红外光谱法研究重质油分子的轻度热转化

为了从分子水平快速经济地分析重质油在热转化过程中的变化规律,利用四种模型化合物萘、四氢萘、十氢萘和正庚烷组成的混合体系来模拟重质油及其热转化缩合产物分子的基本组成,研究其红外吸收特性与平均分子参数（亚甲基和甲基的数目之比 N CH2/NCH3、芳氢率faH、芳香环系氢碳原子比NHar/NCar等）的关系。将重质油焦化重蜡油馏分进行轻度热转化,利用不同强度的系列溶剂将热转化产物的重质馏分顺序分离成系列溶剂族组分,将这些族组分进行红外分析。结果表明,混合物系列模拟体系的〖ＷＴＢＸ〗f〖ＷＴＢ１〗aH同其红外吸收在2750cm－1～3100cm－1的3000cm－1～3100cm－1强度分率（S3000~3100/S2750~3100）之间存在良好的线性关系,同时NCH2/NCH3 同2920cm－1和2960cm－1处的吸光度比值A2920/A2960之间也存在良好的线性关系。依据这些关系式可以合理解释重质油分子在热转化过程中分子结构的变化规律。随着重质油热转化的进行,NCH2/NCH3 饱和烃分子先增大后减小,芳香性族组分分子则持续降低;faH或NHar/NCar芳香性族组分分子呈现升高的趋势。     

Characterization of banana peel by scanning electron microscopy and FT-IR spectroscopy and its use for cadmium removal

This study describes the use of banana peel, a commonly produced fruit waste, for the removal of Cd(II) from environmental and industrial wastewater. The banana peel was characterized by FT-IR and scanning electron microscopy (SEM) coupled with energy dispersive X-ray (EDX) analysis. The parameters pH, contact time, initial metal ion concentration and temperature were investigated and found to be rapid ( approximately 97% within 10min). The Langmuir adsorption isotherm was used to describe partitioning behavior for the system at room temperature. The value of Q(L) was found to be (35.52mgg(-1)) higher than the previously reported materials. The binding of metal ions was found to be pH-dependent with the optimal sorption occurring at pH 8. The retained species were eluted with 5mL of 5x10(-3)M HNO(3) with the detection limit of 1.7x10(-3)mgL(-1). Kinetics of sorption followed the pseudo-first-order rate equation with the rate constant k, equal to 0.13+/-0.01min(-1). Thermodynamic parameters such as Gibbs free energy at 303K (-7.41+/-0.13kJmol(-1)) and enthalpy (40.56+/-2.34kJmol(-1)) indicated the spontaneous and endothermic nature of the sorption process. The developed method was utilized for the removal of Cd(II) ions from environmental and industrial wastewater samples using flame atomic absorption spectrophotometer (FAAS).     

Characterization of polymer soil burial degradation by thermal analysis and mechanical spectroscopy

Polypropylene (PP) and High density polyethylene (HDPE) / Polypropylene (PP) blend with different biodegradable additives (Granular starch/iron oxide mixture, Bioefect 72000 and Mater-Bi AF05H) were selected for degradation experiments. All the samples, processed by injection as seedboxes, have been subjected to an outdoor soil burial test and removed at different periods of time between 0 and 21 months. Their chemical structure and morphology have been analysed. Studies of dynamic-mechanical relaxation spectra of the samples before and after each exposure time have been carried out. The three characteristic relaxation zones α, β and γ, in order of decreasing temperature, have been obtained. It has been observed that due to the degradation process both, the HDPE/PP blend and the PP matrix, become more brittle than the undegraded ones regardless of the additive used. Degradation seems to start from the molecular chains of the amorphous phase or interfacial region. However the analysis of the mechanical behaviour manifested that the crystalline zone is also been affected by the exposure time.     

Enantioseparation of binaphthol and its mono derivatives by cyclodextrin-modified capillary zone electrophoresis

Chiral binaphthols belong to the group of most effective ligands for asymmetrical catalysis. In this context, various binaphthols presenting original substituents have been synthesized. Their study through capillary electrophoresis is the object of this work. The literature dedicated to the separation of atropisomers by capillary electrophoresis, corresponding only to binaphthol, reveals that its enantioseparation is always delicate because of the influence of many factors and the resolutions obtained are weak. Therefore, for a structured optimization, we first successfully evaluated the acidity constants of different binaphthols by means of capillary electrophoresis. With these known physicochemical characteristics, we could successfully carry out enantiomeric separations of the different binaphthols at pH 11.5, practically in completely ionized form, in phosphate medium, and in the presence of cyclodextrin (CD), with analysis times lower than 8min. The nature of CDs (alpha-CD, beta-CD, gamma-CD, hydroxypropyl-alpha-cyclodextrin (HP-alpha-CD), HP-beta-CD, HP-gamma-CD and trimethyl-beta-CD (TM-beta-CD)) and other factors in relation to enantiomeric resolution (applied voltage, nature and concentration of the electrolyte, and concentration of cyclodextrin) were optimized. These studies allowed us to determine the optimal conditions of separation (concentration and nature of CD) for each of the studied binaphthols. It is necessary to mention that, for the 1,1'-binaphthyl-2,2'-diol (Binol) at pH 11.5, the S atropisomer always migrated first, regardless of the nature and concentration of the cyclodextrin used. Moreover, an inversion in elution order of the two atropisomers as a function of pH was observed with gamma-CD (pH range: 10-11.5). The R atropisomer migrated first at pH 10. At pH 10.8 the migration order of the two atropisomers of Binol was reversed as a function of gamma-CD concentration. Finally, the addition of chiral ionic liquids (R(-)-1-hydroxy-N,N,N-trimethylbutan-2-aminium bis(trifluoromethylsulfonyl)imide and S(+)-tetrabutylammonium camphorsulfonate) was conducted. In the case of S(+)-tetrabutylammonium camphorsulfonate, a weak antagonistic effect was observed with modeling the evolution of enantiomeric resolution by means of the experimental design, while in the case of R(-)-1-hydroxy-N,N,N-trimethylbutan-2-aminium bis(trifluoromethylsulfonyl)imide the effect was neutral.     

Characterization of radix rehmanniae processing procedure using FT-IR spectroscopy through nonnegative independent component analysis

A method is proposed for monitoring the radix rehmanniae proparate processing procedure and determining the endpoint of the process using attenuated total reflectance (ATR) FT-IR through nonnegative independent component analysis (ICA). In the proposed method, ATR FT-IR spectra of the samples were firstly measured at different steaming periods. Then, nonnegative ICA was used for direct estimation of the feature spectra of the pure components in the mixture without pre-separation and other prior information. The estimated independent components (ICs) and their variation of the relative concentrations were used to characterize the processing procedure and determine the endpoint. The results show that the estimated three ICs are consistent with that of the chemical components in the mixtures, i.e. catalpol/rehmaionoside, glucose, and other compounds that nearly keep invariant during the processing procedure. The endpoint determined by the IR-ICA method is 15 h, which was located in the range obtained by expert sensory analysis, whereas the endpoint determined by the traditional sensory analysis is 14 ∼ 17 h and even 14 ∼ 20 h, which showed the significant deviation of the endpoints determined by different operators. Figure Characterisation of radix rehmanniae processing procedure using FT-IR spectroscopy through nonnegative independent component analysis     

Characterization of dental composites by thermal analysis, infrared spectroscopy and scanning electron microscopy

Commercial light-cured dental composites were used in this study. Two laboratorial composites, Resilab (Wilcos/Brazil), Epricord (Kuraray/Japan) were compared under cured and uncured conditions. Thermal analysis, infrared spectroscopy and scanning electron microscopy were used to evaluate the dental composites. The mass change and heat flow signals (TG–DSC) were recorded simultaneously by using STA 409 PC Luxx (NETZSCH), in the 25–800 °C temperature range at a heating rate of 10 °C/min under nitrogen atmosphere (70 mL/min). Employing thermo-microbalance TG 209 C F1 Iris (NETZSCH) coupled to the BRUKER Optics FTIR TENSOR, the samples were analyzed by combined thermogravimetric and spectroscopic methods (TG–FTIR). The initial sample mass was about ~12 mg, the data collection have been done in the 35–800 °C temperature range at a heating rate of 20 K/min in nitrogen atmosphere (flow rate: 40 mL/min). Finally, superficial topographic was analyzed by scanning electron microscopy (SEM). Dental composite evaluation suggests a high thermal stability and inorganic content in RES D sample. Degrees of conversion (DC) values were almost the same and there was no direct relationship between DC and amount of particles and size. Similar compositions were found in all samples.     

Characterization of fungal degraded lime wood by FT-IR and 2D IR correlation spectroscopy

The action of soft-rot fungus Chaetomium globosum has been studied. The decayed lime wood samples were observed for different periods of exposure. The degree of decay was determined by weight loss which was of 50.4% after 133 days. The samples were analyzed by FT-IR and 2D IR correlation spectroscopy.The intensity bands assigned to different vibrations from cellulose and hemicelluloses show a decrease, while the intensities of the bands assigned to C–O vibrations due to the formation of oxidized structures increase. At the same time, the intensity of the band assigned to C–O in metoxyl groups from lignin shows a decrease with increasing exposure time. The differences between reference and decayed wood spectra were examined in detail using 2D correlation spectroscopy and the second derivative analysis for two exposure time periods — of 0–70 days and 70–133 days. The formation of reactive species due to oxidation reactions induced by enzymes and the demethoxylation of the lignin structure was evidenced.     

Photo- and thermoinitiated oxidation of high-impact polystyrene. I. Characterization by FT-IR spectroscopy

The photo- and thermooxidative degradation of different grades of high-impact polystyrene (HIPS) has been studied by FT-IR spectroscopy. The oxidized films were treated with NH₃ and SF₄ for the rapid identification and resolution of the various carbonyl species, alcohols, and hydroperoxides. All the sample gave similar oxidation products, but in varying quantities. The heterogenity in the film was also determined by micro-FT-IR spectroscopy. The thermal degradation processes at different temperature were compared. © 1994 John Wiley & Sons, Inc.     

Characterization by fourier transform infrared spectroscopy (FT-IR) and 2D IR correlation spectroscopy of PAMAM dendrimer

FT-IR and 2D correlation spectroscopy were employed to study the microstructural changes occurring during phase transitions of a liquid crystal poly(amidoamine) codendrimer (PAMAM (L1)16(L2)16) generation 3, functionalized on the terminal groups by one-chain promesogenic calamitic units (4-(4'-decyloxybenzoyloxy)salicylaldehyde (L1)) and two-chain promesogenic calamitic units (4-(3',4'-didecyloxybenzoyloxy)salicylaldehyde (L2)). Spectral modifications associated with molecular conformation rearrangements allowing for molecular shape change on going from a liquid-crystalline organization to another were found. The transition temperatures were calculated, and they are in good agreement with the DSC data. Spectral analysis gives evidence of the LC phase transitions and to an additional transition associated with the existence of conformers. Various types of hydrogen bonding have been established.     

Characterization of nanostructured hybrid and organic solar cells by impedance spectroscopy

We review the application of impedance spectroscopy in dye-sensitized solar cells, quantum dot-sensitized solar cells and organic bulk heterojunction solar cells. We emphasize the interpretation of the impedance parameters for determining the internal features of the device, concerning the carrier distribution, materials properties such as the density of states and/or doping of the semiconductors, and the match of energy levels for photoinduced charge generation and separation. Another central task is the determination of recombination mechanisms from the measured resistances, and the factors governing the device performance by combined analysis of resistances as a function of voltage and current-voltage curves.     

Molecular imaging of paper cross sections by FT-IR spectroscopy and principal component analysis

The molecular imaging of paper cross sections containing the wet-strength additive poly(amidoamine)–epichlorohydrin (PAE) was effected by Fourier transform infrared (FT-IR) spectroscopic imaging. Thin cross sections of laboratory sheet samples were prepared and transferred onto CaF₂ substrates. A laboratory sheet sample without PAE acted as a reference. Principal component analysis (PCA) was applied to identify and to reveal the distribution of PAE across the section. Differences in the loading plots of the fourth and fifth principal components for the sheets with and without PAE were found in the region of the amide I, amide II, and amine bands within a variance of 0.4–0.8 %. The score images of the PCA reveal inhomogeneous distribution of PAE. Small areas of higher concentration of PAE occur across the cross section. The aim of this study was to demonstrate that FT-IR spectroscopic imaging provides spatially resolved quantitative information about the chemical composition of paper, which was successfully achieved.

Characterization and analysis of waxes by differential thermal analysis

The characterization of waxes by differential thermal analysis is described. An endothermic peak at 475-480 degrees is characteristic of microcrystalline and polyethylene waxes, and measurement of its area provides a method for the estimation of these waxes in mixtures.     

Thermal analysis and FT-IR spectroscopy of synthetic clay mineral mixtures

Journal of Thermal Analysis and Calorimetry - This article investigates the visualizations of heatlines in a natural convection magnetohydrodynamic flow from a vertical cylinder via heat function...     

A novel direct coupling of simultaneous thermal analysis (STA) and Fourier transform-infrared (FT-IR) spectroscopy

Evolved gas analysis (EGA) from thermal analyzers such as thermogravimetry (TG) or simultaneous thermal analysis (STA) which refers to simultaneous TG–DSC is well established since it greatly enhances the value of TG or TG–DSC results. The sensitive and selective FT-IR technique is in particular useful for the analysis of organic molecules but also for infrared active permanent gases evolved during most decomposition processes. The coupling interface between thermal analyzers and FT-IR spectrometers usually consists of heated adapters and a flexible, heated transfer line. In this work, a novel direct coupling of an STA instrument and an FT-IR spectrometer without a transfer line is presented. A very small FT-IR spectrometer is directly mounted on top of the STA furnace leading to a compact and fully integrated STA–FT-IR coupling system. The possibilities and the value of simultaneous STA–FT-IR measurements are demonstrated for organic, biomass, and ceramic samples in the temperature range between room temperature and about 1,500 °C. Various samples from the field of inorganics and organics—especially polymers—were furthermore measured showing the advantages of the direct STA–FT-IR coupling compared to state-of-the-art STA–FT-IR coupling using a heated transfer line: we found that the time delay caused by the volume of the transfer line itself is rather negligible whereas a significantly better correlation between gas detection and TG results was observed in case of some highly condensable decomposition gases. Aspects of quantification of evolved gases are furthermore discussed as well as the known nonlinearity of FT-IR detection at higher gas concentrations.     

Detailed FT-IR spectroscopy characterization and thermal analysis of synthesis of barium titanate nanoscale particles through a newly developed process

BaTiO₃ nanopowders were prepared at lower temperature and in shorter time span through a newly developed process. To reach an in-detail understanding of mechanism of the process, thermal analysis were performed using DTA/TGA and FT-IR techniques aided by in-depth discussions. The results indicated that thermal evolution of sol–gel-powder transformation consists of following steps: the vaporization of volatile organic solvents, the deformation of gel structure and pyrolysis of the Ba–Ti organic precursors, the decomposition of BaCO₃ into BaO and CO₂, reaction of resulted BaO with TiO₂ to form BaTiO₃. The results also elucidated the reaction pattern and formation mechanism of BaTiO₃ nanopowders from gel-derived precursor.     

Complex formation between aliphatic amines and chromogenic calix[4]arene derivatives studied by FT-IR spectroscopy

Complex formation of two calix[4]arene derivatives - containing two ethoxycarbonylmethoxy groups or a bridge including two carboxamide moieties in the coordination sphere - with aliphatic amines (n-octylamine, OA and triethylamine, TEA) were the subject of FT-IR studies. Two nitrophenyl type auxochromic moieties were also present in both of the ligands. Solvent effects were studied in chloroform, diiodomethane and dichloromethane. Presumably, in these reactions, the reactants undergo phenol-amine type interactions and, simultaneously, coordinative interaction takes place between the carbonyl group of the ligand and the protonated form of the aliphatic amine. Complex formation of calixarene 1a with n-octylamine was complete resulting in drastic changes in the FT-IR spectra. Moreover, the possibility of the formation of a new compound by the reaction between the ester type functionalities and octylamine was precluded. The expected ligand was synthesized and its spectra were compared with those of calixarene 1a. In most of the cases of calixarene 1b, the amide moiety of the carboxamide bridge does not participate in the complex formation with the exception of complexes formed in diiodomethane solution and of the 1b-TEA complex observed in dichloromethane.     

DNA analysis of a radiotolerant bacterium Pantoea agglomerans by FT-IR spectroscopy

A radiation tolerance strain, Pantoea agglomerans was isolated from γ-irradiated carrot samples (Daucus carota). D₁₀ determination showed that the radioresistance of this bacterium is five-fold higher than Escherichia coli, both belonging to the family of Enterobacteriaceae. DNA isolated from untreated and irradiated bacterial cells was analyzed by FT-IR spectroscopy to investigate the radiotolerance of this bacterium. At doses <5 kGy, an alteration of the interbase hydrogen networks was observed and characterized mainly by an increase of bands assigned to the carbonyl non-pairing and the free amine groups. Moderate breakage of the DNA backbone and damage of the osidic structure were also observed. Similar spectral profiles were noticed at doses ≥5 kGy, but additional increase of the band intensity of CC and CN suggests damages of nucleobases. High number of asymmetric PO₂⁻ and upper shift of symmetric PO₂⁻ are indicative of DNA strand breaks. Osidic damages were evidenced by decrease of the absorption bands ascribed to deoxyribosyl moieties and by appearance of C–OH band. DNA degradation at high irradiation doses was also noticed by electrophoresis using agarose gel. It appeared that DNA underwent covalent cross-linking, as revealed by agglomeration of DNA in the wells of agarose gel.     

Analysis of thermal phases in calcareous Iron Age pottery using FT-IR and Raman spectroscopy

The work deals with the FT-IR and micro-Raman spectroscopy study of the pseudo-amorphous and crystalline thermal phases in the composition of calcareous Iron Age pottery from the Galilee. The application of second-derivative and curve-fitting techniques improves the identification of the thermal phases in the composition of the pottery and makes it possible to analyze the pseudo-amorphous phases which are formed during the firing of the clayey raw material to pottery. This technique makes it possible to distinguish between meta-smectite and meta-kaolinite and to estimate the firing temperature of the pottery. The Micro-Raman spectroscopy is sensitive to the structural degree of ordering of the thermal phases and enables point analysis of peculiar components in the composition of the pottery. Based on the spectroscopic study, it is concluded that the calcareous pottery contained large amounts of microcrystalline-recarbonated calcite mixed with the meta-clay. The large amount of recarbonated calcite in the pottery material and the relatively low firing temperature indicates that instead of sintering the clay, lime technology was used for the cementation of the calcareous vessels. This process took place after the firing by recarbonation of the decomposed calcite which leads to cementation of the vessels with microcrystalline calcite.     

Mechanical and thermal properties of poly(3-hydroxybutyrate) blends with starch and starch derivatives

Poly(3-hydroxybutyrate) (PHB) is a highly crystalline, biodegradable and biocompatible thermoplastic. However, its limited utilization as a commodity plastic is associated to both high cost and very poor mechanical properties. Blending PHB with a natural polymer, such as starch, is one way to improve its properties and to get low price raw materials, though they are not miscible since there are no strong interactions between the hydrophilic starch and the hydrophobic PHB. In this study binary blends of PHB were prepared with natural starch, starch-adipate and grafted starch-urethane derivatives. The PHB blends were characterized in terms of their mechanical and thermal properties. For all blends a decrease of the Young modulus was observed as compared to the pure PHB. However, blends containing natural starches and starch adipate resulted in brittle materials. A significant decrease of both glass transition temperature (Tg) and melting point (Tm) was observed for all formulations. The best results, lower modulus and Tg were obtained with grafted starch-urethane blends using poly(propylene glycol).     

Quantitative analysis of synthetic calcium carbonate polymorphs using FT-IR spectroscopy

Fourier Transform Infrared Spectroscopy (FT-IR) was used successfully for the simultaneous quantitative analysis of calcium carbonate phases (calcite, aragonite, vaterite) in ternary mixtures. From the FT-IR spectra of pure calcite, aragonite and vaterite powders with KBr, the absorptivities, α, of the absorption bands at 713 cm⁻¹ for calcite, 745 cm⁻¹ for vaterite, 713 and 700 cm⁻¹ for aragonite, were determined. In order to overcome the absorption band overlapping a set of equations based on Beer's law was developed. The detection limits were also established and found to be 1.1×10⁻⁴ mg calcite per mm² of pellet at 713 cm⁻¹, 3.6×10⁻⁴ mg aragonite per mm² of pellet at 700 cm⁻¹, 1.8×10⁻⁴ mg aragonite per mm² of pellet at 713 cm⁻¹ and 3.1×10⁻⁴ mg vaterite per mm² of pellet at 745 cm⁻¹. Analysis of a known ternary mixture of calcium carbonate polymorphs tested the validity of the method.