Luminescence investigation of red phosphors Ca0.54Sr0.34−1.5xEu0.08Smx(MoO4)y (WO4)1−y for UV-white LED device

Ca_0.54Sr_0.34−1.5xEu_0.08Sm_x(MoO₄)_y (WO₄)_1−y red phosphors were prepared by solid-state reaction using Na⁺ as a charge compensator for light-emitting diodes (LED). The effects of Na⁺ concentration, synthesis temperature, reaction time and Eu³⁺ concentration were studied for the properties of luminescence and crystal structure of red phosphors. The results show that the optimum reaction condition is 6%, 900 °C, 2 h and 8%. The photoluminescence spectra show that red phosphors are effectively excited at 616 nm by 292, 395 and 465 nm. The wavelengths of 465 nm nicely match the widely applied emission wavelengths of blue LED chips.     

Double metal-insulator peaks and effect of Sm substitution on magnetic and transport properties of hole-doped La0.85Ag0.15MnO3

La_0.85−xSm_xAg_0.15MnO₃ (x=0−0.2) ceramics were prepared using the conventional solid-state synthesis method to investigate the effect of Sm³⁺ substitution on magnetic and electrical transport properties. Magnetic susceptibility versus temperature measurements showed all samples exhibit ferromagnetic to paramagnetic transition with Curie temperature, T_c decreasing from 283 K (x=0) to 164 K (x=0.2) with increasing Sm³⁺. The observed slope in susceptibility, χ′ versus temperature curves below T_c indicates the possible presence of FM and AFM phases in the metallic region. In addition, a deviation from the Curie-Weiss law above T_c in 1/χ′ versus T curves indicates the existence of a Griffith's phase in the x=0.05−0.2 samples due to the Sm³⁺ ion substitution. The Griffith temperature, T_G was found to decrease from 295 K (x=0.05) to 229 K (x=0.2). Electrical resistivity measurements of the samples in zero field showed transition from metallic behavior to insulating behavior as the temperature was increased. For x=0, two metal-insulator, MI transition peaks were observed at T_p1=282 K and at T_p2=250 K. Both peaks shifted to lower temperatures with the increase in Sm³⁺. The relative resistivity of the first peak to the second peak decreases with increasing Sm³⁺ for x>0.05 while at x=0.2 the T_p1 peak was strongly suppressed. Magnetoresistance, MR was observed to weaken with Sm³⁺ substitution. The metallic region of the ρ(T) curve of the x=0−0.15 samples was fitted to the model of electron-electron and electron-magnon scattering while the insulating region was fitted to the variable range hopping, VRH model. The resistivity behavior indicated that the substitution of Sm³⁺ weakened the double exchange process and enhanced the Jahn-Teller effect. Our results indicated that the T_p1 peak is strongly related to the double-exchange mechanism while the T_p2 peak is suggested to originate from magnetic inhomogeneity.     

Room-temperature ferromagnetism in Sn1−xMnxO2 nanocrystalline thin films prepared by ultrasonic spray pyrolysis

Sn_1−xMn_xO₂ (x=0.01-0.05) thin films were synthesized on quartz substrate using an inexpensive ultrasonic spray pyrolysis technique. The influence of doping concentration and substrate temperature on structural and magnetic properties of Sn_1−xMn_xO₂ thin films was systematically investigated. X-ray diffraction (XRD) studies of these films reflect that the Mn³⁺ ions have substituted Sn⁴⁺ ions without changing the tetragonal rutile structure of pure SnO₂. A linear increase in c-axis lattice constant has been observed with corresponding increase in Mn concentration. No impurity phase was detected in XRD patterns even after doping 5 at% of Mn. A systematic change in magnetic behavior from ferromagnetic to paramagnetic was observed with increase in substrate temperature from 500 to 700 °C for Sn_1−xMn_xO₂ (x=0.01) films. Magnetic studies reveal room-temperature ferromagnetism (RTFM) with 3.61×10⁻⁴ emu saturation magnetization and 92 Oe coercivity in case of Sn_1−xMn_xO₂ (x=0.01) films deposited at 500 °C. However, paramagnetic behavior was observed for the films deposited at a higher substrate temperature of 700 °C. The presence of room-temperature ferromagnetism in these films was observed to have an intrinsic origin and could be obtained by controlling the substrate temperature and Mn doping concentration.     

Electromagnetic and microwave absorbing properties of Co2Z-type hexaferrites doped with La

Z-type ferrites doped with La³⁺, Ba_3−xLa_xCo₂Fe₂₄O₄₁ (x=0.00-0.30), were prepared by sol-gel method. The effect of the substitution La³⁺ rare-earth ions for Ba²⁺ ions on the microstructure, complex permeability, permittivity and microwave absorption of the samples was investigated. The results show that the major phase of the ferrites changed to Z-phase when sintering temperature was 1250 °C for 5 h. With the increase of the substitution ratio of La³⁺ ions from 0.0 to 0.3, the lattice parameters a and c increased gradually, which resulted in the change of the particle shape and size. The data of magnetism showed that the addition of La³⁺ ions make the ferrite a better soft magnetic material due to increase of magnetization (σ_s) and decrease of coercivity (H_c). The La³⁺ ions doped in the ferrite not only improved complex permeability and complex permittivity, but also microwave absorbency.     

Combustion synthesis and luminescence properties of NaY1−xEux(WO4)2 phosphors

The red phosphors NaY_1−xEu_x(WO₄)₂ with different concentrations of Eu³⁺ were synthesized via the combustion synthesis method. As a comparison, NaEu(WO₄)₂ was prepared by the solid-state reaction method. The phase composition and optical properties of as-synthesized samples were studied by X-ray powder diffraction and photoluminescence spectra. The results show that the red light emission intensity of the combustion synthesized samples under 394 nm excitation increases with increase in Eu³⁺ concentrations and calcination temperatures. Without Y ions doping, the emission spectra intensity of the NaEu(WO₄)₂ phosphor prepared by the combustion method fired at 900 °C is higher than that prepared by the solid-state reaction at 1100 °C. NaEu(WO₄)₂ phosphor synthesized by the combustion method at 1100 °C exhibits the strongest red emission under 394 nm excitation and appropriate CIE chromaticity coordinates (x=0.64, y=0.33) close to the NTSC standard value. Thus, its excellent luminescence properties make it a promising phosphor for near UV InGaN chip-based red-emitting LED application.     

Luminescent properties of HTP AgGd1−xW2O8:Eux and AgGd1−x(W1−yMoy)2O8:Eux phosphor for white LED

Intense red phosphors, AgGd_1−xEu_x(W_1−yMo_y)₂O₈ (x=0.0-1.0, y=0.0-1.0), have been synthesized through traditional solid-state reaction and characterized by X-ray diffraction (XRD) and photoluminescence (PL). XRD results reveal that AgGd_1−xEu_xW₂O₈ synthesized at 1000 °C has a tetragonal crystal structure, which is named as high temperature phase (HTP) AgGdW₂O₈. All phosphors compositions with Eu³⁺ show red and green emission on excitation either in the charge-transfer or Eu³⁺ levels. Analysis of the emission spectra with different Eu³⁺ concentrations reveal that the optimum dopant concentration for Eu³⁺ is x=0.6 in the HTP AgGd_1−xEu_xW₂O₈ (x=0.0-1.0). Studies on the AgGd_0.4Eu_0.6(W_1−yMo_y)₂O₈ (y=0.0-1.0) and AgGd_1−xEu_x(W_0.7Mo_0.3)₂O₈ (x=0.0-1.0) show that the emission intensity is maximum for compositions with y=0.3 and x=0.5, respectively, and a decrease in emission intensity is observed for higher y or x values. The Mo⁶⁺ and Eu³⁺ co-doped AgGd(WO₄)₂ phosphors show higher emission intensity in comparison with the singly Eu³⁺-doped AgGd(WO₄)₂ in UV region. The intense emission of the tungstate/molybdate phosphors under 394 and 465 nm excitations, respectively, suggests that these materials are promising candidates as red-emitting phosphors for near-UV/blue GaN-based white LED for white light generation.     

Oxygen deficiency, vacancy clustering and ionic transport in (La,Sr)CoO3 − δ

The equilibrium p(O₂)-T-δ diagrams of perovskite-type La_1 − xSr_xCoO_3 − δ (x = 0.3-0.7), collected at 873-1223 K in the oxygen partial pressure range 10^− 5-1 atm by coulometric titration and thermogravimetric analysis, were analyzed in order to appraise the effects of the point-defect interactions. The nonstoichiometry variations were adequately described combining the rigid-band approach for delocalized holes and the pair-cluster formation reaction involving oxygen vacancies and Co²⁺ cations, whilst coulombic repulsion between the positively charged vacancies can be neglected. The resultant relationships between the oxygen chemical potential and mobile vacancy concentration were used for numerical regression analysis of the steady-state oxygen permeation through dense La_1 − xSr_xCoO_3 − δ membranes, affected by the surface exchange kinetics when Sr²⁺ content is higher than 40-50%. The calculated ionic conductivity is strongly influenced by the defect association processes, and decreases with decreasing concentration of the mobile vacancies as clustering starts to prevail on reduction. The Mössbauer spectroscopy studies of La_1 − xSr_xCoO_3 − δ, doped with 1 mol% ⁵⁷Fe isotope and moderately reduced at p(O₂) ≈ 10⁻⁵ atm, show no long-range vacancy ordering at x ≤ 0.5.     

Low temperature preparation and superconductivity of F-doped SmFeAsO

A low temperature (1100 °C) process of preparing F-doped SmFeAsO samples has been developed using SmF₃ with nanometer scale as the source of fluorine. A series of the SmFeAsO_1−xF_x (x = 0, 0.05, 0.1, 0.15, 0.2, 0.25, 0.3) samples have been prepared using the present method. Compared with previous reports, the present SmF₃ is more effective to introduce F into SmFeAsO system in which a transition temperature of 39 K can be observed when x = 0.05. The superconductivity is definitely enhanced with the increasing F-doping level. All the samples presented to be layered structure and the crystal particle size is about three times larger with sintering time increasing from 36 h to 48 h. Except for the nanometer scale of SmF₃, the flux effect of SmF₃ is recognized to be another reason for the decrease of the sintering temperature. Further more, a relatively large amount of SmF₃ was also employed in the raw materials to introduce excessive F and this has induced higher T_c (55 K) in SmFeAsO_0.8F_0.2+δ system.     

Effects of indium doping on the superconducting properties of YBa2Cu3Oy sintered compounds and thin films

We investigated the effects of indium doping on the superconducting properties of YBCO sintered samples and thin films. In₂O₃-doped YBCO and YBa₂Cu_3−xIn_xO_y sintered samples showed a gradual decrease in the critical temperature (T_c) with increasing indium content; however, a T_c value above 80 K was maintained even up to 30 vol.% addition and x = 0.4, respectively. Ba₃Cu₃In₄O₁₂ was detected by X-ray diffractometry and energy-dispersive X-ray spectroscopy as a reaction product for both sintered samples. The normalized J_c under a magnetic field of 0.1 T showed a maximum at x = 0.3. Indium-doped YBCO films prepared by pulsed laser deposition showed a similar dependence of T_c on indium content as the sintered samples.     

High-temperature oxidation resistance and magnetic properties of Si-doped Sm2Co17-type magnets at 500 °C

The high-temperature oxidation resistance and magnetic properties of Si-doped Sm₂Co₁₇-type magnets at 500 °C were systematically investigated. The Sm(Co_0.76, Fe_0.1, Cu_0.1, Zr_0.04)₇Si_x (x=0–0.6) magnets were prepared by the conventional powder metallurgical technique. It is found that the addition of silicon in the Sm₂Co₁₇-type magnet can remarkably improve its oxidation resistance. Moreover, a small amount of silicon addition can also increase its high-temperature intrinsic coercivity. A maximum intrinsic coercivity of 6.7 kOe at 500 °C was obtained for the Sm₂Co₁₇-type magnet with Si content x=0.4, whose high-temperature maximum energy product loss was about 2.5 times smaller than pure Sm₂Co₁₇-type magnet after oxidation at 500 °C for 100 h, indicating the enhanced oxidation resistance. Its corresponding Curie temperature and saturation magnetization are about 723.9 °C and 7.4 kG, respectively.     

Effect of Ag substitution on the electromagnetic property and microwave absorption of LaMnO3

La_1−xAg_xMnO₃ perovskites with different doping Ag-content were prepared by the sol–gel method. The electromagnetic characteristics and microwave loss behavior of these ion-doped rare-earth manganites were studied in the 2–18 GHz frequency range. The microstructure and morphology of the samples were characterized by X-ray diffraction (XRD), and scanning electron microscopy (SEM) techniques. The complex permittivity spectra, the complex permeability spectra and microwave reflection loss were measured by a microwave vector network analyzer system. The XRD patterns show that the crystalline perovskite main phase ABO₃ is formed and impurity phases disappear when calcined at 1100 °C, and Ag metal as an impurity phase appears when excessive Ag⁺ is doped. The SEM image indicates that many of the La_0.85Ag_0.15MnO₃ particles are fiber-like or ellipsoidal. Magnetic loss and dielectric loss coexist and cooperate in microwave attenuation by moderate substitution of Ag⁺ for La³⁺. The microwave absorption property of the La_0.85Ag_0.15MnO₃ sample is enhanced with the bandwidth below −10 dB at about 6 GHz and the peak value of reflection loss is near −25.0 dB at the layer thickness of 2 mm.     

Crystal structure and photoluminescence of (Y1−xCex)2Si3O3N4

Oxonitridosilicate phosphors with compositions of (Y_1−xCe_x)₂Si₃O₃N₄ (x=0−0.2) have been synthesized by solid state reaction method. The structures and photoluminescence properties have been investigated. Ce³⁺ ions have substituted for Y³⁺ ions in the lattice. The emission and excitation spectra of these phosphors show the characteristic photoluminescence spectra of Ce³⁺ ions. Based on the analyses of the diffuse reflection spectra and the PL spectra, a systematic energy diagram of Ce³⁺ ion in the forbidden band of sample with x=0.02 is given. The best doping Ce content in these phosphors is ∼2 mol%. The quenching temperature is ∼405 K for the 2 mol% Ce content sample. The luminescence decay properties were investigated. The primary studies indicate that these phosphors are potential candidates for application in three-phosphor-converted white LEDs.     

Luminescent properties of KGd1−x(WO4)2:Eux and KGd1−x(WO4)2−y(MoO4)y:Eux phosphors in UV-VUV regions

KGd_1−x(WO₄)_2−y(MoO₄)_y:Eu³⁺_x(0.1?x?0.75, y=0 and 0.2) phosphors are synthesized through traditional solid-state reaction and their luminescent properties in ultraviolet (UV) and vacuum ultraviolet (VUV) regions are investigated. Under 147 nm excitation, these phosphors show characteristic red emission with good color purity. In order to improve their emission intensity, the MoO₄²⁻ (20 wt%) is introduced into the anion of KGd_1−x(WO₄):Eu³⁺_x. The Mo⁶⁺ and Eu³⁺ co-doped KGd(WO₄)₂ phosphors show higher emission intensity in comparison with the singly Eu³⁺-doped KGd(WO₄)₂ in VUV region. The chromaticity coordination of KGd_0.45(WO₄):Eu³⁺_0.55 is (x=0.669, y=0.331), while that of KGd_0.45(WO₄)_1.8(MoO₄)_0.2:Eu³⁺_0.55 is (x=0.666, y=0.334) in VUV region.     

Synthesis and magnetic properties of La-substituted M-type Sr hexaferrites

Single-phase M-type hexagonal ferrites Sr_1−xLa_xFe₁₂O₁₉ (0≤x≤1) were prepared by a ceramic route. The stability limits of the ferrite phases were determined with a combination of various microscopy techniques, electron-probe micro-analysis, powder X-ray diffraction and thermal analysis. SrFe₁₂O₁₉ (x=0) is stable up to 1420 °C, whereas LaFe₁₂O₁₉ (x=1) exists between 1360 and 1400 °C only. The lattice parameters of Sr_1−xLa_xFe₁₂O₁₉ exhibit a linear variation with x, i.e. a₀ slightly increases and c₀ decreases with x, leading to a decrease of the unit cell volume with x. The saturation magnetization at T=5 K decreases with increasing La concentration. Room temperature Mössbauer analysis shows that the Fe³⁺/Fe²⁺ valence change occurs in the 2a sites for the whole composition range.     

Structural, magnetic and magnetotransport behavior of La0.7SrxCa0.3−xMnO3 compounds

A systematic investigation of the structural, magnetic and electrical properties of a series of nanocrystalline La_0.7Sr_xCa_0.3−xMnO₃ materials, prepared by high energy ball milling method and then annealed at 900 °C has been undertaken. The analysis of the XRD data using the Win-metric software shows an increase in the unit cell volume with increasing Sr ion concentration. The La_0.7Sr_xCa_0.3−xMnO₃ compounds undergo a structural orthorhombic-to-monoclinic transition at x=0.15. Electric and magnetic measurements show that both the Curie temperature and the insulator-to-metal transition temperature increase from 259 K and 253 K correspondingly for La_0.7Ca_0.3MnO₃ (x=0) to 353 K and 282 K, respectively, for La_0.7Sr_0.3MnO₃ (x=0.3). It is argued that the larger radius of Sr²⁺ ion than that of Ca²⁺ is the reason to strengthen the double-exchange interaction and to give rise to the observed increase of transition temperatures. Using the phenomenological equation for conductivity under a percolation approach, which depends on the phase segregation of ferromagnetic metallic clusters and paramagnetic insulating regions, we fitted the resistivity versus temperature data measured in the range of 50-320 K and found that the activation barrier decreased with the raising Sr²⁺ ion concentration.     

Luminescence enhancement in bromine and samarium co-doped TiO2 semiconductor nanocrystalline powders

In this paper, TiO₂:Sm³⁺ (0.75 mol%) nanoparticles doped with different amounts of Br⁻ were prepared by an improved sol-gel method and were characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), VG ESCALAB MKIIX-ray photoelectron spectrometer (XPS) and ultraviolet-visible diffuse reflectance spectroscopy (UV-vis DRS). Their photoluminescence (PL) properties were investigated at room temperature. The emissions of ⁴G_5/2-⁶H_J (J=5/2, 7/2, 9/2) transitions of Sm³⁺ ions were observed under the excitation wavelength at 350 nm and the emission intensity depended strongly on the doping amount of Br⁻. TiO₂:Sm³⁺ (0.75 mol%) nanoparticles doped with 1 mol% of Br⁻ calcined at 700 °C exhibit highest intensity of luminescence, which is nearly three times than the undoped one. The mechanism of photoluminescence in the co-doped system was discussed.     

Highly cation-deficient manganese perovskite, La1−xMn1−yO3 with x=y

Oxidative (δ>0) nonstoichiometry in the perovskite ‘LaMnO_3+δ’ has been known to be manifested not with O interstitials but rather with cation vacancies of equal amounts at the two cation sites, La and Mn, i.e. La_1−xMn_1−yO₃ with x=y. Here, we report the fabrication of samples with record-high cation-vacancy concentrations (x>0.12 or δ>0.4) by means of a variety of high-pressure oxygenation techniques. Linear (negative) dependence of the cell volume on x was observed within the whole x range investigated, down to 56.9 Å³ (per formula unit) for a sample oxygenated at 5 GPa and 1100 °C using Ag₂O₂ as an excess oxygen source. With increasing degree of cation deficiency in La_1−xMn_1−xO₃, the ferromagnetic transition temperature was found to follow a bell shape with respect to x exhibiting a maximum of ∼250 K about x≈0.1. For moderately oxygenated samples large magnetoresistance effect was evidenced.     

Low-voltage cathodoluminescence property of Li-doped Gd2−xYxO3:Eu

Cathodoluminescent (CL) spectra of Li-doped Gd_2−xY_xO₃:Eu³⁺ solid-solution (0.0?x?0.8) were investigated at low voltages (300 V-1 kV). The CL intensity is maximum for the composition of x=0.2 and gradually reduces with increasing the amount of substituted Y content. In particular, small (∼100 nm) particles of Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ are obtained by firing the citrate precursors at only 650°C for 18 h. Relative red-emission intensity at 300 V of this phosphor is close to 180% in comparison with that of commercial red phosphor Y₂O₃:Eu³⁺. An increase of firing temperature to 900°C results in 400-600 nm sized spherical particles. At low voltages (300-800 V), the CL emission of 100 nm sized particles is much stronger than that of 400-600 nm sized ones. In contrast, the larger particles exhibit the higher CL emission intensity at high voltages (1-10 kV). Taking into consideration small spherical morphology and effective CL emission, Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ appears to be an efficient phosphor material for low voltage field emission display.     

Spectral properties of Nd-doped Sr3Ga2Ge4O14 crystal

Neodymium doped strontium gallogermanate crystals were grown successfully by the Bridgman technique. The linear thermal expansion coefficients for the c- and a-axes were measured as 5.8 × 10⁻⁶ °C⁻¹ and 6.5 × 10⁻⁶ °C⁻¹. Absorption spectra, and fluorescence spectra, as well as fluorescence decay curves of Nd³⁺-doped Sr₃Ga₂Ge₄O₁₄ crystal, have been recorded at room temperature and used to calculate the absorption and stimulated emission cross-sections. Based on the Judd-Ofelt theory, three intensity parameters were obtained. The luminescent quantum efficiency of the ⁴F_3/2 level was determined to be approximately 73.8% for this material. Compared with other Nd³⁺-doped laser crystals, Nd³⁺-doped Sr₃Ga₂Ge₄O₁₄ crystal displays special laser properties due to its disorder structure.     

High temperature ferromagnetism of the vacuum-annealed (In1−xFex)2O3 powders

(In_1−xFe_x)₂O₃ (x = 0.02, 0.05, 0.2) powders were prepared by a solid state reaction method and a vacuum annealing process. A systematic study was done on the structural and magnetic properties of (In_1−xFe_x)₂O₃ powders as a function of Fe concentration and annealing temperature. The X-ray diffraction and high-resolution transmission electron microscopy results confirmed that there were not any Fe or Fe oxide secondary phases in vacuum-annealed (In_1−xFe_x)₂O₃ samples and the Fe element was incorporated into the indium oxide lattice by substituting the position of indium atoms. The X-ray photoelectron spectroscopy revealed that both Fe²⁺ and Fe³⁺ ions existed in the samples. Magnetic measurements indicated that all samples were ferromagnetic with the magnetic moment of 0.49-1.73 μ_B/Fe and the Curie temperature around 783 K. The appearance of ferromagnetism was attributed to the ferromagnetic coupling of Fe²⁺ and Fe³⁺ ions via an electron trapped in a bridging oxygen vacancy.