A novel tailored bimodal porous silica with well-defined inverse opal microstructure and super-microporous lamellar nanostructure

A novel tailored bimodal porous silica with well-defined inverse opal microstructure and super-microporous lamellar nanostructure has been successfully synthesized by simultaneous application of three-dimensional order polystyrene (PS) beads and an amphiphilic ionic liquid (AIL) as templates.     

Fine control of the porous structure and chromatographic properties of monodisperse macroporous poly(styrene-co-divinylbenzene) beads prepared using polymer porogens

The porous structure of monodisperse macroporous beads can be controlled by using soluble polymers with well-defined structural characteristics as part of the porogenic mixture. In general, the use of linear polystyrene as a porogen in the preparation of poly (styrene-co-divinylbenzene) beads shifts the pore size distribution towards larger pores. While a direct correlation between pore size and molecular weight of the porogen has been established, the chemical composition of the polymer porogen has no effect on the porous and chromatographic properties of the beads. These findings suggest that the average molar volume of the porogenic system is important while the miscibility of the polymer porogen with the crosslinked polymer that is formed is of little relevance. © 1994 John Wiley & Sons, Inc.     

Organized monolayer of thermosensitive microgel beads prepared by double-template polymerization

A 2D close-packed array of thermosensitive microgel beads was prepared by the double-template polymerization method. First, a 2D colloidal crystal of silica beads with 10 microm diameter was obtained by the solvent evaporation method. This monolayer of colloidal crystals can serve as the first template for the preparation of macroporous polystyrene. The macroporous polystyrene trapping the crystalline order can be used as a negative template for fabricating gel beads arrays. A functional surface using thermosensitive poly(N-isopropylacrylamide) gel beads array was fabricated by the double-template polymerization method.     

磁场和稀土Ce介入下化学镀Co-Ni-B合金的晶化行为

化学镀钴-镍-硼;晶体结构;稀土重金属;磁场和稀土Ce介入下化学镀Co-Ni-B合金的晶化行为     

Inverse Suspension Polymerization as a New Tool for the Synthesis of Ion‐Imprinted Polymers

Ion‐imprinted polymer beads are prepared for the first time by inverse suspension polymerization in mineral oil using nickel(II) as the template ion. As water is not used as the continuous phase, this new route of synthesis avoids the risk that the ion template leaves the suspension for the aqueous phase. The leaching of nickel from the resin beads is very good due to the large porosity of the polymer beads. The ratio between the ligand and the crosslinker has been increased leading to higher adsorption capacities. Comparing these values with those of the non‐imprinted polymers and studying the effect of some interfering ions proves that an optimum can be found for the ratio ligand/crosslinker.     

Highly active nanoreactors: nanomaterial encapsulation based on confined catalysis

It happens inside: highly active nanoreactors are prepared by encapsulating dendritic Pt nanoparticles (NPs) grown on a polystyrene template inside hollow porous silica capsules. The catalytic activity of these Pt NPs is preserved after encapsulation and template removal. Different metals, such as Ni, can thus be reduced inside the capsules, thereby leading to the formation of composites with tunable magnetic properties.     

MOF-Mediated Fabrication of a Porous 3D Superstructure of Carbon Nanosheets Decorated with Ultrafine Cobalt Phosphide Nanoparticles for Efficient Electrocatalysis and Zinc–Air Batteries

Superstructures have attracted great interest owing to their potential applications. Herein, we report the first scalable preparation of a porous nickel-foam-templated superstructure of carbon nanosheets decorated with ultrafine cobalt phosphide nanoparticles. Uniform two-dimensional (2D) Co-metal organic framework (MOF) nanosheets (Co-MNS) grow on nickel foam, followed by a MOF-mediated tandem (carbonization/phosphidation) pyrolysis. The resulting superstructure has a porous 3D interconnected network with well-arranged 2D carbon nanosheets on it, in which ultrafine cobalt phosphide nanoparticles are tightly immobilized. A single piece of this superstructure can be directly used as a self-supported electrode for electrocatalysis without any binders. This “one-piece” porous superstructure with excellent mass transport and electron transport properties, and catalytically active cobalt phosphide nanoparticles with ultrasmall size (3–4 nm), shows excellent trifunctional electrocatalytic activities for oxygen evolution reaction (OER), hydrogen evolution reaction (HER), and oxygen reduction reaction (ORR), achieving great performances in water splitting and Zn–air batteries.     

Ethylene polymerization with porous polystyrene spheres supported Cp2ZrCl2 catalyst

A catalyst with porous polystyrene beads supported Cp₂ZrCl₂ was prepared and tested for ethylene polymerization with methylaluminoxane as a cocatalyst. By comparison, the porous supported catalyst maintained higher activity and produced polyethylene with better morphology than its corresponding solid supported catalyst. The differences between activities of the catalysts and morphologies of the products were reasonably explained by the fragmentation processes of support as frequently observed with the inorganic supported Ziegler–Natta catalysts. Investigation into the distribution of polystyrene in the polyethylene revealed the fact that the porous polystyrene supported catalyst had undergone fragmentation during polymerization. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3313–3319, 2003     

溶胶浸渍模板法制备有序多孔氧化钛、氧化锌薄膜

采用溶胶浸渍模板法制备了有序多孔的氧化钛(TiO₂)和氧化锌(ZnO)薄膜。首先，在洁净的玻璃基片上通过浸渍-提拉工艺组装有序的聚苯乙烯微球(PS)阵列模板；然后再采用溶胶浸渍法将TiO₂和ZnO溶胶灌充到PS模板微球的间隙内；最后通过煅烧去除PS而得多孔薄膜。采用SEM观察了薄膜的表面形貌，并用XRD对薄膜的性能进行了表征。结果表明，溶胶的浓度对薄膜形貌有着显著的影响。经煅烧后，TiO₂和ZnO薄膜分别为锐钛矿和六方纤锌矿结构。此外，对模板的组装及溶胶的灌注过程进行了分析。     

Hollow silica capsules with well-defined asymmetric windows in the shell

A straightforward and effective approach to fabricate porous silica capsules with well-defined asymmetric windows in the shell using raspberry-like templates has been developed. This process begins with the formation of a hierarchical template by chemically coupling a large polystyrene sphere to an ensemble of small, polystyrene latex spheres. The hierarchical template in conjunction with a hard templating method and spin-coating leads to silica capsules with well-defined, asymmetric pores (windows) in the outer shell. Proof-of-principle of this approach has been demonstrated using a 1500/110 nm hierarchical template. The silica capsules thus produced were characterized with scanning electron microscopy and STEM. The diameter of the capsules was ~1400 nm, and the outer opening of the windows was ~100 nm in size, consistent with the diameters of the core and satellite spheres considering the shrinkage due to the calcination. The inner opening was ~30 nm, which gives rise to an asymmetry factor, defined as the diameter of the outer window to the diameter of the inner window, of ~3. In another example, surface-bound capsules with an asymmetry factor of ~1 were made. Collectively, these windows can provide efficient pathways to connect the inside of the capsule to the outside and have potential for asymmetric diffusion and rectification.     

Magnetic porous carbon derived from Co‐doped metal–organic frameworks for the magnetic solid‐phase extraction of endocrine disrupting chemicals

Metal–organic frameworks‐5 (MOF‐5) was explored as a template to prepare porous carbon due to its high surface area, large pore volume, and permanent nanoscale porosity. Magnetic porous carbon, Co@MOF‐5‐C, was fabricated by the one‐step direct carbonization of Co‐doped MOF‐5. After carbonization, the magnetic cobalt nanoparticles are well dispersed in the porous carbon matrix, and Co@MOF‐5‐C displays strong magnetism (with the saturation magnetization intensity of 70.17emu/g), high‐specific surface area, and large pore volume. To evaluate its extraction performance, the Co@MOF‐5‐C was applied as an adsorbent for the magnetic solid‐phase extraction of endocrine disrupting chemicals, followed by their analysis with high‐performance liquid chromatography. The developed method exhibits a good linear response in the range of 0.5–100 ng/mL for pond water and 1.0–100 ng/mL for juice samples. The limits of detection (S/N  = 3) for the analytes were in the range of 0.1–0.2 ng/mL.     

Thermo-responsive polymer brush-grafted porous polystyrene beads for all-aqueous chromatography

Poly(N-isopropylacrylamide) (PIPAAm) brush-grafted porous polystyrene beads with variable grafted polymer densities were prepared using surface-initiated atom transfer radical polymerization (ATRP) for applications in thermo-responsive chromatography. Utilization of these grafted beads as a stationary phase in aqueous chromatographic analysis of insulin provides a graft density-dependent analyte retention behavior. The separations calibration curve on PIPAAm-grafted polystyrene was obtained using pullulan standards and exhibited inflection points attributed to analyte diffusion into bead pores and partitioning into grafted PIPAAm brush surfaces. Presence of these inflection points supports a separation mechanism where insulin penetrates pores in polystyrene beads and hydrophobically interacts with PIPAAm brushes grafted within the pores. Control of PIPAAm brush graft density on polystyrene facilitates effective aqueous phase separation of peptides based on thermally modulated hydrophobic interactions with grafted PIPAAm within stationary phase pores. These results indicated that PIPAAm brush-grafted porous polystyrene beads prepared by surface-initiated ATRP was effective stationary phase of thermo-responsive chromatography for aqueous phase peptide separations.     

Preparation and functionalization of reactive monodisperse macroporous poly(chloromethylstyrene-co-styrene-co-divinylbenzene) beads by a staged templated suspension polymerization

Reactive monodisperse porous poly(chloromethylstyrene-co-styrene-co-divinylbenzene) beads have been prepared by a staged templated suspension polymerization method with different concentrations of linear polystyrene porogen and chloromethylstyrene in the polymerization mixture. The presence of a small amount of linear polystyrene in the polymerization mixture leads to a dramatic increase in both the pore size and the pore volume of the resulting beads. In contrast, addition of chloromethylstyrene leads to lower surface areas and smoother surfaces due to the reduced compatibility between the polystyrene porogen and the newly formed crosslinked chains. The modification of chloromethylstyrene beads by Gabriel synthesis to obtain aminated beads has also been studied. The final number of primary amino groups is related to the starting concentration of functional benzyl chloride moieties rather than to the porous properties. Both π-basic and π-acidic type chiral selectors, (R)-1-(1-naphthyl)-ethylamine and (R)-N-(3,5-dinitrobenzoyl)phenylglycine, respectively, have been attached to the amino functionalized beads, and the resulting chiral beads have been used in the model HPLC separations of enantiomers. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 2631–2643 1997     

Template evaporation method for controlling anatase nanocrystal size in ordered macroporous TiO2

The importance of pure-phase titanium oxide materials as catalysts, sensors, and photonic band-gap materials has been growing steadily. Recently, more attention has been focused on nanostructured titanium oxide showing controlled and periodic porosity on a nanometric scale. The nanocrystal size control of porous nanostructured titanium oxide in an anatase form is a crucial step for the organic template method. Simple template removal by evaporation in an inert atmosphere is reported in this article and compared with the calcination technique usually reported in the literature. The proposed method allows the formation of a double-porous (macro and meso) anatase phase. We demonstrate that it highly preserves the macropore order into a titanium oxide material and induces narrowly dispersed mesopores by controlling the nano-crystal size that is kept around 6 nm. For the proposed method, polystyrene beads are particularly suitable as templates, being evaporated in the temperature range of anatase existence. The final high surface area makes the materials appealing for applications as photocatalysts or sensors.     

Enhanced magnetism in electrodeposited-based CoNi composites containing high percentage of micron hard-magnetic particles

CoNi–barium ferrite magnetic composites with a high percentage of micrometric particles have been prepared by electrodeposition over silicon-based substrates. A cationic surfactant synthesized in our laboratory (4-ethylazobenzene-4′-(oxyethyl)trimethylammonium iodide-AZTMAI) has been used in order to favour the inclusion of magnetic particles into the alloy deposit. This surfactant reduces during cobalt–nickel electrodeposition and it is not embedded into the deposit. Moderate surfactant concentrations (1–5 g l⁻¹), room temperature, the application of a magnetic field during the electrodeposition and a double-pulse technique favour the maximum incorporation of barium ferrite up to around 30–35 wt%. Magnetic properties of composites prepared tend to hard-magnetic ones, with different magnetization curves when silicon/seed-layer/composite samples are oriented parallel or perpendicularly to the applied magnetic field. Constricted-type magnetization curves were obtained.     

Preparation of mesostructured siloxane-organic hybrid films with ordered macropores by templated self-assembly

Novel hierarchically ordered siloxane-based hybrid films with well-defined macropores and mesostructured pore walls have been prepared by the self-assembly process using oligomeric siloxane precursors bearing alkyl chains (CnH2n+1Si(OSi(OMe)3)3) in the presence of polystyrene opal films as a template. Either a two-dimensional (2D) hexagonal structure or a lamellar structure was formed depending on the alkyl chain length of the precursors (n = 10 and 16, respectively). In both of the films, the mesostructures were oriented along the spherical surface of the template and were retained after removal of the template. Calcination of the 2D hexagonal hybrid produced ordered porous silica with both macro- and microporosities. The lamellar hybrid film exhibited a unique property of accommodating alkyl alcohols with an expansion of the interlayer spacings. These results provide a new concept for designing hierarchical hybrid materials that are potentially applicable as adsorbents, catalysts, sensors, and photonic crystals.     

Magnetic properties of nickel clusters

We use a variation of the Stern-Gerlach experiment to study the magnetic behavior of transition metal clusters. We report measurements of the magnetic properties of nickel clusters as a function of cluster size, vibrational temperature, and applied magnetic field. Results for these nickel clusters resemble those previously published for cobalt clusters in that superparamagnetic behavior is observed. As is the case for cobalt clusters, nickel clusters are observed to have magnetic moments per atom that are greater than the bulk value.     

Preparation of macroporous functionalized polymer beads by a multistep polymerization and their application in zirconocene catalysts for ethylene polymerization

Macroporous functionalized polymer beads of poly(4‐vinylpyridine‐co‐1,4‐divinylbenzene) [P(VPy‐co‐DVB)] were prepared by a multistep polymerization, including a polystyrene (PS) shape template by emulsifier‐free emulsion polymerization, linear PS seeds by staged template suspension polymerization, and macroporous functionalized polymer beads of P(VPy‐co‐DVB) by multistep seeded polymerization. The polymer beads, having a cellular texture, were made of many small, spherical particles. The bead size was 10–50 μm, and the pore size was 0.1–1.5 μm. The polymer beads were used as supports for zirconocene catalysts in ethylene polymerization. They were very different from traditional polymer supports. The polymer beads could be exfoliated to yield many spherical particles dispersed in the resulting polyethylene particles during ethylene polymerization. The influence of the polymer beads on the catalytic behavior of the supported catalyst and morphology of the resulting polyethylene was investigated. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 873–880, 2003     

4-cyanoimidazolate: a new pseudo-cyanide?

Because of its exobidentate nature, pK(a), and electronic properties, 4-cyanoimidazole has been examined as a ligand and as a pseudo-cyanide. The ligand reacts readily as an anion with both cobalt and nickel ions in solution to form coordination polymers. The magnetic susceptibility and thermal stability of these materials are reported. 4-Cyanoimidazolate forms a hexakis complex with nickel, to form the first observed hexakis imidazolate nickelate complex.     

Magnetic molecularly imprinted polymer beads prepared by microwave heating for selective enrichment of β-agonists in pork and pig liver samples

Novel magnetic molecularly imprinted polymer (MIP) beads using ractopamine as template for use in extraction was developed by microwave heating initiated suspension polymerization. Microwave heating, as an alternative heating source, significantly accelerate the polymerization process. By incorporating magnetic iron oxide, superparamagnetic composite MIP beads with average diameter of 80 μm were obtained. The imprinted beads were then characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis and vibrating sample magnetometer. Highly cross-linked porous surface and good magnetic property were observed. The adsorption isotherm modeling was performed by fitting the data to Freundlich isotherm model. The binding sites measured were 3.24 μmol g⁻¹ and 1.17 μmol g⁻¹ for the magnetic MIP beads and the corresponding non-imprinted magnetic beads, respectively. Cross-selectivity experiments showed the recognition ability of the magnetic MIP beads to analytes is relative to degree of molecular analogy to the template. Finally, this magnetic MIP bead was successfully used for enrichment of ractopamine, isoxsuprine and fenoterol from ultrasonically extracted solution of pork and pig liver followed by high performance chromatography with fluorescence detection. The proposed method presented good linearity and the detection limits was 0.52-1.04 ng mL⁻¹.The recoveries were from 82.0% to 90.0% and from 80.4% to 86.8% for the spiked pork and pig liver, respectively, with the RSDs of 5.8-10.0%. Combination of the specific adsorption property of the MIP material and the magnetic separation provided a powerful analytical tool of simplicity, flexibility, and selectivity.