Synthesis of nano-sized crystalline oxide ion conducting fluorite-type Y2O3-doped CeO2 using perovskite-like BaCe0.9Y0.1O2.95 (BCY) and study of CO2 capture properties of BCY

Formation of nano-sized Y₂O₃-doped CeO₂ (YCO) was observed in the chemical reaction between proton conducting Y₂O₃-doped BaCeO₃ (BCY) and CO₂ in the temperature range 700-1000 °C, which is generally prepared by wet-chemical methods that include sol-gel, hydrothermal, polymerization, combustion, and precipitation reactions. BCY can capture CO₂ of 0.13 g per ceramic gram at 700 °C, which is comparable to that of the well-known Li₂ZrO₃ (0.15 g per ceramic gram at 600 °C). Powder X-ray diffraction (PXRD), energy dispersive X-ray analysis (EDX), laser particle size analysis (LPSA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and ac impedance spectroscopy were employed to characterize the reaction product obtained from reaction between BCY and CO₂ and subsequent acid washing. PXRD study reveals presence of fluorite-like CeO₂ (a=5.410 (1) Å) structure and BaCO₃ in reaction products. TEM investigation of the acid washed product showed the formation of nano-sized material with particle sizes of about 50 nm. The electrical conductivity of acid washed product (YCO) in air was found to be about an order higher than the undoped CeO₂ reported in the literature.     

Photoacoustic study of CO2-laser coincidences with absorption of some organic solvent vapours

Detection of specific molecules in the atmosphere is motivated by the need for monitoring the emission of industrial pollutants. CO₂-laser photoacoustic (PA) spectroscopy was used here to obtain coincidence spectra of the vapours of three organic solvents: trichloroethylene (TCE), benzene, and dioxan. Spectra of coincidences were obtained as a function of total pressure, adding dry air to the vapour of the solvents up to 1000 mbar.A narrow cavity photoacoustic cell with window acoustic buffers was built for improved sensitivity, and is reported here.The vapour molecules studied do have some significant absorption in the CO₂-laser region, or close to it, but that fact does not necessarily lead to usable coincidences with the narrow laser lines. The results reveal several prominent coincidences that can be used for practical purposes, especially in the case of trichloroethylene.     

Preparation of COF2 using CO2 and F2 in the electrochemical cell with PbSnF4 as a solid electrolyte

Tetragonal PbSnF₄ was prepared by precipitation method with Pb(NO₃)₂ and SnF₂ aqueous solutions. The product was characterized using X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XFS), and the other chemical analyses. Tetragonal PbSnF₄ exhibited the highest electric conductivity of 3.2 Sm⁻¹ at 473 K in air as a fluoride ion conductor. We have investigated the possibility of COF₂ formation using CO₂ and F₂ in an electrochemical cell with PbSnF₄ as a solid electrolyte. At same time, we tried to produce an electric power from an electrochemical cell. This CO₂/F₂ electrochemical cell was constructed with a tetragonal PbSnF₄ disk having Au electrodes. The electromotive force was about 0.9 V at room temperature for 0.1 MPa CO₂/(0.01 MPa F₂ + 0.09 MPa Ar). However, the short circuit current density was 0.24 A m⁻², which was quite small. This current density was so small that no fluorocarbon compound was detected after 3 h discharge using FT-IR.     

IR laser decomposition of 1,3-disilacyclobutane in presence of carbon disulfide: chemical vapour deposition of polythiacarbosilane

TEA CO₂ laser irradiation of gaseous mixtures of 1,3-disilacyclobutane - carbon disulfide affords chemical vapour deposition of solid polythiacarbosilane films that possess Si-S-X (X = Si, C), S-H and Si-H bonds and undergo slow hydrolysis in air to polyoxothiacarbosilanes containing Si-H, Si-O-Si and (C)S-H bonds. The formation of the polythiacarbosilane is proposed to take place via polymerization of transient silene and incorporation of CS₂ into growing polysilene network.     

Hydrogen gas mixture separation by CVD silica membrane

In this work we investigate the performance of high flux chemical vapour deposition (CVD) silica membranes for the separation of gas mixtures containing H₂ and CO₂ at various temperatures. The membranes were prepared by a counter diffusion CVD method where tetraethyl orthosilicate (TEOS) and O₂ were used as reactants. Single gas permeation resulted in activated transport for the smaller kinetic diameter gases (H₂ and He) whilst the larger kinetic diameter gases (CO₂ and N₂) showed negative activation energy. The single gas permeation of H₂ increased from 5.1 × 10⁻⁷ to 7.0 × 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ in the temperature range 100–400 °C, and H₂/CO₂ and H₂/N₂ selectivities reached 36 and 57 at 400 °C, respectively. The H₂ purity in the permeate stream also increased with temperature for H₂:CO₂ binary gas mixture, thus being beneficial for H₂ diffusion. H₂ competitively permeated through the membrane at a several range of gas mixtures, and a saturation level was achieved at H₂:CO₂ 60:40 feed concentration, where the diffusion of CO₂ molecules became negligible delivering ∼99% H₂ purity in the permeate stream. These results substantiate that the counter diffusion CVD method produced thin silica film membranes with a very precise pore size control, in particular suggesting a narrow pore distribution with average pore radius of about 3.1 Å.     

A comparative study of the effects of different buffer gases on the line shape of water vapour rovibronic transition

The line shape parameters of water vapour rovibrational transition at 12145.444 cm⁻¹ belonging to the (2ν₁ + ν₂ + ν₃) overtone band in the presence of three buffer gases He, N₂ and CO₂ are studied by high resolution near infrared (NIR) diode laser spectrometer. The wavelength modulation spectroscopy (WMS) is adopted to probe buffer gas broadened first derivative (1f) signal of water vapour transition. The simulation of the experimental signals based on Voigt profile provides the collisional broadening coefficients and line strength parameters. The comparison is made between the broadening effects on water vapour transition induced by He, N₂ and CO₂.     

The solid state reaction between lanthanum oxide and strontium carbonate

The reaction between lanthanum oxide and strontium carbonate was studied non-isothermally between 350 and 1150 °C at different heating rates, intermediates and the final solid product were characterized by X-ray diffractometry (XRD). The reaction proceeds through formation of lanthanum oxycarbonate La₂O(CO₃)₂, lanthanum dioxycarbonate La₂O₂CO₃, and non-stoichiometric strontium lanthanum oxide La₂SrO_x (x = 4 + δ). La₄SrO₇ was found to be the final product which begins to form at ∼700 °C. Li⁺ doping enhances the formation of the final product as well as commencement of the reactions at lower temperatures.     

High-pressure phase behaviour of binary (CO2 + nicotine) and ternary (CO2 + nicotine + solanesol) mixtures

This work paper presents vapour–liquid equilibrium (VLE) data for binary (CO₂ + nicotine) and ternary (CO₂ + nicotine + solanesol) mixtures, at 313.2 K and 6, 8 and 15 MPa. The (CO₂ + nicotine) system exhibits three phases (L₁L₂V) in equilibrium at 8.37 MPa. It is estimated that this system most likely follows the type-III phase behaviour. In the ternary system, the presence of solanesol in the vapour phase was detected only at the pressure of 15 MPa. At this pressure, partition coefficients and separation factors for solanesol/nicotine were calculated for different initial nicotine/solanesol compositions and a strong influence of composition was found. The results were modelled using the Peng–Robinson equation of state (PR EOS) coupled with the Mathias–Klotz–Prausnitz (MKP) mixing rule (PR–MKP model). Good correlations of the binary data, particularly in the case of the (CO₂ + nicotine) mixture, were obtained. However, the model could not correlate the ternary data.     

Single-walled carbon nanotubes as stationary phase in gas chromatographic separation and determination of argon, carbon dioxide and hydrogen

A chromatographic technique is introduced based on single-walled carbon nanotubes (SWCNTs) as stationary phase for separation of Ar, CO₂ and H₂ at parts per million (ppm) levels. The efficiency of SWCNTs was compared with solid materials such as molecular sieve, charcoal, multi-walled carbon nanotubes and carbon nanofibers. The morphology of SWCNTs was optimized for maximum adsorption of H₂, CO₂ and Ar and minimum adsorption of gases such as N₂, O₂, CO and H₂O vapour. To control temperature of the gas chromatography column, peltier cooler was used. Mixtures of Ar, CO₂ and H₂ were separated according to column temperature program. Relative standard deviation for nine replicate analyses of 0.2 mL H₂ containing 10 μL of each Ar or CO₂ was 2.5% for Ar, 2.8% for CO₂ and 3.6% for H₂. The interfering effects of CO, and O₂ were investigated. Working ranges were evaluated as 40-600 ppm for Ar, 30-850 ppm for CO₂ and 10-1200 ppm for H₂. Significant sensitivity, small relative standard deviation (RSD) and acceptable limit of detection (LOD) were obtained for each analyte, showing capability of SWCNTs for gas separation and determination processes. Finally, the method was used to evaluate the contents of CO₂ in air sample.     

New solid-state synthesis routine and mechanism for LiFePO4 using LiF as lithium precursor

Li₂CO₃ and LiOH·H₂O are widely used as Li-precursors to prepare LiFePO₄ in solid-phase reactions. However, impurities are often found in the final product unless the sintering temperature is increased to 800 °C. Here, we report that lithium fluoride (LiF) can also be used as Li-precursor for solid-phase synthesis of LiFePO₄ and very pure olivine phase was obtained even with sintering at a relatively low temperature (600 °C). Consequently, the product has smaller particle size (about 500 nm), which is beneficial for Li-extraction/insertion in view of kinetics. As for cathode material for Li-ion batteries, LiFePO₄ obtained from LiF shows high Li-storage capacity of 151 mAh g⁻¹ at small current density of 10 mA g⁻¹ (1/15 C) and maintains capacity of 54.8 mAh g⁻¹ at 1500 mA g⁻¹ (10 C). The solid-state reaction mechanisms using LiF and Li₂CO₃ precursors are compared based on XRD and TG-DSC.     

PAMAM dendrimer composite membrane for CO2 separation: Formation of a chitosan gutter layer

A poly(amidoamine) (PAMAM) dendrimer composite membrane with an excellent CO₂/N₂ separation factor was developed in-situ. The In-situ Modification (IM) method was used to modify the surface of commercial porous membranes, such as ultrafiltration membranes, to produce a gas selective layer by controlling the interface precipitation of the membrane materials in the state of a received membrane module. Using the IM method, a chitosan layer was prepared on the inner surface of a commercially available ultrafiltration membrane as a gutter layer, in order to affix PAMAM dendrimer molecules on the porous substrate. After chitosan treatment, the PAMAM dendrimer was impregnated into the gutter layer to form a PAMAM/chitosan hybrid layer. The CO₂ separation performance of the resulting composite membrane was tested at a pressure difference of 100 kPa and a temperature of 40 °C, using a mixed CO₂ (5 vol%)/N₂ (95 vol%) feed gas. The PAMAM dendrimer composite membrane, with a gutter layer prepared from ethylene glycol diglycidyl ether and a 0.5 wt% chitosan solution of two different molecular weight chitosans, revealed an excellent CO₂/N₂ separation factor and a CO₂ permeance of 400 and 1.6 × 10⁻⁷ m³ (STP) m⁻² s⁻¹ kPa⁻¹, respectively. SEM observations revealed a defect-free chitosan layer (thickness 200 nm) positioned directly beneath the top surface of the UF membrane substrate. After PAMAM dendrimer treatment, the hybrid chitosan/PAMAM dendrimer layer was observed with a thickness of 300 nm. XPS analysis indicated that the hybrid layer contained about 20–40% PAMAM dendrimer.     

Carbon nanotube networks as gas sensors for NO2 detection

Networks of different carbon nanotube (CNT) materials were investigated as resistive gas sensors for NO₂ detection. Sensor films were fabricated by airbrushing dispersions of double-walled and multi-walled CNTs (DWNTs and MWNTs, respectively) on alumina substrates. Sensors were characterized by resistance measurements from 25 to 250 °C in air atmosphere in order to find the optimum detection temperature. Our results indicate that CNT networks were sensitive to NO₂ concentrations as low as 0.1 ppm. All tested sensors provided significantly lower response to interfering gases such as H₂, NH₃, toluene and octane. We demonstrate that the measured sensitivity upon exposure to NO₂ strongly depends on the employed CNT material. The highest sensitivity values were obtained at temperatures ranging between 100 and 200 °C. The best sensor performance, in terms of recovery time, was however achieved at 250 °C. Issues related to the gas detection mechanisms, as well as to CNT network thermal stability in detection experiments performed in air at high operation temperatures are also discussed.     

VLE of CO2 + glycerol + (ethanol or 1-propanol or 1-butanol)

Vapour-liquid equilibrium of CO₂ + [0.00871 glycerol + 0.99129 (ethanol or 1-propanol or 1-butanol)] mixtures was measured at the temperatures of 313.15 K and 333.15 K, and close to the critical line, at pressures up to 12 MPa. On the liquid side, the bubble points measured for these ternary mixtures follow closely the behaviour of VLE reported by several authors for the corresponding binary mixtures without glycerol. On the vapour side, however, dew points for the ternary mixtures deviate significantly from VLE results for the binaries. A correlation of the results obtained for the CO₂ + glycerol + ethanol mixture with the Peng-Robinson equation of state, admitting quasi-binary behaviour, equally yields good agreement on the liquid side, and significant deviations on the vapour side.     

Facile fabrication of a novel high performance CO2 separation membrane: Immobilization of poly(amidoamine) dendrimers in poly(ethylene glycol) networks

Poly(amidoamine) (PAMAM) dendrimers showed high CO₂ separation properties and were successfully immobilized in a poly(ethylene glycol) (PEG) network upon photopolymerization of PEG dimethacrylate. The PAMAM dendrimer incorporation ratio was readily controlled, and a stable self-standing membrane containing up to 75 wt.% PAMAM dendrimer was obtained. The CO₂ separation properties over smaller H₂ were investigated by changing the PAMAM dendrimer content or generation and CO₂ partial pressure (ΔPCO₂$\mathrm{\Delta }{P}_{\text{C}{\text{O}}_2}$) under atmospheric conditions. Especially, a polymeric membrane containing 50 wt.% PAMAM dendrimer (0th generation) exhibited an excellent CO₂/H₂ selectivity of 500 with CO₂ permeability of 2.74 × 10⁻¹⁴ m³(STP)m/(m² s Pa) or 3.65 × 10³ barrer (1 barrer = 7.5 × 10⁻¹⁸ m³(STP)m/(m² s Pa)) when a mixture gas (CO₂/H₂: 5/95 by vol.) was fed at 25 °C and 100 kPa with 80% relative humidity. This polymeric materials are promising for a novel CO₂ separation membrane.     

Prussian Blue electrodeposited on MWNTs-PANI hybrid composites for H2O2 detection

A Prussian Blue (PB)/polyaniline (PANI)/multi-walled carbon nanotubes (MWNTs) composite film was fabricated by step-by-step electrodeposition on glassy carbon electrode (GCE). The electrode prepared exhibits enhanced electrocatalytic behavior and good stability for detection of H₂O₂ at an applied potential of 0.0 V. The effects of MWNTs thickness, electrodeposition time of PANI and rotating rate on the current response of the composite modified electrode toward H₂O₂ were optimized to obtain the maximal sensitivity. A linear range from 8 × 10⁻⁹ to 5 × 10⁻⁶ M for H₂O₂ detection has been observed at the PB/PANI/MWNTs modified GCE with a correlation coefficient of 0.997. The detection limit is 5 × 10⁻⁹ M on signal-to-noise ratio of 3. To the best of our knowledge, this is the lowest detection limit for H₂O₂ detection. The electrode also shows high sensitivity (526.43 μA μM⁻¹ cm⁻²) for H₂O₂ detection which is more than three orders of magnitude higher than the reported.     

Use of near-infrared reflectance spectroscopy for shelf-life discrimination of green asparagus stored in a cool room under controlled atmosphere

This study sought to evaluate the ability of near-infrared reflectance spectroscopy (NIRS) to classify intact green asparagus, in refrigerated storage under controlled atmosphere, by storage time and post-harvest treatments applied. A total of 468 green asparagus (Asparagus officinalis, L., cultivar UC-157) were sampled after 7, 14, 21 and 28 days of refrigerated storage (2 °C, 95% R.H.) under three controlled atmosphere (CA) treatments: air (21 kPa O₂ + 0.3 kPa CO₂), CA₁ (5 kPa O₂ + 5 kPa CO₂) and CA₂ (10 kPa O₂ + 10 kPa CO₂). Two commercially available spectrophotometers were evaluated for this purpose: a scanning monochromator (SM) of 400-2500 nm and a combination of diode array and scanning monochromator (DASM) of 350-2500 nm. Models developed using partial least squares 2-discriminant analysis (PLS2-DA) correctly classified between 81-100% of samples by post-harvest storage time, depending on the instrument used. Using similar models, the DASM instrument correctly classified 85% of samples by post-harvest treatment, compared with 72% using the SM. These results confirmed that NIR spectroscopy, coupled with the use of chemometric techniques, provides a reliable, accurate method of predicting the shelf-life of asparagus under different storage conditions and as a function of post-harvest treatment applied; the method can be readily applied at industrial level.     

A study on methanol steam reforming to CO2 and H2 over the La2CuO4 nanofiber catalyst

The La₂CuO₄ crystal nanofibers were prepared by using single-walled carbon nanotubes as templates under mild hydrothermal conditions. The steam reforming of methanol (SRM) to CO₂ and H₂ over such nanofiber catalysts was studied. At the low temperature of 150 °C and steam/methanol=1.3, methanol was completely (100%, 13.8 g/h g catalyst) converted to hydrogen and CO₂ without the generation of CO. Within the 60 h catalyst lifespan test, methanol conversion was maintained at 98.6% (13.6 g/h g catalyst) and with 100% CO₂ selectivity. In the meantime, for distinguishing the advantage of nanoscale catalyst, the La₂CuO₄ bulk powder was prepared and tested for the SRM reaction for comparison. Compared with the La₂CuO₄ nanofiber, the bulk powder La₂CuO₄ showed worse catalytic activity for the SRM reaction. The 100% conversion of methanol was achieved at the temperature of 400 °C, with the products being H₂ and CO₂ together with CO. The catalytic activity in terms of methanol conversion dropped to 88.7% (12.2 g/h g catalyst) in 60 h. The reduction temperature for nanofiber La₂CuO₄ was much lower than that for the La₂CuO₄ bulk powder. The nanofibers were of higher specific surface area (105.0 m²/g), metal copper area and copper dispersion. The in situ FTIR and EPR experiments were employed to study the catalysts and catalytic process. In the nanofiber catalyst, there were oxygen vacancies. H₂-reduction resulted in the generation of trapped electrons [e] on the vacancy sites. Over the nanofiber catalyst, the intermediate H₂CO/HCO was stable and was reformed to CO₂ and H₂ by steam rather than being decomposed directly to CO and H₂. Over the bulk counterpart, apart from the direct decomposition of H₂CO/HCO to CO and H₂, the intermediate H₂COO might go through two decomposition ways: H₂COO=CO+H₂O and H₂COO=CO₂+H₂.     

Biodegradable poly(l-lactic acid) nanofiber prepared by a carbon dioxide laser supersonic drawing

Biodegradable poly(l-lactic acid) (PLLA) nanofiber was prepared by a carbon dioxide (CO₂) laser supersonic drawing which was carried out by irradiating the laser on an as-spun fiber in a supersonic jet. The supersonic jet was generated by blowing off air into a vacuum chamber from a fiber supplying orifice. The flow velocity from the orifice can be estimated by applying Graham’s theorem from the pressure difference between the atmospheric pressure and the pressure of the vacuum chamber. The fastest flow velocity estimated was 396 m s⁻¹ when the chamber pressure was 6 kPa. The PLLA nanofiber having an average diameter of 0.132 μm was obtained when the supersonic drawing was carried out by irradiating the laser at 177 W cm⁻² on the as-spun fiber supplied at 0.1 m min⁻¹ in the vacuum chamber at 6 kPa. The obtained nanofiber had a draw ratio of about 323,000 and a degree of crystallinity of 45%, and its diameter uniformity was high. The CO₂ laser supersonic drawing was a new route for preparation of various nanofibers without using any solvent.     

A novel gaseous pinacolyl alcohol sensor utilizing cataluminescence on alumina nanowires prepared by supercritical fluid drying

A cataluminescence (CTL) sensor using Al₂O₃ nanowires as the sensing material was developed for the determination of trace pinacolyl alcohol in air samples based on the catalytic chemiluminescence (CL) of pinacolyl alcohol on Al₂O₃ nanowires. Eight catalysts were examined and the CL intensity on Al₂O₃ nanowires prepared by supercritical fluid drying was the strongest. This novel CL sensor showed high sensitivity and selectivity to gaseous pinacolyl alcohol at optimal temperature of 340 °C. Quantitative analysis was performed at a wavelength of 460 nm. The linear range of CTL intensity versus concentration of gaseous pinacolyl alcohol was 0.09 × 10⁻⁶ to 2.56 × 10⁻⁶ g mL⁻¹ (r = 0.9983, n = 6) with a detection limit (3σ) of 0.0053 × 10⁻⁶ g mL⁻¹. None or only very low levels of interference were observed while the foreign substances such as water vapor, ethanol, ammonia, chloroform, benzene, nitrogen dioxide, methylbenzene, hydrochloric acid, methanol and butanol were passing through the sensor. The response time of the sensor is less than 100 s, and the sensor had a long lifetime more than 60 h. The sensor would be potentially applied to analysis of the nerve agents such as Soman.     

CO2-laser photoacoustic detection of heavy water vapour. Basic principles

A CO₂-laser cw system and a photoacoustic detection apparatus, based on a nonresonant gas cell, was constructed and built. Coincidences of D₂O absorption with several laser lines were observed. The strongest absorption was observed with the line at 9.26 m, which was used in the experiments. Samples of deuterated water in the range from 10 to 100% deuterium were used to examine the behaviour of the photoacoustic signal under conditions of varying deuterium content and total vapour pressure. A principal calibration procedure with respect to this is proposed. The behaviour of the system on buffer gas introduction was examined with hydrogen and dry air. Self-buffering of water vapour is also discussed on the basis of the results.