YAl3(BO3)4: Crystal growth and characterization

The growth and characterization of YAl₃(BO₃)₄ (YAB), a potential nonlinear optical crystal for the fourth harmonic generation of Nd:YAG laser, was reported. Using top-seeded solution growth method, a YAB crystal with the dimensions of 16×16×18 mm³ was obtained from B₂O₃–Li₂O flux system. The advantages of this flux system and the growth process were discussed in detail. The as-grown YAB crystal was verified by powder X-ray diffraction. The transparency spectra indicated that the cut-off edge of the as-grown YAB was 170 nm. The fourth harmonic generation of a frequency doubled Nd:YAG laser, from 532 to 266 nm, was carried out with a YAB crystal doubler for the first time. Output pulse power obtained was 2.4 mW at 266 nm and the conversion efficiency from 532 to 266 nm was about 15.6%.     

In-situ visualization of a super-accelerated synthesis of zinc oxide nanostructures through CO2 laser heating

A simple growth technique capable of growing a variety of zinc oxide (ZnO) nanostructures with record growth rates of 25 μm/s is demonstrated. Visible lengths of ZnO nanowires, nanotubes, comb-like and pencil-like nanostructures could be grown by employing a focused CO₂ laser-assisted heating of a sintered ZnO rod in ambient air, in few seconds. For the first time, the growth process of nanowires was videographed, in-situ, on an optical microscope. It showed that ZnO was evaporated and presumably decomposed into Zn and oxygen by laser heating, reforming ZnO nanostructures at places with suitable growth temperatures. Analysis on the representative nanowires shows a rectangular cross-section, with a [0 0 0 1] growth direction. With CO₂ laser heating replacing furnace heating used conventionally, and using different reactants and forming gases, this method could be easily adopted for other semiconducting inorganic nanostructures in addition to ZnO.     

Cs2LiGdCl6 (Ce): New scintillation material

We investigated the scintillation properties of Cs₂LiGdCl₆:Ce³⁺ as a function of the Ce concentration. X-ray excited luminescence spectra of the scintillation material showed broad emission bands between 360 and 460 nm, with two overlapping peaks, due to the d→f transitions on Ce³⁺ ions. The samples provide good scintillation results. The energy resolution was found to be 5.0% (FWHM) at 662 keV for 10% Ce sample. Under γ-ray excitation, Cs₂LiGdCl₆:Ce³⁺ showed three exponential decay time components of about 130–200 ns decay time constant. The light output of the investigated samples was 20,000 photons/MeV for a 10% Ce concentration. The light output deviation from the linear response is within 7% between the energy range of 31 and 1333 keV. Overall, the scintillation properties confirm that Cs₂LiGdCl₆:Ce³⁺ single crystal is a promising candidate for medical imaging and radiation detection.     

Thermal-induced phase transition and assembly of hexagonal metastable In2O3 nanocrystals: A new approach to In2O3 functional materials

This paper reports on the thermal-induced performance of hexagonal metastable In₂O₃ nanocrystals involving in phase transition and assembly, with particular emphasis on the assembly for the preparation of functional materials. For In₂O₃ nanocrystals, the metastable phase was found to be thermally unstable and transform to cubic phase when temperature was higher than 600 °C, accompanied by assembly as well as evolution of optical properties, but the two polymorphs coexisted at the temperature ranging from 600 to 900 °C, during which the content of product phase and crystal size gradually increased upon increasing temperature. The assembly of In₂O₃ nanocrystals can be developed to fabricate In₂O₃ functional materials, such as various ceramic materials, or even desired nano- or micro-structures, by using metastable In₂O₃ nanocrystals as precursors or building blocks. The electrical resistivity of In₂O₃ conductive film fabricated by a hot-pressing route was as low as 3.72×10⁻³ Ω cm, close to that of In₂O₃ single crystal, which is important for In₂O₃ that is always used as conductive materials. The findings should be of importance for both the wide applications of In₂O₃ in optical and electronic devices and theoretical investigations on crystal structures.     

Structure and growth morphology of Gd2O3-doped CeO2 thin films

Gd₂O₃-doped CeO₂ (Gd_0.1Ce_0.9O_1.95, GDC) thin films were synthesized on (1 0 0) Si single crystal substrates by a reactive radio frequency magnetron sputtering technique. Structures and surface morphologies were characterized by X-ray diffraction (XRD), Atomic Force Microscopy (AFM) and one-dimensional power spectral density (1DPSD) analysis. The XRD patterns indicated that, in the temperature range of 200–700 °C, f.c.c. structured GDC thin films were formed with growth orientations varying with temperature—random growth at 200 °C, (2 2 0) textures at 300–600 °C and (1 1 1) texture at 700 °C. GDC film synthesized at 200 °C had the smoothest surface with roughness of R_rms=0.973 nm. Its 1DPSD plot was characterized with a constant part at the low frequencies and a part at the high frequencies that could be fitted by the f^−2.4 power law decay. Such surface feature and scaling behavior were probably caused by the high deposition rate and random growth in the GDC film at this temperature. At higher temperatures (300–700 °C), however, an intermediate frequency slope (−γ₂≈−2) appeared in the 1DPSD plots between the low frequency constant part and the high frequency part fitted by f⁻⁴ power law decay, which indicated a roughing mechanism dominated by crystallographic orientation growth that caused much rougher surfaces in GDC films (R_rms>4 nm).     

Structural,electrical and optical properties of SnO2 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

SnO₂ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates at different substrate temperatures (500–800 °C) by metalorganic chemical vapor deposition (MOCVD). Structural, electrical and optical properties of the films have been investigated. The films deposited at 500 and 600 °C are epitaxial SnO₂ films with orthorhombic columbite structure, and the HRTEM analysis shows a clear epitaxial relationship of columbite SnO₂(1 0 0)||YSZ(1 0 0). The films deposited at 700 and 800 °C have mixed-phase structures of rutile and columbite SnO₂. The carrier concentration of the films is in the range from 1.15×10¹⁹ to 2.68×10¹⁹ cm⁻³, and the resistivity is from 2.48×10⁻² to 1.16×10⁻² Ω cm. The absolute average transmittance of the films in the visible range exceeds 90%. The band gap of the obtained SnO₂ films is about 3.75–3.87 eV.     

Growth and property of Zn-doped near-stoichiometric LiTaO3 crystal

Near-stoichiometric LiTaO₃ (SLT) and Zn-doped near-stoichiometric LiTaO₃ (Zn:SLT) crystals with 10–15 mm in diameter and 10 mm in length were grown by using TSSG technique with K₂O as the flux. The effect of adding amount of K₂O was discussed in the growing process. The crystals were characterized by inductively coupled plasma-optical emission (ICP-OES), X-ray diffraction (XRD) and differential thermal analysis (DTA). The lattice constants of Zn:SLT were smaller than those of SLT and Curie temperature was higher than that of SLT. It was found that Zn doping is an efficient way to improve the optical damage resistance ability of SLT crystal. Compared with SLT crystal, Zn:SLT exhibited a much higher optical damage threshold, more than 500 MW/cm², which was attributed to Zn self-compensated effect that formed the charge compensated complexes, (Zn_Ta)³⁻–3(Zn_Li)⁺ in SLT crystal.     

Growth and microstructural features of laser ablated LiCoO2 thin films

Thin films of LiCoO₂ were prepared by pulsed laser deposition technique and the properties were studied in relation to the deposition parameters. The films deposited from a sintered composite target (LiCoO₂+Li₂O) in an oxygen partial pressure of 100 mTorr and at a substrate temperature of 300 °C exhibited preferred c-axis (0 0 3) orientation perpendicular to the substrate surface. The AFM data demonstrated that the films are composed of uniform distribution of fine grains with an average grain size of 80 nm. The grain size increased with an increase in substrate temperature. The (0 0 3) orientation decreased with increase in (1 0 4) orientation for the films deposited at higher substrate temperatures (>500 °C) indicating that the films’ growth is parallel to the substrate surface. The composition of the experimental films was analyzed using X-ray photoelectron spectroscopy (XPS). The binding energy peaks of Co(2p_3/2) and Co(2p_1/2) are, respectively, observed at 779.3 and 794.4 eV, which can be attributed to the Co³⁺ bonding state of LiCoO₂. The electrochemical measurements were carried out on Li//LiCoO₂ cells with a lithium metal foil as anode and LiCoO₂ film as cathode of 1.5 cm² active area using a Teflon home-made cell hardware. The Li//LiCoO₂ cells were tested in the potential range 2.6-4.2 V. Specific capacity as high as 205 mC/cm² μm was measured for the film grown at 700 °C. The growth of LiCoO₂ films were studied in relation to the deposition parameters for their effective utilization as cathode materials in solid-state microbattery application.     

Hydride-assisted growth of GaN nanowires on Au/Si(0 0 1) via the reaction of Ga with NH3 and H2

High quality, straight GaN nanowires (NWs) with diameters of 50 nm and lengths up to 3 μm have been grown on Si(0 0 1) using Au as a catalyst and the direct reaction of Ga with NH₃ and N₂:H₂ at 900 °C. These exhibited intense, near band edge photoluminescence at 3.42 eV in comparison to GaN NWs with non-uniform diameters obtained under a flow of Ar:NH₃, which showed much weaker band edge emission due to strong non-radiative recombination. A significantly higher yield of β-Ga₂O₃ NWs with diameters of ≤50 nm and lengths up to 10 μm were obtained, however, via the reaction of Ga with residual O₂ under a flow of Ar alone. The growth of GaN NWs depends critically on the temperature, pressure and flows in decreasing order of importance but also the availability of reactive species of Ga and N. A growth mechanism is proposed whereby H₂ dissociates on the Au nanoparticles and reacts with Ga giving Ga_xH_y thereby promoting one-dimensional (1D) growth via its reaction with dissociated NH₃ near or at the top of the GaN NWs while suppressing at the same time the formation of an underlying amorphous layer. The higher yield and longer β-Ga₂O₃ NWs grow by the vapor liquid solid mechanism that occurs much more efficiently than nitridation.     

Growth and photoluminescence properties of vertically aligned SnO2 nanowires

Vertically aligned SnO₂ nanowires (NWs) were grown for the first time by a vapor–liquid–solid method on c-sapphire with gold as a catalyst under Ar gas flow. Electron backscatter diffraction analysis indicated the NWs are single crystalline having the rutile structure, grow vertically along the [1 0 0] direction, and exhibit a consistent epitaxial relationship where lattice mismatch is estimated to be 0.3% along the SnO₂ [0 1 0] direction. The growth of these NWs is sensitive to many parameters, including growth duration, substrate type, source vapor concentration, and the thickness of the catalyst layer. Photoluminescence measurements at room temperature showed that the vertically aligned NWs exhibit an intense transition at 3.64 eV, a near band-edge transition which is rarely observed in SnO₂.     

Growth and Raman spectroscopic characterization of As4S4 (II) single crystals

As described by Kutoglu (1976 [16]), single crystals of As₄S₄ (II) phase have been grown using a new two-step synthesis that drastically increases the reproducibility that is attainable in synthetic experiments. First, through photo-induced phase transformation, pararealgar powder is prepared as a precursor instead of AsS melt. Then it is dissolved and recrystallized from CS₂ solvent. Results show that single crystals of the As₄S₄ (II) phase were obtained reproducibly through the dissolution–recrystallization process. Single crystals of As₄S₄ (II) obtained using this method were translucent and showed a uniform yellow-orange color. The crystal exhibits a platelet-like shape as a thin film with well-developed faces (0 1 0) and (0 1¯ 0). The grown crystals are as large as 0.50×0.50×0.01 mm. They were characterized using powder and single crystal X-ray diffraction techniques to confirm the phase identification and the lattice parameters. The As₄S₄ (II) phase crystallizes in monoclinic system with cell parameters a=11.202(4) Å, b=9.954(4) Å, c=7.142(4) Å, β=92.81(4)°, V=795.4(6) Å³, which shows good agreement with the former value. Raman spectroscopic studies elucidated the behavior of the substance and the relation among phases of tetra-arsenic tetrasulfide.     

Synthesis,growth and characterization of organic nonlinear optical bis-glycine maleate (BGM) single crystals

A new organic compound of bis-glycine maleate was synthesized in the alkaline medium of 10% ammonium hydroxide solution. The bulk single crystals of Bis-Glycine Maleate (BGM) have been grown by slow cooling method. The grown crystals were characterized by employing single crystal and powder X-ray diffraction, Fourier transform infrared, optical absorption spectral studies and thermo gravimetric analysis. The microhardness studies confirmed that the BGM has a fairly high Vicker’s hardness number value (41 kg mm⁻²) in comparison to other organic NLO crystals. Second harmonic generation efficiency of the crystal measured by Kurtz–Perry powder method using Nd:YAG laser is found to be comparable to that of potassium dihydrogen phosphate (KDP). Frequency dependent dielectric studies were carried out along the major growth axis.     

Crystal growth of KInO2 from a hydroxide flux

Single crystals of KInO₂ were obtained from a reactive potassium hydroxide flux at 700 °C. KInO₂ crystallizes in the R-3m crystal system with a=3.2998(10) Å, c=18.322(10) Å and V=172.78(12) Å³. The crystal structure is isotypic with that of α-NaFeO₂ and consists of the (1 1 1) layers being occupied alternately by KO₆ and InO₆ octahedra. Three different AInO₂ structure types are discussed.     

Lu5Ir4Si10 whiskers: Morphology,crystal structure,superconducting and charge density wave transition studies

Highly perfect single crystal whiskers of Lu₅Ir₄Si₁₀ were successfully grown out of the melt. Details of the surface and morphology of the whiskers are presented. X-ray diffraction data confirmed that the whisker structure has the same tetragonal P4/mbm space group symmetry as bulk single crystals with lattice parameters a=12.484(1) and c=4.190(2) Å. By means of field emission scanning electron microscopy, the morphology of the whiskers has been studied. Using a 4-circle X-ray diffractometer we found that whiskers grow along the c-axis direction and all side faces are oriented along the [1 1 0] direction. The mosaicity has been measured and is found to be almost perfect: below 0.15° along the c-axis. According to our transport measurements performed along the c-axis, the whiskers present a sharp superconducting transition at T_c=4.1 K and show a charge density wave (CDW) transition at 77 K. From the hysteresis of the temperature dependance of the electrical resistivity study, the CDW transition is found to be of first order.     

Growth and characterization of nanostructured Al2O3/YAG/ZrO2 hypereutectics with large surfaces under laser rapid solidification

The preparation of large bulk oxide eutectics with homogeneous and dense structure in nano-scale by melt growth method is a difficult challenge. Fully dense, homogeneous and crack-free ternary nanostructured Al₂O₃/YAG/ZrO₂ hypereutectic plate with large surface is successfully obtained by laser remelting. The hypereutectic in selected composition presents an ultra-fine eutectic-like microstructure consisting of alternating interpenetrating Al₂O₃, YAG and ZrO₂ lamellae with mean interphase spacing of about 150 nm, which is much smaller than the ternary eutectic composition grown at the same growth conditions. With the increase of laser scanning rate, the lamellar spacing is rapidly decreased. The minimum value obtained is 50 nm. The analysis indicates that the strong faceted growth behavior and cooperative branching of the component phases related with high entropies of fusion and large kinetic undercooling during laser rapid solidification are the primary formation reasons for the irregular eutectic growth morphology. Furthermore, the unique cellular microstructure with complex structure is also observed at high growth rate, and their formation mechanism and effect of the composition on the microstructure are discussed.     

Crystal growth and spectroscopic properties of erbium doped Lu2SiO5

A high optical quality erbium doped Lu₂SiO₅ single crystal has been grown by the Czochralski method. The distribution coefficient of Er³⁺ was measured to be ∼0.926. The absorption and emission spectra as well as the fluorescence decay curve of the excited state ⁴I_13/2 were measured at room temperature. The spectroscopic parameters were calculated using the Judd–Ofelt theory, and the J–O parameters Ω₂, Ω₄ and Ω₆ were found to be 4.451×10^-20, 1.614×10^-20 and 1.158×10^-20 cm², respectively. The room-temperature fluorescence lifetime of the Er³⁺⁴I_13/2→⁴I_15/2 transition was measured to be 7.74 ms. The absorption and emission cross-section as well as the gain cross-section in the eye-safe regime of 1400–1700 nm were also determined and discussed.     

Growth of polar axis oriented tetragonal Pb(Zr,Ti)O3 films on CaF2 substrates with transparent (La0.07Sr0.93)SnO3

Epitaxial (La_0.07Sr_0.93)SnO₃ [LSSO] films were deposited on CaF₂ substrates by pulse laser deposition. The (1 0 0)_c orientation of LSSO films was observed only on (1 1 0)CaF₂, whereas (1 1 0)_c orientation was found on (1 1 1)CaF₂ and (1 0 0)CaF₂. (0 0 1) polar axis oriented tetragonal Pb(Zr_0.35Ti_0.65)O₃ films were grown on the fabricated (1 0 0)_cLSSO∥(1 1 0)CaF₂ by pulsed metal organic chemical vapor deposition. The (0 0 1)Pb(Zr_0.35Ti_0.65)O₃∥(1 0 0)cLSSO∥(1 1 0)CaF₂ stack structure exhibited about 70% transparency with an adsorption edge of approximately 330 nm.     

Growth and characterization of Nd:CLNGG crystal

The disordered laser crystal neodymium-doped calcium lithium niobium gallium garnet (Nd:CLNGG) was successfully grown by the Czochralski method. Its thermal properties, including the average linear thermal expansion coefficient, thermal diffusion coefficient, specific heat, and thermal conductivity were measured, and continuous-wave (CW) laser performance at 1.06 μm was demonstrated. The maximum power of 1.48 W was achieved with corresponding optical conversion efficiency of 12.4% and slope efficiency of 16.2%.     

Ca3N2 as a flux for crystallization of GaN

In this work Ca₃N₂ was investigated as a potential flux for crystallization of GaN. Melting temperature of the potential flux at high N₂ pressure evaluated by thermal analysis as 1380 °C is in good agreement with the theoretical prediction. It is shown that Ca₃N₂ present in the liquid gallium in small amount (1 at%) dramatically accelerates synthesis of GaN from its constituents. On the other hand, it does not influence significantly the rate of GaN crystallization from solution in gallium in temperature gradient for both unseeded and seeded configurations. However the habit and color of the spontaneously grown GaN crystals change drastically. For 10 mol% Ca₃N₂ content in the liquid Ga it was found that the GaN thick layer and GaN crystals (identified by micro-Raman scattering measurements) were grown on the substrate. For growth from molten Ca₃N₂ (100%) with GaN source, the most important observations were (i) GaN source material was completely dissolved in the molten Ca₃N₂ flux and (ii) after experiment, GaN crystals were found on the sapphire substrate.     

Growth of epitaxial TmFeCuO4 thin films by pulsed laser deposition

Epitaxial thin films of TmFeCuO₄ with a two-dimensional triangular lattice structure were successfully grown on yttria-stabilized-zirconia substrates by pulsed laser deposition and ex situ annealing in air. The films as-deposited below 500 °C showed no TmFeCuO₄ phase and the subsequent annealing resulted in the decomposition of film components. On the other hand, as-grown films deposited at 800 °C showed an amorphous nature. Thermal annealing converted the amorphous films into highly (0 0 1)-oriented epitaxial films. The results of scanning electron microscopic analysis suggest that the crystal growth process during thermal annealing is dominated by the regrowth of non-uniformly shaped islands to the distinct uniform islands of hexagonal base.