Artificial pinning in thick YBCO films: Pinning potential and c-axis correlation

We have introduced artificial pinning centres in thick (>1 μm) YBCO films grown by Pulsed Laser Deposition using substrate decoration, quasi-multilayers, and target doping approaches. We have found that the frequency dependence of critical current density is consistent with a logarithmic dependence of pinning potential on current density. For most of materials used as nano-dots, artificially-induced pinning centres have a larger potential than natural ones. From angle-dependent in-field transport measurements and from Transmission Electron Microscopy we have found evidence of c-axis correlated pinning centres.     

Critical current densities and vortex dynamics in FeTexSe1−x single crystals

The critical current density and the normalized relaxation rate are reported in FeTe_0.59Se_0.41 single crystal. Critical current density is of order of 10⁵ A/cm², which is comparable to that in Co-doped BaFe₂As₂. In low temperature and low field region, the vortex dynamics of this system is well defined by the collective creep theory, which is quite similar to Co-doped BaFe₂As₂ reported before. We also discuss the origin of the anomaly in the field dependence of the relaxation rate.     

Angular dependence of the critical current density and the temperature scaling of the flux pinning force in YBCO thin film

In this paper, the critical current J_c(Θ) have been investigated as a function of magnetic-field angle Θ. Θ is the angle between the c-axis and the applied magnetic field direction. This investigation concerned three temperature values (60?K, 78?K and 81?K). The normalized pinning force f_p versus the normalized magnetic field h was also studied (f_p?=?F_p / F_pmax and h?=?H / H_max). The F_p expression was determined based on the Kramer model.The studied sample was a single crystal of YBaCuO thin film deposited by the ablation laser method on the surface (100) of a SrTiO₃ substrate.The results of this work show the existence of point core pinning of the normal centers in the low field regime and the occurrence of the flux creep in high field regime.     

Microwave nonlinearity measurements of epitaxial YBa2Cu3O7−x thin film by bridged resonator

A simple bridged resonator method is presented for microwave nonlinearity measurement of epitaxial superconductor thin film. By this method, microwave current is concentrated in local bridged part on the resonator, and local inductive and resistive nonlinearity in this part are measured. At the same time, undesired nonlinearity are eliminated from the tested results by the special current distribution of the resonator, which enhances the accuracy of the measured nonlinearity.     

Influence of oxygen pressure on critical current density and magnetic flux pinning structures in YBa2Cu3O7-x fabricated by chemical solution deposition

This paper studies the effect of oxygen partial pressure on the fabrication of YBa 2 Cu 3 O 7 x films on (00l) LaAlO 3 substrates by metalorganic deposition using trifluoroacetates (TFA-MOD).As the oxygen partial pressure increases to 1500 Pa,a great increase in the superconducting properties is observed at high magnetic fields parallel to the YBCO c axis.The cross-sectional transmission electron microscope images show that a high density of stacking faults in the size range of 10-15 nm may act as flux pinning centres to enhance the critical current density of the YBCO films     

Effects of Pb-ion irradiation on the vortex pinning in melt-textured YBa2Cu3Ox

Melt-textured YBa₂Cu₃O_x quasicrystalline samples were studied for the effects of Pb-ion irradiation on the vortex pinning. The strength of the pinning was monitored by measurements of the saturation remanent magnetization (M_R) as a detailed function of temperature from 4.2 K up to T_c (≈92 K). Our results show that M_R is greatly enhanced by the Pb-ion irradiation at all temperatures below T_c. Specifically, when compared to a similar but nonirradiated sample, the M_R of an optimally irradiated sample is raised by a factor of 3.4 at 4.2 K and, more strikingly, by 12.7 at 77 K. Contrastingly, in an earlier study of a γ-ray irradiated Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O₁₀ sample, the vortex pinning was seen to be enhanced but mainly near 4.2 K, suggesting that the γ-ray irradiation produces highly localized pinning sites. Hence, our present results imply conversely that the Pb-ion irradiation creates extended structural defects that are effective as vortex pinning sites up to relatively high temperatures, including that of liquid nitrogen.     

Surface versus bulk pinning in a HgBa2Ca2Cu3O8+x ceramics

Flux creep measurements on a HgBa₂Ca₂Cu₃O_8+x ceramics are reported. The results of the magnetic relaxation measurements are analyzed both by assuming that the pinning is due to the existence of a surface barrier or exclusively caused by bulk pinning. The action of both the surface and the bulk barriers is evidenced. At 70 K, a very high critical current density of the surface currents is determined, which is higher than the critical current density of the bulk. The field and temperature dependence of the pinning behaviour reflects mainly bulk pinning in 2D. The measurements were repeated after 4 and 12 months to investigate the influence of aging. A destruction of the superconducting properties of the grain boundaries accompanied by a degradation of the surfaces of the grains with time is proved.     

High critical current density YBa2Cu3O7−δ tapes prepared by the surface-oxidation epitaxy method

YBa₂Cu₃O_7−δ (YBCO) films with high critical current density (J_c) were successfully fabricated on nickel tapes buffered with epitaxial NiO. NiO was prepared on the textured nickel tape by the surface-oxidation epitaxy (SOE) method. We have reported so far a critical temperature (T_c) of 87 K and J_c=4–6×10⁴ A/cm² (77 K, 0 T) for the YBCO films on NiO/Ni tapes. To enhance the superconducting properties of the YBCO films on the SOE-grown NiO, depositions of thin oxide cap layers such as YSZ, CeO₂, and MgO on NiO were investigated. These oxide cap layers were epitaxially grown on NiO and provided the template for the epitaxial growth of YBCO films. Substantially improved data of T_c=88 K and J_c=3×10⁵ A/cm² (77 K, 0 T) and 1×10⁴ A/cm² (77 K, Hc, 4 T) were obtained for YBCO film on NiO, by using a MgO cap layer with a thickness of 50 nm. The method described in this paper is a simple way to produce long YBCO tape conductors with high-J_c values.     

Enhancement of the critical current density in YBCO/Ag composites

YBa₂Cu₃O_7 + xAg?(x = 0.0, ?5.0, ?15.0 and 20 wt%) composite samples have been prepared by the solid state reaction method. The changes in structure are confirmed from the X-ray diffraction analysis and SEM measurements. The critical current density is calculated using Bean's formula from the magnetization measurement. We find that the addition of silver in YBCO enhances the critical current density (?J_C) by a factor of nearly six (for 15% Ag) in comparison to pure YBCO. Enhancement of the pinning force (F_P) by a factor of ten is also reported. The enhancement in ?J_C is investigated over a wide range of magnetic fields. These significant changes in ?J_C and F_P are attributed to the presence of Ag particles as efficient artifical pinning centers in YBCO.     

YBa2Cu3O7-δ熔融织构样品的磁响应研究

对YBa₂Cu₃O_7-δ熔融织构样品在不同温度、不同磁场不同外场扫描速率下进行了磁滞回线测量,获得了电流密度J(T,B),lnE-lnJ曲线以及热激活能U₀(T,B)随温度、磁场的变化关系,从而分析了该样品磁响应特性,特别是第二峰(简称峰)受外场扫描速率的影响,探讨了峰形成的真正原因,以及影响峰位置、大小的各种因素 关键词： 磁响应 熔融织构 峰效应 临界电流密度     

Effects of Zn on the grain boundary properties of La2−xSrxCu1−yZnyO4 superconductors

The properties of the grain boundaries (GBs) are of significant importance in high-T_c cuprates. Most large scale applications of cuprate superconductors involve usage of sintered compounds. The critical current density and the ability to trap high magnetic flux inside the sample depend largely on the quality of the GBs. Zn has the ability to pin vortices but it also degrades superconductivity. In this study we have investigated the effect of Zn impurity on the intergrain coupling properties in high-quality La_2−xSr_xCu_1−yZn_yO₄ sintered samples with different hole concentrations, p (≡x), over a wide range of Zn contents (y) using field-dependent AC susceptibility (ACS) measurements. The ACS results enabled us to determine the superconducting transition temperature T_c, and the temperature T_gcp, at which the randomly oriented superconducting grains become coupled as a function of hole and disorder contents. We have analyzed the behavior of the GBs from the systematic evolution of the values of T_gcp(p, y), T_c(p, y), and from the contribution to the field-dependent ACS signal coming from the intergrain shielding current. Zn suppresses both T_c and T_gcp in a similar fashion. The hole content and the carrier localization due to Zn substitution seem to have significant effect on the coupling properties of the GBs. We have discussed the possible implications of these findings in detail in this article.     

Magnetic hysteresis of the magnetoresistance and the critical current density in polycrystalline YBa2Cu3O7−δ–Ag superconductors

A systematic study of the magnetic hysteresis in transport properties of polycrystalline YBa₂Cu₃O_7−δ–Ag compounds has been made based on two kinds of measurements at 77 K and under applied magnetic fields up to 30 mT: critical current density J_c(B_a) and magnetoresistance R(B_a). The R(B_a) curves show a minimum in their decreasing branch occurring at B=B_min which was found to be both the excitation current I_ex and the maximum applied magnetic field B_am dependent. In addition, for a certain value of B_am>5 mT, we have observed that B_min increases with increasing I_ex and reaches a saturation value. The J_c(B_a) curves show a maximum in decreasing applied magnetic fields occurring at B=B_max. We have also found that B_max increases with increasing B_am and reaches a saturation value. The minimum in the R(B_a) and the maximum in J_c(B_a) curves were found to be related to the trapped flux within the grains. All the experimental results are discussed within the context of the flux dynamics and transport mechanisms in these high-T_c materials.     

Crystal orientation dependence of the critical current density in a-axis- and c-axis-oriented MgB2 films

We have investigated the critical current density for MgB₂ films having various crystal orientations prepared by using a hybrid physical-chemical vapor deposition system. An enhancement of the critical current density is clearly presented in MgB₂ films with an a-axis or a b-axis orientation rather than a c-axis orientation. X-ray diffraction patterns reveal a suppression of c-axis orientations while a (100) orientation becomes dominant, and the surface morphology of the a-axis-oriented film shows that the orientation of the c-axis-oriented MgB₂ grains parallel to the plane of the substrate. As the a-axis orientation becomes more dominant in the MgB₂ films, the field performance of the critical current density clearly becomes better. These results suggest that the synthesis of MgB₂ with high ab-plane orientations is one of the keys to enhancing the critical current density in MgB₂.     

In situ grown epitaxial YBa2Cu3O7 − x thin films by pulsed laser deposition under reduced oxygen pressure during cool-down time

We report novel pulsed laser deposition conditions that were used to obtain superconducting epitaxial YBCO thin films, grown in situ using an oxygen pressure lower than the usual one during the cool-down time. We studied the influence of the PLD conditions as substrate temperature, oxygen pressure, laser fluence, and number of laser pulses on the crystallographic and morphological features, and on the superconducting properties of the films. Good superconducting properties were obtained without a high temperature post-deposition annealing process. A maximum critical temperature of 88.6 K was obtained.     

掺杂Y2O3和BaCeO3提高MOD-YBCO超导性能的研究

本文通过在前驱液中添加过量钇盐和铈的有机盐,采用三氟乙酸盐-金属有机沉积法(TFA-MOD) 在铝酸镧单晶基体上制备了含有纳米氧化钇和纳米铈酸钡的YBCO薄膜. 与纯YBCO薄膜相比,掺杂Y₂O₃/BaCeO₃的YBCO膜的临界转变温度几乎保持不变,为91 K左右. 而掺杂Y₂O₃/BaCeO₃的YBCO膜的临界电流密度达到5.0 MA/cm² (77 K, 0T), 是纯YBCO膜临界电流密度的1.5倍.薄膜中的Y₂O₃和BaCeO₃可能在YBCO内部起到了 有效的钉扎磁通作用. 关键词： 钇钡铜氧薄膜 2O₃和纳米BaCeO₃')" href="#">纳米Y₂O₃和纳米BaCeO₃ 磁通钉扎 三氟乙酸盐-金属有机沉积     

Angular dependences of critical current density in YBCO thin films with crossed columnar defects

We investigated the dependences of the critical current density J_c on the magnetic field angle θ in YBa₂Cu₃O_7−δ thin films with the crossed configurations of the columnar defects (CDs). To install the crossed CDs, the films were irradiated using the high energetic Xe ions at two angles relative to the c-axis. The additional peak around the c-axis appears in the J_c(θ) for all irradiated films. In lower magnetic fields, the height of the J_c(θ) peak caused by the crossed CDs with the crossing angles θ_i = ±10° was higher than that for the parallel CDs. It is considered that the correlation of the flux pinning by the crossed CDs along the c-axis occurs even in the case of θ_i = ±25°, which was also suggested by the kink behaviors of the scaling parameters of the current–voltage characteristics near 1/3 of the matching field. In higher magnetic fields, on the other hand, the height and width of the J_c(θ) peak for the crossed CD configurations rapidly reduce with increasing the magnetic field compared to the parallel ones. In the crossed CD configurations, the dispersion in the direction of CDs would prevent the correlation of flux pinning along the c-axis in high magnetic fields, which occurs in the parallel CD configurations due to the collective pinning of flux lines including the interstitial flux lines between the directly pinned flux lines by CDs.     

Vortex pinning in YBa2Cu3O7?x films

Evidence that pinning on linear or planar defects dominates the vortex dynamics in YBa₂Cu₃O_7−x (YBCO) films is provided by complex impedance measurements at temperature 8 K<T<T _c and magnetic field 0<B<6 T. Below the vortex lattice melting transition B_g(T) but above a threshold field B_p≈8(1-T/T _c ) T, the inductance of vortices increases as B², much less rapidly than predicted for collective pinning of vortices by point defects. Above the vortex melting line, critical scaling persists over the region B_g(T<B<B^*(T) where the vortex correlation length ξ exceeds a characteristic length scale ξ^*≡ξ(B=B^*)≈450?. The value of ξ^* is not sensitive to Al-doping in the Cu sites in the lattice and is close to the size of twin domains in the film. The nature of the observed crossovers is discussed in terms of available theoretical models for a glass-liquid transition at B_g.     

Effects of surface damage on critical current density in MgB2 thin films

We investigated the influence of surface damage on the critical current density (J_c) of MgB₂ thin films via 140-keV Co-ion irradiation. The J_c(H) of the surface-damaged MgB₂ films was remarkably improved in comparison with that of pristine films. The strong enhancement of J_c(H) caused by a surface damage in MgB₂ films can be ascribed to additional point defects along with an atomic lattice displacement introduced through low-energy Co-ion irradiation, which is consistent with the change in the pinning mechanism, from weak collective pinning to strong plastic pinning. The irreversible magnetic field (H_irr) at 5 K for surface-damaged MgB₂ films with a thickness of 850 and 1300 nm was increased by a factor of approximately 2 compared with that of a pristine film. These results show that the surface damage produced by low energy ion irradiation can serve as an effective pinning source to improve J_c(H) in a MgB₂ superconductor.     

A new method to preserve the c-axis growth of thick YBa2Cu3O7–δ films grown by pulsed laser deposition

YBa₂Cu₃O_7–δ (YBCO) films were prepared on (1 0 0) MgO substrates by pulsed laser deposition (PLD) method. In order to eliminate the a-axis growth, which is commonly observed in the YBCO film thicker than a critical value, we developed a new PLD target that was sintered at a temperature far below YBCO 123 phase formation. The surface analysis made by AFM technique confirmed that very fine particles of around 20 nm size could be ejected from the new target to the substrate. The fine oxide clusters could be easily moved and incorporated into the YBCO phase thus benefited the c-axis growth even in the thick films. For instance, only the c-axis growth in the new film with a thickness of about 650 nm was larger than a critical thickness of the a-axis growth. However, in the standard film of the same thickness, there is 24.5% of the a-axis growth accompanying the main c-axis growth. Therefore, the c-axis growth could be preserved in the very thick YBCO film by a non-superconducting target.     

Study on reaction mechanism of YBa2Cu3O7-x film by TFA-MOD process

This paper systematically investigates the intermediate phases of YBa2Cu3O7-x (YBCO) film prepared by metalorganic deposition method using trifluoroacetates (TFA-MOD). According to x-ray diffraction and Raman analyses, the precursor film decomposed in a mixture of BaF2, Y2O3 and CuO after the pyrolysis process. Then these intermediate phases converted into tetragonal YBa2Cu3O6.5 at about 725°C. The influence of water vapour pressure on the YBa2Cu3O7-x film growth on LaAlO3 single-crystal substrates was also studied. The films prepared at low water vapour pressures (40-140 hPa) showed poor electrical performance due to the a-axis grain structure and impurity phases. However, the films prepared at 190 hPa exhibited the highest critical temperature of 90 K and the highest Jc of 3.8 MA/cm2, which was attributed to the formation of a purer YBCO phase and stronger biaxial texture.