Effect of TiO2 addition on the crystallization and tribological properties of MgO–CaO–SiO2–P2O5–F glasses

The kinetic parameters including the activation energy for crystallization (E), the Avrami parameter (n) and frequency factor (υ) of a glass in the MgO–CaO–SiO₂–P₂O₅–F system were studied using non-isothermal differential thermal analysis (DTA) with regard to small amount of TiO₂ additions. It has been shown that the role of TiO₂ changes from a glass network former to a glass network modifier with increasing TiO₂ content in this system. The kinetic parameters of the crystallizing phases, apatite and wollastonite, indicated changes accompanied with TiO₂ additions, implying that the TiO₂ is an effective nucleating agent for promoting the crystallization of apatite and wollastonite. The most effective addition is of about 4 wt% TiO₂ in this system. The wear rate and friction coefficient decreased from 1.8 ± 0.1 to 0.9 ± 0.2 and 0.87 to 0.77, respectively, when 4 wt% TiO₂ was incorporated to the base glass.     

LiMn_2O_4/TiO_2催化剂上甲烷氧化偶联反应性能的研究

采用固相反应法制备了具有尖晶石结构的LiMn_2O_4/TiO_2系列催化剂,探讨了TiO_2、Li/TiO_2、Mn/TiO_2、LiMn_2O_4及LiMn_2O_4/TiO_2等不同组成催化剂的甲烷氧化偶联反应性能,采用XRD、XPS、CO_2-TPD和H_2-TPR等表征方法对该系列催化剂进行了分析。结果表明,具有尖晶石结构的LiMn_2O_4化合物具有较高的甲烷氧化偶联催化活性,在775℃、0.1MPa、7200mL/(h·g),CH_4∶O_2(体积比)为2.5的条件下,甲烷转化率可达25.8%,C2选择性可达43.2%。TiO_2的存在不仅进一步提高了甲烷转化率和C2选择性,还有效抑制了甲烷完全氧化形成CO_2的过程。负载8%LiMn_2O_4的LiMn_2O_4/TiO_2催化剂性能达到最优,此时甲烷转化率达到31.6%,C2选择性为52.4%,CO_2选择性降低到26.3%。考察了不同焙烧温度对催化剂活性的影响,850℃为LiMn_2O_4/TiO_2催化剂的最佳焙烧温度。     

TiO_2载体掺杂对Mn-Ce/TiO_2催化剂低温脱硝性能影响研究

以TiO_2、TiO_2-Al_2O_3及TiO_2-SiO_2为载体,选取Mn为活性组分,Ce为活性助剂,采用分布共混法制备低温SCR催化剂,分析了TiO_2载体掺杂Al_2O_3、SiO_2改性后对Mn-Ce/TiO_2催化剂低温脱硝活性的影响,运用BET、SEM、XRD、H2-TPR以及NH_3-TPD等测试手段对催化剂进行了表征。结果表明,TiO_2载体经掺杂改性后,Mn-Ce/TiO_2催化剂的比表面积、孔结构参数以及表面孔结构形貌均得到改善和提高;Mn-Ce/TiO_2-Al_2O_3和Mn-Ce/TiO_2-SiO_2催化剂中TiO_2的结晶度均有不同程度降低;经TiO_2载体掺杂改性后的催化剂表面低温还原峰面积及催化剂表面酸性位种类及酸性大小显著改善,这都有助于提高催化剂的脱硝活性。通过对TiO_2载体掺杂SiO_2和Al_2O_3改性后,催化剂的脱硝活性明显提高,反应温度在80-140℃时,催化剂SCR脱硝活性的顺序是:Mn-Ce/TiO_2-SiO_2M n-Ce/TiO_2-Al_2O_3M n-Ce/TiO_2。     

γ-Al2O3对SCR脱硝催化剂V2O5-WO3/TiO2的改性研究

采用溶胶凝胶法制备了不同γ-Al₂O₃含量的钛铝复合载体,以此为载体采用浸渍法负载V₂O₅和WO₃制备了一系列催化剂。采用X射线衍射(XRD)、比表面积测定(BET)、程序升温还原(H₂-TPR)、高分辨率透射电子显微镜(HRTEM)等表征技术对催化剂表面形态进行分析,同时在模拟氨气选择性催化还原NO(NH₃-SCR)的反应条件下,对催化剂的脱硝反应活性和SO₂抗中毒进行考察。结果发现,TiO₂和γ-Al₂O₃之间的协同作用使得V₂O₅-WO₃/TiO₂-γ-Al₂O₃催化剂的脱硝效率及活性窗口明显优于单一载体制备的催化剂,表现出了良好的热稳定性和抗SO₂毒化能力,特别是V₂O₅-WO₃/TiO₂-15% γ-Al₂O₃在310~460 ℃,NO的转化率均在80%以上,反应窗口最宽。各种表征结果表明,TiO₂-γ-Al₂O₃复合载体中γ-Al₂O₃高度分散在TiO₂上,复合载体具有较大的比表面积,同时具有较强的还原能力。     

Properties of chemical vapour deposited nanocrystalline TiO2 thin films and their use in dye-sensitized solar cells

Nanocrystalline titanium dioxide (TiO₂) thin films have been prepared using titanium(IV) isopropoxide as a precursor onto the glass and fluorine doped tin oxide coated glass substrates by chemical vapour deposition technique at 400 °C substrate temperature. X-ray diffraction study confirms the polycrystalline nature of TiO₂ with anatase phase having tetragonal crystal structure. The films are 975 nm thick and transparent having transmittance grater than 80%. Atomic force microscopy (AFM) images reveal the nanocrystalline morphology with grain size of 200 nm. The film shows a sharp absorption edge near 350 nm. Photoelectrochemical study shows that TiO₂ thin film sensitized with Brown Orange dye is found to exhibit relatively maximum I_sc and V_oc among the studied dyes. The values of fill factor (FF) and efficiency (η) for the dye-sensitized solar cell (Brown Orange dye-sensitized TiO₂) are 0.54 and 0.17%, respectively. Such films would serve as better prospects for dye-sensitized solar cells.     

焙烧温度对TiO2-ZrO2复合氧化物性质及其对十八醇脱水制十八烯反应性能的影响

通过在ZrO_2中掺杂TiO_2,并在350-500℃下焙烧,制备了系列TiO_2-ZrO_2复合氧化物催化剂,将其应用于十八醇脱水制十八烯反应。随焙烧温度的升高,催化剂表面的Lewis酸性位量逐渐增加,450℃焙烧的催化剂Lewis酸性位量最多,焙烧温度继续升高则Lewis酸性位量降低;催化剂中未发现Br?nsted酸性位。焙烧温度≤400℃的TiO_2-ZrO_2复合氧化物形成Ti-O-Zr键,呈无定形态;焙烧温度400℃的TiO_2-ZrO_2复合氧化物呈单斜相和四方相ZrO_2晶型。晶相结构和酸性位量综合影响催化剂的十八醇脱水性能,具有单斜相和四方相ZrO_2晶型的催化剂上酸性位活性很低,具有无定形相的催化剂上酸性位活性显著增加,400℃焙烧的催化剂1-十八烯收率最高。     

Synthesis and study of Bi2Ti2O7/TiO2 composites as efficient visible-light-active photocatalysts in the reduction of aqueous Cr(VI)

In this work, Bi_2Ti_2O_7/TiO_2 composites were synthesized and studied as potential visible-light-activated photocatalysts in the reduction of aqueous Cr(VI). Bi_2Ti_2O_7/TiO_2 composites with tunable compositions were synthesized via a solvothermal-calcination two-step method, simply by changing the molar ratios of Bi(NO_3)_3·5H_2O to tetrabutyl titanate in the reactants. The compositions, structures and optical properties of the as-synthesized Bi_2Ti_2O_7/TiO_2 composites were characterized by X-ray diffraction, field emission scanning electron microscopy and UV–vis diffuse reflectance spectra. The photocatalytic activity of the as-synthesized Bi_2Ti_2O_7/TiO_2 composites was tested in the reduction of aqueous Cr(VI)under visible-light(λ420 nm) irradiation, and compared with that of TiO_2 nanoparticles. It was observed that the as-synthesized Bi_2Ti_2O_7/TiO_2 composites exhibited much higher photocatalytic activity than TiO_2 nanoparticles, and the most efficient composite(300 mg) can achieve the complete reduction of Cr(VI) in 300 mL of 50 mg/L K_2Cr_2O_7 aqueous solution under visible-light(λ420 nm)irradiation in 90 min.     

Thermal behavior of nitrided TiO2/In2O3 by TG–DSC–MS combined with PulseTA

TiO₂/InN (In/(Ti + In) = 6.5:100 mol) was prepared by nitridation of TiO₂/In₂O₃ by NH₃ at 580 °C for 8 h. Only the anatase TiO₂ phase was detected in the XRD measurements. The highly dispersed InN clusters on the surface of anatase TiO₂ nanocrystals were beyond the detection limit of XRD. In order to confirm the existence of InN in the products of nitridation, thermogravimetry–differential scanning calorimetry–mass spectrometry (TG–DSC–MS) coupling techniques were used for a simultaneous characterizing study of the changes of mass, enthalpy and determination of the evolved gases during the thermal decomposition of the InN and the nitrided TiO₂/In₂O₃ samples. Moreover, pulse thermal analysis (PulseTA) was combined with TG–DSC–MS for the quantitative calibration of the evolved nitrogen formed during the thermal decomposition of the InN and the nitrided TiO₂/In₂O₃. The applied technique enabled identification and quantification of the InN in the products of the nitridation of TiO₂/In₂O_3.     

Relationships between oxygen diffusion characteristics of polycrystalline and single crystal 2MgO · TiO2

Self-diffusion coefficients of oxygen in both polycrystalline and single crystal 2MgO·TiO₂ have been measured at an ambient oxygen pressure of about 40 mm Hg over the temperature range 1080–1450°C. A convenient method to estimate the volume diffusion coefficient, D₁, of this polycrystal in which the relative magnitude in D_g (grain boundary diffusion coefficient) with respect to D₁ falls between two extremes, i.e., D_g = D₁ and D_g D₁, is newly proposed, and its plausibility is examined by comparing the resultant D₁ with that of single crystal 2MgO·TiO₂. Not only the magnitude but also the temperature dependence of the “apparent” diffusivity of these polycrystalline particles considerably varied with their particle size. The reason for this semiquantitatively interpreted in terms of the relative magnitude of D_g with respect to D₁.     

一维TiO2锐钛矿/金红石异相结的制备及光催化降解甲醛性能

TiO₂异相结主要通过高温方法制备,所制备材料的形貌和组成较难控制,尤其是在较低温度下一步制备一维TiO₂异相结仍具有一定的挑战性。采用简单、方便的一步水热法,在较低温度下(180℃)制备了一维纳米TiO₂异相结材料。X射线衍射(XRD)和高分辨透射电镜(HRTEM)分析表明,制备的材料以一维金红石相TiO₂纳米棒(长度：(400±50) nm,直径：(60±5) nm)为基本结构,粒径分布均匀的锐钛矿相TiO₂纳米粒子(直径：(9.5±0.5) nm)高密度、单分散地负载在纳米棒上。通过控制水热反应时间成功调控了异相结中锐钛矿相TiO₂的含量(20%～50%),进而实现了其光催化降解HCHO性能的调控。实验结果表明,当锐钛矿相TiO₂的含量为33%时(TiO₂-24,水热时间24 h制备的样品),异相结光催化剂表现出最佳的HCHO降解性能：在低光强LED灯(波长为365 nm,光强为12.26 mW·cm     

添加Cl离子对V_2O_5-WO_3/TiO_2催化剂低温NO转化率的影响

考察添加不同含量Cl离子对浸渍法制备的Cl-V_2O_5-WO_3/TiO_2催化剂低温NO转化率的影响。随着Cl离子质量添加量从0增加到2.5%,Cl-V_2O_5-WO_3/TiO_2催化剂NO转化率先升高后降低,结合在含有SO_2和H2O的SCR实验结果,确定1.5%Cl-V_2O_5-WO_3/TiO_2为性能最优催化剂。在反应温度为149-362℃,NO转化率大于95%;在145-385℃,NO转化率大于90%。采用XRF、BET、XRD、TG、FT-IR和H2-TPR等方法表征了催化剂的物理化学性能和结构。结果表明,在反应气氛中加入SO_2和H2O后,催化剂比表面积和孔容均减小,副反应产物含有NH+4和SO_2-4。适量Cl离子可以抑制硫物种沉积,减少副反应产物生成,增强催化剂抗中毒能力。     

非晶态MnO_x/TiO_2催化剂的制备及其低温NH_3-SCR性能

采用自发沉积法、共沉淀法及浸渍法制备MnO_x/TiO_2催化剂,通过XRD、TEM、N2吸附-脱附、XPS、H_2-TPR、NH_3-TPD等一系列表征手段研究MnO_x/TiO_2催化剂的结构与性质,并考察MnO_x/TiO_2催化剂低温NH_3-SCR性能。结果表明,自发沉积法制备的MnO_x/Ti O2(s)催化剂具有完全非晶态结构,Mn和Ti之间存在强相互作用,较共沉淀法制备的MnO_x/TiO_2(c)及浸渍法制备的MnO_x/Ti O2(i)表现出更强的氧化还原能力。MnO_x/TiO_2(s)具有较高的比表面积、较多的表面酸量,有利于NH_3的吸附与活化。且表面高浓度的Mn4+离子及吸附氧,有利于将NO氧化为NO2,促进发生"fast-SCR"反应,进而使其表现出优异的低温脱硝性能。MnO_x/TiO_2(s)催化剂在150℃时NO的转化率高达92.8%,在150-350℃NO的转化率保持在90%以上,此外其还具备较强的抗H_2O和SO_2毒化能力。     

TiO_2-Al_2O_3复合载体的制备及Co-Mo/TiO_2-Al_2O_3催化剂加氢脱硫性能的研究

通过改进的溶胶-凝胶法(SG)、共沉淀法(CP)、表面沉淀法(PR)及混捏法(ME)制备TiO_2-Al_2O_3复合载体,考察了不同制备方法对复合载体物理性质的影响。采用浸渍法制备Co-Mo/TiO_2-Al_2O_3-X加氢脱硫催化剂,研究了Co-Mo/TiO_2-Al_2O_3-X加氢脱硫催化剂的脱硫性能。利用XRD、BET、SEM等表征手段对复合载体及催化剂进行表征分析。结果表明,SG法制备的复合载体粒径均一,具有较大的比表面积、孔径和孔体积;CP法制备复合载体时TiO_2以单层或亚单层的分散状态高度分散于γ-Al_2O_3中。在氢气压力3.0 MPa、反应温度280℃、反应时间4 h、液时空速1.4 h-1和氢油比600的条件下,SG法制备的Co-Mo/TiO_2-Al_2O_3催化剂具有较高加氢脱硫活性,噻吩转化率达到96.6%。     

Decomposition of toluene using an atmospheric pressure plasma/TiO2 catalytic system

Application of atmospheric pressure plasma as an alternative technology for the destruction of toluene is demonstrated in this study. Used TiO₂ colloidal solution was obtained by an improved sol–gel method, and coated on glass beads to prepare decomposition of toluene. The physical property of synthesized TiO₂ catalyst film was analyzed by XRD and SEM spectroscopy. From these results, it was identified that the catalyst film exhibited anatase structure with particle size of about 50–100 nm after calcination at 500 °C for 1 h. The decomposition of toluene in TiO₂/O₂ plasma system was investigated. Amounts of the catalyst and toluene concentration were fixed as 3 wt.% and 1000 ppm, respectively. The analyses for performance of toluene decomposition and intermediates in reaction were done by the in situ method using the mass spectroscopy and gas chromatography. The toluene of 40% was decomposed at pulse voltage of 13 kV in the only O₂ plasma condition without TiO₂ catalyst. Furthermore, the conversion enhanced remarkably in the TiO₂/O₂ plasma system, and it reached 70% at pulse voltage of 13 kV after 120 min. This result was very notable compared with that in photocatalytic system, with below 40% after 120 min reaction.     

TiO_2掺杂CuMnCe/Al_2O_3催化剂对甲烷催化燃烧脱氧反应的影响

以掺杂了不同TiO_2含量的Al_2O_3作为载体,通过等体积浸渍法制备了一系列不同TiO_2含量的CuMnCe/TiO_2-Al_2O_3催化剂,用BET、H_2-TPR、XRD和XPS表征技术对催化剂物理化学性质进行表征,并考察了催化剂在含甲烷气脱氧反应中的催化性能。结果表明,在载体中添加TiO_2对催化剂活性组分的晶相结构和分散度没有明显影响;但有效改善了Al_2O_3载体抗烧结能力;增加了CuMnCe/Al_2O_3催化剂表面Ce~(3+)/(Ce~(3+)+Ce~(4+))的相对含量,从而提高了活性氧的移动性,且使催化剂表面可氧化还原物种含量和表面吸附氧Osur/(Osur+Olatt)的含量增多。有效改善了催化剂在含甲烷气催化燃烧脱氧上的催化活性。其中,CuMnCe/4%TiO_2-Al_2O_3表现出最优的催化活性,在387℃时可使含甲烷气中氧气的转化率达到100%。     

前驱体溶液pH值对V2O5-WO3/TiO2催化剂的低温NH3-SCR性能的影响

采用调节前驱体溶液pH值的方法制备了用于低温NH₃-SCR的V₂O₅-WO₃/TiO₂催化剂。通过XPS、Raman光谱、H₂-TPR、NH₃-TPD、NH₃-DRIFT、XRD及物理吸附等手段对催化剂进行了表征分析,并对其脱硝催化活性进行了测试。结果表明,前驱体溶液酸性的增强能够提高催化剂表面聚合态钒物种和V⁴⁺⁽³⁺⁾/V⁵⁺的比值以及表面酸性,增加活性位数量、降低反应的活化能、提高其脱硝催化性能。因此,通过提高前驱体溶液的酸性,有助于制备出脱硝活性较好的NH₃-SCR催化剂。     

MoS_2负载量对MoS_2/TiO_2光催化降解苯酚效率的影响及其作用机理研究

通过水解法制备TiO_2纳米颗粒,与经过超声处理后的MoS_2片层纳米材料复合制备MoS_2/TiO_2纳米催化剂,考察不同MoS_2负载量对其光催化降解苯酚效率及路径的影响。XRD、SEM、EDS、FT-IR和UV-vis DRS等表征结果表明,复合催化剂主要由锐钛矿型TiO_2和MoS_2组成;剥离后的MoS_2呈现薄片层状结构,均匀地分散在TiO_2纳米颗粒当中。光催化降解苯酚性能测试结果显示,对于MoS_2/TiO_2催化剂,MoS_2负载量的提高有利于光催化降解苯酚效率的提高;当MoS_2负载量为27%时,复合M o S2/TiO_2纳米颗粒的光催化性能最佳,反应80 min后可将苯酚完全降解。通过对苯酚降解过程中生成中间产物跟踪发现,MoS_2负载量的提高有利于促进中间产物苯醌、对苯二酚以及邻苯二酚的生成,进而提升了MoS_2/TiO_2复合材料的光催化性能。     

Devitrification behaviour of glasses near the Na2O·2 SiO2 composition

The influence of small substitutions of different cations for Na⁺ ions on the devitrification behaviour of Na₂O·2 SiO₂ glass has been investigated by differential thermal analysis.

The stability of the glasses has been related to the glass transition temperature/liquidus temperature ratio and to the field strength of the cations.     

The effect of changing the TiO2 content (0-6%) on the structure and thermal evolution of glasses obtained from porphyric sands and dolomite

Glasses have been obtained from mixtures of porphyric sands and dolomite. The influence of changes in the TiO₂ content (0-6%) on the glass structure and the formation of crystalline phases on reheating has been studied. The experimental results suggest that in the studied system TiO₂ promotes glass-in-glass phase separation and plays the role of a nucleating agent. The activation energy for crystal growth, E_C = 486 kJ mol⁻¹, and the Avrami parameter (m = 1) have been evaluated by means of thermoanalytical techniques in the case of the base glass (no TiO₂ added). The value of the Avrami parameter (m = 1) agrees well with SEM observations of dendritic crystal growth from surface nuclei. In the other glasses, lath-like crystals were observed, the microstructure being finer the greater the TiO₂%. The first addition of TiO₂ (2%) gives, on quenching, a partially devitrified product; subsequent additions of titania, surprisingly, allow glasses to be formed more easily. The experimental results suggest that Na₂O and K₂O, present in the porphyric sands and therefore in the glasses (to a total amount of ≈ 5.6%), segregate preferentially into the titania-rich phase with respect to MgO. Taking into account that Na₂O and K₂ are useful in lowering the liquidus temperature of glasses but are known to have a negative effect on the mechanical properties, this can be important in the production of glass ceramics.     

锂盐及制备工艺对固态电解质Li7La3Zr2O12成相的影响研究

石榴石型Li₇La₃Zr₂O₁₂(LLZO)离子导电性高,在全固态锂离子电池中具有潜在的应用价值。但目前报道的LLZO制备工艺烧结温度范围宽,稳定性差,不利于宏量制备。本文以烧结产物物相结构和结晶度为考察指标,系统研究了锂源及用量、烧结温度、烧结时间等因素对LLZO成相的影响。结果表明,当以分解温度较低的锂盐(LiNO₃)为原料时,在800℃下得到四方相LLZO,900℃时呈立方相LLZO;当以分解温度较高的锂盐(Li₂CO₃)为原料时,900℃才能形成四方相LLZO。烧结时间的延长和温度升高均会导致锂的挥发损失,影响LLZO物相的形成。通过增加锂盐用量、改变烧结前驱体聚集特性与烧结时间可抑制锂的挥发。当以过量10%的Li₂CO₃为原料时,900℃烧结6h可稳定的得到立方相LLZO。该研究较为系统地分析了制备工艺对LLZO成相的影响,可为LLZO宏量稳定制备提供借鉴。