Crystal growth, characterization and spectroscopic study of europium-doped NaY(PO3)4

Europium-doped NaY(PO₃)₄ single crystals have been synthesized by the flux method with sizes around 1 mm³. The unit cell parameters at room temperature refined by X-ray powder diffraction are a=7.1510(4) Å; b=13.0070(8) Å; c=9.6973(2) Å; β=90.606(3)°, Z=4 with the space group P2₁/n in monoclinic system. The present single crystals have a needle shape, they are elongated along the a crystallographic direction, and their size is in the 500 μm–1 mm range. The linear thermal expansion tensor parameters were determined, being the maximum value along the b direction, 16.1×10⁻⁶ K⁻¹ and the minimum along the a direction being 11.7×10⁻⁶ K⁻¹. The IR vibration modes attributed to the group P–O are consistent with the crystallographic data concerning the chain aspect of the phosphate anion. This material melts incongruently at 1141 K. Intense visible emissions attributed to Eu^{3+ 5}D₀→⁷F₁, ⁵D₀→⁷F₂ and ⁵D₀→⁷F₄, electronic transitions have been observed after pumping at 355 nm at room temperature.     

Hydrothermal crystal growth of fresnoite

The growth of fresnoite, Ba₂TiSi₂O₈, by hydrothermal synthesis has led to spontaneous generation of large, (4-5 mm) optically clear crystals from 6 M KF mineralizer solutions. Growth was achieved at relatively low synthesis temperatures (575 °C) comparative to fresnoite synthesis by Czochralski or flux methods. Bulk crystal growth possibilities were explored by transport reactions performed in both fluoride and hydroxide mineralizers with 25-45 °C temperature gradients. Growth rates of 0.14×0.19×0.22 mm³/week were established in 6 M KOH, which is significantly slower than standard hydrothermal rates of 1 mm/week. Although relatively slow, the hydrothermal method has been demonstrated as a synthesis route to high quality single crystals of fresnoite.     

Crystallographic and dielectric properties of flux grown (B′B″: InNb, InTa, YbNb, YbTa and MgW) single crystals

Single crystals of PbIn_1/2Nb_1/2O₃ (PIN), PbIn_1/2Ta_1/2O₃ (PIT), PbYb_1/2Nb_1/2O₃ (PYN), PbYb_1/2Ta_1/2O₃ (PYT) and PbMg_1/2W_1/2O₃ (PMW) have been grown by the flux method. The PbO-based solvents were used. Transparent, light yellow and arrow like shaped PIN and PIT crystals of the perovskite structure were obtained. Small amounts of red and of octahedron habit PIN and PIT crystals of the pyrochlore type were simultaneously grown. In the case of PYN, PYT and PMW only the crystals of the perovskite structure have been grown. The transparent and brown PYN and PYT crystals of octahedron habit were obtained. The transparent, light yellow and of octahedron or truncated octahedron shape PMW crystals were grown. The crystals were characterised by X-ray and dielectric studies. They showed that as-grown PIN crystals are nearly disordered, exhibit the rhombohedral distortion of the pseudo-perovskite unit cell and reveal relaxor behaviour. The partially ordered PIT crystals show monoclinic distortion and undergo antiferroelectric–paraelectric phase transition. The PYN, PYT and PMW single crystals, characterised by chemical order in the B′/B″ ion sublattice, exhibit orthorhombic symmetry and undergo the first-order antiferroelectric–paraelectric phase transitions.     

Recent achievements in AMMONO-bulk method

In this paper we present progress made recently in the development of the growth of truly bulk GaN crystals by the ammonothermal method in basic environment. High quality 2-in c-plane GaN seeds are shown. Non-polar wafers can also be cut out from thick GaN crystals grown by ammonothermal method. Perfect crystallinity manifests in very narrow peaks in X-ray rocking curves (the full width at half maximum equals about 15 arcsec). GaN epilayers deposited on these substrates exhibit intrinsic narrow exciton lines, which are very sensitive to the optical selection rules typical for hexagonal symmetry, proving the truly non-polar character of such AMMONO-GaN substrates. Other challenges like homogenous insulating properties or high p-type conductivity have been also accomplished by means of ammonothermal method. Semi-insulating crystals of resistivity up to 10¹¹ Ω cm and p-type conductivity within hole concentration up to 10¹⁸ cm⁻³ are already available in diameters up to 1.5-in.     

Growth of (CH3)2NH2CuCl3 single crystals using evaporation method with different temperatures and solvents

The bulk single crystals of low-dimensional magnet (CH₃)₂NH₂CuCl₃ (DMACuCl₃ or MCCL) are grown by a slow evaporation method with different kinds of solvents, different degrees of super-saturation of solution and different temperatures of solution, respectively. Among three kinds of solvent, methanol, alcohol and water, alcohol is found to be the best one for growing MCCL crystals because of its structural similarity to the raw materials and suitable evaporation rate. The best growth temperature is in the vicinity of 35 °C. The problem of the crystals deliquescing in air has been solved through recrystallization process. The crystals are characterized by means of X-ray diffraction, specific heat and magnetic susceptibility.     

Czochralski-growth of germanium crystals containing high concentrations of oxygen impurities

Oxygen-containing germanium (Ge) single crystals with low density of grown-in dislocations were grown by the Czochralski (CZ) technique from a Ge melt, both with and without a covering by boron oxide (B₂O₃) liquid. Interstitially dissolved oxygen concentrations in the crystals were determined by the absorption peak at 855 cm⁻¹ in the infrared absorption spectra at room temperature. It was found that oxygen concentration in a Ge crystal grown from melt partially or fully covered with B₂O₃ liquid was about 10¹⁶ cm⁻³ and was almost the same as that in a Ge crystal grown without B₂O₃. Oxygen concentration in a Ge crystal was enhanced to be greater than 10¹⁷ cm⁻³ by growing a crystal from a melt fully covered with B₂O₃; with the addition of germanium oxide powder, the maximum oxygen concentration achieved was 5.5×10¹⁷ cm⁻³. The effective segregation coefficients of oxygen in the present Ge crystal growth were roughly estimated to be between 1.0 and 1.4.     

Chemically assisted vapour transport for bulk ZnO crystal growth

A chemically assisted vapour phase transport (CVT) method is proposed for the growth of bulk ZnO crystals. Thermodynamic computations have confirmed the possibility of using CO as a sublimation activator for enhancing the sublimation rate of the feed material in a large range of pressures (10⁻³ to 1 atm) and temperatures (800–1200 °C). Growth runs in a specific and patented design yielded single ZnO crystals up to 46 mm in diameter and 8 mm in thickness, with growth rates up to 400 μm/h. These values are compatible with an industrial production rate. N type ZnO crystals (μ=182 cm²/(V s) and n=7 10¹⁵ cm⁻³) obtained by this CVT method (Chemical Vapour Transport) present a high level of purity (10–30 times better than hydrothermal ZnO crystals), which may be an advantage for obtaining p-type doped layers ([Li] and [Al] <10⁺¹⁵ cm⁻³). Structural (HR-XRD), defect density (EPD), electrical (Hall measurements) and optical (photoluminescence) properties are presented.     

Crystal growth of KInO2 from a hydroxide flux

Single crystals of KInO₂ were obtained from a reactive potassium hydroxide flux at 700 °C. KInO₂ crystallizes in the R-3m crystal system with a=3.2998(10) Å, c=18.322(10) Å and V=172.78(12) Å³. The crystal structure is isotypic with that of α-NaFeO₂ and consists of the (1 1 1) layers being occupied alternately by KO₆ and InO₆ octahedra. Three different AInO₂ structure types are discussed.     

Growth and Raman spectroscopic characterization of As4S4 (II) single crystals

As described by Kutoglu (1976 [16]), single crystals of As₄S₄ (II) phase have been grown using a new two-step synthesis that drastically increases the reproducibility that is attainable in synthetic experiments. First, through photo-induced phase transformation, pararealgar powder is prepared as a precursor instead of AsS melt. Then it is dissolved and recrystallized from CS₂ solvent. Results show that single crystals of the As₄S₄ (II) phase were obtained reproducibly through the dissolution–recrystallization process. Single crystals of As₄S₄ (II) obtained using this method were translucent and showed a uniform yellow-orange color. The crystal exhibits a platelet-like shape as a thin film with well-developed faces (0 1 0) and (0 1¯ 0). The grown crystals are as large as 0.50×0.50×0.01 mm. They were characterized using powder and single crystal X-ray diffraction techniques to confirm the phase identification and the lattice parameters. The As₄S₄ (II) phase crystallizes in monoclinic system with cell parameters a=11.202(4) Å, b=9.954(4) Å, c=7.142(4) Å, β=92.81(4)°, V=795.4(6) Å³, which shows good agreement with the former value. Raman spectroscopic studies elucidated the behavior of the substance and the relation among phases of tetra-arsenic tetrasulfide.     

Optical property analysis of CZT:In single crystals after annealing by a two-step method

Indium-doped Cd_1−xZn_xTe (CZT:In) single crystals were annealed by a two-step method, including a high-temperature step and a low-temperature step in sequence. IR transmittance spectrum, I–V curve and PL spectrum were used to characterize the CZT single crystals. After annealing, the opto-electrical properties of the CZT:In crystals were improved obviously. The average IR transmittance was remarkably increased by about 23%, and the resistivity was enhanced by as high as four orders of magnitude. In the PL spectra, the intensity of the (D⁰, X) peak prominently increased, and the full-width-at-half-maximum was reduced. Meanwhile, the intensity of the DAP peak decreased greatly, and the structure became practically indistinguishable from the background. Moreover, the intensity of the D_complex peak also decreased. The investigation shows that these improvements in the physical properties after annealing are due to variations in the micro-structures. The two-step annealing method can eliminate precipitates/inclusions, remove impurities, compensate Cd vacancies, decrease dislocations and reduce internal stress.     

Improvement of crystal quality in ammonothermal growth of bulk GaN

Several key improvements in crystal quality of bulk GaN grown by the ammonothermal method are presented. Full width at half maximum of (0 0 2) X-ray rocking curve was reduced to 53 and 62 arcsec for Ga-side and N-side, respectively. Transparent bulk GaN crystal was also demonstrated. Oxygen and sodium concentrations were reduced to mid-10¹⁸ and mid-10¹⁵ cm⁻³, respectively. We are currently searching for a growth condition that produces transparent bulk GaN with high structural quality and low impurities. Small-sized, semi-transparent GaN wafers were fabricated by slicing the grown bulk GaN crystals, which demonstrate the high feasibility of ammonothermal growth for production of GaN wafers.     

Growth and properties of KTP crystals from a new flux

High-quality KTiOPO₄ (KTP) crystals were grown by a top seeded solution growth (TSSG) method using K₈P₆O₁₉–BaF₂ as a flux. The volatility of different solvents, such as K₈P₆O₁₉ (K₈), K₈–NaF, K₈–KF, and K₈–BaF₂, was measured. These fluoride additives in K₈ fluxes and their compositional effects on the growth of KTP crystals were studied and discussed. The transmissivity and optical homogeneity of KTP crystals were also measured.     

Sublimation crystal growth of yttrium nitride

The sublimation–recombination crystal growth of bulk yttrium nitride crystals is reported. The YN source material was prepared by reacting yttrium metal with nitrogen at 1200 °C and 800 Torr total pressure. Crystals were produced by subliming this YN from the source zone, and recondensing it from the vapor as crystals at a lower temperature (by 50 °C). Crystals were grown from 2000 to 2100 °C and with a nitrogen pressure from 125 to 960 Torr. The highest rate was 9.64×10⁻⁵ mol/h (9.92 mg/h). The YN sublimation rate activation energy was 467.1±21.7 kJ/mol. Individual crystals up to 200 μm in dimension were prepared. X-ray diffraction confirmed that the crystals were rock salt YN, with a lattice constant of 4.88 Å. The YN crystals were unstable in air; they spontaneously converted to yttria (Y₂O₃) in 2–4 h. A small fraction of cubic yttria was detected in the XRD of a sample exposed to air for a limited time, while non-cubic yttria was detected in the Raman spectra for a sample exposed to air for more than 1 h.     

Crystal growth and luminescent properties of Pr-doped K(Y,Lu)3F10 single crystal for scintillator application

Pr1%:K(Y_1−xLu_x)₃F₁₀ (x=0, 0.2, 0.4) single crystals were grown by the μ-PD method. All the grown crystals were greenish and perfectly transparent without any inclusions or cracks. Radioluminescence spectra and decay kinetics of the Pr1%:K(Y,Lu)₃F₁₀ crystals were measured. Emission from the Pr³⁺ 5d–4f transition, peaking around 260 nm and of the decay time of around 22 ns were observed. The 5d–4f emission intensities of the Pr1%:K(Y,Lu)₃F₁₀ crystals were higher than that of the standard BGO scintillator.     

Large-size and high-quality Zn2TiO4 single crystal grown by the optical floating zone method

Crack-free and transparent Zn₂TiO₄ single crystals of 4–6 mm in diameter and 30 mm in length have been grown by the optical floating zone method. The powder X-ray diffraction (XRD) results show that the as-grown crystals have the spinel-type Zn₂TiO₄ structure. XRD² measurements on Zn₂TiO₄ wafers cut perpendicular to the growth direction display only one peak at 42.7°, which indicates that the Zn₂TiO₄ single crystals grow along the 〈4 0 0〉 direction (a-axis). The formation of bubble inclusions was effectively suppressed by lowering rotation rate. Transmission polarized-light microscopy results showed that as-grown crystals were free of low angle grain boundaries.     

Ca3N2 as a flux for crystallization of GaN

In this work Ca₃N₂ was investigated as a potential flux for crystallization of GaN. Melting temperature of the potential flux at high N₂ pressure evaluated by thermal analysis as 1380 °C is in good agreement with the theoretical prediction. It is shown that Ca₃N₂ present in the liquid gallium in small amount (1 at%) dramatically accelerates synthesis of GaN from its constituents. On the other hand, it does not influence significantly the rate of GaN crystallization from solution in gallium in temperature gradient for both unseeded and seeded configurations. However the habit and color of the spontaneously grown GaN crystals change drastically. For 10 mol% Ca₃N₂ content in the liquid Ga it was found that the GaN thick layer and GaN crystals (identified by micro-Raman scattering measurements) were grown on the substrate. For growth from molten Ca₃N₂ (100%) with GaN source, the most important observations were (i) GaN source material was completely dissolved in the molten Ca₃N₂ flux and (ii) after experiment, GaN crystals were found on the sapphire substrate.     

Growth and characterization of the nonlinear optical single crystal: l-lysine acetate

Single crystals of l-lysine acetate, an organic nonlinear optical (NLO) material, were grown by the controlled evaporation of its aqueous solutions. Its solubility in aqueous solution was determined gravimetrically. The grown crystals were characterized by the single-crystal diffraction, X-ray powder diffraction, Fourier transform infrared and Raman spectra. The structure analysis reveals that it belongs to the monoclinic crystallographic system, space group P2₁, with cell parameters: a=5.420(2) Å, b=7.542(4) Å, c=12.653(1) Å, β=91.73(1)°, Z=2 and V=516.8 Å³. Experiments of thermogravimetric (TG) and differential thermal analysis (DTA) were carried out to study its thermal properties. The optical behaviours, including transmission spectrum and second harmonic generation (SHG), were investigated to study its linear and NLO properties.     

Growth and scintillation properties of the Na2W2O7 crystal

The growth and scintillation properties of the Na₂W₂O₇ crystal are reported. The solid reaction between Na₂CO₃ and WO₃ is used to synthesise the Na₂W₂O₇ material. The Na₂W₂O₇ single crystal has been grown by the Bridgman method. And the Na₂W₂O₇ single crystal with sizes 14×7×6 mm³ has been achieved. The transmission spectra, the Ultraviolet fluorescence spectra and the X-ray excited luminescence spectra of the Na₂W₂O₇ crystal are measured. The measurement results show that the Na₂W₂O₇ crystal is a promising intrinsic scintillator.     

Growth and property of Zn-doped near-stoichiometric LiTaO3 crystal

Near-stoichiometric LiTaO₃ (SLT) and Zn-doped near-stoichiometric LiTaO₃ (Zn:SLT) crystals with 10–15 mm in diameter and 10 mm in length were grown by using TSSG technique with K₂O as the flux. The effect of adding amount of K₂O was discussed in the growing process. The crystals were characterized by inductively coupled plasma-optical emission (ICP-OES), X-ray diffraction (XRD) and differential thermal analysis (DTA). The lattice constants of Zn:SLT were smaller than those of SLT and Curie temperature was higher than that of SLT. It was found that Zn doping is an efficient way to improve the optical damage resistance ability of SLT crystal. Compared with SLT crystal, Zn:SLT exhibited a much higher optical damage threshold, more than 500 MW/cm², which was attributed to Zn self-compensated effect that formed the charge compensated complexes, (Zn_Ta)³⁻–3(Zn_Li)⁺ in SLT crystal.     

Thermodynamics of the Al–Ga–N2 system

The thermodynamic properties of the Al–Ga–N₂ system under high N₂ pressure up to 10 kbar and 1800 °C are investigated. On the basis of the experimental p–T growth conditions for (Al,Ga)N crystals, the standard Gibbs free energy as well as the standard enthalpy and entropy of formation of the Al_xGa_1−xN crystals as a function of composition x were calculated. The a_N2–T and x–T phase diagrams for (Al,Ga)N are presented.