Capture of phosphates in surface water by TiO2 nanoparticles under UV irradiation

The capture of orthophosphates and total phosphorus from the Pudong Canal river in the Pudong District of Shanghai by TiO₂ nanoparticles is studied using a rotating photoreactor and the nano-TiO₂ photocatalyst Degussa P25. The effects of UV irradiation intensity in a range of 20–74 mW/cm², the loading of the TiO₂ nanoparticles in a range of 0.05–0.1 g/L, irradiation time up to 4 h, and pH values in a range of 2–10.5 on the capture efficiency are investigated. The results show that the capture of orthophosphates and total P are significantly enhanced by UV irradiation; at a loading of 0.1 g/L and an irradiation intensity above 36 mW/cm², orthophosphates and total phosphorus are rapidly captured by TiO₂ nanoparticles, causing an observed reduction from 0.4 mg/L down to 0.02 mg/L. pH values in a range of 2–10.5 have little effect on the capture efficiency of orthophosphates and total phosphorus.     

Chemical characteristics of PM2.5 during dust storms and air pollution events in Chengdu,China

Daily fine particulate (PM_2.5) samples were collected in Chengdu from April 2009 to February 2010 to investigate their chemical profiles during dust storms (DSs) and several types of pollution events, including haze (HDs), biomass burning (BBs), and fireworks displays (FDs). The highest PM_2.5 mass concentrations were found during DSs (283.3 μg/m³), followed by FDs (212.7 μg/m³), HDs (187.3 μg/m³), and BBs (130.1 μg/m³). The concentrations of most elements were elevated during DSs and pollution events, except for BBs. Secondary inorganic ions (NO₃^?, SO₄^2?, and NH₄⁺) were enriched during HDs, while PM_2.5 from BBs showed high K⁺ but low SO₄^2?. FDs caused increases in K⁺ and enrichment in SO₄^2?. Ca²⁺ was abundant in DS samples. Ion-balance calculations indicated that PM_2.5 from HDs and FDs was more acidic than on normal days, but DS and BB particles were alkaline. The highest organic carbon (OC) concentration was 26.1 μg/m³ during FDs, followed by BBs (23.6 μg/m³), HDs (19.6 μg/m³), and DSs (18.8 μg/m³). In contrast, elemental carbon (EC) concentration was more abundant during HDs (10.6 μg/m³) and FDs (9.5 μg/m³) than during BBs (6.2 μg/m³) and DSs (6.0 μg/m³). The highest OC/EC ratios were obtained during BBs, with the lowest during HDs. SO₄^2?/K⁺ and TCA/SO₄^2? ratios proved to be effective indicators for differentiating pollution events. Mass balance showed that organic matter, SO₄^2?, and NO₃^? were the dominant chemical components during pollution events, while soil dust was dominant during DSs.     

Real-time measurements of PM2.5, PM10–2.5, and BC in an urban street canyon

A continuous dichotomous beta gauge monitor was used to characterize the hourly content of PM_2.5, PM_10–2.5, and Black Carbon (BC) over a 12-month period in an urban street canyon of Hong Kong. Hourly vehicle counts for nine vehicle classes and meteorological data were also recorded. The average weekly cycles of PM_2.5, PM_10–2.5, and BC suggested that all species are related to traffic, with high concentrations on workdays and low concentrations over the weekends. PM_2.5 exhibited two comparable concentrations at 10:00–11:00 (63.4 μg/m³) and 17:00–18:00 (65.0 μg/m³) local time (LT) during workdays, corresponding to the hours when the numbers of diesel-fueled and gasoline-fueled vehicles were at their maximum levels: 3179 and 2907 h⁻¹, respectively. BC is emitted mainly by diesel-fueled vehicles and this showed the highest concentration (31.2 μg/m³) during the midday period (10:00–11:00 LT) on workdays. A poor correlation was found between PM_2.5 concentration and wind speed (R = 0.51, P-value > 0.001). In contrast, the concentration of PM_10–2.5 was found to depend upon wind speed and it increased with obvious statistical significance as wind speed increased (R = 0.98, P-value < 0.0001).     

Fabrication of magnetic nanosized γ-FeNi-coated ceramic core–shell microspheres by heterogeneous precipitation and thermal reduction

Precursors with NiCO₃·2Ni(OH)₂·2H₂O- and Fe₂O₃·nH₂O-coated alumina, graphite and cenosphere were synthesized by precipitation using ferrous sulfate, nickel sulfate, ammonium bicarbonate, alumina, graphite and cenosphere as the main starting materials. Magnetic γ-FeNi-coated alumina, graphite and cenosphere core–shell structural microspheres were subsequently prepared by thermal reduction of the as-prepared precursors at 600 °C for 2 h. Precipitation parameters, e.g. concentration of ceramic micropowders (10 g/L), sulfate solution (0.2 mol/L), rate of adding reactants (3 mL/min) and pH value were optimized by a trial-and-error method. Powders of the precursors and the resulting coating of γ-FeNi with grain size below 40 nm on alumina, graphite and cenosphere microspheres were characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The magnetic properties of the nanosize γ-FeNi-coated alumina, graphite and cenosphere microspheres were measured by vibrating sample magnetometer (VSM). The results show that the core–shell structural γ-FeNi-coated ceramic microspheres exhibited higher coercivity than pure γ-FeNi powders, indicating that these materials can be used for high-performance functional materials and devices.     

Observation and analysis of near-surface atmospheric aerosol optical properties in urban Beijing

Year-round measurements of the mass concentration and optical properties of fine aerosols (PM_2.5) from June 2009 to May 2010 at an urban site in Beijing were analyzed. The annual mean values of the PM_2.5 mass concentration, absorption coefficient (Ab), scattering coefficient (Sc) and single scattering albedo (SSA) at 525 nm were 67 ± 66 μg/m³, 64 ± 62 Mm⁻¹, 360 ± 405 Mm⁻¹ and 0.82 ± 0.09, respectively. The bulk mass absorption efficiency and scattering efficiency of the PM_2.5 at 525 nm were 0.78 m²/g and 5.55 m²/g, respectively. The Ab and Sc showed a similar diurnal variation with a maximum at night and a minimum in the afternoon, whereas SSA displayed an opposite diurnal pattern. Significant increases in the Ab and Sc were observed in pollution episodes caused by the accumulation of pollutants from both local and regional sources under unfavorable weather conditions. Aerosol loadings in dust events increased by several times in the spring, which had limited effects on the Ab and Sc due to the low absorption and scattering efficiency of dust particles. The frequency of haze days was the highest in autumn because of the high aerosol absorption and scattering under unfavorable weather conditions. The daily PM_2.5 concentration should be controlled to a level lower than 64 μg/m³ to prevent the occurrence of haze days according to its exponentially decreased relationship with visibility.     

Spatiotemporal variations of PM2.5 and PM10 concentrations between 31 Chinese cities and their relationships with SO2, NO2, CO and O3

The variations of mass concentrations of PM_2.5, PM₁₀, SO₂, NO₂, CO, and O₃ in 31 Chinese provincial capital cities were analyzed based on data from 286 monitoring sites obtained between March 22, 2013 and March 31, 2014. By comparing the pollutant concentrations over this length of time, the characteristics of the monthly variations of mass concentrations of air pollutants were determined. We used the Pearson correlation coefficient to establish the relationship between PM_2.5, PM₁₀, and the gas pollutants. The results revealed significant differences in the concentration levels of air pollutants and in the variations between the different cities. The Pearson correlation coefficients between PMs and NO₂ and SO₂ were either high or moderate (PM_2.5 with NO₂: r = 0.256–0.688, mean r = 0.498; PM₁₀ with NO₂: r = 0.169–0.713, mean r = 0.493; PM_2.5 with SO₂: r = 0.232–0.693, mean r = 0.449; PM₁₀ with SO₂: r = 0.131–0.669, mean r = 0.403). The correlation between PMs and CO was diverse (PM_2.5: r = 0.156–0.721, mean r = 0.437; PM₁₀: r = 0.06–0.67, mean r = 0.380). The correlation between PMs and O₃ was either weak or uncorrelated (PM_2.5: r = −0.35 to 0.089, mean r = −0.164; PM₁₀: r = −0.279 to 0.078, mean r = −0.127), except in Haikou (PM_2.5: r = 0.500; PM₁₀: r = 0.509).     

Fabrication of nano-sized Ca(OH)2 with excellent adsorption ability for N2O4

Uniform nano-sized calcium hydroxide (Ca(OH)₂) monocrystal powder was synthesized from calcium oxide in a surfactant solution via a digestion method by decreasing the surface tension of the reaction system to control the growth of crystalline Ca(OH)₂. The Ca(OH)₂ monocrystal powder samples were characterized by means of scanning electron microscopy (SEM), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET), and Fourier transform-infrared spectroscopy (FT-IR). The NO_x adsorption ability of the samples was evaluated, and the influence of various types and concentrations of surfactants on powder agglomeration and then the specific surface area in the precipitation process were studied. The specific surface area of the samples was found as high as 58 m²/g and 92 m²/g and the particle size, 300–400 nm and 200–300 nm in the presence of 10 wt% PEG600 and 0.086 mL/L SDS at a reaction time of 5 h, respectively. The product has an exceptionally strong adsorption ability for NO_x, which makes it a highly promising adsorbent for emission control and air purification.     

Experimental and computational studies of shock wave-to-bubbly water momentum transfer

Momentum transfer from shock waves (SWs) of various intensity (from 0.05 MPa to 0.5 MPa in amplitude) to water containing air bubbles 2.5 to 4 mm of mean diameter is studied both experimentally and by means of numerical simulation. Experiments are performed in a vertical shock tube of a 50 × 100 mm² rectangular cross section consisting of a 495-mm long high-pressure section (HPS), 495-mm long low-pressure section (LPS), and 990 mm long test section (TS) equipped with an air bubbler and filled with water. Experiments have shown that as the initial gas volume fraction in water increases from 0 to 0.3 the momentum imparted in bubbly water by SWs increases monotonically, gradually levelling off at an air volume fraction of about 0.30. The experimental data are confirmed by two-dimensional (2D) simulation of SW propagation in bubbly water in terms of the SW velocity versus the air content, pressure profiles, as well as liquid and gas velocity behind the shock front.     

Effect of projectile nose shape on the ballistic resistance of ductile targets

Three-dimensional numerical simulations were carried out to study the ballistic resistance of ductile targets subjected to normal impact by the projectiles. 12 mm thick Weldox 460 E steel targets were impacted by 20 mm diameter conical nosed projectiles and 1 mm thick 1100-H12 aluminum targets were impacted by 19 mm diameter ogive nosed projectiles. The internal nose angle of conical projectile was varied (33.4°–180°) and found to have significant effect on the ballistic limit of 12 mm thick Weldox 460 E steel target. Similarly, the caliber radius head (CRH) of ogive nosed projectile was varied (0–2.5) and found to have significant effect on the ballistic limit of 1 mm thick 1100-H12 aluminum target. The ballistic limit of 12 mm thick Weldox 460 E steel target increased almost linearly with the decrease in the projectile nose angle. While the ballistic limit of 1 mm thick 1100-H12 aluminum target increased as the CRH increased from 0 to 0.5 and with further increase in CRH to 1.0, 1.5, 2.0 and 2.5 its values were found to drop quite significantly. ABAQUS/Explicit finite element code was used to carry out the numerical simulations.     

Molecular distribution and seasonal variation of hydrocarbons in PM2.5 from Beijing during 2006

Normal (n)-alkanes and polycyclic aromatic hydrocarbons (PAHs) in PM_2.5 were collected from Beijing in 2006 and analyzed using a thermal desorption-GC/MS technique. Annual average concentrations of n-alkanes and PAHs were 282 ± 96 and 125 ± 150 ng/m³, respectively: both were highest in winter and lowest in summer. C₁₉–C₂₅ compounds dominated the n-alkanes while benzo[b]fluoranthene, benzo[e]pyrene, and phenanthrene were the most abundant PAHs. The n-alkanes exhibited moderate correlations with organic carbon (OC) and elemental carbon (EC) throughout the year, but the relationships between the PAHs, OC and EC differed between the heating and non-heating seasons. The health risks associated with PAHs in winter were more than 40 times those in spring and summer even though the PM_2.5 loadings were comparable. Carbon preference index values (<1.5) indicated that the n-alkanes were mostly from fossil fuel combustion. The ratios of indeno[123-cd]pyrene to benzo[ghi]pyrelene in summer and spring were 0.58 ± 0.12 and 0.63 ± 0.09, respectively, suggesting that the PAHs mainly originated from motor vehicles, but higher ratios in winter reflected an increased influence from coal, which is extensively burned for domestic heating. A comprehensive comparison showed that PAH pollution in Beijing has decreased in the past 10 years.     

Discrete element method simulations of Mars Exploration Rover wheel performance

Mars Exploration Rovers (MERs) experienced mobility problems during traverses. Three-dimensional discrete element method (DEM) simulations of MER wheel mobility tests for wheel slips of i = 0, 0.1, 0.3, 0.5, 0.7, 0.9, and 0.99 were done to examine high wheel slip mobility to improve the ARTEMIS MER traverse planning tool. Simulations of wheel drawbar pull and sinkage MIT data for i ⩽ 0.5 were used to determine DEM particle packing density (0.62) and contact friction (0.8) to represent the simulant used in mobility tests. The DEM simulations are in good agreement with MIT data for i = 0.5 and 0.7, with reasonable but less agreement at lower wheel slip. Three mobility stages include low slip (i < 0.3) controlled by soil strength, intermediate slip (i ∼ 0.3–0.6) controlled by residual soil strength, and high slip (i > 0.6) controlled by residual soil strength and wheel sinkage depth. Equilibrium sinkage occurred for i < 0.9, but continuously increased for i = 0.99. Improved DEM simulation accuracy of low-slip mobility can be achieved using polyhedral particles, rather than tri-sphere particles, to represent soil. The DEM simulations of MER wheel mobility can improve ARTEMIS accuracy.     

Microwave-hydrothermal preparation of a graphene/hierarchy structure MnO2 composite for a supercapacitor

Graphene/hierarchy structure manganese dioxide (GN/MnO₂) composites were synthesized using a simple microwave-hydrothermal method. The properties of the prepared composites were analyzed using field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) measurements. The electrochemical performances of the composites were analyzed using cyclic voltammetry, electrochemical impedance spectrometry (EIS), and chronopotentiometry. The results showed that GN/MnO₂ (10 wt% graphene) displayed a specific capacitance of 244 F/g at a current density of 100 mA/g. An excellent cyclic stability was obtained with a capacity retention of approximately 94.3% after 500 cycles in a 1 mol/L Li₂SO₄ solution. The improved electrochemical performance is attributed to the hierarchy structure of the manganese dioxide, which can enlarge the interface between the active materials and the electrolyte. The preparation route provides a new approach for hierarchy structure graphene composites; this work could be readily extended to the preparation of other graphene-based composites with different structures for use in energy storage devices.     

Characteristics of black carbon aerosol in Jiaxing,China during autumn 2013

We conducted measurements of black carbon (BC) aerosol in Jiaxing, China during autumn from September 26 to November 30, 2013. We investigated temporal and diurnal variations of BC, and its correlations with meteorological parameters and other major pollutants. Results showed that hourly mass concentrations of BC ranged from 0.2 to 22.0 μg/m³, with an average of 5.1 μg/m³. The diurnal variation of BC exhibited a bimodal distribution, with peaks at 07:00 and 18:00. The morning peak was larger than the evening peak. The mass percentages of BC in PM_2.5 and PM₁₀ were 7.1% and 4.8%, respectively. The absorption coefficient of BC was calculated to be 44.4 Mm⁻¹, which accounted for 11.1% of the total aerosol extinction. BC was mainly emitted from local sources in southwestern Jiaxing where BC concentrations were generally greater than 11 μg/m³ during the measurement period. Correlation analysis indicated that the main sources of BC were motor vehicle exhaust, and domestic and industrial combustion.     

Green synthesis and enhanced photocatalytic activity of Ce-doped TiO2 nanoparticles supported on porous glass

A facile and green method to prepare Ce-doped TiO₂ nanoparticles supported on porous glass beads is reported. An ion exchange process and subsequent calcination yielded Ce-doped TiO₂ nanoparticles with a mean size of 4.8 ± 0.3 nm. The nanoparticles were dispersed on the surface of porous glass beads. The addition of Ce enhanced the visible light absorption of the TiO₂ nanoparticles in the 400–500 nm spectral window. The band gap of the as-prepared catalyst was 2.80 eV. The Ce-doped TiO₂ nanoparticles immobilized on porous glass beads exhibited excellent photocatalytic activity for the visible-light-degradation of methyl orange (MO) and rhodamine B (RhB); with rate constants of 0.095 and 0.230 min⁻¹; respectively. The effects of Ce dosage; reaction duration; and initial solution pH on the conversion of MO and RhB dyes were investigated. The green synthesis and favorable photocatalytic activity makes the Ce-doped TiO₂ nanoparticles immobilized on porous glass an attractive alternative for the efficient degradation of organic pollutants.     

Chemical characteristics of PM2.5 during haze episodes in the urban of Fuzhou,China

Atmospheric fine particles (PM_2.5) were collected in this study with middle volume samplers in Fuzhou, China, during both normal days and haze days in summer (September 2007) and winter (January 2008). The concentrations, distributions, and sources of polycyclic aromatic hydrocarbons (PAHs), organic carbon (OC), elemental carbon (EC), and water soluble inorganic ions (WSIIs) were determinated. The results showed that the concentrations of PM_2.5, PAHs, OC, EC, and WSIIs were in the orders of haze > normal and winter > summer. The dominant PAHs of PM_2.5 in Fuzhou were Fluo, Pyr, Chr, BbF, BkF, BaP, BghiP, and IcdP, which represented about 80.0% of the total PAHs during different sampling periods. The BaPeq concentrations of ∑PAHs were 0.78, 0.99, 1.22, and 2.43 ng/m³ in summer normal, summer haze, winter normal, and winter haze, respectively. Secondary pollutants (SO₄^2?, NO₃^?, NH₄⁺, and OC) were the major chemical compositions of PM_2.5, accounting for 69.0%, 55.1%, 63.4%, and 64.9% of PM_2.5 mass in summer normal, summer haze, winter normal, and winter haze, respectively. Correspondingly, secondary organic carbon (SOC) in Fuzhou accounted for 20.1%, 48.6%, 24.5%, and 50.5% of OC. The average values of nitrogen oxidation ratio (NOR) and sulfur oxidation ratio (SOR) were higher in haze days (0.08 and 0.27) than in normal days (0.05 and 0.22). Higher OC/EC ratios were also found in haze days (5.0) than in normal days (3.3). Correlation analysis demonstrated that visibility had positive correlations with wind speed, and negative correlations with relative humidity and major air pollutants. Overall, the enrichments of PM_2.5, OC, EC, SO₄^2?, and NO₃^? promoted haze formation. Furthermore, the diagnostic ratios of IcdP/(IcdP + BghiP), IcdP/BghiP, OC/EC, and NO₃^?/SO₄^2? indicated that vehicle exhaust and coal consumption were the main sources of pollutants in Fuzhou.     

Variation of PM2.5 concentration in Hangzhou,China

This observational study investigates the variation of PM_2.5 concentration and its ratio against PM₁₀ concentration under different weather systems and pollution types. The study was conducted in Hangzhou on east China's Yangtze River Delta using data collected at seven ambient air quality monitoring stations around the metropolitan area between 2006 and 2008 and using weather information in the same period. Nine predominant weather systems affecting the city were classified through careful analysis of the 11-year surface and upper air weather charts from 1996 to 2006. Each observational day was then assigned to one of the nine weather systems. It was found that the PM_2.5 concentration varied greatly for different weather systems, with the highest PM_2.5 concentration associated with the post-cold-frontal system at 0.091 mg/m³ and the lowest PM_2.5 concentration with the easterlies system at 0.038 mg/m³, although the PM_2.5/PM₁₀ ratio remained consistently above 0.5 for all systems. The post-cold-frontal system typically occurs in autumn and winter while the easterlies system is more a summer phenomenon. Among all types of pollution, the highest PM_2.5 concentration of 0.117 mg/m³ coincided with the large-scale continuous pollution events, suggesting that this type of pollution was more conducive to the formation of secondary particulate matters. The ratio of PM_2.5/PM₁₀ was above 0.5 in non-pollution days and all pollution types but one under the influence of dust storms when the ratio decreased to 0.3 or less. The outcomes of this study could be used to develop a rudimental predictive model of PM_2.5 concentration based on weather system and pollution type.     

Analysis of the causes of heavy aerosol pollution in Beijing,China: A case study with the WRF-Chem model

The causes and variability of a heavy haze episode in the Beijing region was analyzed. During the episode, the PM_2.5 concentration reached a peak value of 450 μg/kg on January 18, 2013 and rapidly decreased to 100 μg/kg on January 19, 2013, characterizing a large variability in a very short period. This strong variability provides a good opportunity to study the causes of the haze formation. The in situ measurements (including surface meteorological data and vertical structures of the winds, temperature, humidity, and planetary boundary layer (PBL)) together with a chemical/dynamical regional model (WRF-Chem) were used for the analysis. In order to understand the rapid variability of the PM_2.5 concentration in the episode, the correlation between the measured meteorological data (including wind speed, PBL height, relative humidity, etc.) and the measured particle concentration (PM_2.5 concentration) was studied. In addition, two sensitive model experiments were performed to study the effect of individual contribution from local emissions and regional surrounding emissions to the heavy haze formation. The results suggest that there were two major meteorological factors in controlling the variability of the PM_2.5 concentration, namely, surface wind speed and PBL height. During high wind periods, the horizontal transport of aerosol particles played an important role, and the heavy haze was formed when the wind speeds were very weak (less than 1 m/s). Under weak wind conditions, the horizontal transport of aerosol particles was also weak, and the vertical mixing of aerosol particles played an important role. As a result, the PBL height was a major factor in controlling the variability of the PM_2.5 concentration. Under the shallow PBL height, aerosol particles were strongly confined near the surface, producing a high surface PM_2.5 concentration. The sensitivity model study suggests that the local emissions (emissions from the Beijing region only) were the major cause for the heavy haze events. With only local emissions, the calculated peak value of the PM_2.5 concentration was 350 μg/kg, which accounted for 78% of the measured peak value (450 μg/kg). In contrast, without the local emissions, the calculated peak value of the PM_2.5 concentration was only 100 μg/kg, which accounted for 22% of the measured peak value.     

Numerical investigation of particle deposition inside aero-shielded solar cyclone reactor: A promising solution for reactor clogging

Solar cracking of methane is considered to be an attractive option due to its CO₂ free hydrogen production process. Carbon particle deposition on the reactor window, walls and exit is a major obstacle to achieve continuous operation of methane cracking solar reactors. As a solution to this problem a novel “aero-shielded solar cyclone reactor” was created. In this present study the prediction of particle deposition at various locations for the aero-shielded reactor is numerically investigated by a Lagrangian particle dispersion model. A detailed three dimensional computational fluid dynamic (CFD) analysis for carbon deposition at the reactor window, walls and exit is presented using a Discrete Phase Model (DPM). The flow field is based on a RNG k–ε model and species transport with methane as the main flow and argon/ hydrogen as window and wall screening fluid. Flow behavior and particle deposition have been observed with the variation of main flow rates from 10–20 L/min and with carbon particle mass flow rate of 7 × 10⁻⁶ and 1.75 × 10⁻⁵ kg/s. In this study the window and wall screening flow rates have been considered to be 1 L/min and 10 L/min by employing either argon or hydrogen. Also, to study the effect of particle size simulations have also been carried out (i) with a variation of particle diameter with a size distribution of 0.5–234 μm and (ii) by taking 40 μm mono sized particles which is the mean value for the considered size distribution. Results show that by appropriately selecting the above parameters, the concept of the aero-shielded reactor can be an attractive option to resolve the problem of carbon deposition at the window, walls and exit of the reactor.     

Emission of organic carbon,elemental carbon and water-soluble ions from crop straw burning under flaming and smoldering conditions

Emissions from major agricultural residues were measured using a self-designed combustion system. Emission factors (EFs) of organic carbon (OC), elemental carbon (EC), and water-soluble ions (WSIs) (K⁺, NH₄⁺, Na⁺, Mg²⁺, Ca²⁺, Cl⁻, NO₃⁻, SO₄^2–) in smoke from wheat and rice straw were measured under flaming and smoldering conditions. The OC₁/TC (total carbon) was highest (45.8% flaming, 57.7% smoldering) among carbon fractions. The mean EFs for OC (EF_OC) and EC (EF_EC) were 9.2 ± 3.9 and 2.2 ± 0.7 g/kg for wheat straw and 6.4 ± 1.9 and 1.1 ± 0.3 g/kg for rice straw under flaming conditions, while they were 40.8 ± 5.6 and 5.8 ± 1.0 g/kg and 37.6 ± 6.3 and 5.0 ± 1.4 g/kg under smoldering conditions, respectively. Higher EC ratios were observed in particulate matter (PM) mass under flaming conditions. The OC and EC for the two combustion patterns were significantly correlated (p < 0.01, R = 0.95 for wheat straw; p < 0.01, R = 0.97 for rice straw), and a higher positive correlation between OC₃ and EC was observed under both combustion conditions. WSIs emitted from flaming smoke were dominated by Cl⁻ and K⁺, which contributed 3.4% and 2.4% of the PM mass for rice straw and 2.2% and 1.0% for wheat straw, respectively. The EFs of Cl⁻ and K⁺ were 0.73 ± 0.16 and 0.51 ± 0.14 g/kg for wheat straw and 0.25 ± 0.15 and 0.12 ± 0.05 g/kg for rice straw under flaming conditions, while they were 0.42 ± 0.28 and 0.12 ± 0.06 g/kg and 0.30 ± 0.27 and 0.05 ± 0.03 g/kg under smoldering conditions, respectively. Na⁺, Mg²⁺, and NH₄⁺ were vital components in PM, comprising from 0.8% (smoldering) to 3.1% (flaming) of the mass. Strong correlations of Cl⁻ with K⁺, NH₄⁺, and Na⁺ ions were observed in rice straw and the calculated diagnostic ratios of OC/EC, K⁺/Na⁺ and Cl⁻/Na⁺ could be useful to distinguishing crop straw burning from other sources of atmospheric pollution.     

Impact of meteorological conditions on a nine-day particulate matter pollution event observed in December 2013, Shanghai,China

A severe particulate matter pollution event occurred in Shanghai from 1 to 9 December 2013. The mean hourly mass concentrations of PM_2.5 and PM₁₀ were 211.9 and 249.0 μg/m³, respectively. Reanalysis data, in situ, and remote-sensing measurements were used to examine the impacts of meteorological conditions on this event. It was found that the synoptic pattern of weak pressure, the reduced planetary boundary layer height, and the passage of two cold fronts were key factors causing the event. Four stages were identified during this event based on the evolution of its PM_2.5 levels and weather conditions. The highest concentration of PM_2.5 (602 μg/m³) was observed in stage 3. High PM_2.5 concentrations were closely associated with a low local ventilation index, with an average of 505 m²/s, as well as with the influx of pollutants from upstream, transported by the cold fronts.