Growth of GaN based structures on Si(1 1 0) by molecular beam epitaxy

The growth of GaN based structures on Si(1 1 0) substrates by molecular beam epitaxy using ammonia as the nitrogen precursor is reported. The structural, optical and electrical properties of such structures are assessed and are quite similar to the ones obtained on Si(1 1 1) in-spite of the very different substrate surface symmetry. A threading dislocation density of 3.7×10⁹ cm⁻² is evaluated by transmission electron microscopy, which is in the low range of typical densities obtained on up to 2 μm thick GaN structures grown on Si(1 1 1). To assess the potential of such structure for device realization, AlGaN/GaN high electron mobility transistor and InGaN/GaN light emitting diode heterostructures were grown and their properties are compared with the ones obtained on Si(1 1 1).     

Investigation of nonpolar (1 1 2¯ 0) a-plane ZnO films grown under various Zn/O ratios by plasma-assisted molecular beam epitaxy

Structural and optical properties of nonpolar a-plane ZnO films grown with different II/VI ratios on r-plane sapphire substrates by plasma-assisted molecular beam epitaxy were investigated. Even by increasing the II/VI ratio across the stoichiometric flux condition a consistent surface morphology of striated stripes along the ZnO 〈0 0 0 1〉 direction without any pit formation was observed, which is contrary to polar c-plane ZnO films. Root mean square surface roughness, full width at half maximum values of X-ray rocking curves, defect densities, and photoluminescence were changed with the II/VI ratio. The sample grown with stoichiometric flux condition showed the lowest value of rms roughness, the smallest threading dislocation and stacking fault densities of ∼4.7×10⁸ cm⁻² and ∼9.5×10⁴ cm⁻¹, respectively, and the highest intensity of D^oX peak. These results imply that the stoichiometric flux growth condition is suitable to obtain superior structural and optical properties compared to other flux conditions.     

Reduction of the dislocation density in molecular beam epitaxial CdTe(2 1 1)B on Ge(2 1 1)

The high dislocation density (2×10⁷/cm² for a thickness of 7 μm) in CdTe(2 1 1)B on Ge(2 1 1) has become a roadblock for the technological exploitation of this material. We present a systematic study of in situ and post-growth annealing cycles aimed at reducing it. An etch pit density of 2×10⁶/cm² was achieved by optimizing the growth conditions and annealing the samples in situ. This finding was corroborated by high-resolution X-ray diffraction, atomic force microscopy, photoluminescence and ellipsometry measurements.     

Surface and interfacial structure of epitaxial SrTiO3 thin films on (0 0 1) Si grown by molecular beam epitaxy

Effects of relaxation of interfacial misfit strain and non-stoichiometry on surface morphology and surface and interfacial structures of epitaxial SrTiO₃ (STO) thin films on (0 0 1) Si during initial growth by molecular beam epitaxy (MBE) were investigated. In situ reflection high-energy electron diffraction (RHEED) in combination with X-ray diffraction (XRD), atomic force microscopy (AFM), X-ray photoelectron spectrometry (XPS) and transmission electron microscopy (TEM) techniques were employed. Relaxation of the interfacial misfit strain between STO and Si as measured by in situ RHEED indicates initial growth is not pseudomorphic, and the interfacial misfit strain is relaxed during and immediately after the first monolayer (ML) deposition. The interfacial strain up to 15 ML results from thermal mismatch strain rather than lattice mismatch strain. Stoichiometry of STO affects not only surface morphology but interfacial structure. We have identified a nanoscale Sr₄Ti₃O₁₀ second phase at the STO/Si interface in a Sr-rich film.     

Growth of epitaxial ZnO films on Si (1 1 1) substrates with Cr compound buffer layer by plasma-assisted molecular beam epitaxy

Single crystalline ZnO film was grown on (1 1 1) Si substrate through employing an oxidized CrN buffer layer by plasma-assisted molecular beam epitaxy. Single crystalline characteristics were confirmed from in-situ reflection high energy electron diffraction, X-ray pole figure measurement, and transmission electron diffraction pattern, consistently. Epitaxial relationship between ZnO film and Si substrate is determined to be (0 0 0 1)_ZnO‖(1 1 1)_Si and [1 1 2¯ 0]_ZnO‖[0 1 1]_Si. Full-width at half-maximums (FWHMs) of (0 0 0 2) and (1 0 1¯ 1) X-ray rocking curves (XRCs) were 1.379° and 3.634°, respectively, which were significantly smaller than the FWHMs (4.532° and 32.8°, respectively) of the ZnO film grown directly on Si (1 1 1) substrate without any buffer. Total dislocation density in the top region of film was estimated to be ∼5×10⁹ cm⁻². Most of dislocations have a screw type component, which is different from the general cases of ZnO films with the major threading dislocations with an edge component.     

Growth of embedded ErAs nanorods on (4 1 1)A and (4 1 1)B GaAs by molecular beam epitaxy

The low solubility of Er in GaAs results in the formation of ErAs nanostructures when GaAs is grown with 5–6 at% Er/Ga ratio by molecular beam epitaxy on GaAs surfaces. For growth on the (4 1 1)A GaAs surface, cross-sectional scanning transmission electron microscopy images show the presence of ErAs nanorods embedded in a GaAs matrix extending along the [2 1 1] direction with a spacing of roughly 7 nm and a diameter of roughly 2 nm. Growth on the GaAs (4 1 1)B surface resulted in only nanoparticle formation. Variation of the polarized optical absorption with in-plane polarization angle is consistent with coupling to surface plasmon resonances of the semimetallic nanostructures.     

Heteroepitaxy of CdTe on tilting Si(2 1 1) substrates by molecular beam epitaxy

CdTe(2 1 1)B epilayers were grown on 3 in Si(2 1 1) substrates which misoriented 0–10° toward [1 1 1] by molecular beam epitaxy (MBE). The relationship of X-ray double-crystal rocking curve (XRDCRC) FWHM and deflection angle from CdTe(2 1 1) to Si(2 1 1) was studied. For 4.2–4.5 μm CdTe, the best value of FWHM 83 arcsec was achieved while deflection angle is 2.76°. A FWHM wafer mapping indicated a good crystalline uniformity of 7.4 μm CdTe on tilting Si(2 1 1), with FWHM range of 60–72 arcsec. The shear strains of these epilayers were analyzed, using reciprocal lattice points of symmetric and asymmetric reflections measured by high-resolution multi-crystal multi-reflection X-ray diffractometer (HRMCMRXD). It was found that the shear strain angle of epilayer is effectively reduced by using proper tilting Si(2 1 1) substrate. It was also proved that the lattice parameter of CdTe(2 1 1)B is affected by the shear strain and thermal strain.     

Ga assisted oxide desorption on GaAs(0 0 1) studied by scanning tunnelling microscopy

Native oxide removal on GaAs wafers under conventional thermal desorption causes severe surface degradation. Recently a new method of Ga assisted oxide removal has reported improved initial surface conditions. A precise dosing of Ga is required to optimise the oxide removal, however the effects of alternate temperatures on the desorption process effects the reaction kinetics. By using selected bias imaging, scanning tunnelling microscopy (STM) can be used to probe the underlying bulk whilst the native oxide is still present. Hence the effects of oxide removal on the surface can be identified during the native oxide desorption. By comparing Ga assisted oxide removal on both vicinal and off cut samples, the Ga adatom kinetics are shown to underpin the oxide removal process and a sample temperature in excess of 500 °C is necessary to optimise the procedure.     

Hydride-assisted growth of GaN nanowires on Au/Si(0 0 1) via the reaction of Ga with NH3 and H2

High quality, straight GaN nanowires (NWs) with diameters of 50 nm and lengths up to 3 μm have been grown on Si(0 0 1) using Au as a catalyst and the direct reaction of Ga with NH₃ and N₂:H₂ at 900 °C. These exhibited intense, near band edge photoluminescence at 3.42 eV in comparison to GaN NWs with non-uniform diameters obtained under a flow of Ar:NH₃, which showed much weaker band edge emission due to strong non-radiative recombination. A significantly higher yield of β-Ga₂O₃ NWs with diameters of ≤50 nm and lengths up to 10 μm were obtained, however, via the reaction of Ga with residual O₂ under a flow of Ar alone. The growth of GaN NWs depends critically on the temperature, pressure and flows in decreasing order of importance but also the availability of reactive species of Ga and N. A growth mechanism is proposed whereby H₂ dissociates on the Au nanoparticles and reacts with Ga giving Ga_xH_y thereby promoting one-dimensional (1D) growth via its reaction with dissociated NH₃ near or at the top of the GaN NWs while suppressing at the same time the formation of an underlying amorphous layer. The higher yield and longer β-Ga₂O₃ NWs grow by the vapor liquid solid mechanism that occurs much more efficiently than nitridation.     

Effect of arsenic species on the kinetics of GaAs nanowires growth by molecular beam epitaxy

GaAs nanowires (NWs) are grown on GaAs (1 1 1) B substrates in a molecular beam epitaxy system, by Au-assisted vapor–liquid–solid growth. We compare the characteristics of NWs elaborated with As₂ or As₄ molecules. In a wide range of growth temperatures, As₄ leads to growth rates twice faster than As₂. The shape of the NWs also depends on the arsenic species: with As₄, regular rods can be obtained, while pencil-like shape results from growth with As₂. From the analysis of the incoming fluxes, which contributes to the NWs formation, we conclude that the diffusion length of Ga adatoms along the NW sidewalls is smaller under As₂ flux as compared to that under As₄ flux. It follows that As₂ flux is favourable to the formation of radial heterostructures, whereas As₄ flux is preferable to maintain pure axial growth.     

Epitaxial growth of the CoFe2O4 film on SrTiO3 and its characterization

Cobalt ferrite (CoFe₂O₄) thin film is epitaxially grown on (0 0 1) SrTiO₃ (STO) by laser molecular beam epitaxy (LMBE). The growth modes of CoFe₂O₄ (CFO) film are found to be sensitive to laser repetition, the transitions from layer-by-layer mode to Stranski–Krastanov (SK) mode and then to island mode occur at the laser repetition of 3 and 5 Hz at 700 °C, respectively. The X-ray diffraction (XRD) results show that the CFO film on (0 0 1) SrTiO₃ is compressively strained by the underlying substrate and exhibits high crystallinity with a full-width at half-maximum of 0.86°. Microstructural studies indicate that the as-deposited CFO film is c-oriented island structure with rough surface morphology and the magnetic measurements reveal that the compressive strained CoFe₂O₄ film exhibits an enhanced out-of-plane magnetization (190 emu/cm³) with a large coercivity (3.8 kOe).     

CrO2 (1 0 0) and TiO2 (1 0 0) film heteroepitaxy on a BaF2 (1 1 1)/Si (1 0 0) substrate

Multi-domained heteroepitaxial rutile-phase TiO₂ (1 0 0)-oriented films were grown on Si (1 0 0) substrates by using a 30-nm-thick BaF₂ (1 1 1) buffer layer at the TiO₂–Si interface. The 50 nm TiO₂ films were grown by electron cyclotron resonance oxygen plasma-assisted electron beam evaporation of a titanium source, and the growth temperature was varied from 300 to 600 °C. At an optimal temperature of 500 °C, X-ray diffraction measurements show that rutile phase TiO₂ films are produced. Pole figure analysis indicates that the TiO₂ layer follows the symmetry of the BaF₂ surface mesh, and consists of six (1 0 0)-oriented domains separated by 30° in-plane rotations about the TiO₂ [1 0 0] axis. The in-plane alignment between the TiO₂ and BaF₂ films is oriented as [0 0 1] TiO₂ || BaF₂ or [0 0 1] TiO₂ || BaF₂ . Rocking curve and STM analyses suggest that the TiO₂ films are more finely grained than the BaF₂ film. STM imaging also reveals that the TiO₂ surface has morphological features consistent with the BaF₂ surface mesh symmetry. One of the optimally grown TiO₂ (1 0 0) films was used to template a CrO₂ (1 0 0) film which was grown via chemical vapor deposition. Point contact Andreev reflection measurements indicate that the CrO₂ film was approximately 70% spin polarized.     

AlGaN photodetectors grown on Si(1 1 1) by molecular beam epitaxy

The fabrication and characterisation of Al_xGa_1−xN (0x0.35) photodetectors grown on Si(1 1 1) by molecular beam epitaxy are described. For low Al contents (<10%), photoconductors show high responsivities (10A/W), a non-linear dependence on optical power and persistent photoconductivity (PPC). For higher Al contents the PPC decreases and the photocurrent becomes linear with optical power. Schottky photodiodes present zero-bias responsivities from 12 to 5 mA/W (x=0−0.35), a UV/visible contrast higher than 10³, and a time response of 20 ns, in the same order of magnitude as for devices on sapphire substrate. GaN-based p–n ultraviolet photodiodes on Si(1 1 1) are reported for the first time.     

Stacking faults blocking process in (1 1 −2 2) semipolar GaN growth on sapphire using asymmetric lateral epitaxy

We have succeeded in effectively stopping the propagation of basal stacking faults in (1 1 −2 2) semipolar GaN films on sapphire using an original epitaxial lateral overgrowth process. The growth conditions were chosen to enhance the growth rate along the [0 0 0 1] inclined direction. Thus, the crystal expands laterally until growth above the a-facet of the adjacent crystal seed, where the basal stacking faults emerge. The growth anisotropy was monitored using scanning electron microscopy. The faults filtering and improvement of crystalline quality were attested by transmission electron microscopy, X-ray diffraction and low temperature photoluminescence, which exhibits high intensity band-edge emission with low stacking faults related emission.     

Subtle interplay between polytypism and preferred growth direction alignment in GaN nanorods non-catalytically grown on Si(1 1 1) substrates by using hydride vapor phase epitaxy

GaN nanorods were grown on Si(1 1 1) substrates by using hydride vapor phase epitaxy, and the crystallographic characteristics associated with their preferred growth directions were investigated by utilizing synchrotron X-ray reciprocal space mapping in a grazing incidence geometry and scanning electron microscopy. Crystallographic analysis reveals that the nanorods containing both wurtzite and zinc blende phase tend to have narrower distribution of the preferred growth directions than those containing only wurtzite phase. This tendency is partly attributed to the subtle interplay between polytypism and the preferred growth directions of GaN nanorods.     

Controllable cubic and hexagonal GaN growth on GaAs(0 0 1) substrates by molecular beam epitaxy

Two kinds of GaN samples were grown on GaAs(0 0 1) substrates. One is grown on nitridized GaAs surface, the other is grown on nitridized AlAs buffer GaAs substrate. X-ray diffraction and photoluminescence measurements find that the GaN sample directly grown on GaAs substrate is pure cubic phase and those grown on AlAs buffer is pure hexagonal phase. The present study shows that the phase of GaN samples grown on GaAs substrates can be controlled using different buffer layers.     

MBE growth of PbSe thin film with a 9×10 cm etch-pits density on patterned (1 1 1)-oriented Si substrate

PbSe thin film was grown on a patterned Si substrate with (1 1 1)-orientation by molecular-beam epitaxy (MBE). On the mesa, a low dislocation density of 9×10⁵ cm⁻² was confirmed by the etch-pits density (EPD) wet-etching technique. The photoluminescence (PL) intensity at room temperature from the low dislocation PbSe film was much higher than that from the PbSe film grown on the planar area, which further indicated the high-quality of PbSe thin film grown on patterned Si substrate.     

Low-temperature growth of epitaxial (1 0 0) silicon based on silane and disilane in a 300 mm UHV/CVD cold-wall reactor

Epitaxial (1 0 0) silicon layers were grown at temperatures ranging from 500 to 800 °C in a commercial cold-wall type UHV/CVD reactor at pressures less than 7×10⁻⁵ Torr. The substrates were 300 mm SIMOX SOI wafers and spectroscopic ellipsometry was used to assess growth rates and deposition uniformities. High-resolution atomic force microscopy (AFM) was employed to verify the atomic terrace configuration that resulted from epitaxial step-flow growth. Deposition from disilane exhibited a nearly perfect reaction limit for low temperatures and high precursor flow rates (partial pressures) with measured activation energies of ≈2.0 eV, while a linear dependence of growth rate on precursor gas flow was found for the massflow-controlled regime. A similar behavior was observed in the case of silane with substantially reduced deposition rates in the massflow-limited regime and nearly a factor of 2 reduced growth rates deep in the reaction limited regime. High growth rates of up to 50 μm/h and non-uniformities as low as 1σ=1.45% were obtained in the massflow-limited deposition regime. Silicon layers as thin as 0.6 nm (4.5 atomic layers ) were deposited continuously as determined using a unique wet chemical etching technique as well as cross-sectional high-resolution transmission electron microscopy (HRTEM). In contrast, epitaxial silicon deposited in RPCVD at 10 Torr using disilane within the same temperature range showed imperfect reaction limitation. While activation energies similar to that of UHV/CVD were found, no partial pressure limitation could be observed. Furthermore, layers deposited using disilane in RPCVD exhibited a large number of defects that appeared to form randomly during growth. We attribute this effect to gas phase reactions that create precursor fragments and radicals—an effect that is negligible in UHV/CVD.     

Structural,electrical and optical properties of SnO2 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

SnO₂ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates at different substrate temperatures (500–800 °C) by metalorganic chemical vapor deposition (MOCVD). Structural, electrical and optical properties of the films have been investigated. The films deposited at 500 and 600 °C are epitaxial SnO₂ films with orthorhombic columbite structure, and the HRTEM analysis shows a clear epitaxial relationship of columbite SnO₂(1 0 0)||YSZ(1 0 0). The films deposited at 700 and 800 °C have mixed-phase structures of rutile and columbite SnO₂. The carrier concentration of the films is in the range from 1.15×10¹⁹ to 2.68×10¹⁹ cm⁻³, and the resistivity is from 2.48×10⁻² to 1.16×10⁻² Ω cm. The absolute average transmittance of the films in the visible range exceeds 90%. The band gap of the obtained SnO₂ films is about 3.75–3.87 eV.