization techniques. It is experimentally shown that multiple exposures are required in order to generate such a polycrystalline microstructure from an initial amorphous precursor. The observed trends are conceptually explained in terms of the melt being initiated primarily at grain boundaries in polycrystalline films, and melting and solidification subsequently proceeding laterally at interface-location specific rates as determined by the local thermodynamic factors, which include the anisotropic surface and interfacial energies of the grains, and the unusual local thermal profile—all transpiring within a near-equilibrium but nonisothermal and dynamic environment that needs to address the thermal and stability requirements associated with the coexisting solid–liquid regions.     

Growth and optical properties of self-frequency-doubling laser crystal Yb:LuAl3(BO3)4

Single crystal of Yb:LuAl₃(BO₃)₄(Yb:LuAB) was grown by the flux method for the first time. The cell parameters of the grown crystal were estimated by X-ray diffraction analysis. The result indicates the symmetry of trigonal space group R32, with lattice parameters a=b=9.26372 Å, c=7.21405 Å, V=536.14 Å³, and Z=4. The absorption and emission spectra of Yb:LuAB crystal at room temperature has also been studied. The fluorescence lifetime for Yb:LuAB crystal is about 1.48 ms. The heat capacity was measured from 25 to 500 °C. Its second harmonic generation efficiency in LuAl₃(BO₃)₄ crystal is 3–4 times that of KDP crystal. These results show that Yb:LuAB crystal would be a potential self-frequency-doubling laser crystal.     

Thermal-induced phase transition and assembly of hexagonal metastable In2O3 nanocrystals: A new approach to In2O3 functional materials

This paper reports on the thermal-induced performance of hexagonal metastable In₂O₃ nanocrystals involving in phase transition and assembly, with particular emphasis on the assembly for the preparation of functional materials. For In₂O₃ nanocrystals, the metastable phase was found to be thermally unstable and transform to cubic phase when temperature was higher than 600 °C, accompanied by assembly as well as evolution of optical properties, but the two polymorphs coexisted at the temperature ranging from 600 to 900 °C, during which the content of product phase and crystal size gradually increased upon increasing temperature. The assembly of In₂O₃ nanocrystals can be developed to fabricate In₂O₃ functional materials, such as various ceramic materials, or even desired nano- or micro-structures, by using metastable In₂O₃ nanocrystals as precursors or building blocks. The electrical resistivity of In₂O₃ conductive film fabricated by a hot-pressing route was as low as 3.72×10⁻³ Ω cm, close to that of In₂O₃ single crystal, which is important for In₂O₃ that is always used as conductive materials. The findings should be of importance for both the wide applications of In₂O₃ in optical and electronic devices and theoretical investigations on crystal structures.     

Synthesis of Y2O3:Eu phosphors by bicontinuous cubic phase process

A novel approach for preparation of red-emitting europium-doped yttrium oxide phosphor (Y₂O₃:Eu) by using the bicontinuous cubic phase (BCP) process was reported in this paper. The BCP system was composed of anionic surfactant sodium bis(2-ethylhexyl)sulfosuccinate (AOT) and aqueous yttrium nitrate/europium nitrate solution. Energy dispersive spectrometer analysis revealed the homogeneous precipitation occurred in the BCP structure. Thermogravimetric analysis measurements indicated the precursor powder was europium-doped yttrium hydroxide, Y_1−xEu_x(OH)₃. Scanning electron microscopy micrographs showed the precursor powder had a primary size about 30 nm and narrow size distribution. After heat treatment in furnace above 700 °C for 4 h, high crystallinity Y₂O₃:Eu phosphors was obtained. However, the primary size of particles grew to 50–200 nm and the dense agglomerates with a size below 1 μm were formed. X-ray diffraction patterns indicated the crystal structure of precursor powders and Y₂O₃:Eu phosphors were amorphous and body-centered cubic structure, respectively. The photoluminescence analysis showed that the obtained Y₂O₃:Eu phosphor had a strong red emitting at 612 nm and the quenching started at a Eu concentration of 10 mol%. This study indicated that the BCP process could be used to prepare the highly efficient oxide-based phosphors.     

Growth control of stoichiometry in LaMnO3 epitaxial thin films by pulsed laser deposition

We have studied structural, magnetic, and optical transport properties of LaMnO₃ (LMO) thin films grown on SrTiO₃. While the stoichiometric LMO is an insulating antiferromagnet, it tends to be a ferromagnetic insulator when grown as thin films. By exploring the majority of growth parameters, we have found that the bulk-like electronic and magnetic phases can be stabilized by growing thin films under reducing atmospheres and by using more energetic laser processes. These conditions are found to reduce the La deficiency in the film resulting in the greatly improved cation stoichiometry. Since oxides are prone to reduce the oxygen content and to alter the cation ratio under such growth conditions, it suggests that the cation and oxygen stoichiometries in complex oxide thin films can be improved by properly optimizing the growth parameters.     

Study on the properties of CuInSe2 ingots grown from the melt using stoichiometric and non-stoichiometric charges

CuInSe₂ (CIS) ingots have been prepared by direct reaction of stoichiometric and non-stoichiometric proportions of high-purity Cu, In and Se. Two approaches, namely the one-ampoule process (quartz crucible) and two-ampoule process (graphite crucible) were investigated to grow the crystals, using starting charges with excess copper, and (nearly stoichiometric and with excess indium), respectively. The effect of deviation from stoichiometry in the charge on the physical properties of the resulting polycrystals is presented. Compositional analysis of the best part of the ingots with starting metals ratio (Cu/In) greater than or equal to 1 showed that the matrix preserved the original character of the charge and evidenced that the CIS chalcopyrite structure, -CIS, tolerates well a large In excess. In contrast, the composition of the crystal prepared with a 10% Cu excess was nearly-stoichiometric, with chemical images revealing the formation of heterogeneous phases besides -CIS. The inclusions precipitation was found to increase toward the ingot base. Interestingly, powder X-ray diffraction measurements revealed the presence of secondary phases rather in all the samples. The corresponding diffraction peaks were however few and very weak, with intensities of less than 3% the maximum value recorded for the CIS (1 1 2) plane.     

Half opened microtubes of NaYF4:Yb,Er synthesized in reverse microemulsion under solvothermal condition

NaYF₄:Yb,Er micro/nanocrystals with different sizes and morphologies such as nanospheres, short flexural nanorods, and half opened microtubes, were synthesized in reverse microemulsion under solvothermal condition using the quaternary reverse microemulsion system, CTAB/1-butanol/cyclohexane/aqueous solution. The X-ray diffraction analysis confirmed that cubic phase NaYF₄:Yb,Er can completely transform to hexagonal phase with increasing reaction time. The scanning electron microscope and transmission electron microscope images revealed that the morphology of the product can be tailored by varying the reaction time. A possible crystalline growth process of the NaYF₄:Yb,Er micro/nanocrystals was discussed. The obtained half opened microtubes exhibited an intense green upconversion luminescence, which may be attractive in novel optoelectronic devices.     

Growth and properties of Nd:Lu3Ga5O12 laser crystal by floating-zone method

Neodymium (Nd) doped lutetium gallium garnet (Nd:Lu₃Ga₅O₁₂, Nd:LuGG) single crystal was successfully grown by the optical floating-zone method for the first time to our knowledge. Its absorption and luminescence spectra at room temperature were measured. By using the J–O theory, the spectral parameters of Nd:LuGG were calculated, which indicated that Nd:LuGG should possess comparable and even better laser properties than Nd:YAG. The maximum output power of 855 mW at 1062 nm was achieved with slope efficiency of 23.4% under a pump power of 5.2 W, and optical conversion efficiency of 16.4%. All the results show that Nd:LuGG is a potential laser material.