Enhanced performance of bi-layer Nb2O5 coated TiO2 nanoparticles/nanowires composite photoanode in dye-sensitized solar cells

Dye sensitized solar cells (DSSCs) were fabricated based on coumarin NKX-2700 dye sensitized bi-layer photoanode and quasi-solid state electrolyte sandwiched together with cobalt sulfide coated counter electrode. A novel bi-layer photoanode has been prepared using composite mixtures of 90 wt.% TiO₂ nanoparticles + 10 wt.% TiO₂ nanowires (TNPWs) as active layer and Nb₂O₅ is coated on the active layer, which acts as scattering layer. Hafnium oxide (HfO₂) was applied over the TNPWs/Nb₂O₅ photoanode film, as a blocking layer. TiO₂ nanoparticles (TNPs), TiO₂ nanowires (TNWs) and TNPWs/Nb₂O₅ were characterized by X-ray diffractometer (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM). The sensitizing organic dye coumarin NKX-2700 displayed maximum absorption wavelength (λ_max) at 525 nm, which could be observed from the UV–vis spectrum. DSSC-1 fabricated with composite bi-layer photoanode revealed enhanced photo-current efficiency (PCE) as compared to other DSSCs and illustrated photovoltaic parameters; short-circuit current J_SC = 18 mA/cm², open circuit voltage (V_OC) = 700 mV, fill factor (FF) = 64% and PCE (η) = 8.06%. The electron transport and charge recombination behaviors of DSSCs were investigated by electrochemical impedance spectra (EIS) and the results illustrated that the DSSC-1 showed the lowest charge transport resistance (R_tr) and the longest electron lifetime (τ_eff). Therefore, in the present investigation, it could be concluded that the novel bi-layer photoanode with blocking layer increased the short circuit current, electron transport and suppressed the recombination of charge carriers at the photoanode/dye/electrolyte interface in DSSC-1.     

Effect of Sn doping on the structural,optical and electrical properties of TiO2 films prepared by spray pyrolysis

In this work, highly oriented pure and Tin-doped Titanium dioxide (Sn-doped TiO₂) with porous nature photoelectrodes were deposited on ITO glass plates using spray pyrolysis technique. The XRD pattern revealed the formation of anatase TiO₂ with the maximum intensity of (101) plane while doping 6 at% of Sn. The morphological studies depicted the porous nature with the uniform arrangement of small-sized grains. The presence of tin confirmed with the EDX spectra. The size of particles of 13 nm was observed from High Resolution Transmission Electron Microscopy (HR-TEM) analysis. The average transmittance was about 85% for the doped photoelectrode and was observed for the photoelectrode deposited with 6 at% of tin, with decreased energy band gap. The PL study showed the emission peak at 391 nm. The maximum carrier concentration and Hall mobility was observed for the photoelectrode deposited with 6 at% of tin. With these studies, the DSSCs were prepared separately with the dye extracted from Hibiscus Rosasinesis and Hibiscus Surttasinesis and their efficiency was maximum for the DSSC prepared with 6 at% of tin.     

Current transport mechanism and photovoltaic properties of photoelectrochemical cells of ITO/TiO2/PVC–LiClO4/graphite

This paper deals with the current transport mechanism of solid state photoelectrochemical cells of ITO/TiO₂/PVC–LiClO₄/graphite as well as the physical properties of a component of a device affecting its performance. The principle of operation and a schematic energy level diagram for the materials used in the photoelectrochemical cells are presented. The device makes use of ITO films, TiO₂ films, PVC–LiClO₄ and graphite films as photoanode, photovoltaic material, solid electrolyte and counter electrode, respectively. The device shows rectification. The J_sc and V_oc obtained at 100 mW cm⁻² were 0.95 μAcm⁻² and 180 mV, respectively.     

Preparation and photocatalytic degradation of erbium doped titanium dioxide nanorods

Photocatalytic degradation of methylene blue (MB) in water was examined using Er³⁺-doped TiO₂ (Er–TiO₂) nanorods prepared by a sol–gel derived electrospinning, calcination, and subsequent mechanical grinding. Different concentrations of Er dopant in the range of 0–1.0 mol% were synthesized to evaluate the effect of Er content on the photocatalytic activity of TiO₂. Among Er³⁺–TiO₂ catalysts, the 0.7 mol% Er³⁺–TiO₂ catalyst showed the highest MB degradation rate. The degradation kinetic constant (k) increased from 1.0 × 10^?3 min^?1 to 5.1 × 10^?3 min^?1 with the increase of Er³⁺ doping from 0 to 0.7 mol%, but decreased down to 2.1 × 10^?3 min^?1 when Er³⁺ content was 1.0 mol%. It can be concluded that the degradation of MB under UV radiation was more efficient with Er³⁺–TiO₂ catalyst than with pure TiO₂. The higher activity might be attributed to the transition of 4f electrons of Er³⁺ and red shifts of the optical absorption edge of TiO₂ by erbium ion doping.     

Preparation of silver nanowires coated with TiO2 using chemical binder and their applications as photoanodes in dye sensitized solar cell

In this study, the core–shell structured Ag@TiO₂ wire was prepared for application to dye-sensitized solar cell (DSSC). The Ag nanowire, having an excellent electrical conductivity, was synthesized by using the facile microwave-assisted polyol reduction process. The diameter and length of Ag wires were 40–50 nm and 20–30 μm, respectively, and the face-centered cubic silver crystal structure was obtained. In the presence of 2-mercaptoethanol as a chemical binder, the entire surface of Ag wire was coated with the TiO₂ shell, which has thickness of 20 nm, through solvothermal method. The crystalline structure of TiO₂ shell was the anatase phase possessing an advantage to achieve the high efficiency in DSSC. The core–shell structured Ag@TiO₂ wire exhibited the high thermal stability. The high conversion efficiency (5.56%) in fabricated device with Ag@TiO₂ electrode, which is about 10% higher than reference cell, was achieved by enhancement of short-current density (J_sc) value. The core–shell structured Ag@TiO₂ wire could effectively reduce the charge recombination through the contribution to electron shortcut for improvement in the electron transfer rate and lifetime.     

Effect of Ti4+ ions doping on microstructure and dc resistivity of nickel ferrites

Nanostructured nickel ferrites (NiFe₂O₄) were prepared by doping with Ti⁴⁺ ions using solid-state reaction route. Lowest grain size of 55 nm was achieved in the specimens with 20 mole% TiO₂ doping. Magnetization in the specimens decreases with decreasing grain sizes. Lower volume fractions of ferrite phase due to dissociation of the magnetic phase into smaller particles by the disruption of super exchange interaction by the titanium substitution results a decrease in magnetizations. Coercivity showed an increasing trend. This was explained as arising due to multidomain/monodomain magnetic behavior of magnetic nanoparticles. Small polaron hopping conduction between Fe²⁺ and Fe³⁺ sites controls the dc electrical properties of the specimens. The presence of an interfacial amorphous phase between the sites is evident from Mott's analysis. Specimens containing 10 mole or more TiO₂ and sintered at 1350 °C contain NiTiO₃ as a secondary phase and show unusual dc conductivity.     

Acoustic and optical phonons in EVOH–TiO2 nanocomposite films: Effect of aggregation

Films of an organic–inorganic nanocomposite material formed by a polymeric matrix (ethylene–vinyl alcohol copolymer—EVOH) and nanometric TiO₂ particles (ca. 10 nm) have been obtained with photo-catalytic properties in the elimination of pathogens. Optical spectroscopy experiments have been performed in order to characterize the films and evaluate their properties as a function of TiO₂ doping in the range between 0.25 and 13 wt%. Anatase TiO₂ nanoparticles seem to be well-dispersed up to 2% but aggregation for higher doping originates the two different regimes observed in the acoustic modes as well as in the optical absorption in the visible spectral range.     

Fabrication of Fe-doped TiO2 nanoparticles and investigation of photocatalytic decolorization of reactive red 198 under visible light irradiation

In this research, Fe-doped TiO₂ nanoparticles with various Fe concentrations (0. 0.1, 1, 5 and 10 wt%) were prepared by a sol–gel method. Then, nanoparticles were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray analysis (EDX), BET surface area, photoluminescence (PL) spectroscopy and UV–vis diffuse reflectance spectroscopy (DRS). The photocatalytic activity of the nano-particles was evaluated through degradation of reactive red 198 (RR 198) under UV and visible light irradiations. XRD results revealed that all samples contained only anatase phase. DRS showed that the Fe doping in the titania induced a significant red shift of the absorption edge and then the band gap energy decreased from 3 to 2.1 eV. Photocatalytic results indicated that TiO₂ had a highest photocatalytic decolorization of the RR 198 under UV irradiation whereas photocatalytic decolorization of the RR 198 under visible irradiation increased in the presence of Fe-doped TiO₂ nanoparticles. Among the samples, Fe-1 wt% doped TiO₂ nanoparticles showed the highest photocatalytic decolorization of RR198 under visible light irradiation.     

Development of the IR laser pyrolysis for the synthesis of iron–doped TiO2 nanoparticles: Structural properties and photoactivity

The preparation of TiO₂-based nanoparticles of closely controlled sizes and purity gives rise to considerable interest in the frame of environmental applications, e.g. in photocatalysis. When nanoparticles instead of their bulk counterpart are used the synthesis method plays a fundamental role in defining specific structural properties. Between the different gas-phase synthesis techniques, the CO₂ laser pyrolysis is a versatile method allowing for the preparation of nanostructures of various chemical compositions. Here we demonstrate that pure and Fe–doped TiO₂ nanoparticles with rather low Fe concentration may be prepared by applying the sensitized IR laser pyrolysis to a gas mixtures containing titanium tetrachloride, air and iron pentacarbonyl (vapors). The structures of TiO₂-based particles were systematically investigated by X-ray diffraction, transmission electron microscopy, high-resolution electron microscopy, selected area electron diffraction and X-ray Photoelectron Spectroscopy. Depending on the synthesis parameters, the nanoparticle system contains mixtures of anatase and rutile, with a preponderance of the anatase phase. Higher rutile proportion was found in the iron-doped samples. Mean particle diameters of around 14 nm and 12 nm were estimated for undoped and doped anatase titania, respectively. From UV–Vis diffuse reflectance spectra, higher absorbance and red shifted absorption were evidenced at higher amount of doped iron. Preliminary evaluation tests of the UV photoactivity of samples were performed by using the scanning electrochemical microscopy for determining the evolution of the oxygen consumption in the presence of IV-chlorophenol. They show that the undoped nano titania samples perform better than the reference P25 Degussa sample. A drop of the nano-titania photoactivity as a consequence of Fe doping was observed. Possible reasons of this effect are tentatively discussed.     

The improvement of pyroelectric properties of PZT thick films on Si substrate by TiOx barrier layer

The effects of TiO_x diffusion barrier layer thickness on the microstructure and pyroelectric characteristics of PZT thick films were studied in this paper. The TiO_x layer was prepared by thermal oxidation of Ti thin film in air and the PZT thick films were fabricated by electrophoresis deposition method (EPD). To demonstrate the barrier effect of TiO_x layer, the electrode/substrate interface and Si content in PZT thick films were characterized by scanning electron microscope (SEM) and X-ray energy dispersive spectroscopy (EDS), respectively. The TiO_x barrier thickness shows significant influence on the bottom electrode and the pyroelectric performance of the PZT thick films. The average pyroelectric coefficient of PZT films deposited on 400 nm TiO_x layer was about 8.94 × 10⁻⁹ C/(cm² K), which was improved by 70% than those without diffusion barrier layer. The results showed in this study indicate that TiO_x barrier layer has great potential in fabrication of PZT pyroelectric device.     

Synthesis of TiO2/WO3 nanoparticles via sonochemical approach for the photocatalytic degradation of methylene blue under visible light illumination

Through an ultrasound assisted method, TiO₂/WO₃ nanoparticles were synthesized at room temperature. The XRD pattern of as-prepared TiO₂/WO₃ nanoparticles matches well with that of pure monoclinic WO₃ and rutile TiO₂ nanoparticles. TEM images show that the prepared TiO₂/WO₃ nanoparticles consist of mixed square and hexagonal shape particles about 8–12 nm in diameter. The photocatalytic activity of TiO₂/WO₃ nanoparticles was tested for the degradation of a wastewater containing methylene blue (MB) under visible light illumination. The TiO₂/WO₃ nanoparticles exhibits a higher degradation rate constant (6.72 × 10⁻⁴ s⁻¹) than bare TiO₂ nanoparticles (1.72 × 10⁻⁴ s⁻¹) under similar experimental conditions.     

Preparation of (5.0%)Er3+:Y3Al5O12/Pt-(TiO2-Ta2O5) nanocatalysts and application in sonocatalytic decomposition of ametryn in aqueous solution

(5.0%)Er³⁺:Y₃Al₅O₁₂/Pt-(TiO₂-Ta₂O₅) powder, as a high effective sonocatalyst, was prepared using sol-gel and calcination method. Then it was characterized by X-ray diffractometer (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDX). In order to evaluate the sonocatalytic activity of the prepared (5.0%)Er³⁺:Y₃Al₅O₁₂/Pt-(TiO₂-Ta₂O₅) powder, the sonocatalytic decomposition of ametryn was studied. In addition, some influencing factors such as different Ti/Ta molar ratios on the sonocatalytic activity of the prepared (5.0%)Er³⁺:Y₃Al₅O₁₂/Pt-(TiO₂-Ta₂O₅) powder, catalyst added amount with ultrasonic irradiation time and used times on the sonocatalytic decomposition efficiency were examined by using ion chromatogram determination. The experimental results showed that the best sonocatalytic decomposition ratio of ametryn were 77.50% based on the N atom calculation and 95.00% based on the S atom calculation, respectively, when the conditions of 10.00 mg/L initial concentration, 1.00 g/L prepared (5.0%)Er³⁺:Y₃Al₅O₁₂/Pt-(TiO₂-Ta₂O₅) powder (Ti/Ta = 1.00:0.25 heat-treated at 550 °C for 3.0 h) added amount, 150 min ultrasonic irradiation (40 kHz frequency and 300 W output power), 100 mL total volume and 25–28 °C temperature were adopted. Therefore, the (5.0%)Er³⁺:Y₃Al₅O₁₂/Pt-(TiO₂-Ta₂O₅) composite nanoparticles could be considered as an effective sonocatalyst for decomposition of ametryn in aqueous solution.     

Ultrasonic synthesis and photocatalytic characterization of H3PW12O40/TiO2 (anatase)

A novel H₃PW₁₂O₄₀/TiO₂ (anatase) composite photocatalyst was prepared by a high-intensity ultrasonic method using a lower temperature (80 °C) and was characterized by XRD and FT-IR. Its photocatalytic activity, using solar light, was evaluated through the degradation of organic dye methylene blue (MB) in aqueous. When MB solution (50 mg/l, 200 ml) containing H₃PW₁₂O₄₀/TiO₂ (anatase) (0.4 g) was degraded by solar irradiation after 90 min, the removal of concentration and TOC of MB reached 95% and 73%, respectively. The photocatalyst activity of H₃PW₁₂O₄₀/TiO₂ (anatase) was much higher than TiO₂ which was prepared in the same way. H₃PW₁₂O₄₀/TiO₂ remained efficient after five repeated experiments.     

Sonocatalytic degradation of organic dyes and comparison of catalytic activities of CeO2/TiO2, SnO2/TiO2 and ZrO2/TiO2 composites under ultrasonic irradiation

The CeO₂/TiO₂, SnO₂/TiO₂ and ZrO₂/TiO₂ composites were prepared by dispersing various nano-sized oxides (CeO₂, SnO₂, ZrO₂ and TiO₂) with ultrasound and mixing TiO₂ with CeO₂, SnO₂ and ZrO₂, respectively, in boiling water in a molar ratio of 4:1, followed by calcining temperature 500 °C for 60 min. Then a series of sonocatalytic degradation experiments were carried out under ultrasonic irradiation in the presence of CeO₂/TiO₂, SnO₂/TiO₂ and ZrO₂/TiO₂ composites and nano-sized TiO₂ powder. Also, the influences of heat-treatment temperature and heat-treatment time on the sonocatalytic activities of CeO₂/TiO₂, SnO₂/TiO₂ and ZrO₂/TiO₂ composites, and of irradiation time and solution acidity on the sonocatalytic degradation of Acid Red B were investigated by UV–vis spectra. It was found that the sonocatalytic degradation of Acid Red B shows significant variation in rate and ratio that decreases in order: CeO₂/TiO₂ > SnO₂/TiO₂ > TiO₂ > ZrO₂/TiO₂ > SnO₂ > CeO₂ > ZrO₂, and the corresponding ratios of Acid Red B in aqueous solution are 91.32%, 67.41%, 65.26%, 41.67%, 28.34%, 26.75% and 23.33%, respectively. And that the degradation ratio is only 16.67% under onefold ultrasonic irradiation. Because of the good degradation efficiency, this method may be an advisable choice for the treatment of non- or low-transparent wastewaters in the future.     

Cu-doped flower-like hematite nanostructures for efficient water splitting applications

This study reports the successful preparation of Cu-doped hematite (α-Fe₂O₃) flower-like nanostructures with different Cu concentrations on FTO glass substrates using a facile hydrothermal method. The Cu-doped α-Fe₂O₃ flower-like nanostructure combines the advantage of p-type doping with the feature of a flower-like architecture. The prepared nanostructure film was applied as a photocathode in a photoelectrochemical (PEC) water splitting experiment and achieved a significantly improved photocurrent density of −5.34 mA cm⁻² at −0.6 V vs. reversible hydrogen electrode (RHE) for 1 mol% Cu doping. The obtained photocurrent is about 4.85 times higher than that of the pure α-Fe₂O₃ based photoelectrode. The incorporation of Cu into α-Fe₂O₃ results in a dramatic enhancement in the water splitting performance. The enhancement is gained through an improvement in light harvesting and charge carrier separation. The copper-modified α-Fe₂O₃ sample also exhibited an up shift in the conduction band edge potential, which is energetically favorable for the water reduction reaction. This result demonstrated high performance PEC water splitting as a potential route for the production of hydrogen gas using a single Cu-doped α-Fe₂O₃ photoelectrode without the need for other catalysts and hybrid structures.     

Acute effects of sono-activated photocatalytic titanium dioxide nanoparticles on oral squamous cell carcinoma

Sonodynamic therapy (SDT) is a new treatment modality using ultrasound to activate certain chemical sensitizers for cancer therapy. In this study, effects of high intensity focused ultrasound (HIFU) combined with photocatalytic titanium dioxide (TiO₂) nanoparticles on human oral squamous cell line HSC-2 were investigated. Viability of HSC-2 cells after 0, 0.1, 1, or 3 s of HIFU irradiation with 20, 32, 55 and 73 W cm⁻² intensities in the presence or absence of TiO₂ was measured immediately after the exposures in vitro. Immediate effects of HIFU (3 s, 73 W cm⁻²) combined with TiO₂ on solid tumors were also examined by histological study. Cytotoxic effect of HIFU + TiO₂ in vitro was significantly higher than that of TiO₂ or HIFU alone with the tendency to increase for higher HIFU intensity, duration, and TiO₂ concentration in the suspension. In vivo results showed significant necrosis and tissue damage in HIFU and HIFU + TiO₂ treated samples. However, penetration of TiO₂ nanoparticles into the cell cytoplasm was only observed in HIFU + TiO₂ treated tissues. In this study, our findings provide a rational basis for the development of an effective HIFU based sonodynamic activation method. This approach offers an attractive non-invasive therapy technique for oral cancer in future.     

TiO2(110)-(1 × 1) supported Cu particles: An FT-RAIRS investigation

The morphology of TiO₂(110)-(1 × 1) supported Cu particles has been investigated by Fourier Transform Reflection Absorption Infrared Spectroscopy (FT-RAIRS), employing adsorbed CO as a probe molecule sensitive to local surface structure. For Cu coverage (deposited at 300 K) less than 2.85 MLE nucleated Cu particles in the range 2 nm–4 nm are formed, as indicated by a final state shift in the core level Cu(2p_3/2) binding energy and by the existence of only transmission bands in the FT-RAIRS spectra for adsorbed CO. ν_S(CO) indicates that these small particles expose sites similar to those of the stepped Cu surfaces Cu(211), Cu(311), and Cu(755). At Cu coverages in the range of 6 MLE and above, corresponding to particle sizes above 4.6 nm, ν_S(CO) indicates the predominance of (110), (100) and (111) adsorption sites. Annealing the Cu layers to 650 K results in the slight growth of the particle sizes, and transformation of the CO adsorption sites corresponding to the close packed facets. The transformation of the local dielectric from that of titania to that dominated by the Cu particle is shown to take place between 3.7 and 4.2 nm, and this change is also to a smaller extent sensitive to the dispersion of the particles.     

Ultrasound assisted synthesis of TiO2–WO3 heterostructures for the catalytic degradation of Tergitol (NP-9) in water

TiO₂–WO₃ heterostructures were synthesized at room temperature, ambient pressure, and short reaction time via a sonochemical approach. TEM and EDX images show that the prepared TiO₂–WO₃ heterostructures consist of globular agglomerates (∼250 nm in diameter) composed of very small (<5 nm) dense particles (WO₃) dispersed inside the globules. The observed less intense monoclinic WO₃ diffraction peak (around 2θ = 22° belonging to (0 0 1) plane) and the high intense hexagonal WO₃ diffraction peak (around 2θ = 28° belonging to (2 0 0) plane) in XRD indicate that there may be phase transition occurring due to the formation of intimate bond between TiO₂ and WO₃. In addition, the formation of such new phase was also observed from Raman spectra with a new peak at 955 cm⁻¹, which is due to the symmetric stretching of W = O terminal. The catalytic activity of TiO₂–WO₃ heterostructures was tested for the degradation of wastewater pollutant containing Tergitol (NP-9) by a process combined with ozonation and it showed two-fold degradation rate compared with ozone process alone.     

Effect of nanosize titanium oxide on electrochemical characteristics of activated carbon electrodes

Energy-storage composite electrodes were prepared by mixing activated carbons (ACs) modified with nanosize titanium oxide (TiO₂) through ultrasonic vibration in ethanol solution for 30 min. We examined the cyclic voltammetry of the composite electrodes in an aqueous electrolyte, 1 M H₂SO₄. It was found that the specific capacitance of the composite electrodes measured in a range of 0–0.8 V was increased from 100 to 155 F/g compared electrodes comprised of ACs only. This was attributed to a reduction of polarization of the ACs modified by nanosized TiO₂.     

AZO/Ag/AZO multilayer films prepared by DC magnetron sputtering for dye-sensitized solar cell application

Ag films were deposited on Al-doped ZnO (AZO) films and coated with AZO to fabricate AZO/Ag/AZO multilayer films by DC magnetron sputtering on glass substrates without heating of glass substrates. The best multilayer films have low sheet resistance of 19.8 Ω/Sq and average transmittance values of 61% in visible region. It was found that the highest figure of merit (F_TC) is 6.9 × 10⁻⁴ Ω⁻¹. For the dye-sensitized solar cell (DSSC) application, the multilayer films were used as transparent conductive electrode (multilayer films/ZnO + Eosin-Y/LiI + I₂/Pt/FTO). The best DSSC based on the multilayer films showed that open circuit voltage (V_oc) of 0.47 V, short circuit current density (J_sc) of 2.24 mA/cm², fill factor (FF) of 0.58 and incident photon-to-current conversion efficiency (η) of 0.61%. It was shown that the AZO/Ag/AZO multilayer films have potential for application in DSSC.