A FIA-system for As(III)/As(V)-determination with electrochemical hydride generation and AAS-detection

A flow-injection system with electrochemical hydride generation and atomic absorption detection for As(III)/As(V) determination is described. A simple electrolytic flow-through cell has been developed and optimized. Several cathode materials like Pt, Ag, Cu, C and Pb have been tested. The influence of the electrolysis current, concentration of sulfuric acid, carrier stream, flow rate, sample volume and interferences by other metals on the arsenichydride generation have been studied. For the determination of total inorganic arsenic, As(V) is reduced to As(III) on-line by postassium iodide or L-cysteine at 95° C. The influence of the temperature and the reduction medium on this pre-reduction step has been tested. The calibration curve is linear in the range of 5 to 50 g/L for As(III) and total inorganic arsenic and shows a higher sensitivity than in case of reduction with sodium tetrahydroborate. The detection limit is 0.4 g/L for As(III) and 0.5 g/L for total inorganic arsenic at a sample volume of 1 mL.     

Evaluation of electrochemical hydride generation for spectrophotometric determination of As(III) by silver diethyldithiocarbamate

A batch electrochemical hydride generation system was developed for the spectrophotometric determination of inorganic As(III) by silver diethyldithiocarbamate. This method is based on electrochemical reduction of As to Arsine (AsH₃) in acidic media and on the subsequent reaction of AsH₃ with silver diethyldithiocarbamate to give an absorbing complex at 525 nm. The electrochemical generator consisted of a cathode cell separated from the anode cell by a porous glass frit and was operated with a constant direct current. A pre-activated graphite rod was used as cathode material for the production of AsH₃. The parameters related to the electrochemical hydride generation were investigated. Under optimized conditions, only As(III) can be converted to AsH₃ and a pre-reducing stage is required for total inorganic As analysis. The characteristic data of the electrochemical hydride generation and common hydride generation by NaBH₄ were compared. Also, the effects of interferences and their elimination were investigated. An absolute detection limit of 0.5 μg (3s_b) and a concentration detection limit of 0.05 μg/ml were obtained using a 10 ml sample volume. The relative standard deviation for five replicate analysis of 30 μg As(III) was 1.2%. The accuracy and recovery of the method were demonstrated by analysing spiked artificial sea water and tap water.     

Arsenic speciation in aqueous samples using a selective As(III)/As(V) preconcentration in combination with an automatable cryotrapping hydride generation procedure for monomethylarsonic acid and dimethylarsinic acid

Differentiation between As(III) and As(V) is accomplished using earlier developed selective preconcentration methods (carbamate and molybdate mediated (co)precipitation of As(III) and As(V) respectively) follewed by AAS detection of the (co)precipitates. Apart from this, separation of methylated arsenic species is performed by an automatable system comprising a continuous flow hydride generation unit in which monomethylarsonic acid (MMAA) and dimethylarsinic acid (DMAA) are converted into their corresponding volatile methylarsines, monomethylarsine (MMA) and dimethylarsine (DMA) respectively. These species are cryogenically trapped in a Teflon-line stainless stell U-tube packed with a gas chromatographic solid-phase and subsequently separated by selective volatilization. A novel gas drying technique by means of a Perma Pure dryer was applied successfully prior to trapping. Detection is by atomic absorption spectrometry (AAS). MMAA and DMAA are determined with absolute limits of detection of 0.2 and 0.5 ng, respectively. Investigation of the behaviour of the methylarsines in the system was conducted with synthesized⁷³As labeled methylated arsenic species. It was found that MMA is taken through the system quantitatively whereas DMA is recovered for about 85%. The opumized system combined with selective As(III)/As(V) preconcentration has been tested out for arsenic speciation of sediment interstitial water from the Chemiehaven at Rotterdam. The obtained concentrations are 28.5, 26.8 and 0.60 ng·ml^–1 for As(III), As(V) and MMAA, respectively, whereas the DMAA concentration was below 0.16 ng·ml^–1.     

Determination of As(III) and As(V) in soils using sequential extraction combined with flow injection hydride generation atomic fluorescence detection

An analytical procedure for determination of As(III) and As(V) in soils using sequential extraction combined with flow injection (FI) hydride generation atomic fluorescence spectrometry (HG-AFS) was presented. The soils were sequentially extracted by water, 0.6 mol l⁻¹ KH₂PO₄ solution, 1% (v/v) HCl solution and 1% (w/v) NaOH solution. The arsenite (As(III)) in extract was analyzed by HG-AFS in the medium of 0.1 mol l⁻¹ citric acid solution, then the total arsenic in extract was determined by HG-AFS using on-line reduction of arsenate with l-cysteine. The concentration of arsenate (As(V)) was calculated by the difference. The optimum conditions of extraction and determination were studied in detail. The detection limit (3σ) for As(III) and As(V) were 0.11 and 0.07 μg l⁻¹, respectively. The relative standard deviation (R.S.D.) was 1.43% (n=11) at the 10 μg l⁻¹ As level. The method was applied in the determination of As(III) and As(V) of real soils and the recoveries of As(III) and As(V) were in the range of 89.3-118 and 80.4-111%, respectively.     

Determination of inorganic arsenic species As(III) and As(V) by high performance liquid chromatography with hydride generation atomic absorption spectrometry detection

The paper presents the principles and advantages of a technique combining high performance liquid chromatography and hydride generation atomic absorption spectrometry (HPLC-HGAAS) applied to speciation analysis of inorganic species of arsenic As(III) and As(V) in ground water samples. With separation of the arsenic species on an ion-exchange column in the chromatographic system and their detection by the hydride generation atomic absorption spectrometry, the separation of the analytical signals of the arsenic species was excellent at the limits of determination of 1.5 ng/ml As(III) and 2.2 ng/ml As(V) and RSD of 4.3% and 7.8% for the concentration of 25 ng/ml. The hyphenated technique has been applied for determination of arsenic in polluted ground water in the course of the study on migration of micropollutants. For total arsenic concentration two independent methods: HGICP-OES and HGAAS were used for comparison of results of real samples analysis.     

Determination of As(III) and As(V) in water samples by flow injection online sorption preconcentration coupled to hydride generation atomic fluorescence spectrometry

A method was developed for the determination of arsenite [As(III)] and arsenate [As(V)] in water samples using flow injection online sorption coupled with hydride generation atomic fluorescence spectrometry (HG-AFS) using a cigarette filter as the sorbent. Selective determination of As(III) was achieved through online formation and retention of the pyrrolidine dithiocarbamate arsenic complex on the cigarette filter, but As(V) which did not form complexes was discarded. After reducing As(V) to As(III) using L-cysteine, total arsenic was determined by HG-AFS. The concentration of As(V) was calculated by the difference between As(III) and total arsenic. The analytes were eluted from the sorbent using 1.68 mol L^?1 HCl. With consumption of 22 mL of the sample solution, the enrichment factor of As(III) was 25.6. The detection limits (3σ/k) and the relative standard deviation for 11 replicate determinations of 1.0 ng mL^?1 As(III) were found to be 7.4 pg mL^?1 and 2.6%, respectively.     

Potentiometric determination of the standard potential of the As(V)/As(III) couple

The potential of the As(V)/As(III) half-cell was measured at 25 degrees with a glass electrode as reference electrode in order to eliminate the liquid-junction potential. Rapid and reproducible values could be obtained only in the presence of iodide, which increases the rate of electron-exchange between the two oxidation states of arsenic, but only at hydrogen-ion concentrations higher than about 0.5M. Extrapolation to zero ionic strength was therefore required to obtain the standard potential. A value of 573 +/- 2 mV was calculated for the half-reaction AsO(OH)(3) + 2e(-) + 2H(+) right harpoon over left harpoon As(OH)(3) + H(2)O.     

Emulsion liquid membrane separation of As(III) and As(V)

Emulsion liquid membranes (ELM) consisting of L113A (surfactant), liquid paraffin (stabilizer) and kerosene (solvent), with HCl solution acting as the external phase and KOH solution acting as the internal phase, were applied to the prior separation of arsenic(III) and arsenic(V) with subsequent spectrophotometric determination by AgDDTC. The effect of various parameters on the recovery of arsenic(III) were investigated. 8 mol/L HCl was required for 95% As(III) recovery. After reduction of As(V) to As(III) with sufficient KI, total arsenic could be determined. The RSD of As(III) and As(total) were both less than 3%. The procedure was applied to aqueous samples with a recovery of 93.5%–101%. Received: 22 March 1998 / Revised: 12 September 1998 / Accepted: 17 September 1998     

Emulsion liquid membrane separation of As(III) and As(V)

Emulsion liquid membranes (ELM) consisting of L113A (surfactant), liquid paraffin (stabilizer) and kerosene (solvent), with HCl solution acting as the external phase and KOH solution acting as the internal phase, were applied to the prior separation of arsenic(III) and arsenic(V) with subsequent spectrophotometric determination by AgDDTC. The effect of various parameters on the recovery of arsenic(III) were investigated. 8 mol/L HCl was required for 95% As(III) recovery. After reduction of As(V) to As(III) with sufficient KI, total arsenic could be determined. The RSD of As(III) and As(total) were both less than 3%. The procedure was applied to aqueous samples with a recovery of 93.5%–101%. Received: 22 March 1998 / Revised: 12 September 1998 / Accepted: 17 September 1998     

The successive polarographic determination of As(III) and As(V)

A method has been described for the successive polarographic determination of As(III) and As(V)in a sulphuric acid solution.A directly recorded polarogram shows a limiting current corresponding to the As(III) concentration, another polarogram, recorded with a second sample after reduction of As(V) to As(III) by hydrazine sulphate, gives a limiting current corresponding to the concentration As(II) + As(V).     

Determination of As(III) and total inorganic arsenic by flow injection hydride generation atomic absorption spectrometry

A simple procedure was developed for the direct determination of As(III) and As(V) in water samples by flow injection hydride generation atomic absorption spectrometry (FI–HG–AAS), without pre-reduction of As(V). The flow injection system was operated in the merging zones configuration, where sample and NaBH₄ are simultaneously injected into two carrier streams, HCl and H₂O, respectively. Sample and reagent injected volumes were of 250 μl and flow rate of 3.6 ml min⁻¹ for hydrochloric acid and de-ionised water. The NaBH₄ concentration was maintained at 0.1% (w/v), it would be possible to perform arsine selective generation from As(III) and on-line arsine generation with 3.0% (w/v) NaBH₄ to obtain total arsenic concentration. As(V) was calculated as the difference between total As and As(III). Both procedures were tolerant to potential interference. So, interference such as Fe(III), Cu(II), Ni(II), Sb(III), Sn(II) and Se(IV) could, at an As(III) level of 0.1 mg l⁻¹, be tolerated at a weight excess of 5000, 5000, 500, 100, 10 and 5 times, respectively. With the proposed procedure, detection limits of 0.3 ng ml⁻¹ for As(III) and 0.5 ng ml⁻¹ for As(V) were achieved. The relative standard deviations were of 2.3% for 0.1 mg l⁻¹ As(III) and 2.0% for 0.1 mg l⁻¹ As(V). A sampling rate of about 120 determinations per hour was achieved, requiring 30 ml of NaBH₄ and waste generation in order of 450 ml. The method was shown to be satisfactory for determination of traces arsenic in water samples. The assay of a certified drinking water sample was 81.7±1.7 μg l⁻¹ (certified value 80.0±0.5 μg l⁻¹).     

Preservation of As(III) and As(V) in some water samples

This paper reports on the behavior of arsenite [As(III)] and arsenate [As(V)] in some water samples at storage under several conditions (pH=2/natural pH, 4°C/20°C). The investigation was carried out using⁷³As as a radiotracer for both forms and with the aid of earlier developed simple speciation methods for differentiation between arsenite and arsenate. Although arsenate is the thermodynamically stable arsenic form, it was observed that arsenate in deionized water is completely converted to the trivalent state; this phenomenon took place in about one week. By monitoring the radioactive As(III) and As(V) over a period of one month in two natural water samples, a fresh water and a sea water sample, it could be concluded that no adsorption occurs on the surface of polyethylene containers, independent of storage conditions. During that period, storage at natural pH values results for both water samples in a gradual oxidation of As(III); the oxidation rate is higher for storage at 20°C. At pH=2 As(III) is fairly stable in fresh water at both storage temperatures. However, in sea water a fast oxidation of As(III) is observed (complete oxidation within 3 d at both temperatures). As(V) is stable at all storage conditions studied.     

Determination of As(III) and As(V) ions by chemiluminescence method

A new chemiluminescence (CL) method for the selective determination of As(III) and As(V) ions in aqueous solution has been studied using a FIA system. The method is based on the increased CL intensity with the addition of As(V) ion into a solution of lucigenin and hydrogen peroxide. The addition of As(III) ion into the solution did not change the CL intensity. Total concentration of As ions was determined after pre-oxidation of As(III) to As(V) with hydrogen peroxide in basic solution. The As(III) content was estimated by subtracting the content of As(V) ion from total As concentration. The effects of concentrations of KOH and H₂O₂, and flow rates of reagents on CL intensity have been investigated. The calibration curve for As(V) ion was linear over the range from 1.0×10^-2 to 10 μg/g, the coefficient of correlation was 0.997 and the detection limit was 5.0×10^-3 μg/g under the optimal experimental conditions.     

Determination of As(III) and total inorganic arsenic by on-line pretreatment in hydride generation atomic absorption spectrometry

Summary A method for the on-line prereduction of As(V) was developed in order to determine As(III) and As(V) with the same sensitivity by continuous flow hydride generation. In this procedure, the sample is continuously mixed with concentrated hydrochloric acid and a potassium iodideascorbic acid solution, flows through a heated PTFE-tube and is determined by hydride generation atomic absorption spectrometry in a heated quartz cell. The selective analysis of As(III) is carried out by continuous mixing of the sample with acetic acid and hydride generation. The method allows the rapid determination of inorganic arsenic species at concentrations down to 1 g/l. A manual sample preparation is not required.     

Oxidant-sorbent system for potable water purification to remove As(III) and As(V) oxyanions

Sorption system based on a hydride material produced by impregnation of a fibrous polyacrylonitrile anion-exchanger with potassium permanganate was studied. Tests on purification of potable water to remove tri- and pentavalent arsenic compounds were performed and demonstrated a degree of purification to below the maximum permissible concentrations established by regulations of the World Health Organization.     

Removal of aqueous As(III) and As(V) by hydrous titanium dioxide

Dissolved arsenic in drinking water is a global concern as it causes serious health problems. The purpose of this research was to study the applicability of an industrial intermediate product, a mixture of titanium hydroxide and titanium dioxide for removing aqueous arsenic. The material is common, inexpensive, and non-toxic, making it an attractive choice for drinking water purification. The kinetics and equilibrium of removing both primary inorganic arsenic forms, As(III) and As(V), were studied by separate batch experiments. The tested material functioned well in removing both of these arsenic forms. The apparent values for Langmuir monolayer sorption capacities were 31.8 mg/g for As(III) and 33.4 mg/g for As(V) at pH 4. The studied TiO(2) performed the best in acidic conditions, but also reasonably well in other pH conditions.     

Photometric measurement of trace As(III) and As(V) in drinking water

A simple, fast and sensitive light-emitting diode (LED)-based photometric method for the differential determination of ppb-ppm levels of As(III) and As(V) in potable water in the presence of ppm levels of phosphate was developed. The detection chemistry is based on the well-known formation of arsenomolybdate, followed by reduction to heteropoly blue. The front-end of the measurement system is configured to selectively retain P(V) and As(V), based on the considerable difference of the pK(a) of the corresponding acids relative to As(III). Thus, it is As(III) that is injected into the medium, oxidized in-line with KBrO(3) to As(V) and forms Mo-blue that is detected by an LED-based detector. Only As(III) is measured if the sample is injected as such; if all As in the sample is prereduced to As(III) (by the addition of cysteine, in a provided in-line arrangement), the system measures As(V)+As(III). In the present form, limit of detection (LOD) (S/N=3) is less than 8 mug l(-1) As, and the linear range extends to 2.4 mg l(-1). Potential interference from dissolved silica and Fe(III) is eliminated by the addition of NaF to the sample.     

Removal of As(III) and As(V) by natural and synthetic metal oxides

The removal properties of As(III) and As(V) by the several metal oxides having different mineral type and content of metals were investigated in batch and column reactors. The used metal oxides were Fe-oxide loaded sand (ILS), Mn-oxide loaded sand (MLS), activated alumina (AA), sericite (SC) and iron sand (IS). From the pH-edge adsorption experiments with AA and ILS, maximum As(III) adsorption was observed around neutral pH while As(V) adsorption was followed an anionic-type behavior. Among five metal oxides, AA showed the greatest removal capacity for both As(III) and As(V) through adsoption process but it has little oxidation capacity for As(III). Eventhough IS had much greater content of Fe-oxides than ILS, it showed a relatively lower removal capacity for both As(III) and As(V). This result suggests that adsorption of arsenic onto metal oxides is controlled by not only the contents of Fe-oxides but also mineral type of Fe-oxides. Column tests were performed at different combinations of metal oxides in a column reactor to find the best column system, which effectively treat both As(III) and As(V) at the same time. Among several combinations, the column reactors packed with MLS-AA and MLS-ILS showed a near complete oxidation of As(III) by MLS for a long time and the greatest adsorption of total arsenic compared to the column reactor packed with MLS-IS.     

Mechanistic aspects of electrochemical hydride generation for cadmium

A reversed-phase chromatographic method has been developed and optimised in order to detect and quantitate soybean proteins in commercial heat-processed meat products. The optimised conditions consisted of a linear binary gradient tetrahydrofurane-water-0.05% trifluoroacetic acid at a flow rate of 1 mL/min. Meat products were defatted with acetone and soybean proteins were extracted with a buffered solution at pH 9.60. The injection of this extract into the chromatographic system enabled the detection of soybean proteins in heat-processed meat products in about 12 min. The method enabled the detection and quantitation of additions of 0.38% (w/w) and 0.63% (w/w), respectively, of soybean proteins (related to 10 g of initial product). The method has been proven to be precise with relative standard deviations (R.S.D.) for repeatability, intermediate precision, and internal reproducibility lower to 7.0%. Recoveries obtained for spiked meat products were close to 100% and no matrix interferences were observed. The application of the method to commercial heat-processed meat products in whose formulation soybean proteins were present yielded soybean protein contents ranging from 0.90% to 1.54%, below the maximum levels established by regulations.