Enhanced oxygen evolution at hydrous nickel oxide electrodes via electrochemical ageing in alkaline solution

The effect of electrochemically ageing hydrous nickel oxide films via slow repetitive potential multi-cycling across the main nickel (II/III) redox peak was investigated in an aqueous base environment using cyclic voltammetry and steady state polarisation curves in the oxygen evolution reaction (OER) region. Similarities between hydrous nickel oxide films and electroprecipitated ‘battery type’ nickel oxide were shown due to their similar change in redox and oxygen evolving properties as a result of film ageing. This ageing method was found to significantly enhance the OER performance of the hydrous nickel oxide electrode with the OER overpotential decreasing by 60 ± 2 mV and experiencing a 10 fold increase in OER rate for a fixed overpotential over that of an un-aged electrode. The OER turnover frequency for an aged electrode was found to be 1.16 ± 0.07 s^− 1 in comparison to 0.05 ± 0.003 s^− 1 for a hydrous nickel oxide electrode not subjected to ageing.     

Novel electrocatalysts for generating oxygen from alkaline water electrolysis

We have obtained spinel-type Co₃O₄ and La-doped Co₃O₄ in the form of thin film on Ni, using microwave-assisted synthesis, which dramatically exhibit very low overpotentials for the oxygen evolution reaction (OER). Investigations have shown that at the apparent current density of 100 mA cm⁻² in 1 mol dm⁻³ KOH at 25 °C, the new electrodes, Co₃O₄ (oxide loading = 3.4 ± 0.3 mg cm⁻²) and La-doped Co₃O₄ (oxide loading = 2.8 ± 0.4 mg cm⁻²), produce overpotentials, 235 ± 7 and 224 ± 8 mV, respectively. Such low overpotentials for the OER, to our knowledge, have not been found on any mixed oxide electrode material reported in literature till today. Small La addition improved the BET surface area and porosity of the oxide catalyst powder and reduced the charge transfer resistance for the OER on the electrode made of oxide powder.     

Synthesis and characterization of CaBi4Ti4O15 thin films annealed by microwave and conventional furnaces

CaBi₄Ti₄O₁₅ thin films were deposited by the polymeric precursor method and crystallized in a domestic microwave oven and conventional furnace. The films obtained for microwave energy are well-adhered, homogeneous and with good specularity when treated at 700 ^°C for 10 min. The microstructure and the structure of the films can be tuned by adjusting the crystallization conditions. When microwave oven is employed, the films presented bigger grains with mean grain size around 80 nm. For comparison, films were also prepared by the conventional furnace at 700 °C for 2 h.     

FeAgMo2O8 — A novel oxygen evolution catalyst material for alkaline metal–air batteries

This paper reports about FeAgMo₂O₈ — a novel oxygen evolution catalyst material for secondary (rechargeable) metal–air batteries. Bifunctional air electrodes were made using FeAgMo₂O₈ as a charging catalyst for oxygen evolution reaction (OER) and silverized carbon black (Ag/C) was employed as a discharging catalyst for oxygen reduction reaction (ORR). Corresponding air electrodes were investigated using 10 M KOH as an electrolyte. At current densities between 20 and 50 mA per cm² we observed discharging and charging voltages of 1.20 to 1.15 V and 1.96 to 2.05 V, respectively.     

New power source from fractional quantum energy levels of atomic hydrogen that surpasses internal combustion

Extreme ultraviolet (EUV) spectroscopy was recorded on microwave discharges of helium with 2% hydrogen. Novel emission lines were observed with energies of q·13.6 eV where q=1,2,3,4,6,7,8,9, or 11 or these lines inelastically scattered by helium atoms wherein 21.2 eV was absorbed in the excitation of He (1s²) to He (1s¹2p¹). These lines were identified as hydrogen transitions to electronic energy levels below the ‘ground’ state corresponding to fractional quantum numbers. Significant line broadening corresponding to an average hydrogen atom temperature of 33–38 eV was observed for helium–hydrogen discharge plasmas; whereas pure hydrogen showed no excessive broadening corresponding to an average hydrogen atom temperature of ≈3 eV. Since a significant increase in H temperature was observed with helium–hydrogen discharge plasmas, and energetic hydrino lines were observed at short wavelengths in the corresponding microwave plasmas that required a very significant reaction rate due to low photon detection efficiency in this region, the power balance was measured on the helium–hydrogen microwave plasmas. With a microwave input power of 30 W, the thermal output power was measured to be at least 300 W corresponding to a reactor temperature rise from room temperature to 900 °C within 90 s, a power density of 30 MW/m³, and an energy balance of about −4×10⁵ kJ/mol H₂ compared to the enthalpy of combustion of hydrogen of −241.8 kJ/mol H₂.     

Determination of the Tafel slope for oxygen evolution on boron-doped diamond electrodes

It has been reported that the oxygen evolution reaction (OER) on boron-doped diamond (BDD) electrodes appears at high overpotential and results in unusually high Tafel slope. In this work, we have studied the OER in 1 M HClO₄ on BDD macroelectrode and microelectrodes-array (MEA). The correction of the anodic polarization curve for ohmic drop has been performed on BDD macroelectrode taking into account the total uncompensated resistance of the studied system. On BDD MEA, no correction of the polarization curve was necessary due to the small contribution of ohmic drop to the measured potential. At low overpotential (<1.2 V), abnormally high Tafel slopes (340 and 680 mV dec⁻¹ on BDD MEA and BDD, respectively) have been observed. Such high slopes may result from the presence of surface redox couples/functional groups which act as a barrier for OER on BDD. In this potential region, the Tafel slope depends strongly on the state of the electrode surface. In the high overpotential region (>1.2 V), the Tafel slope has been found equal to 120 mV dec⁻¹, which is the theoretical value considering a first or a second electron transfer step as the rate determining step.     

Microwave-assisted C–H bond activation using a commercial microwave oven for rapid deuterium exchange labeling (C–H → C–D) in carbohydrates

Studies have shown that facile hydrogen → deuterium exchange in two model carbohydrates via stereospecific C–H bond activation could be achieved using a pre-sonicated Raney Nickel^® catalyst and microwave irradiation. Using a simple commercial microwave oven and a silica-gel bath, monosaccharide and disaccharide samples underwent isotopic exchange using microwave irradiation for sequential 15 s intervals. The influence of chilling between irradiation intervals was examined. The results revealed increasing levels of ²H incorporation without either epimerization or concomitant decomposition seen earlier in non-optimized experiments.     

Paramagnetic resonance and non-resonant microwave absorption in iron niobate

An electron paramagnetic resonance (EPR) study of FeNbO₄ powder samples in monoclinic phase (wolframite-type) at X-band (8.8–9.8 GHz), in the 90–300 K temperature range, is presented. For all the temperatures, the EPR spectrum shows a single line associated with Fe³⁺ ions. Changes in the lineshape of the EPR spectrum, which can be attributed to Fe²⁺ ions, are detected at low temperatures. This behavior can be ascribed to a strong magnetic dipolar interaction between Fe²⁺ and Fe³⁺ ions. The non-resonant microwave absorption techniques: magnetically-modulated microwave absorption spectroscopy (MAMMAS) and low-field microwave absorption spectroscopy (LFMAS), were used for a further knowledge on this material. MAMMAS response suggests also the presence of Fe²⁺ ions, that originates a change in microwave absorption regime for T < T_p (=140 K), associated with the presence of short-range magnetic correlations. LFMAS spectra showed a linear behavior with positive slope and non-hysteretic traces. The profiles obtained by plotting the slope vs. temperature of the LFMAS line are similar to those detected by the MAMMAS technique, confirming that both types of measurement show the same processes of absorption.     

Thermal reactivity of cis- and trans-bis(triphenylgermyl)bis(tertiary phosphine)platinum(II)

The complex cis-Pt(Ph₃Ge)₂(PMe₂Ph)₂ underwent smooth isomerization to give the trans-isomer at room temperature via an associative five-coordinated intermediate. Thermodynamic parameters and activation energy for the cis to trans isomerization were obtained, ΔH^# = 105 kJ mol⁻¹, ΔS^# = 12.5 J mol⁻¹ K⁻¹, and Ea = 107 kJ mol⁻¹, respectively. Heating of trans-Pt(Ph₃Ge)₂(PMe₂Ph)₂ at 50 °C for 36 days produced trans-PtPh(Ph₃Ge)(PMe₂Ph)₂ followed by the formation of trans-PtPh₂(PMe₂Ph)₂, Pt(PMe₂Ph)₄, and Ph₄Ge finally via elimination of the phenyl group from Ph₃Ge ligand with liberation of the Ph₂Ge unit and subsequent reductive elimination of the remaining Ph₃Ge ligand at 80 °C for 1 month.     

High capacity and excellent cyclability of vanadium (IV) oxide in lithium battery applications

A VO₂ · 0.43H₂O powder with a flaky particle morphology was synthesized via a hydrothermal reduction method. It was characterized by scanning electron microscopy, electron energy loss spectroscopy, and thermogravimetric analysis. As an electrode material for rechargeable lithium batteries, it was used both as a cathode versus lithium anode and as an anode versus LiCoO₂, LiFePO₄ or LiNi_0.5Mn_1.5O₄ cathode. The VO₂ · 0.43H₂O electrode exhibits an extraordinary superiority with high capacity (160 mAh g^?1), high energy efficiency (95%), excellent cyclability (142.5 mAh g^?1 after 500 cycles) and rate capability (100 mAh g^?1 at 10 C-rate).     

A novel approach for determining total titanium from titanium dioxide nanoparticles suspended in water and biosolids by digestion with ammonium persulfate

Titanium dioxide (i.e. TiO₂) in nano-form is a constituent of many nanomaterials that are used in sunscreens, cosmetics, industrial products and in biomedical applications. Quantification of TiO₂ nanoparticles in various matrixes is a topic of great interest for researchers studying the potential health and environmental impacts of nanoparticles. However, analysis of TiO₂ as Ti⁴⁺ is difficult because current digestion techniques require use of strong acids that may be a health and safety risk in the laboratory. To overcome this problem, we developed a new method to digest TiO₂ nanoparticles using ammonium persulfate as a fusing reagent. The digestion technique requires short times to completion and optimally requires only 1 g of fusing reagent. The fusion method showed >95% recovery of Ti⁴⁺ from 6 μg mL^?1 aqueous suspensions prepared from 10 μg mL^?1 suspension of different forms of TiO_2, including anatase, rutile and mixed nanosized crystals, and amorphous particles. These recoveries were greater than open hot-plate digestion with a tri-acid solution and comparable to microwave digestion with a tri-acid solution. Cations and anions commonly found in natural waters showed no significant interferences when added to samples in amounts of 10 ng to 110 mg, which is a much broader range of these ions than expected in environmental samples. Using ICP-MS for analysis, the method detection limit (MDL) was determined to be 0.06 ng mL^?1, and the limit of quantification (LOQ) was 0.20 ng mL^?1. Analysis of samples of untreated and treated wastewater and biosolids collected from wastewater treatment plants yielded concentrations of TiO₂ of 1.8 and 1.6 ng mL^?1 for the wastewater samples, respectively, and 317.4 ng mg^?1 dry weights for the biosolids. The reactions between persulfate ions and TiO₂ were evaluated using stoichiometric methods and FTIR and XRD analysis. A formula for the fusing reaction is proposed that involves the formation of sulfate radicals.     

Electrospun zirconia-embedded carbon nanofibre for high-sensitive determination of methyl parathion

Carbon nanofibers embedded with ultrafine zirconia nanoparticles (ZrO₂-CNFs) are fabricated via a new methodology. Polyvinylpyrrolidone (PVP) and polymethylmethacrylate (PMMA) binary polymers containing zirconium n-butoxide are first dissolved in dimethylformamide, and the resulting solution is electrospun and heat-treated. The tetragonal zirconia nanoparticles formed, with a size of 5 ± 2 nm in diameter, are uniformly distributed in the carbon nanofibres. Using Nafion as an additive, ZrO₂-CNFs are drop-cast onto the glassy carbon electrode (ZrO₂-CNF/GCE) and the modified electrode is then applied to detect methyl parathion (MP) using differential pulse voltammetry. Two linear relationships are found at the concentration ranges of 1 × 10^− 9–2 × 10^− 8 g/L and 2 × 10^− 8–2 × 10^− 7 g/L, with a detection limit of 3.4 × 10^− 10 g/L (S/N > 3). The electrospun-based ZrO₂-CNF is a very promising coating material for electrochemical sensing of organophosphorus compounds.     

Enhancement of electrochemical performance and thermal compatibility of GdBaCo2/3Fe2/3Cu2/3O5+δ cathode on Ce1.9Gd0.1O1.95 electrolyte for IT-SOFCs

Transition-metal doped double-perovskite structure oxides GdBaCo_2/3Fe_2/3Ni_2/3O_5+δ (FN-GBCO), GdBaCo_2/3Fe_2/3Cu_2/3O_5+δ (FC-GBCO), GdBaCoCuO_5+δ (C-GBCO) and pristine GdBaCo₂O_5+δ (GBCO) were synthesized via a citrate combustion method. The thermal-expansion coefficient (TEC) and electrochemical performance of the oxides were investigated as potential cathodes for intermediate-temperature solid oxide fuel cells (IT-SOFCs). The TEC exhibited by the FC-GBCO cathode up to 900 °C is 14.6 × 10^?6 °C^?1, which is lower than the value of GBCO (19.9 × 10^?6 °C^?1). Area specific resistances (ASR) of 0.165 Ω cm² at 700 °C and 0.048 Ω cm² at 750 °C were achieved for the FC-GBCO cathode on a Ce_0.9Gd_0.1O_1.95 (CGO) electrolyte. An electrolyte supported (300 μm thick) single-cell configuration of FC-GBCO/CGO/Ni-CGO attained a maximum power density of 435 mW cm^?2 at 700 °C. The unique composition of GBCO co-doped with Fe and Cu ions in the Co sites exhibited reduced TEC and enhancement of electrochemical performance and good chemical compatibility with CGO, and this composition is proving to be a potential cathode for IT-SOFCs.     

Efficient immobilization of 9,10-anthraquinonyl moiety at solid interfaces through 2-(bromomethyl)anthraquinone one-electron cleavage

We report here a new and very efficient method for the coverage of different carbon materials with 9,10-anthraquinone attached via a methylene linker. The method is based on one-electron reduction of 2-(bromomethyl)anthraquinone (AQ-CH₂-Br) to a free radical AQ–CH₂ which was readily achieved using propylene carbonate (PC) as solvent containing tetrabutylammonium iodide. This way, the radical AQ–CH₂ adds to the abovementioned carbons forming very stable and dense covalently bound anhraquinonyl methane layers (Г ≈ 2 × 10^− 9 mol cm^− 2). The grafting could be performed by constant potential electrolyses (q < 0.5 × 10^− 3 C mm^− 2).     

The role of the double bond position in hydroboration using HBBr2 · SMe2, HBCl2 · SMe2 and H2BBr · SMe2: A detailed kinetic and mechanistic study

Hydroboration reactions of 4-octene with HBBr₂ · SMe₂, HBCl₂ · SMe₂ and H₂BBr · SMe₂ in CH₂Cl₂ were studied as function of concentration and temperature and compared with those of 1-octene. On average, hydroboration with dihaloborane proceeded 16 times slower for 4-octene than for 1-octene. In the case of the reactions with the monohaloborane, this factor is halved. This can be explained by the difference in the relative rates of dissociates of Me₂S from the dihaloborane and a monohaloborane complex, respectively. The reactions involving H₂BBr · SMe₂ also exhibited a k_?2 value, an indication of the presence of a parallel reaction, most likely a rearrangement process facilitating isomerization by way of a π-complex. The moderate ΔH^≠ values accompanied by small ΔS^≠ values (94 ± 4 kJ mol^?1, ?3 ± 13 J K^?1 mol^?1 for HBBr₂ · SMe₂; 93 ± 1 kJ mol^?1, ?17 ± 4 J K^?1 mol^?1 for HBCl₂ · SMe₂ and in the case of H₂BBr · SMe₂, 90 ± 13 kJ mol^?1, +12 ± 44 J K^?1 mol^?1 and 83 ± 13 kJ mol^?1, ?24 ± 45 J K^?1 mol^?1, respectively, for the k₂ and k_?2 processes) imply a process that is dissociatively dominated, with the overall mode of activation being interchange dissociative (I_d).     

On oxoacidic properties and solubilities of beryllium and magnesium oxides in molten (CsCs + KCl + NaCl) eutectic at T = 783 K

Reactions of Be²⁺ and Mg²⁺ with O^2– in molten eutectic mixture (CsCs + KCl + NaCl) (0.455:0.245:0.30) at T = 783 K were studied by a potentiometric method using Pt(O₂)|ZrO₂(Y₂O₃) indicator electrode. Addition of O^2– ions to the melt containing Mg²⁺ results in precipitation of MgO (pK_s,MgO = 11.89 ± 0.3, molality) whereas interaction of Be²⁺ with O^2– is accompanied with sequential formation of Be₂O²⁺ (pK = 15.68 ± 0.5, molality) and precipitation of BeO (pK_s,BeO = 9.62 ± 0.3, molality). On the basis of the obtained and known data pK_s,MgO–T⁻¹ dependence in molten (CsCs + KCl + NaCl) eutectic is constructed. The slope of the said dependence in T/K = (from 583 to 1073) range is in good agreement with the value predicted by the Shreder equation, that extends the range of use of the Shreder equation for predictions of metal oxide solubilities in molten halides.     

Photocatalytic reduction of cadmium over CuFeO2 synthesized by sol–gel

The Cd²⁺ photo-electrodeposition was successfully carried out in air-equilibrated aqueous CuFeO₂ suspension. The delafossite CuFeO₂ is p-type semiconductor characterized by a low optical gap, properly matched to the sun spectrum, and a long term chemical stability in neutral solution. It has been elaborated by the sol–gel technique where the specific surface area is increased via the surface/bulk ratio. The TG/DSC plots and IR spectra show that the solid phases are formed only at temperatures exceeding 400 and at 700 °C, the system is mixed phases. When fired at 950 °C under nitrogen flow, the delafossite has been identified (CuO + CuFe₂O₄ → CuFeO₂ + ½O₂). All the XRD lines index in a hexagonal unit cell with the lattice constants a = 284.2 and c = 169.4 pm. The photocurrent onset potential (+0.35 V_SCE) is close to the flat band potential (+0.23 V_SCE) determined from the capacitance measurement. CuFeO₂/Cd²⁺ solution is a self photo-driven system, the absorption of light promotes electrons into CuFeO₂–CB with a potential (?0.93 V_SCE) sufficient to reduce Cd²⁺. This occurs because of the dark Cd²⁺ adsorption on the surface powder. The system was optimized with respect to the following physical parameters: pH 6.8, Cd²⁺ (100 ppm) and a mass concentration C_m (1 mg catalyst/ml solution). The hetero-system CuFeO₂/TiO₂ has been also reported for a comparative purpose. Prolonged irradiation (>50 min) was accompanied by a pronounced decrease in the rate of Cd-deposition owing to the competitive water reduction. Indeed, the generated bi-functional CuFeO₂/Cd particles account for the low over-potential of hydrogen and favour its evolution in aqueous solution.     

A Li3V2(PO4)3/C thin film with high rate capability as a cathode material for lithium-ion batteries

A monoclinic lithium vanadium phosphate (Li₃V₂(PO₄)₃) and carbon composite thin film (LVP/C) is prepared via electrostatic spray deposition. The film is studied with X-ray diffraction, scanning and transmission electron microscopy and galvanostatic cell cycling. The LVP/C film is composed of carbon-coated Li₃V₂(PO₄)₃ nanoparticles (50 nm) that are well distributed in a carbon matrix. In the voltage range of 3.0–4.3 V, it exhibits a reversible capacity of 118 mA h g^?1 and good capacity retention at the current rate of 1 C, while delivers 80 mA h g^?1 at 24 C. These results suggest a practical strategy to develop new cathode materials for high power lithium-ion batteries.     

Efficient passivation of SnO2 nano crystallites by Indoline D-149 via dual chelation

For the first time in SnO₂ based dye solar cells, here we report, efficiency exceeding 3% of the cells consisting with Indoline D-149 dye with unmodified SnO₂ nano-crystallites. The cells sensitized with metal free D-149 dye together with liquid electrolyte comprising with 0.5 M tetrapropyl ammonium iodide and 0.05 M iodine in a mixture of acetonitrile and ethylene carbonate (1:4 by volume) delivered a short circuit current density of 10.4 mA cm^?2 with an open circuit voltage of 530 mV under the illumination of 100 mW cm^?2 (AM1.5) having an efficiency of 3.1%. As evident from the FTIR measurement, strong surface passivation of recombination centers of SnO₂ crystallites due to the dual mode of attachment of dye molecules to the surface of SnO₂ via both COOH and S–O direct bond might be the possible reason for this enhancement in these SnO₂ based cells.     

Selective and rapid detection of triacetone triperoxide by double-step chronoamperometry

A selective detector for the improvised explosive, triacetone triperoxide is proposed. This is based on the rapid redox reaction of peroxides (hexamethylene triperoxide diamine, benzoyl peroxide, t-butyl peroxide, triacetone triperoxide and H₂O₂) with bromide at 55 °C. Consumption of bromide is indicative of the reduction of the R–O–O–R moiety, the appearance of Br₂ was found for all except for triacetone triperoxide. The latter was found to breakdown to acetone which rapidly reacts with Br₂ producing bromoacetones. The lack of Br₂ production is unique to triacetone triperoxide. Double step chronoamperometry (E₁ = 700 mV, E₂ = 960 mV (vs. Ag/AgCl)) allows for the quantitation of bromine (Br₂ + 2e^? ? 2Br^?) and bromide (2Br^? ? Br₂ + 2e^?) respectively. The results yielded a detection limit of 8.5 µM for triacetone triperoxide with a sensitivity of 0.026 µA µM^? 1. The detection limits of 16.3 µM and 14.9 µM were found respectively for HMTD and H₂O₂ based on the appearance of Bromine. These results indicate a possibility to develop a handheld sensor for TATP dermination.