Fiber-optic pH detection in small volumes of biosamples

Determining the pH values of microscopic plant samples may help to explain complex processes in plants, so it is an area of interest to botanists. Fiber-optic probes with small dimensions can be used for this purpose. This paper deals with the fiber-optic detection of the pH values of droplets of plant xylem exudate based on ratiometric fluorescence intensity measurements with an internal reference. For this purpose, novel V-taper sensing probes with a minimum diameter of around 8 μm were prepared that enable the delivery of fluorescence signal from the detection site on the taper tip to the detector. The taper tips were coated with pH-sensitive transducer (8-hydroxypyrene-1,3,6-trisulfonic acid trisodium salt; HPTS) and a reference [dichlorotris-(1,10-phenanthroline) ruthenium (II) hydrate (Ru-phen dichloride)] immobilized in a xerogel layer of propyltriethoxysilane and (3-glycidoxy)propyl trimethoxysilane. The prepared probes were sensitive to pH values mainly in the range from 6.0 to 9.0. In the pH range 6–9, the results were limited by measurement errors of about 0.2 pH units, and in the pH range 5–6 by measurement errors of about 0.5 pH units. Using the developed V-taper sensing probes, the pH values of in vivo and in vitro samples of small volumes (∼6 μl) of exudate were measured. The results were validated by comparison with conventional electrochemical pH measurements.     

Ratiometric detection of pH fluctuation in mitochondria with a new fluorescein/cyanine hybrid sensor

The homeostasis of mitochondrial pH (pH_m) is crucial in cell physiology. Developing small-molecular fluorescent sensors for the ratiometric detection of pH_m fluctuation is highly demanded yet challenging. A ratiometric pH sensor, Mito-pH, was constructed by integrating a pH-sensitive FITC fluorophore with a pH-insensitive hemicyanine group. The hemicyanine group also acts as the mitochondria targeting group due to its lipophilic cationic nature. Besides its ability to target mitochondria, this sensor provides two ratiometric pH sensing modes, the dual excitation/dual emission mode (D_ex/D_em) and dual excitation (D_ex) mode, and its linear and reversible ratiometric response range from pH 6.15 to 8.38 makes this sensor suitable for the practical tracking of pH_m fluctuation in live cells. With this sensor, stimulated pH_m fluctuation has been successfully tracked in a ratiometric manner via both fluorescence imaging and flow cytometry.     

Fluorescence ratiometric pH sensor prepared from covalently immobilized porphyrin and benzothioxanthene

A fluorescence ratiometric sensor for pH determination is described in this paper. The sensor incorporated the pH-sensitive dye meso-5,10,15,20-tetra-(4-allyloxyphenyl)porphyrin (TAPP) as an indicator and a pH-insensitive dye N-(2-methacryloxyethyl)benzo[k,l]thioxanthene-3,4-dicarboximide (MBTD), a benzothioxanthene derivative, as a reference for fluorescence ratiometric measurement. To prevent leakage of the dyes, both were photocopolymerized with acrylamide, hydroxyethyl methacrylate, and triethylene glycol dimethacrylate on the silanized glass surface. The reproducibility and response time of the prepared sensor were sufficient. Most common coexisting inorganic ions and organic compounds did not interfere with pH sensing. In the acidic pH range from 1.5 to 5.0 the fluorescence intensity ratio of the two dyes varied linearly as a function of pH. The sensing membrane was found to have a lifetime of at least one month. The sensor was applied to the analysis of waste water and artificial samples.     

A ratiometric CdSe/ZnS nanocrystal pH sensor

The development of a reversible chemical sensor based on a CdSe/ZnS nanocrystal (NC) is described. Signal transduction is accomplished by fluorescence resonance energy transfer (FRET) between the NC and a fluorescent pH-sensitive squaraine dye attached to the surface of the NC. The efficiency of FRET, and consequently the relative intensity of NC and dye emissions, is modulated with the pH-dependent absorption cross section of the squaraine dye. The design of a NC sensor based on FRET results in a ratiometric sensor since the emission intensities of dye and NC may be referenced to the isosbestic point between NC and dye emissions. The ratiometric approach allows sensing to be performed, regardless of issues surrounding collection efficiency (scattering environment, light fluctuations, etc.) and dye:NC loadings.     

A fluorescence ratiometric nano-pH sensor based on dual-fluorophore-doped silica nanoparticles

We have synthesized dual-fluorophore-doped core-shell silica nanoparticles used as ratiometric pH sensor. The nanoparticles were prepared with a reverse microemulsion technique by simultaneously encapsulating two different fluorophores, the pH-sensitive dye fluorescein as a pH indicator and the pH-insensitive dye phenosafranine as an internal reference for fluorescence ratiometric measurement, into silica shell. The nanoparticles prevent the fluorescence dyes leaching from the silica matrix when immersed inside water. The hydrophilic silica shells were made by hydrolysing and polymerizing tetraethoxysilane (TEOS) in water-in-oil microemulsion. The fluorescence intensity ratio of the two dyes varied linearly as a function of pH in the range from 4.0 to 8.0. The sensor was also applied to measure pH of real water samples. The results are in good agreements with that using the conventional glass electrode method. The as-prepared fluorescent nanoparticles showed rapid response, excellent stability and high reproducibility as pH sensors.     

Ratiometric temperature sensing with semiconducting polymer dots

This communication describes ultrabright single-nanoparticle ratiometric temperature sensors based on semiconducting polymer dots (Pdots). We attached the temperature sensitive dye-Rhodamine B (RhB), whose emission intensity decreases with increasing temperature-within the matrix of Pdots. The as-prepared Pdot-RhB nanoparticle showed excellent temperature sensitivity and high brightness because it took advantage of the light harvesting and amplified energy transfer capability of Pdots. More importantly, the Pdot-RhB nanoparticle showed ratiometric temperature sensing under a single wavelength excitation and has a linear temperature sensing range that matches well with the physiologically relevant temperatures. We employed Pdot-RhB for measuring intracellular temperatures in a live-cell imaging mode. The exceptional brightness of Pdot-RhB allows this nanoscale temperature sensor to be used also as a fluorescent probe for cellular imaging.     

Ratiometric fluorescent detection of acidic pH in lysosome with carbon nanodots

It is significant for cell physiology to keep the homeostasis of p H, and it is highly demanded to develop ratiometric fluorescent sensors toward p H. In this work, under mild condition, through the electrostatic interaction between carbon nanodots(CDs) and organic molecules, two novel ratiometric fluorescence hybrid nanosensors were fabricated for sensing acidic p H. These nanohybrid systems possess dual emission peaks at 455 and 527 nm under a single excitation wavelength of 380 nm in acidic p H condition.With the increasing of p H, the fluorescence of the 1,8-naphthalimide derivative completely quenches,while the blue fluorescence of CDs keeps constant. Furthermore, the CDsàorganic molecular nanohybrids exhibit excellent anti-disturbance ability, reversible p H sensing ability, and a linear response range in wide p H range respectively. Besides the ability to target lysosome, with one of the nanosensor, stimulated p H change has been successfully tracked in a ratiometric manner via fluorescence imaging.     

Delivery and subcellular targeting of dendrimer-based fluorescent pH sensors in living cells

Synthesis and targeted delivery of dendrimer-based fluorescent biosensors in living HeLa cells are reported. Following electroporation dendrimers are shown to display specific subcellular localization depending on their size and surface charge and this property is preserved when they are functionalized with sensing moieties. We analyze the case of double dendrimer conjugation with pH-sensitive and pH-insensitive molecules leading to the realization of ratiometric pH sensors that are calibrated in vitro and in living cells. By tuning the physicochemical properties of the dendrimer scaffold sensors can be targeted to specific cellular compartments allowing selective pH measurements in different organelles in living cells. In order to demonstrate the modularity of this approach we present three different pH sensors with tuned H(+) affinity by appropriately choosing the pH-sensitive dye. We argue that the present methodology represents a general approach toward the realization of targetable ratiometric sensors suitable to monitor biologically relevant ions or molecules in living cells.     

Dual Emission from Precious Metal-Free Luminophores Consisting of C,H, O,Si, and S/P at Room Temperature

Fluorescence–phosphorescence dual-emissive compounds are valuable tools for ratiometric luminescence sensing. Herein, it is reported that 2,5-bis(phenylsulfonyl)- and 2,5-bis[bis(4-methoxyphenyl)phosphinyl]-1,4-disiloxybenzenes exhibit dual emission with emission peaks that were easily identified without performing time-gated measurement. The disiloxybenzenes in powder simultaneously fluoresced and phosphoresced at 358–374 and 457–470 nm, respectively, under vacuum. The intensity ratios of the phosphorescence/fluorescence maxima of the disiloxybenzenes in powder and in a thin film of poly(methyl methacrylate) were sensitive to temperature and molecular oxygen, respectively. The plots of the relative intensity versus temperature or partial pressure of molecular oxygen were well fitted with calibration curves defined by an exponential approximation with excellent correlation coefficients R² (0.9708–0.9921), demonstrating the high potential of the disiloxybenzenes as precious metal-free probes applicable to ratiometric luminescence sensing.     

Dual‐fluorophore Raspberry‐like Nanohybrids for Ratiometric pH Sensing

We report on the development of raspberry‐like silica structures formed by the adsorption of 8‐hydroxypyrene‐1,3,6‐trisulfonate (HPTS)@silica nanoparticles (NPs) on rhodamine B isothiocyanate (RBTIC)@silica NPs for ratiometric fluorescence‐based pH sensing. To overcome the well‐known problem of dye leaching which occurs during encapsulation of anionic HPTS dye in silica NPs, we utilized a polyelectrolyte‐assisted incorporation of the anionic HPTS. The morphological and optical characterization of the as‐synthesized dye‐doped NPs and the resulting nanohybrids were carried out. The pH‐sensitive dye, HPTS, incorporated in the HPTS‐doped silica NPs provided a pH‐dependent fluorescence response while the RBITC‐doped silica provided the reference signal for ratiometric sensing. We evaluated the effectiveness of the nanohybrids for pH sensing; the ratio of the fluorescence emission intensity at 510 nm and 583 nm at excitation wavelengths of 454 nm and 555 nm, respectively. The results showed a dynamic response in the acidic pH range. With this approach, nanohybrids containing different dyes or receptors could be developed for multifunctioning and multiplexing applications.     

Colorimetric and Fluorescent Bimodal Ratiometric Probes for pH Sensing of Living Cells

pH measurement is widely used in many fields. Ratiometric pH sensing is an important way to improve the detection accuracy. Herein, five water‐soluble cationic porphyrin derivatives were synthesized and their optical property changes with pH value were investigated. Their pH‐dependent assembly/disassembly behaviors caused significant changes in both absorption and fluorescence spectra, thus making them promising bimodal ratiometric probes for both colorimetric and fluorescent pH sensing. Different substituent identity and position confer these probes with different sensitive pH‐sensing ranges, and the substituent position gives a larger effect. By selecting different porphyrins, different signal intensity ratios and different fluorescence excitation wavelengths, sensitive pH sensing can be achieved in the range of 2.1–8.0. Having demonstrated the excellent reversibility, good accuracy and low cytotoxicity of the probes, they were successfully applied in pH sensing inside living cells.     

Boron Doped Carbon Dots with Unusually High Photoluminescence Quantum Yield for Ratiometric Intracellular pH Sensing

Herein we report that boron doping in carbon dots results in increased photoluminescence (PL) quantum yield, which could be used for ratiometric intracellular pH sensing in cancer cell lines. Using a mixture of citric acid monohydrate, thiourea, and boric acid, microwave-assisted synthesis of boron doped blue emitting carbon dots (B-Cdots) with an average size of 3.5±1.0 nm was achieved. For B-Cdots, the maximum quantum yield (QY) was observed to be 25.8 % (11.1 % (w/w) H₃BO₃ input concentration), whereas, the same was calculated to be 16.9 % and 11.4 % for Cdots (synthesized from citric acid monohydrate and thiourea only) and P-Cdots (phosphorus doped carbon dots; synthesized using citric acid monohydrate, thiourea and phosphoric acid) (11.1 % (w/w) H₃PO₄ input concentration), respectively. The observed luminescence efficiencies as obtained from steady state and time-resolved photoluminescence measurements suggest an alternative emission mechanism due to boron/phosphorus doping in carbon dots. We furthermore demonstrated facile composite formation using B-Cdots and another carbon dots with orange emission in presence of polyvinyl alcohol (PVA), resulting in white light emission (0.31, 0.32; λ_ex 380 nm). The white light emitting composite enabled ratiometric pH sensing in the aqueous medium and showed favorable uptake properties by cancerous cells for intracellular pH sensing as well.     

Ratiometric fluorescence detection of bleomycin based on proximity-dependent fluorescence conversion of DNA-templated silver nanoclusters

We design a ratiometric fluo rescent sensing platform for bleomycin(BLM) by using proximity-dependent DNA-templated silver nanoclusters(DNA-AgNCs) probe.This ratiometric sensing system is constructed with DNA-AgNCs as single fluorophore.The proposed strategy is based on the two following facts:(1) a covert DNA can approach and transform the DNA-AgNCs with green emission(G-DNA-AgNCs) into red emission through hybridization reaction.(2) The specific cleavage of the convert DNA by BLM in the presence of Fe(Ⅱ) inhibits the discoloration of G-DNA-AgNCs.Thus,benefiting from the specific recognition of BLM and unique properties of G-DNA-AgNCs,a hignly-sensitive ratiometric sensor for BLM has been successfully developed.The detection limit is as low as 30 pmol/L.This label-free fluorescence probe possesses advantages of convenient synthetic process and low cost.Moreover,this ratiometric method has been applied to the detection of BLM in human serum samples,illustrating a promising tool for analysis of BLM in cancer therapy.     

A ratiometric fluorescence sensor with broad dynamic range based on two pH-sensitive fluorophores

This paper describes a novel ratiometric fluorescence sensor for pH measurement. Two pH-sensitive fluorophores, N-allyl-4-(4'-methyl-piperazinyl)-1,8-naphthalimide (AMPN) and meso-5,10,15,20-tetra-(4-allyloxyphenyl)porphyrin (TAPP), which served as referencing indicators for each other, were co-polymerized with acrylamide, hydroxyethyl methacrylate and triethylene glycol dimethacrylate on the silanized glass surface. The proposed sensor is based on the pH-dependent fluorescence intensities of the two fluorophores in different pH ranges. The sensor covers a broad dynamic range of pH 1.5-9.0. It exhibits satisfactory analytical performance in terms of selectivity, reproducibility and stability. The successful fabrication of the proposed sensor provides an alternative concept to utilizing two or more fluorophores for the development of ratiometric sensors covering a broad range of pH.     

Integrated chemical sensor array platform based on a light emitting diode, xerogel-derived sensor elements, and high-speed pin printing

We report a new, solid-state, integrated optical array sensor platform. By using pin printing technology in concert with sol-gel-processing methods, we form discrete xerogel-based microsensor elements that are on the order of 100 μm in diameter and 1 μm thick directly on the face of a light emitting diode (LED). The LED serves as the light source to excite chemically responsive luminophores sequestered within the doped xerogel microsensors and the analyte-dependent emission from within the doped xerogel is detected with a charge coupled device (CCD). We overcome the problem of background illumination from the LED reaching the CCD and the associated biasing that results by coating the LED first with a thin layer of blue paint. The thin paint layer serves as an optical filter, knocking out the LEDs red-edge spectral tail. The problem of the spatially-dependent fluence across the LED face is solved entirely by performing ratiometric measurements. We illustrate the performance of the new sensor scheme by forming an array of 100 discrete O₂-responsive sensing elements on the face of a single LED. The combination of pin printing with an integrated sensor and light source platform results in a rapid method of forming (∼1 s per sensor element) reusable sensor arrays. The entire sensor array can be calibrated using just one sensor element. Array-to-array reproducibly is <8%. Arrays can be formed using single or multiple pins with indistinguishable analytical performance.     

以AmberlystA－27为载体的光纤铁反射传感器的研究

以ＡｍｂｅｒｌｙｓｔＡ－２７为载体的光纤铁反射传感器的研究卢建忠，章竹君（南京大学化学系，南京，２１０００８）（陕西师范大学化学系，西安，７１００６２）关键词光纤传感器，反射，铁离子金属离子光纤传感器的设计是基于固定在探头上的指示剂与溶液中金属离子之...     

植入式光电极器件发展

Optogenetics transforms specific types of neurons through genetic engineering to achieve the cell membrane expression of photosensitive channel protein. When a specific wavelength of light irradiates the photosensitive channel protein, the cell is either excited or inhibited. Optogenetics provides a precise and fast method to control the activity of individual neurons for neuroscience research, which has gained increasing attention as a means of neural regulation. To realize the photogenetic regulation of neurons, light should be introduced into the brain safely and efficiently. Thus, specialized photoelectric devices are needed. Optrode plays a significant role in the application of optogenetics tools, which is the technical basis for the application of optogenetics. Optrode is a kind of implantable neural interface device. It can introduce light into the brain to regulate neural activity and record the changes of neural electrical signals under the control of lights. As the research of optogenetic technology continues, More and more optrodes are being developed and applied in the study of neuroscience and diseases, such as neural circuit, cognition and memory, epilepsy, and sensory function damage. The combination of optrode with optogenetic technologies provides various developmental modes in terms of material selection, device structure, light supply method, and integrated ways. The difficulty in fabricating optrodes lies in performing light stimulation and electrical signal recording without causing the immune rejection of the test animal and affecting its normal physiological activities simultaneously. In this study, based on structural characteristics and manufacturing process, optrodes are classified into two categories: waveguide-based and micro-light emitting diode-based. Subsequently, based on manufacturing process and light supply method, waveguide-based optrodes are further divided into optical fiber-optrode, optical waveguide-optrode based on MENS technology, and LD/LED waveguide-optrode. Similarly, micro-light emitting diode-based optrodes are divided into hard μLED optrode and soft μLED optrode. The advantages and disadvantages of different types of optrodes, as well as the evolution direction, are reviewed and summarized. Additionally, problems with existing optrodes, such as signal quality, biocompatibility, and device reliability, are discussed. Further, the ideal form of the device is presented as possessing the following characteristics: μLED and recording electrode integrated on flexible substrate, small size, high spatial resolution, high biocompatibility, wireless energy supply, wireless data transmission, etc. As optrode technologies are continuously updated, in the application of optogenetic technologies, research on brain neural circuit and functional structure will be better studied, and various nerve diseases will be gradually tamed.     

Miniaturized optical chemosensor for flow-based assays

A cost-effective, highly compact, and versatile optoelectronic device constructed of two ordinary light emitting diodes compatible with optosensing films has been developed. This fibreless device containing chemoreceptor, semiconductor light source, and detector integrated in a miniaturized flow-through cell of low microliter internal volume works as a complete photometric chemical sensor suitable for detection in flow analysis. The operation of the developed device under nonstationary programmable-flow conditions offered by sequential injection analysis has been demonstrated using Prussian Blue film as a model optical chemoreceptor. The unique spectroelectrochemical properties of the sensing material enable its use for optical sensing of redox species, whereby ascorbic acid and hydrogen peroxide have been chosen as model analytes. The reported SI-sensor system features fast and reproducible determination of both analytes in the submillimolar range of concentrations. The construction concept demonstrated in this work can be easily applied to other kinds of optical sensors based on absorbance sensing films.     

Ratiometric luminescent molecular oxygen sensors based on uni-luminophores of C^N Pt(II)(acac) complexes that show intense visible-light absorption and balanced fluorescence/phosphorescence dual emission

Uni-luminophores of C^N cyclometalated Pt(II) complexes with balanced room temperature fluorescence/phosphorescence dual emission were prepared for ratiometric oxygen sensing in both intensity mode and lifetime mode.     

Enhanced fluorescence cyanide detection at physiologically lethal levels: reduced ICT-based signal transduction

Three water-soluble fluorescent probes have been specifically designed to determine free cyanide concentrations up to physiologically lethal levels, >20 microM. The probes have been designed in such a way as to afford many notable sensing features, which render them unique with regard to signal transduction, photophysical characteristics, and their application to physiological cyanide determination and safeguard. The probes are readily able to reversibly bind free aqueous cyanide with dissociation constants around 4 microM3. Subsequent cyanide binding modulates the intramolecular charge transfer within the probes, a change in the electronic properties within the probes, resulting in enhanced fluorescence optical signals as a function of increased solution cyanide concentration. The ground-state chelation with cyanide produces wavelength shifts, which also enable the probes to sense cyanide in both an excitation and emission ratiometric manner, in addition to enhanced fluorescence signaling. This has enabled a generic cyanide sensing platform to be realized that is not dependent on fluorescent probe concentration, probe photodegradation, or fluctuations in the intensity of any employed excitation sources, ideal for remote cyanide sensing applications. Further, the >600 nm fluorescence emission of the probes potentially allows for enhanced fluorescence ratiometric cyanide sensing in the optical window of tissues and blood, facilitating their use for the transdermal monitoring of cyanide for mammalian safeguard or postmortem in fire victims, both areas of active research.