Peak capacity in gradient reversed-phase liquid chromatography of biopolymers. Theoretical and practical implications for the separation of oligonucleotides

Reversed-phase ultra-performance liquid chromatography was used for biopolymer separations in isocratic and gradient mode. The gradient elution mode was employed to estimate the optimal mobile phase flow rate to obtain the best column efficiency and the peak capacity for three classes of analytes: peptides, oligonucleotides and proteins. The results indicate that the flow rate of the Van Deemter optimum for 2.1 mm I.D. columns packed with a porous 1.7 microm C18 sorbent is below 0.2 mL/min for our analytes. However, the maximum peak capacity is achieved at flow rates between 0.15 and 1.0 mL/min, depending on the molecular weight of the analyte. The isocratic separation mode was utilized to measure the dependence of the retention factor on the mobile phase composition. Constants derived from isocratic experiments were utilized in a mathematical model based on gradient theory. Column peak capacity was predicted as a function of flow rate, gradient slope and column length. Predicted peak capacity trends were compared to experimental results.     

Effects of Blending Bare-Silica and Reversed-Phase on Retention of Neutral Compounds in Capillary Electrochromatography

Most commercially available instruments for capillary electrochromatography (CEC) have a fixed configuration and lack the flexibility to use shorter columns. Applying a blended stationary phase (a phase consisting of a given ratio of bare silica and reversed phase material) can simulate columns of different length in CEC. The goal of this work was to examine the effect of the degree of blending of reversed-phase columns (with bare silica) on the speed of the separation of neutral compounds in CEC. Optimum column packing mixture was determined from the variation of the solute retention factors as a function of the ratios of blending of reversed-phase and bare silica. By adjusting the column composition, solute retention factors and the analysis run time were halved when compared to a pure reversed-phase column of the same length. Stationary phase blending can be considered as an additional parameter to mobile phase variation, column temperature and applied electric field for the optimization of selectivity and analysis time. By adjusting the stationary phase composition, mobile phase composition, column temperature and applied electric field, the analysis run time of neutral components was decreased more than 75% when compared to a separation obtained on neat reversed-phase column of the same dimensions. The linear dependence of the retention factors as a function of the blend ratio (reversed phase/bare silica) offers a framework for designing a “blended” packed capillary column for CEC separations.     

Optimization of capillary parameters for gas chromatography

An HETP equation for the capillary column is developed that takes into account the dependence of gaseous diffusion on pressure, the compressibility of the mobile phase, together with the unique relationship between mobile phase velocity, and the resistance to mass transfer in the stationary phase. The equation is used to develop a procedure for column optimization and expressions are derived that allow the optimum column radius and optimum column length to be calculated for a given fixed inlet pressure. It is shown that fast, simple separations are optimally achieved using relatively short small diameter columns. Conversely, optimum performance for the separation of complex mixtures requiring higher efficiencies requires the use of long columns with relatively large diameters.     

High-performance liquid chromatographic enantioseparation of alpha-substituted glycine analogs on a quinine-based anion-exchanger chiral stationary phase under variable temperature conditions

The retention of enantiomers of chiral analytes, i.e. alpha-substituted glycine analogs, on a quinine-based anion-exchanger chiral stationary phase was studied in the temperature range of 5-70 degrees C and at different mobile phase compositions, using isocratic elution in the reversed-phase mode. By variation of both mobile phase composition and temperature, baseline separations could be achieved for these enantiomers. Separation could be optimized more quickly by adjusting the column temperature rather than the mobile phase composition. The dependence of the natural logarithms of retention and selectivity factors (lnk' and lnalpha) on the inverse of temperature, 1/T (van't Hoff plots) was used to determine thermodynamic data on the enantiomers. Calculated thermodynamic constants (Delta(DeltaH degrees ), Delta(DeltaS degrees ) and Delta(DeltaG degrees )) were applied to promote an understanding of the thermodynamic driving forces for retention in this chromatographic system. The elution sequence of the enantiomers in most cases was determined.     

Effect of the mobile phase on the retention behaviour of optical isomers of carboxylic acids and amino acids in liquid chromatography on bonded Teicoplanin columns

Conditions for separation of enantiomers of underivatized amino acids phenyl glycine and tryptophan and of mandelic acid as test compounds were studied on a Chirobiotic T column packed with amphoteric glycopeptide Teicoplanin covalently bonded to the surface of silica gel. The effects of the mobile phase composition on the retention and selectivity under analytical conditions, on the profile of the adsorption isotherms of the enantiomers and on the overloaded separation were investigated. The concentration of ethanol or of methanol in aqueous-organic mobile phases and the pH of the mobile phase affect not only the retention and selectivity, the saturation capacity and the isotherm profile, but also the solubility of the acids, which should be taken into account in development of preparative separations. A compromise between the separation selectivity and the solubility should be made in selecting the mobile phase suitable to accomplish preparative separations at acceptable production rate and throughput of the operation.     

Synthesis and chromatographic properties of an HPLC chiral stationary phase based upon human serum albumin

Summary A new HPLC stationary phase was synthesized by thein situ covalent immobilization of human serum albumin (HSA). The protein was immobilized on a commerically available diol column which had been activated with 1,1-carbonyldiimidazole. Initial chromatographic studies show that this phase can be used for chiral separations of enantiomeric solutes and that these separations may reflectin vitro binding to the HSA. The effects of mobile phase composition and temperature on the stereochemical resolutions are reported.     

CEC separation of peptides using a poly(hexyl acrylate-co-1,4-butanediol diacrylate-co-[2-(acryloyloxy)ethyl]trimethyl ammonium chloride) monolithic column

A polyacrylate-based monolithic column bearing cationic functionalities and designed for capillary electrochromatography (CEC) has been prepared via photopolymerization of a mixture of hexyl acrylate, butanediol diacrylate, 2-(acryloyloxy) ethyltrimethyl ammonium chloride (monomers), azobisisobutyronitrile (photoinitiator), acetonitrile, phosphate buffer, and ethanol (porogens). The polymerization process was initiated with UV light at 360 nm. The column performance was evaluated via the separations of alkylbenzenes, substituted anilines, basic drugs, peptides, and a protein digest. The separation of complex peptide mixtures was then studied since such separations constitute a promising application of capillary electrochromatography. In particular, the effects of mobile phase composition, including ionic strength of the buffer solution and the percentage of acetonitrile on the retention factor, the column efficiency, and the resolution were determined. The separations were affected by both interaction of the peptides with the stationary phase and their own electrophoretic mobility. Excellent separations with column efficiencies of up to 160 000 plates/m were achieved for both a mixture of ten well-defined peptides and a tryptic digest of cytochrome c. The fractions of eluent containing peptides of the digest separated in the monolithic column were collected and characterized using matrix-assisted laser desorption ionization mass spectrometry.     

On-line high-performance liquid-chromatographic separation and cold vapor atomic absorption spectrometric determination of methylmercury and inorganic mercury

A reversed-phase high-performance liquid chromatography (HPLC) method with cold vapor atomic absorption spectrometry (CV-AAS) detection is developed for mercury speciation. In this paper, the efficiency of tetrabutylammonium bromide reagent and sodium chloride in a methanol-water mixture as mobile phase is evaluated for HPLC separation of methylmercury and inorganic mercury coupled with on-line CV-AAS determination. Both mercury species are separated on a reversed-phase C(18) column. Several parameters (e.g. composition and flow-rate of mobile phase) are investigated for the optimization of HPLC separations. CV-AAS technique parameters are also studied for their effect on sensitivity (sodium borohydride and sodium hydroxide concentrations in the reducing agent, reducing agent flow-rate, length of the reduction coil and nitrogen flow-rate). Quantitative recoveries for both inorganic mercury and methylmercury are obtained from a spiked natural water sample.     

Sulfonated cyclofructan 6 based stationary phase for hydrophilic interaction chromatography

A stationary phase composed of silica-bonded sulfonated cyclofructan 6 (SCF6) was synthesized and evaluated for hydrophilic interaction chromatography (HILIC). The separation of a large variety of polar compounds was evaluated on different versions of the stationary phase and compared with the same separations obtained with commercially available HILIC columns. The new columns successfully separate polar and hydrophilic compounds including β blockers, xanthines, salicylic acid related compounds, nucleic acid bases, nucleosides, maltooligosaccharides, water soluble vitamins and amino acids. The separation conditions were optimized by changing the composition and the pH of the mobile phase. The dependence of analyte retention on temperature was studied using van't Hoff plots. The newly synthesized stationary phase showed broad applicability for HILIC mode separations.     

Chiral separation of lipoxygenase metabolites utilizing high-performance liquid chromatography

An isocratic, reversed-phase HPLC assay has been developed for the separation of the enantiomers of four lipoxygenase metabolites, without the need for a derivatization step. Separation of the enantiomers was studied on a polysaccharide type chiral stationary phase column. Upon determination of suitable mobile phase composition, the assay was evaluated at various temperatures. In all cases the R enantiomer eluted before the S enantiomer. The best separations were observed at 0 degrees C.     

High-performance liquid chromatography with contactless conductivity detection for the determination of peptides and proteins using a monolithic capillary column

Gradient programs were applied to the determination of peptides and proteins in HPLC with contactless conductivity detection. A monolithic capillary column was used for the fast and sensitive determination of the biochemical species in acidic mobile phases consisting of acetic acid or trifluoroacetic acid in various concentrations of acetonitrile in water. The drift in baseline, which is caused by conductivity changes during the elution program, was minimized by careful optimization of the composition of the mobile phase and remaining drift was removed by computational baseline normalization. The flow rate from a conventional HPLC pump was reduced to a flow rate suitable for capillary systems using a pre-column flow splitter and a final total flow rate of 1.65 microl/min was used for all capillary HPLC separations. The contactless conductivity detector was positioned directly on the outlet capillary of the separation column and positively charged peptides and proteins were determined as sharp and symmetrical peaks. Detection limits in a concentration range from 3.7 x 10(-8) to 5.1 x 10(-7)M and a reproducibility of peak areas and peak heights between 2.3% and 7.3% were achieved for all biochemical species tested.     

Analyses of benzophenones by capillary electrochromatography using methacrylate ester-based monolithic columns

In this study, eight benzophenones, which are commonly used as UV filters in various cosmetics and plastics, were analyzed by capillary electrochromatography with a methacrylate ester-based monolithic column. The effects of the composition and pH of mobile phase, porogenic solvent ratio, and 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) content on benzophenone separations were examined. For all benzophenones, separation performances were markedly improved in monolithic columns with larger 1-propanol ratio and higher AMPS content. Furthermore, a twofold increase in AMPS content almost reduced the separation time in half when a monolithic column had an adequately high surface area, i.e. monolithic column was produced in a higher ratio of 1-propanol. As well, the retention behaviors of these analytes in the monolithic column were strongly influenced by the level of acetonitrile in the mobile phase, and the pH of the mobile phase also had an apparent influence on separation resolution.     

Pressure drop effects on selectivity and resolution in packed column supercritical fluid chromatography

The influence of pressure drop on retention, selectivity, plate height and resolution was investigated systematically in packed supercritical fluid chromatography (SFC) using pure carbon dioxide as the mobile phase. Numerical methods developed previously which enabled the prediction of pressure gradients, diffusivities, capacity factors, plate heights and resolutions along the length of the column were used for the model calculations. The effects of inlet pressure and supercritical fluid flow rate on selectivity and resolution are studied. In packed column SFC with pure carbon dioxide as the mobile phase, the pressure drop can have a significant effect on resolution. The flow rate is shown to have a larger effect than generally realized. The calculated data are shown to be in good agreement with the experimental results. Finally, the variation of the chromatographic parameters along a 5.5 meter long model SFC column is illustrated. The possibilities and limitations of using long packed columns in SFC are discussed. It is demonstrated that long columns with large plate numbers do not necessarily yield better separations.     

Comparison of the separation of proteins of wide-ranging molecular weight via trilobal polypropylene capillary-channeled polymer fiber,commercial superficiously porous,and commercial size exclusion columns

Reversed phase and size-exclusion chromatography methods are commonly used for protein separations, although they are based on distinctly different principles. Reversed phase methods yield hydrophobicity-based (loosely-termed) separation of proteins on porous supports, but tend to be limited to proteins with modest molecular weights based on mass transfer limitations. Alternatively, size-exclusion provides complementary benefits in the separation of higher mass proteins based on entropic, not enthalpic, processes, but tend to yield limited peak capacities. In this study, microbore columns packed with a novel trilobal polypropylene capillary-channeled polymer fiber were used in a reversed phase modality for the separation of polypeptides and proteins of molecular weights ranging from 1.4 to 660 kDa. Chromatographic parameters including gradient times, flow rates, and trifluoroacetic acid concentrations in the mobile phase were optimized to maximize resolution and throughput. Following optimization, the performance of the trilobal fiber column was compared to two commercial-sourced columns, a superficially porous C4-derivatized silica and size exclusion, both of which are sold specifically for protein separations and operated according to the manufacturer-specified conditions. In comparison to the commercial columns, the fiber-based column yielded better separation performance across the entirety of the suite, at much lower cost and shorter separation times.     

Effects of high pressure in liquid chromatography

All the experimental parameters that the chromatographers are used to consider as constant (the column length and its diameter, the particle size, the column porosities, the phase ratio, the column hold-up volume, the pressure gradient along the column, the mobile phase density and its viscosity, the diffusion coefficients, the equilibrium constants, the retention factors, the efficiency parameters) depend on pressure to some extent. While this dependence is negligible as long as experiments, measurements, and separations are carried out under conventional pressures not exceeding a few tens of megapascal, it is no longer so when the inlet pressure becomes much larger and exceeds 100 MPa. Equations are developed to determine the extent of the influence of pressure on all these parameters and to account for it. The results obtained are illustrated with graphics. The essential results are that (1) many parameters depend on the inlet pressure, hence on the flow rate; (2) the apparent reproducibility of parameters as simple as the retention factor will be poor if measurements are carried out at different flow rates, unless due corrections are applied to the results; (3) the influence of the temperature on the equilibrium constants should be studied under constant inlet pressure rather than at a constant flow rate, to minimize the coupling effect of pressure and temperature through the temperature dependence of the viscosity; and (4) while reproducibility of results obtained at constant pressure and flow rate will not be affected, method development becomes far more complex because of the pressure dependence of everything.     

High-performance liquid chromatographic separation of position isomers using metal-organic framework MIL-53(Al) as the stationary phase

Metal-organic framework MIL-53(Al) was explored as the stationary phase for high-performance liquid chromatographic separation of position isomers using a binary and/or polar mobile phase. Baseline separations of xylene, dichlorobenzene, chlorotoluene and nitrophenol isomers were achieved on the slurry-packed MIL-53(Al) column with high resolution and good precision. The effects of mobile phase composition, injected sample mass and temperature were investigated. The separation of xylene, dichlorobenzene, chlorotoluene and nitrophenol isomers on MIL-53(Al) were controlled by entropy change.     

混合烷基开管电色谱柱的制备和评价

利用溶胶－凝胶（Sol-Gel）技术制备了混合烷基开管毛细管电色谱柱（C8－C13OT－CEC），并考察了其电渗流行为和电色谱性能。研究了流动相中甲醇含量对芳香族中性化合物保留的影响。发现C8－C18OT－CEC柱体现反相分配机理。5种芳香族化合物和4种苯同系物在C8－C13OT－CEC柱上分离良好，同时还考察了分离电压和柱内径对柱效的影响，结果表明高的电压和较小的柱内径能提高柱效。     

Reversed‐phase separation parameters for intact proteins using liquid chromatography with triple quadrupole mass spectrometry

The separation of intact proteins is inherently more complex than that of small molecules using reversed‐phase liquid chromatography. The goal of this work was to determine a reasonable set of operational parameters (a recommended starting point for other analysts) for the separation of intact proteins and their detection by triple quadrupole mass spectrometry. Although protein separations have been studied for many years, the direct detection of intact proteins with mass spectrometry requires special considerations of mobile phase additives to achieve efficient separation and sensitive detection. Myoglobin, cytochrome c, lactalbumin, lysozyme, and ubiquitin were used as model analytes to investigate chromatographic method development using a triple quadrupole mass spectrometer and detection by multiple reaction monitoring. Chromatographic parameters including the concentration of trifluoroacetic acid, flow rate, gradient slope, temperature, mobile phase composition, and stationary phase chemistry were evaluated. Protein charge state profiles were also monitored for temperature and modifier effects. An optimized method using 0.2 mL/min flow rate, 15% gradient slope, and 75°C with a combined trifluoroacetic acid and formic acid modified mobile phase was developed.     

Impact of pore structural parameters on column performance and resolution of reversed-phase monolithic silica columns for peptides and proteins

In this work, monolithic silica columns with the C4, C8, and C18 chemistry and having various macropore diameters and two different mesopore diameters are studied to access the differences in the column efficiency under isocratic elution conditions and the resolution of selected peptide pairs under reversed-phase gradient elution conditions for the separation of peptides and proteins. The columns with the pore structural characteristics that provided the most efficient separations are then employed to optimize the conditions of a gradient separation of a model mixture of peptides and proteins based on surface chemistry, gradient time, volumetric flow rate, and acetonitrile concentration. Both the mesopore and macropore diameters of the monolithic column are decisive for the column efficiency. As the diameter of the through-pores decreases, the column efficiency increases. The large set of mesopores studied with a nominal diameter of approximately 25 nm provided the most efficient column performance. The efficiency of the monolithic silica columns increase with decreasing n-alkyl chain length in the sequence of C18相似文献   

Capillary Electrochromatography as a Method Development Tool for the Liquid Chromatographic Separation of DUP 654 and Related Substances

Capillary Electrochromatography (CEC) offers a rapid, economical, and efficient means for resolving nonionic compounds in the reversed phase mode on octadecylsilane (ODS) columns. A CEC optimization on a Hypersil ODS capillary column was employed to identify a suitable mobile phase for the pressure-driven (reversed phase ODS) separation of the anti-inflammatory 2-phenylmethyl-1-naphthol (DUP 654), and its related substances. The proportions of mobile phase modifiers methanol, acetonitrile, and water as well as pH were employed as variables in a stacked mixture design. Comparable response surface profiles were obtained for the CEC separations at pH 4 and pH 8. However, subtle differences were evident in the quality of separations obtained in the liquid chromatographic (LC) mode when using a specially-prepared column packed with exactly the same stationary phase as used in the CEC experiments. A mapping of the response surface for separations on a commercially available Hypersil ODS LC column revealed obvious differences. The differences indicate that the transfer of ODS based separation methods between CEC and LC involves more than simply transferring the conditions from one mode to the other.