Effects of growth temperature on the properties of ZnO/GaAs prepared by metalorganic chemical vapor deposition

A series of ZnO films were grown on GaAs(0 0 1) substrates at different growth temperatures in the range 250–720°C by metalorganic chemical vapor depostion. Field emission scanning electron microscopy was utilized to investigate the surface morphology of ZnO films. The crystallinity of ZnO films was investigated by the double-crystal X-ray diffractometry. The optical and electrical properties of ZnO films were also investigated using room-temperature photoluminescence and Hall measurements. Arrhenius plots of the growth rate versus reciprocal temperature revealed the kinetically limited growth behavior depending on the growth temperature. It was found that the surface morphology, structural, optical and electrical properties of the films were improved with increasing growth temperature to 650°C. All the properties of the film grown at 720°C were degraded due to the decomposition of ZnO film.     

Growth of nitrogen-doped p-type ZnO films by spray pyrolysis and their electrical and optical properties

Nitrogen-doped ZnO films were deposited on silicon (1 0 0) substrate using zinc acetate and ammonium acetate aqueous solution as precursors by ultrasonic spray pyrolysis. Successful p-type doping can be realized at optimized substrate temperature. The p-type ZnO films show excellent electrical properties such as hole concentration of 10¹⁸ cm⁻³, hole mobility of 10² cm² V⁻¹ s⁻¹ and resistivity of 10⁻² Ω cm. In the photoluminescence measurement, a strong near-band-edge emission was observed, while the deep-level emission was almost undetectable in both undoped and N-doped ZnO films. The growth and doping mechanism of N-doped ZnO films were discussed.     

Microstructural characteristics and crystallographic evolutions of Ga-doped ZnO films grown on sapphire substrates at high temperatures by RF magnetron sputtering

The microstructural characteristics and crystallographic evolutions of Ga-doped ZnO (GZO) films grown at high temperatures were examined by X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM). The GZO films with various film thicknesses were grown on (0 0 0 1) Al₂O₃ substrates at 750 °C by RF magnetron sputtering using a 2 wt% Ga-doped ZnO single target. The (0 0 0 2) ZnO peaks in the XRD patterns shifted to a higher angle with increasing film thickness and an additional (1 0 1¯ 1) ZnO peak was observed in the final stage of film growth. HRTEM showed the epitaxial growth of GZO films in the initial growth stage and the formation of surface protrusions in the intermediate stage due to elastic relaxation. The surface protrusions consisted of {1 0 1¯ 1}, {1 0 1¯ 3}, and {0 0 0 2} planes. After the surface protrusions had formed, a GZO film with many c-axis tilted grains formed due to plastic relaxation, where the tilted grain boundaries had an angle of 62° to the substrate. The formation of the protrusions and c-axis tilted grains was closely related to the strain status of the film induced by Ga incorporation, high-temperature growth and a high film thickness.     

Synthesis and optical properties of purified translucent,orthorhombic boron nitride films

Large-area (>1 cm²) freestanding translucent orthorhombic boron nitride (oBN) films have been synthesized by magnetron sputtering at a low radio-frequency power of 120 W. The structural characterizations were performed by means of X-ray diffraction, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. It is demonstrated that oBN is a direct band gap semiconductor (E_g∼3.43 eV). Excited by ultraviolet laser (wavelength at 325 nm), the oBN films emit strong white light, which can be seen by the naked eyes in the dark. In the photoluminescence spectrum, besides the ultraviolet near-band-edge radiative recombination emission, there are three visible emission bands (centered at 400, 538, and 700 nm) arising from the defect-related deep-level centers of oBN, which are mixed to form the white light emission. The hardness and elastic modulus of oBN films are 11.5 and 94 GPa, respectively, examined by nanoindentation measurements.     

Influence of oxygen/argon ratio on structural,electrical and optical properties of Ag-doped ZnO thin films

Ag-doped ZnO (ZnO:Ag) thin films were deposited on quartz substrates by radio frequency magnetron sputtering technique. The influence of oxygen/argon ratio on structural, electrical and optical properties of ZnO:Ag films has been investigated. ZnO:Ag films gradually transform from n-type into p-type conductivity with increasing oxygen/argon ratio. X-ray photoelectron spectroscopy measurement indicates that Ag substitutes Zn site (Ag_Zn) in the ZnO:Ag films, acting as acceptor, and being responsible for the formation of p-type conductivity. The presence of p-type ZnO:Ag under O-rich condition is attributed to the depression of the donor defects and low formation energy of Ag_Zn acceptor. The I–V curve of the p-ZnO:Ag/n-ZnO homojunction shows a rectification characteristic with a turn-on voltage of ∼7 V.     

Structural,electrical and optical properties of SnO2 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

SnO₂ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates at different substrate temperatures (500–800 °C) by metalorganic chemical vapor deposition (MOCVD). Structural, electrical and optical properties of the films have been investigated. The films deposited at 500 and 600 °C are epitaxial SnO₂ films with orthorhombic columbite structure, and the HRTEM analysis shows a clear epitaxial relationship of columbite SnO₂(1 0 0)||YSZ(1 0 0). The films deposited at 700 and 800 °C have mixed-phase structures of rutile and columbite SnO₂. The carrier concentration of the films is in the range from 1.15×10¹⁹ to 2.68×10¹⁹ cm⁻³, and the resistivity is from 2.48×10⁻² to 1.16×10⁻² Ω cm. The absolute average transmittance of the films in the visible range exceeds 90%. The band gap of the obtained SnO₂ films is about 3.75–3.87 eV.     

Structural and optical properties of Zn(Mg,Cd)O alloy films grown by remote-plasma-enhanced MOCVD

We report the structural and optical properties of wurtzite-structure Zn(Mg,Cd)O ternary alloys. Wurtzite (0 0 0 1) Zn_1−xCd_xO and Mg_yZn_1−yO films were grown on (11–20) sapphire substrates using remote-plasma-enhanced metalorganic chemical vapor deposition. The large bowing parameters of Zn_1−xCd_xO and Mg_yZn_1−yO ternary alloys are 3.0 and 3.5, respectively, which reflects the large difference of each binary’s electronegativity. We have analyzed the broadening of photoluminescence (PL) in Zn(Mg,Cd)O alloys on alloy content by taking into account the statistical alloy fluctuation and the localization of the exciton, and have clarified that the localization of the exciton strongly affects to PL full-width at half-maximum (FWHM) in Zn(Mg,Cd)O alloys. The alloy broadenings in steady-state PL of Zn(Mg,Cd)O alloys are in good agreement with the calculated tendency by the theoretical model based on the statistical alloy fluctuation, while PL FWHM of Zn_1−xCd_xO is three times larger than the calculated results. Moreover, as another way to confirm alloy broadening, we also have done time-resolved PL measurements and derived the localized depth of the exciton in ZnO-based system, indicating a good agreement with the tendency of PL FWHM broadening.     

Analysis of the growth of RF sputtered ZnO thin films using the optical reflective second harmonic generation

Reflective second harmonic generation (RSHG) is used to analyze the growth condition of poly crystal zinc oxide (ZnO) film with a c-axis orientation, grown on the Si substrate by RF magnetron sputtering technique. It elucidates physical phenomena exhibited by growing ZnO thin films. Connecting with analytical results of the characteristic parameters derived from the X-ray patterns and SEM images, the relationship between the RSHG intensity and the substrate temperature reveals that the effect of the grain boundaries is the domination of the RSHG mechanism. The inclined structures of ZnO films on the Si substrate are explained with reference to these RSHG patterns.     

Crystallographic,optical and magnetic properties of Co‐doped ZnO thin films synthesized by sol gel route

ZnO thin films with various Co doping levels (0%, 1%, 3%, 5%, 8%, respectively) have been synthesized by sol gel spin coating method on glass substrates. XRD and XPS studies of the films reveal that cobalt ions are successfully doped into ZnO crystal lattice without changing the hexagonal wurtzite structure. The morphologies are studied by SEM and AFM and show wrinkle network structures with uniform size distribution. With Co doping concentration increasing, the wrinkle network width decreases gradually. The transmittance spectra indicate that Co doping can effectively reduce the optical bandgap of ZnO thin films. Photoluminescence show that all samples have ultraviolet, violet and green emission. When Co doping concentration increases up to 5%, the intensity of violet emission is greatly increased and a strong deep blue emission centered at 439 nm appears. The ferromagnetism of all samples was observed at room temperature. The emission mechanisms and ferromagnetism origination are discussed in detail. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of hydrogen on structural and optical properties of low temperature polycrystalline Ge films deposited by RF magnetron sputtering

To improve the properties of polycrystalline Ge thin films, which are a candidate material for the bottom cells of low cost monolithic tandem solar cells, ∼300 nm in situ hydrogenated Ge (Ge:H) thin films were deposited on silicon nitride coated glass by radio-frequency magnetron sputtering. The films were sputtered in a mixture of 15 sccm argon and 10 sccm hydrogen at a variety of low substrate temperatures (T_s)≤450 °C. Structural and optical properties of the Ge:H thin films were measured and compared to those of non-hydrogenated Ge thin films deduced in our previous work. Raman and X-ray diffraction spectra revealed a structural evolution from amorphous to crystalline phase with increase in T_s. It is found that the introduction of hydrogen gas benefits the structural properties of the polycrystalline Ge film, sputtered at 450 °C, although the onset crystallization temperature is ∼90 °C higher than in those sputtered without hydrogen. Compared with non-hydrogenated Ge thin films, hydrogen incorporated in the films leads to broadened band gaps of the films sputtered at different T_s.     

Enhancement of near-band edge photoluminescence of ZnO thin films by employing MgF2 buffer layer

ZnO/MgF₂/ZnO sandwich structure films were fabricated. The effects of a buffer layer on structure and optical properties of ZnO films were investigated by X-ray diffraction, photoluminescence, optical transmittance and absorption measurements. Measurement results showed that the buffer layer had the effects of improving the quality of ZnO films and releasing the residual stresses in the films. The near-band edge emissions of ZnO films deposited on the MgF₂ buffer layer were significantly enhanced compared with those deposited on bare substrate due to the smaller lattice mismatch between MgF₂ and ZnO than that between fused silica and ZnO.     

Microstructure and ferroelectric properties of BaTiO3 films on LaNiO3 buffer layers by rf sputtering

We have fabricated LaNiO₃ and BaTiO₃ films using the rf sputtering method. The LaNiO₃ were deposited on Si substrates, demonstrating a (1 0 0) highly oriented structure and nanocrystalline characteristic with a grain size of 30 nm. The BaTiO₃ thin films were deposited on the LaNiO₃ buffer layers, and have exhibited a (1 0 0) texture with a thickness of 400 nm. A smooth interface is obtained between the LaNiO₃ bottom electrode and the BaTiO₃ film from cross-section observations by scanning electron microscopy. The bi-layer films show a dense and column microstructure with a grain size of 60 nm. Ferroelectric characterizations have been obtained for the BaTiO₃ films. The remnant polarization and coercive field are 2.1 μC/cm² and 45 kV/cm, respectively. The leak current measurements have shown a good insulating property.     

Morphological,structural and electrical investigations on non-polar a-plane ZnO epilayers

We report on the growth of non-polar a-plane ZnO by CVD on r-plane-sapphire-wafers, a-plane GaN-templates and a-plane ZnO single-crystal substrates. Only the homoepitaxial growth approach leads to a Frank–van-der–Merwe growth mode, as shown by atomic force microscopy. The X-ray-diffraction spectra of the homoepitaxial thin films mirror the excellent crystalline quality of the ZnO substrate. The morphological and the structural quality of the homoepitaxial films is comparable to the best results for the growth on c-plane ZnO-substrates. The impurity incorporation, especially of group III elements, seems to be reduced when growing on the non-polar a-plane surface compared to the c-plane films as demonstrated by secondary ion mass spectrometry (SIMS). Optical properties have been investigated using low temperature photoluminescence measurements. We employed capacitance–voltage measurements (C–V) to measure the background carrier density and its profile from substrate/film interface throughout the film to the surface. In thermal admittance spectroscopy (TAS) specific traps could be distinguished, and their thermal activation energies and capture cross sections could be determined.     

Fabrication of Zn/ZnO nanocables through thermal oxidation of Zn nanowires grown by RF magnetron sputtering

Fabrication of Zn/ZnO nanocables by thermal oxidation of Zn nanowires grown by RF magnetron sputtering is reported. Single crystalline Zn nanowires could be grown by controlling supersaturation of source material through the adjustment of temperature and Zn RF power. X-ray diffraction and high-resolution transmission electron microscopy showed that surfaces of these Zn nanowires, grown along the [0 1 0] direction, gradually oxidized inward the Zn core to form coaxial Zn/ZnO nanocables in the subsequent oxidation at 200 °C. In the Zn/ZnO nanocable, epitaxial relations of [1 0 0]_Zn//[1 0 0]_ZnO, and (0 0 1)_Zn//(0 0 1)_ZnO existed at the interface between the Zn core and ZnO shell. A number of dislocations were also observed in the interface region of the Zn/ZnO nanocable, which are attributed to large differences in the lattice constants of Zn and ZnO. With further increasing the oxidation temperature over 400 °C, Zn nanowires were completely oxidized to form polycrystalline ZnO nanowires. The results in this study suggest that coaxial Zn/ZnO nanocable can be fabricated through controlled thermal oxidation of Zn nanowires, yielding various cross-sectional areal fractions of Zn core and ZnO shell.     

Growth and optical absorption spectra of ZnO films grown by pulsed laser deposition

ZnO films on Al₂O₃ substrate were grown by using a pulsed laser deposition method. Through photoluminescence (PL) and X-ray diffraction (XRD) measurements, the optimum growth conditions for the ZnO growth were calculated. The results of the XRD measurement indicate that ZnO film was strongly oriented to the c-axis of hexagonal structure and epitaxially crystallized under constraints created by the substrate. The full-width half-maximum for a theta curve of the (0 0 0 2) peak was 0.201°. Also, from the PL measurement, the grown ZnO film was observed to be a free exciton, which indicates a high quality of epilayer. The Hall mobility and carrier density of the ZnO film at 293 K were estimated to be 299 cm²/V sec and , respectively. The absorption spectra revealed that the temperature dependence of the optical band gap on the ZnO films was − .     

Synthesis and optical properties of Ce-doped ZnO hexagonal nanoplatelets

Single crystalline Ce-doped ZnO hexagonal nanoplatelets are successfully synthesized. Zinc acetate, cerium nitrate, potassium hydroxide and poly vinyl alcohol were mixed together and transferred to a 100 mL Teflon-lined stainless steel autoclave kept at 150 °C for 24 h. The obtained precipitant is calcined at 600 °C. The morphology and microstructure were determined by field emission scanning electron microscopy (FE-SEM), X-ray diffraction transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX) and photoluminescence (PL) spectroscopy. The investigation confirmed that the products were of the wurtzite structure of ZnO. The doped hexagonal nanoplatelets have edge length 25 nm and thickness 11 nm. EDX result showed that the amount of Ce in the product is about 15%. Photoluminescence of these doped hexagonal nanoplatelets exhibits a blue shift and weak ultraviolet (UV) emission peak, compared with pure ZnO, which may be induced by Ce-doping. The growth mechanism of the doped hexagonal nanoplatelets was also discussed.     

Structural and electrical characterizations of single tetragonal FeSe on Si substrate

(0 0 l)-Oriented FeSe thin films were successfully fabricated by metal organic chemical vapor deposition on Si substrate with large thermal mismatch. X-ray diffraction and X-ray photoelectron spectroscopy measurements indicate that the films are of single tetragonal phase FeSe. Hysteresis loop indicates that the FeSe structure is ferromagnetic at room temperature with coercive force of 260 Oe. The FeSe films show p-type conduction with carrier concentration of 10²¹ cm⁻³, and the anomalous Hall effect was discussed.     

Structural and optical properties of quaternary AlInGaN epilayers grown by MOCVD with various TMGa flows

AlInGaN quaternary epilayers have been grown with various TMGa flows by metalorganic chemical vapor deposition to investigate the influence of growth rate on the structural and optical properties. Triple-axis X-ray diffraction measurements show AlInGaN epilayers have good crystalline quality. Photoluminescence (PL) measurements show that the emission intensity of AlInGaN epilayers is twenty times stronger than that of AlGaN epilayer with comparable Al content. V-shaped pits are observed at the surface of AlInGaN epilayers by atomic force microscopy (AFM) and transmission electron microscopy (TEM). High growth rate leads to increased density and size of V-shaped pits, but crystalline quality is not degraded.     

Growth and optical properties of high-density InN nanodots

High density InN/GaN nanodots were grown by pulsed mode (PM) metal–organic chemical vapor deposition (MOCVD). InN nanodots density of up to ∼5×10¹⁰ cm⁻² at a growth temperature of 550 °C was achieved. The high diffusion activation energy of 2.65 eV due to high NH₃ flow rate generated more reactive nitrogen adatoms on the growth surface, and is believed to be the main reason for the growth of high density InN nanodots. In addition, an anomalous temperature dependence of the PL peak energy was observed for high density InN nanodots. The high carrier concentration, due to high In vacancy (V_In) in the InN nanodots, thermally agitated to the conduction band. As the measurement temperature increased, the increase of Fermi energy resulted in blue-shifted PL peak energy. From the Arrhenius plot of integrated PL intensity, the thermal activation energy for the PM grown InN nanodots was estimated to be E_a∼51 meV, indicating strong localization of carriers in the high density InN nanodots.     

Properties of Si-rich SiO2 films by RF magnetron sputtering

Si-rich silicon oxide (SiO_x, 1<x<2) films were prepared by RF magnetron reactive sputtering or co-sputtering on the Si(1 1 1) substrates. X-ray diffraction patterns showed that the peak of silicon nanocrystals (NCs), separated from SiO_x films, had (1 1 1) preferred orientation. The results of scanning electron microscopy indicated the Si NCs uniting into clusters. We demonstrated that the photoluminescence (PL) peaks at 650 nm was caused by defect center. In particular, we discussed the correlation between the PL and the structure of SiO_x films. The mean size of the Si NCs was estimated to be about 3 nm by the PL peak position.