Flux growth of PbMg1/3Ta2/3O3 single crystals

Single crystals of PbMg_1/3Ta_2/3O₃ (PMT) were grown by the flux method. The PbO–Pb₃O₄–B₂O₃ system was used as a solvent. Transparent and light yellow PMT single crystals of rectangular shape and dimensions up to 10×6×4 mm³ were obtained. For the applied growth conditions only, the crystals of the perovskite structure were grown. X-ray diffraction tests showed that at room temperature PMT exhibits cubic symmetry with lattice parameter a=4.042(1) Å. Dielectric studies pointed to relaxor properties of PMT. The characteristic broad and frequency-dependent maximum of dielectric permittivity was observed at 179.7 K (1 kHz).     

Environmental SEM investigation on surface defects in 0.92Pb(Zn1/3Nb2/3)O3–0.08PbTiO3 single crystal

In this paper, the technique of environmental scanning electron microscopy (ESEM) has been employed to investigate the surface defects of the (1 1 1) appearing face in 0.92Pb(Zn_1/3Nb_2/3)O₃–0.08PbTiO₃ (PZN–8%PT) crystals. From the ESEM images, we succeeded in observing and studying the growth hillocks and etch pits, low-angle grain boundaries, and sub-grain boundaries in (1 1 1) face, which were related to the generation of dislocation and stacking faults, respectively. On the other hand, an image of a unique multi-layer lamellar structure and fine step structure obtained in the (1 1 1) face reveals that the dominant fast growth mechanism of PZN–8%PT crystal grown by the flux method is a sub-step mechanism, unlike the screw dislocation growth mechanism.     

Half opened microtubes of NaYF4:Yb,Er synthesized in reverse microemulsion under solvothermal condition

NaYF₄:Yb,Er micro/nanocrystals with different sizes and morphologies such as nanospheres, short flexural nanorods, and half opened microtubes, were synthesized in reverse microemulsion under solvothermal condition using the quaternary reverse microemulsion system, CTAB/1-butanol/cyclohexane/aqueous solution. The X-ray diffraction analysis confirmed that cubic phase NaYF₄:Yb,Er can completely transform to hexagonal phase with increasing reaction time. The scanning electron microscope and transmission electron microscope images revealed that the morphology of the product can be tailored by varying the reaction time. A possible crystalline growth process of the NaYF₄:Yb,Er micro/nanocrystals was discussed. The obtained half opened microtubes exhibited an intense green upconversion luminescence, which may be attractive in novel optoelectronic devices.     

Submicron rectangular hollow tube crystals of rutile-type GeO2

Single crystals of rutile-type GeO₂ having a structure equivalent to that of TiO₂, a well-known photocatalyst, have been grown for the first time in supercritical oxygen at approximately 5 GPa and 3000 K. The obtained crystals exhibit a rectangular hollow tube structure with submicron size (cross section with sides of ∼500 nm, wall thickness of ∼20 nm, and longitudinal length of ∼5 μm). These single crystals were grown within 1 s and along the c-axis surrounded by the (1 1 0) faces. The crystal growth mechanism strongly depends on the growth mechanism of rutile-type oxides, and the extremely short growing time is an important factor in the formation of hollow tube crystals.     

Solvothermal synthesis of K2V3O8 nanorods

A solvothermal route has been developed to synthesize K₂V₃O₈ nanorods via the reduction of V₂O₅ using ethanol as the reducing agent as well as the solvent at 200°C. X-ray diffraction and selected area electron diffraction analysis revealed that the as-synthesized products are of tetragonal structure K₂V₃O₈. Transmission electron spectroscopy image showed that the obtained K₂V₃O₈ comprises rod-like nanocrystallites. The formation mechanism of K₂V₃O₈ was studied.     

Preparation of nanoscaled BaTiO3 powders by DSS method near room temperature under normal pressure

A new method of direct synthesis nano-BaTiO₃ powders from solution was developed in this study. Dissolving Ba(OH)₂·8H₂O into water as base solution, nanocrystalline BaTiO₃ powders can be obtained by mixing ethanol solution of tetrabutyl titanate with hot base solution under normal pressure. When the temperature of the base solution was 60°C, we obtained crystalline powders with average particle size of about 25 nm. The activity of the powders can be held up because the calcination at high temperature is not necessary using this method.     

Ca3N2 as a flux for crystallization of GaN

In this work Ca₃N₂ was investigated as a potential flux for crystallization of GaN. Melting temperature of the potential flux at high N₂ pressure evaluated by thermal analysis as 1380 °C is in good agreement with the theoretical prediction. It is shown that Ca₃N₂ present in the liquid gallium in small amount (1 at%) dramatically accelerates synthesis of GaN from its constituents. On the other hand, it does not influence significantly the rate of GaN crystallization from solution in gallium in temperature gradient for both unseeded and seeded configurations. However the habit and color of the spontaneously grown GaN crystals change drastically. For 10 mol% Ca₃N₂ content in the liquid Ga it was found that the GaN thick layer and GaN crystals (identified by micro-Raman scattering measurements) were grown on the substrate. For growth from molten Ca₃N₂ (100%) with GaN source, the most important observations were (i) GaN source material was completely dissolved in the molten Ca₃N₂ flux and (ii) after experiment, GaN crystals were found on the sapphire substrate.     

Thermogravimetric analysis and microstructural observations on the formation of GaN from the reaction between Ga2O3 and NH3

Thermogravimetric analysis (TGA) and microstructural observations were carried to investigate the nitridation mechanism of β-Ga₂O₃ powder to GaN under an NH₃/Ar atmosphere. Non-isothermal TGA showed that nitridation of β-Ga₂O₃ starts at ∼650 °C, followed by decomposition of GaN at ∼1100 °C. Isothermal TGA showed that nitridation follows linear kinetics in the temperature range 800–1000 °C. At an early stage of nitridation, small GaN particles (∼5 nm) are deposited on the β-Ga₂O₃ crystal surface and they increase with time. We proposed a mechanism for the nitridation of Ga₂O₃ by NH₃ whereby nitridation of β-Ga₂O₃ proceeds via the intermediate vapor species Ga₂O(g).     

Growth and optical properties of self-frequency-doubling laser crystal Yb:LuAl3(BO3)4

Single crystal of Yb:LuAl₃(BO₃)₄(Yb:LuAB) was grown by the flux method for the first time. The cell parameters of the grown crystal were estimated by X-ray diffraction analysis. The result indicates the symmetry of trigonal space group R32, with lattice parameters a=b=9.26372 Å, c=7.21405 Å, V=536.14 Å³, and Z=4. The absorption and emission spectra of Yb:LuAB crystal at room temperature has also been studied. The fluorescence lifetime for Yb:LuAB crystal is about 1.48 ms. The heat capacity was measured from 25 to 500 °C. Its second harmonic generation efficiency in LuAl₃(BO₃)₄ crystal is 3–4 times that of KDP crystal. These results show that Yb:LuAB crystal would be a potential self-frequency-doubling laser crystal.     

Synthesis of monodispersed cubic magnetite particles through the addition of small amount of Fe into Fe(OH)2 suspension

Magnetite particles were synthesized through a process including dissolution of Fe(OH)₂ and precipitation of an oxidized phase in aqueous solution. The Fe³⁺ ion was added at the beginning of the synthesis to accelerate the formation of magnetite, control the particle size and improve the monodispersibility. It was found that the addition of Fe³⁺ ion affected the nucleation and the formation of magnetite particles significantly. Magnetite nanoparticles with small particle size and narrow size distribution were obtained. Furthermore, high magnetic properties were obtained in small particle size. The particle size and magnetic properties increased through the increase of Fe²⁺/Fe³⁺ ratio.     

Synthesis, thermal and magnetic properties of new metal iodate: (LiFe1/3)(IO3)2

This paper reports the detail synthesis of a new kind of metal iodate, anhydrous (LiFe_1/3)(IO₃)₂, from aqueous solutions. The synthesized compound shows spinal morphology and is chemical stable up to 400°C. The iodate shows paramagnetic behavior from room temperature down to 4.2 K. At room temperature, the new compound has a hexagonal structure with the lattice parameters a=5.4632(2) Å, c=5.0895(6) Å, Z=1, space group of P6₃.     

Growth and spectral properties of Nd-doped Sr3Y(BO3)3 crystal

A new crystal of Nd³⁺:Sr₃Y(BO₃)₃ with dimension up to 25×35 mm² was grown by Czochralski method. Absorption and emission spectra of Nd³⁺: Sr₃Y(BO₃)₃ were investigated . The absorption band at 807 nm has a FWHM of 18 nm. The absorption and emission cross sections are 2.17×10⁻²⁰ cm² at 807 nm and 1.88×10⁻¹⁹ cm² at 1060 nm, respectively. The luminescence lifetime τ_f is 73 μs at room temperature     

Dynamic process of crystallization of Sb2Se3 from Sb50Se50 amorphous film

Dynamics of crystallization of amorphous antimony-selenium film deposited on carbon substrate have been studied by the high-resolution transmission electron microscopy. The amorphous film was suddenly crystallized at 200°C by heating in vacuum. By the electron beam irradiation crystallization occurred at the focused electron beam region in the amorphous film. The growth process of crystallization by electron beam irradiation was recorded on a video image at the atomic resolution mode. The growth front of crystallization showed nano-concave and -convex shapes. The recrystallization with the different orientation at the first grown crystal have been found, and discussed as the influence of remaining antimony crystallites at the first crystallized film region.     

Controlled synthesis of different morphologies of BaWO4 crystals via a surfactant-assisted method

BaWO₄ crystals with different morphologies, such as nanosheets, nanobelts, flower-like, quadrangled plates and sheaves of dendrite, have been successfully synthesized via PVP as templates. Our result shows that reaction parameters, such as the concentration of PVP aqueous solutions, pH value of the starting solution and molar ratio of [Ba²⁺]/[WO₄²⁻] played important roles in the formation of BaWO₄ crystal with different morphologies. It is obviously different between microwave irradiation heating and oil bath heating. The products were characterized by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy and electron diffraction.     

Thermal and laser properties of Yb:YAl3(BO3)4 crystal

Large optical-quality Yb:YAl₃(BO₃)₄(Yb:YAB) crystals have been grown by the flux method. The thermal properties of Yb:YAB crystal were measured for the first time. The thermal properties of Yb:YAB crystal with different Yb³⁺ ion concentrations are also reported. The results show that the ytterbium concentration influences the properties of Yb:YAB crystal. The specific heat decreases with the increase of Yb³⁺ ion concentrations in the experiment range. Apparently, the thermal expansion coefficient increases along the c-direction with the increase of Yb³⁺ ion concentrations, while it changes slightly along the a-direction. The output laser in 1120–1140 nm ranges has been demonstrated pumped by InGaAs laser. The slope efficiency is 3.8%. The self-frequency-doubling output power of 1 mW is achieved.     

Phase relations around langasite (La3Ga5SiO14) in the system La2O3–Ga2O3–SiO2 in air

Phase relations around langasite (LGS, La₃Ga₅SiO₁₄) were studied on the basis of phase assemblage observed during calcination and crystallization process of samples of various compositions in the ternary system La₂O₃–Ga₂O₃–SiO₂. A ternary compound of apatite structure, La₁₄Ga_xSi_9–xO_39–x/2 was found for the first time. Crystallization of this compound was observed in the cooling process of molten samples of stoichiometric LGS as well as LGS single crystal, demonstrating that LGS is an incongruent-melting compound. A phase diagram was established primarily based on the crystallization sequence in the cooling process.     

Anisotropic vapor phase growth of Ga2O3 crystalline nanobelts

Ga₂O₃ nanobelts were synthesized by gas reaction at high temperature in the presence of oxygen in ammonia. X-ray diffraction and chemical microanalysis revealed that the nanostructures were Ga₂O₃ with the monoclinic structure. Electron microscopy study indicated the nanobelts were single crystalline with broad (0 1 0) crystallographic planes. The nanostructures grew anisotropically with the growth direction of . Statistical analysis of the anisotropic morphology of the nanobelts and electron microscopy investigation of the nanobelt tips indicated that both vapor–solid and vapor–liquid–solid mechanisms controlled the growth process. The anisotropic nature of crystallographic morphology is explained in terms of surface energy.     

Catalytic growth of In2O3 nanobelts by vapor transport

Indium oxide (In₂O₃) nanobelts have been fabricated by thermal evaporation of metallic indium powders with the assistance of Au catalysts. The as-synthesized nanobelts are single-crystalline In₂O₃ with cubic structure, and usually tens of nanometers in thickness, tens to hundreds of nanometers in width, and several hundreds of micrometers in length. The room temperature photoluminescence spectrum of In₂O₃ nanobelts features a broad emission band at 620 nm, which could be attributed to oxygen deficiencies in the as-synthesized belts. The formation of In₂O₃ nanobelts follows a catalyst-assistant vapor—liquid–-solid growth mechanism, which enables the controlled growth of individual belts on predetermined sites.     

Dual mineralization of dicalcium phosphate and hydroxyapatite formation on both sides of porous membrane: Alternating current induces pH-modulated crystal deposition

Dual mineralization on a porous membrane was carried out using an electrochemical approach. The porous membrane was interposed between a pair of glass cells, and calcium chloride (CaCl₂) and sodium hydrogenphosphate (Na₂HPO₄) solutions were separately injected into the cells. After inserting platinum electrodes into the cells, an alternating current with a sine waveform was applied for a given period of time. The resulting membrane was removed from the glass cells and rinsed with ultrapure water. The minerals formed on the membrane were analyzed by using spectroscopic methods such as scanning electron microscopy (SEM), infrared (IR) spectroscopy, and X-ray diffraction (XRD) and identified to be dicalcium phosphate and hydroxyapatite. It was noted that dicalcium phosphate formed on one side of the membrane, while hydroxyapatite was formed on the other side. Thus, dual mineralization could be successfully achieved on both sides of the porous membrane under an alternating current. This process of dual mineralization is very useful for the formation of versatile organic–inorganic hybrids and also for the regulation of the polymorphs on either side of a membrane.     

Growth and properties of Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 single crystals directly from melt

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by a modified Bridgman method directly from melt using an allomeric Pb[(Mg_1/3Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal as a seed. X-ray diffraction (XRD) measurement confirmed that the as-grown PZNT91/9 single crystals are of pure perovskite structure. Electrical properties and thermal stabilization of PZNT91/9 crystals grown directly from melt exhibit different characters from those of PZNT91/9 crystals grown from flux, although segregation and the variation of chemical composition are not seriously confirmed by X-ray fluorescence analysis (XPS). The [0 0 1]-oriented PZNT91/9 crystals cut from the middle part of the as-grown crystal boules exhibit broad dielectric-response peaks at around 105 °C, accompanied by apparent frequency dispersion. The values of piezoelectric constant d₃₃, remnant polarization P_r, and induced strain are about 1800–2200 pC/N, 38.8 μC/cm², and 0.3%, respectively, indicating that the quality of PZNT crystals grown directly from melt can be comparable to those of PZNT91/9 single crystals grown from flux. However, further work deserves attention to improve the dielectric properties of PZNT crystals grown directly from melt. Such unusual characterizations of dielectric properties of PZNT crystals grown directly from melt are considered as correlating with defects, microinhomogeneities, and polar regions.