Partially reduced SnO2 nanoparticles anchored on carbon nanofibers for high performance sodium-ion batteries

One-dimensional (1-D) carbon nanofibers anchored with partially reduced SnO₂ nanoparticles (SnO₂/Sn@C) were successfully synthesized through a simple electrospinning method followed by carbon coating and thermal reduction processes. The partially reduced Sn frameworks, combined with the carbon fibers, provide a more favorable mechanism for sodiation/desodiation than SnO₂. As a result, SnO₂/Sn@C exhibits a high reversible capacity (536 mAh g^− 1 after 50 cycles) and an excellent rate capability (396 mAh g^− 1 even at 2 C rate) when evaluated as an anode material for sodium-ion batteries (SIBs).     

SnO2@MWCNT nanocomposite as a high capacity anode material for sodium-ion batteries

We report the synthesis and characterization of SnO₂@multiwalled carbon nanotubes (MWCNTs) nanocomposite as a high capacity anode material for sodium-ion battery. SnO₂@MWCNT nanocomposite was synthesized by a solvothermal method. SEM and TEM analyses show the uniform distribution of SnO₂ nanoparticles on carbon nanotubes. When applied as anode materials in Na-ion batteries, SnO₂@MWCNT nanocomposite exhibited a high sodium storage capacity of 839 mAh g^− 1 in the first cycle. SnO₂@MWCNT nanocomposite also demonstrated much better cycling performance than that of bare SnO₂ nanoparticles and bare MWCNTs. Furthermore, the nanocomposite electrode also showed a good cyclability and an enhanced Coulombic efficiency on cycling.     

Structural and electrochemical properties of a porous nanostructured SnO2 film electrode for lithium-ion batteries

A B₂O₃-doped SnO₂ thin film was prepared by a novel experimental procedure combining the electrodeposition and the hydrothermal treatment, and its structure and electrochemical properties were investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) analysis, energy dispersive X-ray (EDX) spectroscopy and galvanostatic charge–discharge tests. It was found that the as-prepared modified SnO₂ film shows a porous network structure with large specific surface area and high crystallinity. The results of electrochemical tests showed that the modified SnO₂ electrode presents the largest reversible capacity of 676 mAh g^?1 at the fourth cycle, close to the theoretical capacity of SnO₂ (790 mAh g^?1); and it still delivers a reversible Li storage capacity of 524 mAh g^?1 after 50 cycles. The reasons that the modified SnO₂ film electrode shows excellent electrochemical properties were also discussed.     

Optical and electrical conducting properties of Polyaniline/Tin oxide nanocomposite

Polyaniline(PANI)/Tin oxide (SnO₂) hybrid nanocomposite with a diameter 20–30 nm was prepared by co-precipitation process of SnO₂ through in situ chemical polymerization of aniline using ammonium persulphate as an oxidizing agent. The resulting nanocomposite material was characterized by different techniques, such as X-ray diffraction (XRD), Transmission Electron Microscopy (TEM), Fourier Transform Infrared spectroscopy (FT-IR) and Ultraviolet–Visible spectroscopy (UV–Vis), which offered the information about the chemical structure of polymer, whereas electron microscopy images provided information regarding the morphology of the nanocomposite materials and the distribution of the metal particles in the nanocomposite material. SEM observation showed that the prepared SnO₂ nanoparticles were uniformly dispersed and highly stabilized throughout the macromolecular chain that formed a uniform metal-polymer nanocomposite material. UV–Vis absorption spectra of PANI/SnO₂ nanocomposites were studied to explore the optical behavior after doping of nanoparticles into PANI matrix. The incorporation of SnO₂ nanoparticles gives rise to the red shift of π–π¹ transition of polyaniline. Thermal stability of PANI and PANI/SnO₂ nanocomposite was investigated by thermogravimetric analysis (TGA). PANI/SnO₂ nanocomposite observed maximum conductivity (6.4 × 10^?3 scm^?1) was found 9 wt% loading of PANI in SnO₂.     

Mesoporous organo-silica nanoarray for energy storage media

A SnO₂–mesoporous organo-silica nanoarray (MOSN) composite was prepared by surfactant mediated synthesis combined with a sol–gel vacuum suction method in which SnO₂ has been successfully incorporated inside the periodic nanoholes in the MOSN or coated on its surface. The MOSN with a high aspect ratio of length to width could not only maintain its structure but also effectively accommodate the volume expansion of the SnO₂ during electrochemical reactions with Li⁺. The SnO₂–MOSN composite showed a higher reversible capacity of 420 mA h g⁻¹ with greatly improved capacity retention and lower initial irreversible capacity compared to SnO₂ powder. This interesting anodic performance of SnO₂–MOSN composite supports the potential use of MOSN for lithium ion batteries.     

Efficient passivation of SnO2 nano crystallites by Indoline D-149 via dual chelation

For the first time in SnO₂ based dye solar cells, here we report, efficiency exceeding 3% of the cells consisting with Indoline D-149 dye with unmodified SnO₂ nano-crystallites. The cells sensitized with metal free D-149 dye together with liquid electrolyte comprising with 0.5 M tetrapropyl ammonium iodide and 0.05 M iodine in a mixture of acetonitrile and ethylene carbonate (1:4 by volume) delivered a short circuit current density of 10.4 mA cm^?2 with an open circuit voltage of 530 mV under the illumination of 100 mW cm^?2 (AM1.5) having an efficiency of 3.1%. As evident from the FTIR measurement, strong surface passivation of recombination centers of SnO₂ crystallites due to the dual mode of attachment of dye molecules to the surface of SnO₂ via both COOH and S–O direct bond might be the possible reason for this enhancement in these SnO₂ based cells.     

Polyol-mediated synthesis of ultrafine tin oxide nanoparticles for reversible Li-ion storage

A simple, cheap and versatile, polyol-mediated fabrication method has been extended to the synthesis of tin oxide nanoparticles on a large scale. Ultrafine SnO₂ nanoparticles with crystallite sizes of less than 5 nm were realized by refluxing SnCl₂ · 2H₂O in ethylene glycol at 195 °C for 4 h under vigorous stirring in air. The as-prepared SnO₂ nanoparticles exhibited enhanced Li-ion storage capability and cyclability, demonstrating a specific capacity of 400 mAh g⁻¹ beyond 100 cycles.     

Li2ZnTi3O8 nanorods: A new anode material for lithium-ion battery

Spinel Li₂ZnTi₃O₈ nanorods were first synthesized using titanate nanowires as a precursor. The synthesized nanorods are highly crystalline and used as an anode material in a rechargeable Li-ion battery. A large capacity of 220 mA h g^? 1 was kept after 30 cycles at a current density of 0.1 A g^? 1, which is close to the theoretic capacity. The electrochemical measurements indicate that the anode material made of spinel Li₂ZnTi₃O₈ nanorods displayed a highly reversible capacity and excellent cycling stability.     

Synthesis and characterization of nanocrystalline tin oxide by sol–gel method

Nanocrystalline SnO₂ particles have been synthesized by a sol–gel method from the very simple starting material granulated tin. The synthesis leads a sol–gel process when citric acid is introduced in the solution obtained by dissolving granulated tin in HNO₃. Citric acid has a great effect on stabilizing the precursor solution, and slows down the hydrolysis and condensation processes. The obtained SnO₂ particles range from 2.8 to 5.1 nm in size and 289–143 m² g⁻¹ in specific surface area when the gel is heat treated at different temperatures. The particles show a lattice expansion with the reduction in particle size. With the absence of citric acid, the precursor hydrolyzes and condenses in an uncontrollable manner and the obtained SnO₂ nanocrystallites are comparatively larger in size and broader in size distribution. The nanocrystallites have been characterized by means of TG-DSC, FT-IR, XRD, BET and TEM.     

SnO2 meso-scale tubes: One-step,room temperature electrodeposition synthesis and kinetic investigation for lithium storage

SnO₂ meso-scale tubes were synthesized by anodic electrochemical deposition under ambient conditions. Controlled self-bubbling O₂ acted as both the template and the oxidizing agent for obtaining SnO₂ tube structures at the interface of the gas (O₂) and the liquid (electrolyte). Electrochemical testing showed that the meso-scale tubes have higher discharge capacity and better rate capability than the “microbowls” produced by varying the deposition conditions. From the Arrhenius plot, the apparent activation energies were calculated to be 58.4 and 90.1 kJ mol^?1 for the meso-scale tubes and the microbowls, respectively, indicating that the meso-scale structure allows shorter diffusion routes for the lithium ions or for easier interaction with lithium.     

Fe-doped SnO2 transparent semi-conducting thin films deposited by spray pyrolysis technique: Thermoelectric and p-type conductivity properties

In this paper, we report structural, electrical, optical, and especially thermoelectrical characterization of iron (Fe) doped tin oxide films, which have been deposited by spray pyrolysis technique. The doping level has changed from 0 to 10 wt% in solution ([Fe]/[Sn] = 0–40 at% in solution). The thermoelectric response versus temperature difference has exhibited a nonlinear behavior, and the Seebeck coefficient has been calculated from its slope in temperature range of 300–500 K. The Hall effect and thermoelectric measurements have shown p-type conductivity in SnO₂:Fe films with [Fe]/[Sn] ≥ 7.8 at%. In doping levels lower than 7.8 at%, SnO₂:Fe films have been n-type with a negative thermoelectric coefficient. The Seebeck coefficient for SnO₂:Fe films with 7.8 at% doping level has been obtained to be as high as +1850 μV/K. The analysis of as-deposited samples with thicknesses ～350 nm by X-ray diffraction (XRD) and scanning electron microscopy (SEM) has shown polycrystalline structure with clear characteristic peak of SnO₂ cassiterite phase in all films. The optical transparency (T%) of SnO₂:Fe films in visible spectra decreases from 90% to 75% and electrical resistivity (ρ) increases from 1.2 × 10^?2 to 3 × 10³ Ω cm for Fe-doping in the range 0–40 at%.     

Synthesis,characterization and electrocatalytic activity for ethanol oxidation of carbon supported Pt,Pt–Rh,Pt–SnO2 and Pt–Rh–SnO2 nanoclusters

Nanoclusters of Pt, Pt–Rh, Pt–SnO₂ and Pt–Rh–SnO₂ were successfully synthesized by polyol method and deposited on high-area carbon. HRTEM and XRD analysis revealed two phases in the ternary Pt–Rh–SnO₂/C catalyst: solid solution of Rh in Pt and SnO₂. The activity of Pt–Rh–SnO₂/C for ethanol oxidation was found to be much higher than Pt/C and Pt–Rh/C and also superior to Pt–SnO₂/C. Quasi steady-state measurements at various temperatures (30–60 °C), ethanol concentrations (0.01–1 M) and H₂SO₄ concentrations (0.02–0.5 M) showed that Pt–Rh–SnO₂/C is about 20 times more active than Pt/C in the potential range of interest for the fuel cell application.     

Photovoltaic characteristics of dye-sensitized surface-modified nanocrystalline SnO2 solar cells

Zinc-modified nanocrystalline SnO₂ electrodes are prepared by chemical treatment of the commercial SnO₂ colloid with zinc acetate and their thickness effects on photovoltaic characteristics are investigated. Open-circuit voltage (V_oc) and fill factor increase with increasing zinc concentration, while short-circuit photocurrent (J_sc) decreases. The normalized incident photon-to-current conversion efficiency (IPCE) shows that increase of zinc concentration utilizes long wavelength light. Concerning the conversion efficiency, optimal concentration within the present experiment is found to be 10 mol.% Zn²⁺ with respect to Sn⁴⁺. As increasing thickness of the films based on 10 mol.% zinc-modified SnO₂ ranging from 0.76 to 8.12 μm, J_sc increases, reaches maximum and then decreases without change in V_oc. The highest conversion efficiency of about 3.4% is achieved under 1 sun of AM 1.5 irradiation for the ∼6.3 μm-thick 10 mol.% zinc-modified SnO₂ film with J_sc of 9.09 mA/cm², V_oc 600 mV and fill factor 62%.     

A novel process to prepare porous membranes comprising SnO2 nanoparticles and P(MMA-AN) as polymer electrolyte

We have successfully developed a new process to prepare porous poly(methyl methacrylate-co-acrylonitrile) (P(MMA-AN)) copolymer based gel electrolyte. The porous structure in the polymer matrix is achieved by adding SnO₂ nanoparticles which are mostly used as gas sensor materials. The quasi-aromatic solvent, NMP, has an electron-repulsion effect with the space charge layer on the surface of SnO₂ nanoparticles and forms a special gas–liquid phase interface. Once the cast polymer solution is stored at an elevated temperature to evaporate the solvent, gas–liquid phase separation happens and spherical pores are obtained. The ionic conductivity at room temperature of the prepared gel polymer electrolyte based on the porous membrane is as high as 1.54 × 10⁻³ S cm⁻¹ with the electrochemical stability up to 5.10 V (vs. Li/Li⁺). This method presents another promising way to prepare porous polymer electrolyte for practical use.     

Novel poly (neutral red) nanowires as a sensitive electrochemical biosensing platform for hydrogen peroxide determination

Poly (neutral red) nanowires (PNRNWs) have been synthesized for the first time by the method of cyclic voltammetric electrodeposition using porous anodic aluminum oxide (AAO) template and were examined by scanning electron microscopy (SEM) and transmission electron microscope (TEM). Moreover, horseradish peroxidase (HRP) was encapsulated in situ in PNRNWs (denoted as PNRNWs–HRP) by electrochemical copolymerization for potential biosensor applications. The PNRNWs showed excellent efficiency of electron transfer between the HRP and the glassy carbon (GC) electrode for the reduction of H₂O₂ and the PNRNWs–HRP modified GC electrode showed to be excellent amperometric sensors for H₂O₂ at −0.1 V with a linear response range of 1 μM to 8 mM with a correlation coefficient of 0.996. The detection limit (S/N = 3) and the response time were determined to be 1 μM and <5 s and the high sensitivity is up to 318 μA mM⁻¹ cm⁻².     

Catalytic vapor-phase oxidation of 2,2,2-trifluoroethanol

The synthesis of trifluoroacetaldehyde by vapor-phase oxidation of 2,2,2-trifluoroethanol using supported vanadium catalysts was studied. Significant differences were observed in the reaction outcomes resulting from different types of catalysts. The ZrO₂- and Al₂O₃-supported catalyst demonstrated both high catalytic activity and selectivity. The addition of co-catalysts such as MoO₃ or SnO₂ improved catalytic performance (Selectivity: up to 91%; S.T.Y.: >200 g L⁻¹ h⁻¹). The experimental results on catalyst lifetime showed a marked decrease in the activity of the Al₂O₃-supported catalyst within tens of hours, while the ZrO₂-supported catalyst showed little, if any, performance alterations for 2000 h.     

Study of CuZnMOx oxides (M = Al,Zr, Ce,CeZr) for the catalytic hydrogenation of CO2 into methanol

CuO–ZnO–Al₂O₃ catalysts were synthesized by two methods, sol–gel and co-precipitation syntheses. Al₂O₃ was then substituted with other supports, such as ZrO₂, CeO₂ and CeO₂–ZrO₂ in order to have a better understanding of the support's effect. These catalysts containing 30 wt% of Cu were then tested for CO₂ hydrogenation into methanol. The effect of reaction temperature and GHSV on the catalytic behaviour was also investigated. The best results were obtained with a 30 CuO–ZnO–ZrO₂ catalyst synthesized by co-precipitation and calcined at 400 °C. This catalyst presents a good CO₂ conversion rate (23%) with 33% of methanol selectivity, leading to a methanol productivity of 331 g_MeOH.kg_cata⁻¹·h⁻¹ at 280 °C under 50 bar and a GHSV of 10,000 h⁻¹.     

Theoretical study on the stability and electronic property of Ag2SnO3

Bulk crystal properties of Ag₂SnO₃ were investigated with the advantage of density functional theory. The whole structure has layered feature: hexagonal metallic planes formed by Ag atoms and distorted octahedrons of SnO₆ clusters are configured alternatively along c axis of hexagonal cell. The cohesive energy is about ?2.792 eV/atom, which is less than SnO₂. The Debye temperature of Ag₂SnO₃ is about 231.6 K, and the bulk and shear moduli are 62.13 and 20.63 GPa, respectively. Band structure and DOS show the compound has a small pseudo-band gap value of 1.0 eV and so may be a semiconductor. When checking the PDOS intensity at the Fermi surface of Ag atoms, a weak metallic character can be seen. The distortion mechanism becomes less effective to reduce the total orbital energy both in SnO₂ and in Ag₂SnO₃ and as a result the bond lengths of Sn–O are intended to be isotropy.     

High capacity and excellent cyclability of vanadium (IV) oxide in lithium battery applications

A VO₂ · 0.43H₂O powder with a flaky particle morphology was synthesized via a hydrothermal reduction method. It was characterized by scanning electron microscopy, electron energy loss spectroscopy, and thermogravimetric analysis. As an electrode material for rechargeable lithium batteries, it was used both as a cathode versus lithium anode and as an anode versus LiCoO₂, LiFePO₄ or LiNi_0.5Mn_1.5O₄ cathode. The VO₂ · 0.43H₂O electrode exhibits an extraordinary superiority with high capacity (160 mAh g^?1), high energy efficiency (95%), excellent cyclability (142.5 mAh g^?1 after 500 cycles) and rate capability (100 mAh g^?1 at 10 C-rate).     

Electrochemical properties of Li(Li(1−x)/3CoxMn(2−2x)/3)O2 (0 ⩽ x ⩽ 1) solid solutions prepared by poly-vinyl alcohol (PVA) method

The whole range of solid solutions Li(Li_(1−x)/3Co_xMn_(2−2x)/3)O₂ (0 ⩽ x ⩽ 1) was firstly synthesized by an aqueous solution method using poly-vinyl alcohol as a synthetic agent to investigate their structure and electrochemical properties. X-ray diffraction results indicated that the synthesized solid solutions showed a single phase without any detectable impurity phase and have a hexagonal structure with some additional peaks caused by monoclinic distortion, especially in the solid solutions with a low Co amount. In the electrochemical examination, the solid solutions in the range between 0.2 ⩽ x ⩽ 0.9 showed higher discharge capacity and better cyclability than LiCoO₂ (x = 1) on cycling between 2.0 and 4.6 V with 100 mA g⁻¹ at 25 °C. For example, Li(Li_0.2Co_0.4Mn_0.4)O₂ (x = 0.4) exhibited a high discharge capacity of 180 mA h g⁻¹ at the 50th cycle. By synthesizing the solid solution between Li₂MnO₃ and LiCoO₂, the electrochemical properties of the end members were improved.