A rapid spectrophotometric method for the determination of transparent exopolymer particles (TEP) in freshwater

A simple and rapid spectrophotometric method is proposed for the determination of transparent exopolymer particles (TEP) in freshwater samples. In this method, TEP reacts with excess of alcian blue solution yielding a low solubility dye-TEP complex. After centrifugation, the concentration of the remaining dye in the supernatant was determined at 602 nm and its concentration was related to the concentration of TEP in freshwater. The effect of alcian blue concentration from 1.5×10⁻³ to 9.0×10⁻³% (m/v), solution pH from 2.5 to 6.9 and stirring time from 20 to 120 s on the analytical curve was investigated. Under the optimum conditions established, such as alcian blue concentration of 3.0×10⁻³% (m/v); pH of 4.0 (0.2 mol l⁻¹ acetate buffer solution) and stirring time of 1 min, the analytical curve was linear from 0.50 to 10 μg ml⁻¹ (A=0.34−0.037[GX]; r²=0.9999; where A is the absorbance and [GX] the gum xanthan concentration in μg ml⁻¹) with a detection limit of 0.10 μg ml⁻¹. The recovery of TEP (as gum xanthan) for two samples ranged from 95.3 to 108 and the relative standard deviations (R.S.D.s) were lower than 0.8% for gum xanthan solutions at concentrations of 1.0 and 1.5 μg ml⁻¹ (n=8). The results obtained for TEP in freshwater samples using the proposed spectrophotometric method and those obtained using a literature method are in agreement at the 95% confidence level and within an acceptable range of error.     

Determination of clarithromycin in rat plasma by HPLC-UV method with pre-column derivatization

A novel high-performance liquid chromatographic (HPLC) method using pre-column derivatization and UV detection at 275 nm for the determination of clarithromycin in rat plasma has been validated. Clarithromycin was extracted from plasma sample spiked with internal standard (erythromycin) under alkaline condition with ethyl ether and derivatizated with trimethylbromosilane. The analyses were run on a C₁₈ column, maintained at 40 °C during elution, using a mobile phase comprised of potassium dihydrogen phosphate (50 mM, pH 6.8, contained 0.7% triethylamine), acetonitrile, and methanol (30:45:25, v/v/v). The standard calibration curve for clarithromycin was linear (r² = 0.9998) over the concentration range of 0.1-10 μg ml⁻¹ in rat plasma. The limit of detection (LOD) and limit of quantitation (LOQ) was 30 ng ml⁻¹ and 0.1 μg ml⁻¹ respectively. The intra- and inter-day assay variability range was 2.6-7.4% and 3.3-8.5%, respectively. This method has been successfully applied to a pharmacokinetic study of clarithromycin in rats.     

Ultra-trace level determination of hydroquinone in waste photographic solutions by UV-vis spectrophotometry

A simpler UV-vis spectrophotometric method was investigated for hydroquinone (HQ) determination using KMnO₄ as oxidizing agent for conversion of HQ to p-benzoquinone (BQ) as well as signal enhancer. Various parameters such as analytical wavelength, stability time, temperature, pH, solvent effect and interference of chemicals were checked and parameters optimized by using 1 μg ml⁻¹ standard solution of HQ. Beer's Law was applicable in the range of 0.07-2 μg ml⁻¹ and 0.005-0.05 μg ml⁻¹ at 245.5 nm and at 262 nm for aqueous standard solutions of HQ with linear regression coefficient value of 0.9978 and 0.9843 and detection limit of 0.021 μg ml⁻¹ and 0.0016 μg ml⁻¹ HQ, respectively. Standard deviation of 1.7% and 2.4% was true for 1 μg ml⁻¹ and 0.03 μg ml⁻¹ HQ solution (n = 11) run at respective wavelengths. The method was successfully applied to dilute waste photographic developer samples for free HQ determination.     

Simultaneous determination of 11 drugs belonging to four different groups in human urine samples by reversed-phase high-performance liquid chromatography method

A new, accurate, sensitive and fast reversed-phase high-performance liquid chromatography (RP-HPLC) as an analytical method for the quantitative determination of 11 drugs in human urine was worked out, optimized and validated. The objects of analysis were imipenem (IMP), paracetamol (PAR), dipyrone (DPR), vancomycin (VCM), amikacin (AMK), fluconazole (FZ), cefazolin (CFZ), prednisolone (PRE), dexamethasone (DEX), furosemide (FUR) and ketoprofen (KET) belonging to four different groups (antibiotics, analgesic, demulcent and diuretic). For HPLC analysis, diode array (DAD) and fluorescence (FL) detectors were used. The separation of analyzed compounds was conducted by means of a LiChroCART^® Purospher^® C₁₈e (125 mm × 3 mm, particle size 5 μm) analytical column with LiChroCART^® LiChrospher^® C₁₈ (4 mm × 4 mm, particle size 5 μm) pre-column with gradient elution. Analyzed drugs were determined within 20 min. The mobile phase was comprised of various proportions of methanol, acetonitrile and 0.05% trifluoroacetic acid in water. AMK was separated and determined from human urine using ortho-phthaldialdehyde-3-mercaptopropionic acid (OPA-3-MPA) as a fluorescent reagent by RP-HPLC-FL. The following retention times for drugs IMP, PAR, DPR, VCM, AMK, FZ, CFZ, PRE, DEX, FUR and KET in human urine were found: 4.01 min, 4.86 min, 6.71 min, 8.14 min, 9.46 min, 10.01 min, 10.90 min, 13.34 min, 14.06 min, 16.03 min and 18.98 min, respectively. Excellent linearity was obtained for compounds in the range of concentration: 0.35-42 μg ml⁻¹, 0.5-45 μg ml⁻¹, 4.5-38 μg ml⁻¹, 0.25-25 μg ml⁻¹, 0.5-35 μg ml⁻¹, 0.25-22 μg ml⁻¹, 0.03-52 μg ml⁻¹, 0.15-25 μg ml⁻¹, 0.25-28 μg ml⁻¹, 0.05-18 μg ml⁻¹ and 0.15-35 μg ml⁻¹ for IMP, PAR, DPR, VCM, AMK, FZ, CFZ, PRE, DEX, FUR and KET, respectively. The limits of detection (LOD) and limits of quantification (LOQ) for analyzed drugs were calculated in all cases and recovery studies were also performed. Ten human urine samples obtained from patients treated in hospital have been tested. In analyzed samples, one or more drugs from the 11 examined drugs were detected. The concentrations of examined drugs in urine samples ranged between: 1.5-12 μg ml⁻¹ of PAR, 5.2-11.5 μg ml⁻¹ of DPR, 0.13-9.5 μg ml⁻¹ of CFZ and 0.1-8 μg ml⁻¹ of FUR. This method can be successfully applied to routine determination of all these drugs in human urine samples.     

Non-equilibrium determination of metoclopramide and tetracaine hydrochloride by sequential injection spectrophotometry

A new sequential injection spectrophotometric method was proposed for the determination of metoclopramide and tetracaine hydrochloride. The method was based on the detection of an unstable red intermediate compound resulting from the reaction of metoclopramide or tetracaine hydrochloride with potassium dichromate, in the presence of sodium oxalate, in sulfuric acid solution. The related reaction mechanisms of this new method have been studied. The experimental conditions were optimized for the stopped-flow and continuous-flow sequential injection models. For continuous flow, the linear range for determination of metoclopramide, the detection limit and the sampling frequency were 13-130 μg ml⁻¹, 9.4 μg ml⁻¹ and 40 samples per hour, respectively. For stopped flow, they were 3-42 μg ml⁻¹, 1.0 μg ml⁻¹ and 18 h⁻¹, respectively. Adopting the continuous-flow model for tetracaine hydrochloride, the linear range was 25-300 μg ml⁻¹, and the detection limit was 18.0 μg ml⁻¹ with sampling frequency of 40 h⁻¹. This method has been used to determine metoclopramide and tetracaine hydrochloride in pharmaceutical preparations, and the results are compared with those determined by the pharmacopoeia method. Statistical analysis reveals that there was no evidence of significant difference between the methods.     

Simultaneous quantitation of loganin and sweroside in plasma using column-switching high-performance liquid chromatography

A column-switching high-performance liquid chromatography (HPLC) method is described for the simultaneous determination of loganin and sweroside, which are the active ingredients of purified herbal extract from Lonicera japonica (SKL JI), in rat plasma using column-switching and ultraviolet (UV) absorbance detection. Plasma was simply filtrated prior to injection to the HPLC system consisting of a clean-up column, a concentrating column, and an analytical column, which were connected with two six-port switching valves. Detection of loganin and sweroside was accurate and repeatable, with a limit of quantitation of 0.05 μg ml⁻¹ in plasma. The calibration curves for both loganin and sweroside were linear over the concentration ranges of 0.05-40.0 and 0.02-40.0 μg ml⁻¹ in rat plasma, respectively. The intra- and inter-day precision over the concentration range for loganin and sweroside were lower than 8.1 and 10.9% (relative standard deviation, R.S.D.), and accuracy was between 94.7 and 113.5 and 95.0 and 113.1%, respectively. This method has been successfully applied to determine the levels of loganin and sweroside in rat plasma samples from pharmacokinetics studies.     

Synchronous fluorescence determination of protein with functionalized CdS nanoparticles as a fluorescence probe

Nanometer-sized fluorescent particles have been successfully synthesized. A synchronous fluorescence method, with high sensitivity and selectivity, has been developed for rapid determination of protein with functionalized CdS as a fluorescence probe. When Δλ=260 nm, maximum synchronous fluorescence is produced at 274 nm at pH 7.0. Under optimal conditions, the calibration graphs are linear over the range 0.1-3.0 μg ml⁻¹ for bovine serum albumin (BSA), 0.1-11.0 μg ml⁻¹ for γ-globulin (γ-G) and 0.1-1.4 μg ml⁻¹ for human serum albumin (HSA), respectively. Limits of determination were 0.01 μg ml⁻¹ for BSA, 0.019 μg ml⁻¹ for γ-G and 0.021 μg ml⁻¹ for HSA, respectively. The relative standard deviations of seven replicate measurements were 1.8% for 1.0 μg ml⁻¹ BSA, 2.2% for 1.0 μg ml⁻¹ γ-G and 2.3% for 1.0 μg ml⁻¹ HSA.     

Determination of ternary mixtures of penicillin G, benzathine and procaine by liquid chromatography and factorial design study

In the present work, a rapid and sensitive method for simultaneous determination of penicillin G (PG), benzathine (BE) and procaine (PR) in drug and serum media is introduced. The polar hydro-organic (55/45) mobile phases containing an aqueous solution adjusted to pH = 3.7 and an organic solvent (MeOH) including triethylamine (TEA) and trifluroacetic acid (TFA) are used. The flow rate of 1 ml min⁻¹, a C₈ column (150 mm × 46 mm) with 5 μm i.d. and wavelength at 215 nm are selected for optimal separation condition. The limit of detection (LOD), linear concentration range and relative standard deviation (R.S.D.) of this method for the PG are 1.1 μg ml⁻¹, 10-2400 μg ml⁻¹ and 1.7% and for the BE are 1.2 μg ml⁻¹, 12-2100 μg ml⁻¹ and 1.8% and for the PR are 1.5 μg ml⁻¹, 20-2000 μg ml⁻¹ and 2%, respectively. The factorial design is used for the determination of main and interaction effects of pH, flow rate and concentration of MeOH, TEA and TFA in the separation at two levels. Also, the analysis of variance (ANOVA) table is obtained. The results show that TFA and TEA have higher effect than concentration of MeOH, pH and flow rate factors.     

A sequential injection fluorometric procedure for rapid determination of total protein in human serum

A sensitive procedure for the quantification of total protein bovine serum albumen (BSA) in human serum was presented with sequential injection sampling and fluorometric detection. A few microliters of sample and fluorescamine solutions were aspirated into the holding coil to facilitate the reaction of protein with fluorescamine by giving rise to a blue-green-fluorescent derivative. The derivative was afterwards excited by a 400 nm radiation from a UV radiator, and the emitted fluorescence was monitored at the wavelength of 470 nm. By loading 5.0 μl of sample and 4.0 μl of fluorescamine solution 0.075% (m/v), a linear calibration graph was obtained within 0.3-12.5 μg ml⁻¹, and a detection limit (3σ) of 0.1 μg ml⁻¹ was achieved, along with a sampling frequency of 40 h⁻¹ and a R.S.D. value of 2.1% at the 5.0 μg ml⁻¹ levels. Protein contents in human serums were analyzed by using the present procedure, and reasonable agreements were obtained with those obtained by a documented spectrophotometric (Biuret) method.     

Development of an optical chemical sensor based on 2-(5-bromo-2-pyridylazo)-5-(diethylamino)phenol in Nafion for determination of nickel ion

An optical chemical sensor based on immobilization of 2-(5-bromo-2-pyridylazo)-5-(diethylamino)phenol (Br-PADAP) in Nafion membrane is described. The membranes were cast onto glass substrates and were used for the determination of nickel in aqueous solutions by spectrophotometry. The sensor system is highly transparent, mechanically stable and showed no evidence of reagent leaching. The influence of several parameters such as pH, ligand concentration, and type and concentration of regenerating solution were optimized. The sensor system showed good sensitivity in the range 0.5-20 μg ml⁻¹ with a detection limit of 0.3 μg ml⁻¹ Ni(II). The sensor has been incorporated into a home-made flow-through cell for determination of nickel in flowing streams with improved sensitivity, precision and detection limit. The calibration curve in the flow system was linear in the range 0.1-16 μg ml⁻¹ with a detection limit of 0.07 μg ml⁻¹. The sensor is easily regenerated by dilute nitric acid solution. The proposed method was successfully applied to the determination of nickel content in vegetable oil and chocolate samples and the results were compared with those obtained using atomic absorption spectrometry.     

Micro determination of ascorbic acid using methyl viologen

A new simple and sensitive analytical spectrophotometric method is developed for the determination of ascorbic acid reduces methyl viologen to form a stable blue coloured free radical ion. This method has a sensitivity and lower limit detection of 0.1 μg ml⁻¹ of ascorbic acid (0.1 ppm) which is comparable to the flow injection analysis reported earlier. Beer's law is obeyed over the concentration range of 1.0-10 μg ml⁻¹ of ascorbic acid per 10 ml of the final solution (0.1-1.0 μg ml⁻¹) at 600 nm. The molar absorptivity and Sandell's sensitivity were found to be 1.5 × 10⁵ ± 100 l mol⁻¹ cm⁻¹ and 0.001 μg cm⁻², respectively. The method has been applied to the determination of ascorbic acid in food, pharmaceuticals and biological samples.     

Separation and determination of terbinafine and its four impurities of similar structure using simple RP-HPLC method

A novel reversed-phase HPLC method for the simultaneous determination of active component terbinafine, its one impurity 1-methylaminomethylnaphtalene and three degradation products, β-terbinafine, Z-terbinafine and 4-methyl-terbinafine occurring in pharmaceutical formulations after long-term stability tests, was developed and validated using propylparaben as an internal standard.The chromatographic separation was performed on a NUCLEOSIL 100-5-CN column, mobile phase for separation of all compounds consisted of a mixture of tetrahydrofurane, acetonitrile and citrate buffer pH 4.50 (10:20:70, v/v/v). The analysis time was less than 32 min at flow-rate of 0.8 ml min⁻¹. UV detection was performed at 226 nm. The method was validated and system suitability parameters were investigated. Method robustness and short-term standard solution stability were verified. Limits of detection for terbinafine degradation products/impurity were from 0.023 to 0.098 μg ml⁻¹, limits of quantitation were from 0.078 to 0.327 μg ml⁻¹. The method was applicable for routine determination of terbinafine and all its found impurities of similar structure with sufficient selectivity, precision and accuracy.     

Flow-injection chemiluminescence assay for ultra-trace determination of DNA using rhodamine B-Ce(IV)-DNA ternary system in sulfuric acid media

A novel flow-injection chemiluminescence method for the determination of DNA at ultra-trace level has been established. In 0.8 M sulfuric acid media, the chemiluminescence of the rhodamine B-cerium (IV) or Ce(IV) system is enhanced by DNA, activated previously by imidazole-HCl buffer solution (pH 7.0). The enhanced intensity of chemiluminescence is in proportion to log DNA concentration 1.0×10⁻⁸ to 0.1 μg ml⁻¹ for herring sperm DNA and 2.0×10⁻⁶ to 0.2 μg ml⁻¹ for calf thymus DNA with 3σ detection limits of 8.3×10⁻⁹ μg ml⁻¹ for herring sperm DNA and 3.5×10⁻⁷ μg ml⁻¹ for calf thymus DNA, respectively. The relative standard deviation for 1.0×10⁻⁴ μg ml⁻¹ herring sperm DNA was 0.99% and 2.0×10⁻³ μg ml⁻¹ for calf thymus DNA was 1.1% (n=11). Using the optimized system, DNA contents in six synthetic samples has been determined with recoveries of 99.5-109.0%. The possible mechanism has also been studied in this paper.     

Functionalized semiconductor nanocrystals for ultrasensitive detection of peptides

Semiconductor CdS nanoparticle have been prepared and modified with thiovanic acid. The functionalized nanoparticles are water-soluble. They were used as the fluorescence probes in the ultrasensitive detection of peptides. This method is based on the fluorescence enhancement of functionalized nano-CdS in the presence of peptide with mercapto groups (GN-9) and the fluorescence quenching of functionalized nano-CdS in the presence of peptide (GA-8 and MT-25). Excitation and emission wavelengths were 360 and 530 nm, respectively. Under optimum conditions, the calibration graphs are linear over the range of 0.15-3.5, 0.2-4.0, and 0.2-3.8 μg ml⁻¹ for GN-9, GA-8 and MT-25, respectively. The corresponding detection limits were 0.010 μg ml⁻¹ for GN-9, 0.018 μg ml⁻¹ for GA-8 and 0.022 μg ml⁻¹ for MT-25, respectively. This method has been proved to be a simple, rapid and sensitive method.     

Flow injection chemiluminescence determination of carbaryl using photolytic decomposition and photogenerated tris (2,2′-bipyridyl)ruthenium(III)

A flow injection (FI) system combined with two photochemical processes is developed for the sensitive and rapid determination of carbaryl. It is based on the on-line photo-conversion of carbaryl into methylamine which subsequently reacts with Ru(bpy)₃³⁺ generated through the on-line photo-oxidation of Ru(bpy)₃²⁺ with peroxydisulphate. The linear concentration range of application was 0.04-4.0 μg ml⁻¹ of carbaryl, with an R.S.D. of 1.2% (for a level of 0.50 μg ml⁻¹) and a detection limit of 0.012 μg ml⁻¹. The sample throughput was 200 injections per hour. The applicability of the method was demonstrated by determining carbaryl in commercial formulations, water, soil, grain and blood serum.     

Use of a solid sensing zone implemented with unsegmented flow analysis for simultaneous determination of thiabendazole and warfarin

For the first time, a solid sensing zone implemented with unsegmented flow analysis is described for the simultaneous determination of two pesticides, thiabendazole and warfarin. The system works as a simple and rapid spectrofluorimetric biparameter sensor. The sensor is based on the retention of the analytes on the sensing solid zone (octadecyl silane C₁₈ gel) placed in the detection zone itself into a quartz flow-cell. A temporary sequentiation in the arrival of the analytes to the sensing zone is achieved by on line separation using a pre-column of the same gel placed just before the flow cell. Thiabendazole is determined the first (using methanol 30% (v/v) as carrier/elution solution) because it passes through the pre-column while warfarin is strongly retained in it. Then, warfarin is conveniently eluted from the pre-column (using methanol 50% (v/v) as carrier/elution solution) the intrinsic fluorescence peak height measured at an excitation wavelength of 309 nm and an emission wavelength of 368 nm is used as analytical signal. Using a low sample volume (40 μl), the analytical signal showed a very good linearity in the range 10-800 ng ml⁻¹ and 2-40 μg ml⁻¹ with detection limits of 2.35 ng ml⁻¹ and 0.54 μg ml⁻¹ for thiabendazole and warfarin, respectively. The sensor was satisfactorily applied to the determination of these two analytes in pesticides and pharmaceutical preparations.     

Determination of quinolizidine alkaloids in Sophora medicinal plants by capillary electrophoresis

A new capillary electrophoresis (CE) method for the determination of quinolizidine alkaloids in Sophora medicinal plants was developed. A total of seven alkaloid components (cytisine, sophocarpine, matrine, lehmannine, sophoranol, oxymatrine and oxysophocarpine) were separated within 15 min. The running buffer was a 50 mM phosphate buffer containing 1%HP-β-CD and 3.3% isopropanol. The linear calibration ranges were 5.50-88.0 μg ml⁻¹ for cytisine and lehmannine, 5.00-88.0 μg ml⁻¹ for sophocarpine and sophoranol, 5.60-89.6 μg ml⁻¹ for matrine and oxysophocarpine, and 24.0-384 μg ml⁻¹ for oxymatrine. The recoveries of the seven alkaloids were 96.0-102.9% with relative standard deviations from 1.50 to 3.00% (n = 5). The method was successfully applied to different Sophora medicinal plants including Sophora flavescens, Sophora tonkinensis and Sophora alopecuroides.     

Determination of andrographolide and dehydroandrographolide in rabbit plasma by on-line solid phase extraction of high-performance liquid chromatography

The high-performance liquid chromatography (HPLC) coupled with on-line solid phase extraction (SPE) and ultraviolet (UV) detection was developed for determining andrographolide and dehydroandrographolide in rabbit plasma. Plasma samples (100 μL) were injected directly into a C18 SPE column and the biological matrix was washed out for 6 min using 15% aqueous methanol. By rotation of the switching valve, andrographolide and dehydroandrographolide were eluted in the back-flush mode and transferred to the analytical column by the chromatographic mobile phase consisted of methanol:acetonitrile (ACN):water (50:10:40; v/v). The UV detection was performed at 225 nm. The calibration curves showed excellent linear relationship (R ≥ 0.9993) over the concentration range of 0.05-5.0 μg mL⁻¹. The within- and between-day precisions (R.S.D.) of two analytes were in the range of 1.2-6.5% and the accuracies were between 92.0% and 102.1%. Their recoveries were all greater than 94%. The limits of detection were 0.019 μg mL⁻¹ for andrographolide and 0.022 μg mL⁻¹ for dehydroandrographolide. This method was successfully applied to the plasma concentration-time curve study after oral administration of Andrographis paniculata Nees extract in rabbit.     

Flow-injection chemiluminescence determination of dihydralazine sulfate based on hexacyanoferrate(III) oxidation sensitized by eosin Y

A novel flow-injection chemiluminescence (CL) method for the determination of dihydralazine sulfate (DHZS) is described. The method is based on the reaction between DHZS and hexacyanoferrate(III) in alkaline solution to give weak CL signal, which is dramatically enhanced by eosin Y. The CL emission allows quantitation of DHZS concentration in the range 0.02-2.8 μg ml⁻¹ with a detection limit (3σ) of 0.012 μg ml⁻¹. The experimental conditions for the CL reaction are optimized and the possible reaction mechanism is discussed. The method has been applied to the determination of DHZS in pharmaceutical preparations and compared well with the high performance liquid chromatography (HPLC) method.     

Determination of palladium in various samples by atomic absorption spectrometry after preconcentration with dimethylglyoxime on silica gel

A preconcentration method based on the adsorption of palladium-dimethylglyoxime (DMG) complex on silica gel for the determination of palladium at trace levels by atomic absorption spectrometry (AAS) has been developed. The retained palladium as Pd(DMG)₂ complex was eluted with 1 mol l⁻¹ HCl in acetone. The effect of some analytical parameters such as pH, amount of reagent and the sample volume on the recovery of palladium was examined in synthetic solutions containing street dust matrix. The influence of some matrix ions on the recovery of palladium was investigated by using the developed method when the elements were present both individually and together. The results showed that 2500 μg ml⁻¹ Na⁺, K⁺, Mg²⁺, Al³⁺ and Fe³⁺; 5000 μg ml⁻¹ Ca²⁺ ; 500 μg ml⁻¹ Pb²⁺; 125 μg ml⁻¹ Zn²⁺; 50 μg ml⁻¹ Cu²⁺ and 25 μg ml⁻¹ Ni²⁺ did not interfere with the palladium signal. At the optimum conditions determined experimentally, the recovery for palladium was found to be 95.3±1.2% at the 95% confidence level. The relative standard deviation and limit of detection (3s/b) of the method were found to be 1.7% and 1.2 μg l⁻¹, respectively. In order to determine the adsorption behaviour of silica gel, the adsorption isotherm of palladium was studied and the binding equilibrium constant and adsorption capacity were calculated to be 0.38 l mg⁻¹ and 4.06 mg g⁻¹, respectively. The determination of palladium in various samples was performed by using both flame AAS and graphite furnace AAS. The proposed method was successfully applied for the determination of palladium in the street dust, anode slime, rock and catalytic converter samples.