Effect of backbone flexibility on charge transfer rates in peptide nucleic acid duplexes

Charge transfer (CT) properties are compared between peptide nucleic acid structures with an aminoethylglycine backbone (aeg-PNA) and those with a γ-methylated backbone (γ-PNA). The common aeg-PNA is an achiral molecule with a flexible structure, whereas γ-PNA is a chiral molecule with a significantly more rigid structure than aeg-PNA. Electrochemical measurements show that the CT rate constant through an aeg-PNA bridging unit is twice the CT rate constant through a γ-PNA bridging unit. Theoretical calculations of PNA electronic properties, which are based on a molecular dynamics structural ensemble, reveal that the difference in the CT rate constant results from the difference in the extent of backbone fluctuations of aeg- and γ-PNA. In particular, fluctuations of the backbone affect the local electric field that broadens the energy levels of the PNA nucleobases. The greater flexibility of the aeg-PNA gives rise to more broadening, and a more frequent appearance of high-CT rate conformations than in γ-PNA.     

A double-stranded molecular probe for homogeneous nucleic acid analysis

This paper reports the design and optimization of a double-stranded molecular probe for homogeneous detection of specific nucleotide sequences. The probes are labeled with either a fluorophore or a quencher such that the probe hybridization brings the two labels into close proximity, and this diminishes the fluorescence signal in the absence of a target. In the presence of a target, the fluorophore probe is thermodynamically driven to unzip from its hybridized form and bind with the target. An equilibrium analysis, which successfully describes all the major features of the assay without any fitting parameter, is performed to generalize the design of the probe. Several key parameters affecting the performance of the assay are examined. We show that the dynamic range and the signal-to-noise ratio of the assay can be optimized by the probe concentration, the quencher-to-fluorophore ratio, and the probe strand sequence. By proper design of the sequence, the probe discriminates single nucleotide mismatches in a single step without any separation step or measurement of melting profile.     

Surface-hopping model for near-resonant electronic energy transfer

A surface-hopping model is applied to near-resonant electronic energy transfer in the NFBi and O₂I systems. Multiple surface crossings occur in NFBi at ca. 8 A, corresponding well with measured transfer cross section of 200 A². A Landau-Zener model yields the temperature dependence of the thermally averaged cross section for the laser pumping reaction, O^*₂(a¹Δ) + I(²P_{$\text{3}\text{2}$}) → O₂(X³Σ^?_g) + 1^*(²P_{$\text{1}\text{2}$}).     

Metal-containing peptide nucleic acid conjugates

Peptide Nucleic Acids (PNAs) are non-natural DNA/RNA analogues with favourable physico-chemical properties and promising applications. Discovered nearly 20 years ago, PNAs have recently re-gained quite a lot of attention. In this Perspective article, we discuss the latest advances on the preparation and utilisation of PNA monomers and oligomers containing metal complexes. These metal- conjugates have found applications in various research fields such as in the sequence-specific detection of nucleic acids, in the hydrolysis of nucleic acids and peptides, as radioactive probes or as modulators of PNA·DNA hybrid stability, and last but not least as probes for molecular and cell biology.     

Charge transfer through modified peptide nucleic acids

We studied the charge transfer properties of bipyridine-modified peptide nucleic acid (PNA) in the absence and presence of Zn(II). Characterization of the PNA in solution showed that Zn(II) interacts with the bipyridine ligands, but the stability of the duplexes was not affected significantly by the binding of Zn(II). The charge transfer properties of these molecules were examined by electrochemistry for self-assembled monolayers of ferrocene-terminated PNAs and by conductive probe atomic force microscopy for cysteine-terminated PNAs. Both electrochemical and single molecular studies showed that the bipyridine modification and Zn(II) binding do not affect significantly the charge transfer of the PNA duplexes.     

The alpha-helical peptide nucleic acid concept: merger of peptide secondary structure and codified nucleic acid recognition

A novel platform for nucleic acid recognition that integrates the alpha-helix secondary structure of peptides with the codified base-pairing capability of nucleic acids is reported. The resulting alpha-helical peptide nucleic acids (alpha PNAs) are composed of a repeating tetrapeptidyl unit, aa(1)-aa(2)-aa(3)-Ser(B), where aa(1) through aa(3) represent generic ancillary amino acids and B = nucleobases linked to Ser via a methylene bridge. Effective syntheses of constituent Fmoc-protected nucleoamino acids (Fmoc-Ser(B)-OH, where B = thymine, cytosine, and uracil) are described along with a protocol for the solid-phase synthesis of 21mer alpha PNAs containing five such nucleobases. By varying the ancillary amino acids, two distinct classes of alpha PNAs were constructed, having a net charge of -1 or +6, respectively, at physiological pH. The modular nature of the alpha PNA platform was illustrated by the synthesis of symmetrical disulfide-bridged alpha PNA dimers containing 10 nucleobases. Hybridization of these alpha PNAs with ssDNA has been examined by thermal denaturation, gel electrophoresis, and circular dichroism (CD) and the data indicated that alpha PNA binds to ssDNA in a cooperative manner with high affinity and sequence specificity. In general, b2 alpha PNAs bind faster and more strongly with ssDNA than do the corresponding b1 alpha PNAs. Parallel alpha PNA-DNA complexes are more stable than their antiparallel counterparts. CD studies also revealed that the hybridization event involves the folding of both species into their helical conformations. Finally, NMR experiments provided conclusive evidence of Watson-Crick base pairing in alpha PNA-ssDNA hybrids.     

Azidopeptide nucleic acid. An alternative strategy for solid-phase peptide nucleic acid (PNA) synthesis

[reaction: see text] A practical and efficient method for PNA synthesis using an azide group to mask the N-terminus is reported. The deprotection was carried out in 5 min, while couplings were complete within 60 min. The near neutral conditions of the phosphine deprotection combined with the base-free coupling using hydroxybenzotriazole-activated monomers make this approach very mild.     

核酸前体及其修饰结构的电子转移机理研究

应用荧光淬灭和激光光解瞬态吸收光谱技术研究了一系列核酸前体(核酸碱基、核苷及其结构修饰物)、小牛胸腺ctDNA与各种荧光探针及蛋白酶之间的瞬态、稳态电子转移作用机理。测定结果表明,它们的稳态、静态荧光淬灭作用很强,很好地符合Stern-Volmer线性方程,淬灭速率常数,k~q(s)和k~q(d),达10^10.M^-^1S^-^1,属于扩散控制,表明核酸前体的基态可作为电子受体或给体而分别与含色氨酸残基的蛋白酶、受电子型荧光探针之间发生具有电子转移性质的相互作用。对鸟嘌呤的结构修饰物进行了激光光解的瞬态吸收光谱研究,检测了几类活性中间体,论证了激发态的光致电子转移和能量转移机理。     

New synthesis of a spin-labeled peptide nucleic acid and its interactions with nucleic acids

A new combined solid-liquid phase synthesis method for a spin labeled peptide nucleic acid (PNA) is developed. The methodology involved initial preparation of a protected PNA on solid phase, followed by efficient solution phase coupling to a spin label containing a reactive carboxylic group. This strategy allows to maintain the integrity of the nitroxide moiety during the various steps of chemical synthesis assuring in the same time the fidelity of the hybridization assay. This compound can be used as a reporter molecule to investigate the binding of peptide nucleic acids to oligonucleotide sequences (DNA or RNA) by EPR spectroscopy.     

Peptide nucleic acid and amino acid modified peptide nucleic acid analysis by capillary zone electrophoresis

A rapid, high resolution, and low sample consumption CZE method is developed for peptide nucleic acid (PNA) analysis for the first time. 30% v/v acetonitrile in PNA sample and 20% v/v acetonitrile in 50 mM borax‐boric acid (pH 8.7) as BGE were employed after optimization. The calibration curves were linear for PNA concentration ranging from 1 to 50 μmol/L. LOD and LOQ of PNA were 0.2 and 1.0 μmol/L, respectively. Since the commercially available reagent gives rise to huge PNA peak and an apparent impurity peak, the purity of PNA was evaluated to be about 81.4% by CZE method, obviously lower than the supplier's purity value of 99.9% evaluated by RP–HPLC, and also lower than 94.8% determined with RP–HPLC by our research group. The CZE method takes only 5 min, needs only 90 nL PNA, much less than 20 min and 20 μL PNA in RP–HPLC method. Moreover, the CZE method is applicable for the analysis of glutamic acid modified and lysine modified PNAs, they show different migration time with their corresponding complementary PNAs. Our results show CZE provides a new choice for PNA and modified PNA analysis, also their purity or quality evaluation.     

Direct detection and discrimination of double-stranded oligonucleotide corresponding to hepatitis C virus genotype 3a using an electrochemical DNA biosensor based on peptide nucleic acid and double-stranded DNA hybridization

Development of an electrochemical DNA biosensor for the direct detection and discrimination of double-stranded oligonucleotide (dsDNA) corresponding to hepatitis C virus genotype 3a, without its denaturation, using a gold electrode is described. The electrochemical DNA sensor relies on the modification of the gold electrode with 6-mercapto-1-hexanol and a self-assembled monolayer of 14-mer peptide nucleic acid probe, related to the hepatitis C virus genotype 3a core/E1 region. The increase of differential pulse voltammetric responses of methylene blue, upon hybridization of the self-assembled probe with the target ds-DNA to form a triplex is the principle behind the detection and discrimination. Some hybridization experiments with non-complementary oligonucleotides were carried out to assess whether the developed DNA sensor responds selectively to the ds-DNA target. Diagnostic performance of the biosensor is described and the detection limit was found to be 1.8 × 10⁻¹² M in phosphate buffer solution, pH 7.0. The relative standard deviation of measurements of 100 pM of target ds-DNA performed with three independent probe-modified electrodes was 3.1%, indicating a remarkable reproducibility of the detection method.     

Improved nucleic acid triggered probe activation through the use of a 5-thiomethyluracil peptide nucleic acid building block

To improve the efficiency of a nucleic acid triggered probe activation (NATPA) system a 5-thiomethyluracil peptide nucleic acid (PNA) building block has been synthesized. Attachment of imidazole and a coumarin ester to uracils at the ends of two PNAs resulted in a 550 000-fold acceleration of DNA-triggered coumarin release relative to imidazole and a 6-fold increase in k(cat) relative to a system which had these groups attached to the amino and carboxy ends of PNAs. [structure: see text]     

Evidence for excited state intramolecular charge transfer in benzazole-based pseudo-stilbenes

Two azo compounds were obtained through the diazotization reaction of aminobenzazole derivatives and N,N-dimethylaniline using clay montmorillonite KSF as catalyst. The synthesized dyes were characterized using elemental analysis, Fourier transform infrared spectroscopy, and (13)C and (1)H NMR spectroscopy in solution. Their photophysical behavior was studied using UV-vis and steady-state fluorescence in solution. These dyes present intense absorption in the blue region. The spectral features of the azo compounds can be related to the pseudo-stilbene type as well as the E isomer of the dyes. Excitation at the absorption maxima does not produce emissive species in the excited state. However, excitation around 350 nm allowed dual emission of fluorescence, from both a locally excited (LE, short wavelength) and an intramolecular charge transfer (ICT, long wavelength) state, which was corroborated by a linear relation of the fluorescence maximum (ν(max)) versus the solvent polarity function (Δf) from the Lippert-Mataga correlation. Evidence of TICT in these dyes was discussed from the viscosity dependence of the fluorescence intensity in the ICT emission band. Theoretical calculations were also performed in order to study the geometry and charge distribution of the dyes in their ground and excited electronic states. Using DFT methods at the theoretical levels BLYP/Aug-cc-pVDZ, for geometry optimizations and frequency calculations, and B3LYP/6-311+G(2d), for single-point energy evaluations, the calculations revealed that the least energetic and most intense photon absorption leads to a very polar excited state that relaxes non-radioactively, which can be associated with photochemical isomerization.     

Hydrogen-bonding interactions in peptide nucleic acid and deoxyribonucleic acid: a comparative study

Peptide nucleic acid (PNA) is a synthetic analogue of deoxyribonucleic acid (DNA) capable of tightly binding to itself and DNA with high specificity. Using hybrid density functional methods, hydrogen-bond (H-bond) strengths have been evaluated for isolated Watson-Crick base pairs, PNA base pairs, and charged as well as neutral DNA base pairs. Heterogeneous base pairs of PNA with charged and neutral DNA have also been investigated. The competing effects of short-range H-bonding and long-range Coulombic repulsions in charged DNA base pairs have been analyzed. Polarizable continuum models have been employed to evaluate solvation effects on the binding energies.     

The nitrosation of N-alkylureas: Evidence for a proton transfer mechanism

The kinetics of the nitrosation of methyl, ethyl, propyl, butyl, and allyl urea were studied by conventional and stopped-flow spectrophotometry in the presence or absence of acetate or mono-, di-, or trichloroacetate anions. In the presence of a large excess of urea, the observed rate equation was where K_a is the acidity constant of nitrous acid and K_R that of the carboxylic acid. The ureas exhibited the reactivity order methylurea ≫ (ethylurea ≅ propylurea ≅ butylurea) ≫ allylurea. Experiments in D₂O afforded values of k/k = exp(0.130hv⌅/kT)], where v⌅ is the frequency of R₃N H stretching (2700–2250 cm⁻¹) in the protonated urea. This result, the observed catalysis by carboxylate ions and the value of the Bronsted parameter β(0.45) show the rate-controlling step of these reactions to be the transfer of a proton from the protonated N-alkyl-N-nitrosourea to the solvent or to the organic anion, if present. The observed order of substrate reactivities is explicable in terms of the capacity of the protonated N-alkyl-N-nitrosourea for forming a hydrogen bond with the water molecule to which the proton will be transferred, and the degree to which the formation of such bonds is hindered by the hydrophobic alkyl chain of the nitrosourea. © 1996 John Wiley & Sons, Inc.     

Morphological characterization of self-assembled peptide nucleic acid amphiphiles

Peptide nucleic acid amphiphiles (PNAA) are a promising set of materials for sequence-specific separation of nucleic acids from complex mixtures. To implement PNAA in micellar separations, the morphology and size of PNAA micelles in the presence and absence of a sodium dodecyl sulfate (SDS) cosurfactant have been studied by small-angle X-ray scattering and dynamic light scattering. We find that a 6-mer PNAA with a 12-carbon n-alkane tail forms ellipsoidal micelles (a = 5.15 nm; b = 3.20 nm) above its critical micelle concentration (CMC) of 110.9 microM. On addition of a stoichiometric amount of complementary DNA, PNAA hybridizes to DNA, suppressing the formation of PNAA micelles. At a ratio of 19:1 SDS/PNAA (total concentration = 20 mM), spherical micelles are formed with outer radius Rs = 2.67 nm, slightly larger than spherical micelles of pure SDS. Capillary electrophoresis studies show that PNAA/DNA duplexes do not comicellize with SDS micelles. No such effects are observed using noncomplementary DNA. The shape and size of the PNAA micelles is also verified by dynamic light scattering (DLS) studies. These results provide an interesting case study with competing electrostatic, hydrophobic, and hydrogen-bonding interactions in micellar systems and make possible the use of PNAA in micellar separations of DNA oligomers.     

DNA-templated polymerization of side-chain-functionalized peptide nucleic acid aldehydes

The DNA-templated polymerization of synthetic building blocks provides a potential route to the laboratory evolution of sequence-defined polymers with structures and properties not necessarily limited to those of natural biopolymers. We previously reported the efficient and sequence-specific DNA-templated polymerization of peptide nucleic acid (PNA) aldehydes. Here, we report the enzyme-free, DNA-templated polymerization of side-chain-functionalized PNA tetramer and pentamer aldehydes. We observed that polymerization of tetramer and pentamer PNA building blocks with a single lysine-based side chain at various positions in the building block could proceed efficiently and sequence specifically. In addition, DNA-templated polymerization also proceeded efficiently and in a sequence-specific manner with pentamer PNA aldehydes containing two or three lysine side chains in a single building block to generate more densely functionalized polymers. To further our understanding of side-chain compatibility and expand the capabilities of this system, we also examined the polymerization efficiencies of 20 pentamer building blocks each containing one of five different side-chain groups and four different side-chain regio- and stereochemistries. Polymerization reactions were efficient for all five different side-chain groups and for three of the four combinations of side-chain regio- and stereochemistries. Differences in the efficiency and initial rate of polymerization correlate with the apparent melting temperature of each building block, which is dependent on side-chain regio- and stereochemistry but relatively insensitive to side-chain structure among the substrates tested. Our findings represent a significant step toward the evolution of sequence-defined synthetic polymers and also demonstrate that enzyme-free nucleic acid-templated polymerization can occur efficiently using substrates with a wide range of side-chain structures, functionalization positions within each building block, and functionalization densities.     

Evaluation of different nucleic acid stains for sensitive double-stranded DNA analysis with capillary electrophoretic separation

This paper outlines the first use of SYTOX Orange, SYTO 82 and SYTO 25 nucleic acid stains for on-column staining of double-stranded DNA (dsDNA) fragments separated by capillary electrophoresis (CE). Low-viscosity, replaceable poly(vinylpyrrolidone) (PVP) polymer solution was used as the sieving matrix on an uncoated fused-silica capillary. The effects of PVP concentration, electric field strength, and incorporated nucleic acid stain concentrations on separation efficiency were examined for a wide range of DNA fragment sizes. Our study was focused on using nucleic acid stains efficiently excitable at a wavelength of 532 nm. Among the five tested nucleic acid stains, SYTOX Orange stain was shown to have the best sensitivity for dsDNA detection by CE. About a 500-fold lower detection limit was obtained compared to commonly used ethidium bromide and propidium iodide. SYTOX Orange stain also provided a wide linear dynamic range for direct DNA quantitation with on-line CE detection. Use of SYTOX Orange stain can greatly improve the measurement of DNA fragments by CE, which will enable an expanded set of applications in genomics and diagnostics.